// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * hfcmulti.c  low level driver for hfc-4s/hfc-8s/hfc-e1 based cards
 *
 * Author       Andreas Eversberg (jolly@eversberg.eu)
 * ported to mqueue mechanism:
 *              Peter Sprenger (sprengermoving-bytes.de)
 *
 * inspired by existing hfc-pci driver:
 * Copyright 1999  by Werner Cornelius (werner@isdn-development.de)
 * Copyright 2008  by Karsten Keil (kkeil@suse.de)
 * Copyright 2008  by Andreas Eversberg (jolly@eversberg.eu)
 *
 * Thanks to Cologne Chip AG for this great controller!
 */

/*
 * module parameters:
 * type:
 *      By default (0), the card is automatically detected.
 *      Or use the following combinations:
 *      Bit 0-7   = 0x00001 = HFC-E1 (1 port)
 * or   Bit 0-7   = 0x00004 = HFC-4S (4 ports)
 * or   Bit 0-7   = 0x00008 = HFC-8S (8 ports)
 *      Bit 8     = 0x00100 = uLaw (instead of aLaw)
 *      Bit 9     = 0x00200 = Disable DTMF detect on all B-channels via hardware
 *      Bit 10    = spare
 *      Bit 11    = 0x00800 = Force PCM bus into slave mode. (otherwise auto)
 * or   Bit 12    = 0x01000 = Force PCM bus into master mode. (otherwise auto)
 *      Bit 13    = spare
 *      Bit 14    = 0x04000 = Use external ram (128K)
 *      Bit 15    = 0x08000 = Use external ram (512K)
 *      Bit 16    = 0x10000 = Use 64 timeslots instead of 32
 * or   Bit 17    = 0x20000 = Use 128 timeslots instead of anything else
 *      Bit 18    = spare
 *      Bit 19    = 0x80000 = Send the Watchdog a Signal (Dual E1 with Watchdog)
 * (all other bits are reserved and shall be 0)
 *      example: 0x20204 one HFC-4S with dtmf detection and 128 timeslots on PCM
 *               bus (PCM master)
 *
 * port: (optional or required for all ports on all installed cards)
 *      HFC-4S/HFC-8S only bits:
 *      Bit 0     = 0x001 = Use master clock for this S/T interface
 *                          (only once per chip).
 *      Bit 1     = 0x002 = transmitter line setup (non capacitive mode)
 *                          Don't use this unless you know what you are doing!
 *      Bit 2     = 0x004 = Disable E-channel. (No E-channel processing)
 *      example: 0x0001,0x0000,0x0000,0x0000 one HFC-4S with master clock
 *               received from port 1
 *
 *      HFC-E1 only bits:
 *      Bit 0     = 0x0001 = interface: 0=copper, 1=optical
 *      Bit 1     = 0x0002 = reserved (later for 32 B-channels transparent mode)
 *      Bit 2     = 0x0004 = Report LOS
 *      Bit 3     = 0x0008 = Report AIS
 *      Bit 4     = 0x0010 = Report SLIP
 *      Bit 5     = 0x0020 = Report RDI
 *      Bit 8     = 0x0100 = Turn off CRC-4 Multiframe Mode, use double frame
 *                           mode instead.
 *      Bit 9     = 0x0200 = Force get clock from interface, even in NT mode.
 * or   Bit 10    = 0x0400 = Force put clock to interface, even in TE mode.
 *      Bit 11    = 0x0800 = Use direct RX clock for PCM sync rather than PLL.
 *                           (E1 only)
 *      Bit 12-13 = 0xX000 = elastic jitter buffer (1-3), Set both bits to 0
 *                           for default.
 * (all other bits are reserved and shall be 0)
 *
 * debug:
 *      NOTE: only one debug value must be given for all cards
 *      enable debugging (see hfc_multi.h for debug options)
 *
 * poll:
 *      NOTE: only one poll value must be given for all cards
 *      Give the number of samples for each fifo process.
 *      By default 128 is used. Decrease to reduce delay, increase to
 *      reduce cpu load. If unsure, don't mess with it!
 *      Valid is 8, 16, 32, 64, 128, 256.
 *
 * pcm:
 *      NOTE: only one pcm value must be given for every card.
 *      The PCM bus id tells the mISDNdsp module about the connected PCM bus.
 *      By default (0), the PCM bus id is 100 for the card that is PCM master.
 *      If multiple cards are PCM master (because they are not interconnected),
 *      each card with PCM master will have increasing PCM id.
 *      All PCM buses with the same ID are expected to be connected and have
 *      common time slots slots.
 *      Only one chip of the PCM bus must be master, the others slave.
 *      -1 means no support of PCM bus not even.
 *      Omit this value, if all cards are interconnected or none is connected.
 *      If unsure, don't give this parameter.
 *
 * dmask and bmask:
 *      NOTE: One dmask value must be given for every HFC-E1 card.
 *      If omitted, the E1 card has D-channel on time slot 16, which is default.
 *      dmask is a 32 bit mask. The bit must be set for an alternate time slot.
 *      If multiple bits are set, multiple virtual card fragments are created.
 *      For each bit set, a bmask value must be given. Each bit on the bmask
 *      value stands for a B-channel. The bmask may not overlap with dmask or
 *      with other bmask values for that card.
 *      Example: dmask=0x00020002 bmask=0x0000fffc,0xfffc0000
 *              This will create one fragment with D-channel on slot 1 with
 *              B-channels on slots 2..15, and a second fragment with D-channel
 *              on slot 17 with B-channels on slot 18..31. Slot 16 is unused.
 *      If bit 0 is set (dmask=0x00000001) the D-channel is on slot 0 and will
 *      not function.
 *      Example: dmask=0x00000001 bmask=0xfffffffe
 *              This will create a port with all 31 usable timeslots as
 *              B-channels.
 *      If no bits are set on bmask, no B-channel is created for that fragment.
 *      Example: dmask=0xfffffffe bmask=0,0,0,0.... (31 0-values for bmask)
 *              This will create 31 ports with one D-channel only.
 *      If you don't know how to use it, you don't need it!
 *
 * iomode:
 *      NOTE: only one mode value must be given for every card.
 *      -> See hfc_multi.h for HFC_IO_MODE_* values
 *      By default, the IO mode is pci memory IO (MEMIO).
 *      Some cards require specific IO mode, so it cannot be changed.
 *      It may be useful to set IO mode to register io (REGIO) to solve
 *      PCI bridge problems.
 *      If unsure, don't give this parameter.
 *
 * clockdelay_nt:
 *      NOTE: only one clockdelay_nt value must be given once for all cards.
 *      Give the value of the clock control register (A_ST_CLK_DLY)
 *      of the S/T interfaces in NT mode.
 *      This register is needed for the TBR3 certification, so don't change it.
 *
 * clockdelay_te:
 *      NOTE: only one clockdelay_te value must be given once
 *      Give the value of the clock control register (A_ST_CLK_DLY)
 *      of the S/T interfaces in TE mode.
 *      This register is needed for the TBR3 certification, so don't change it.
 *
 * clock:
 *      NOTE: only one clock value must be given once
 *      Selects interface with clock source for mISDN and applications.
 *      Set to card number starting with 1. Set to -1 to disable.
 *      By default, the first card is used as clock source.
 *
 * hwid:
 *      NOTE: only one hwid value must be given once
 *      Enable special embedded devices with XHFC controllers.
 */

/*
 * debug register access (never use this, it will flood your system log)
 * #define HFC_REGISTER_DEBUG
 */

#define HFC_MULTI_VERSION       "2.03"

#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/pci.h>
#include <linux/delay.h>
#include <linux/mISDNhw.h>
#include <linux/mISDNdsp.h>

/*
  #define IRQCOUNT_DEBUG
  #define IRQ_DEBUG
*/

#include "hfc_multi.h"
#ifdef ECHOPREP
#include "gaintab.h"
#endif

#define MAX_CARDS       8
#define MAX_PORTS       (8 * MAX_CARDS)
#define MAX_FRAGS       (32 * MAX_CARDS)

static LIST_HEAD(HFClist);
static DEFINE_SPINLOCK(HFClock); /* global hfc list lock */

static void ph_state_change(struct dchannel *);

static struct hfc_multi *syncmaster;
static int plxsd_master; /* if we have a master card (yet) */
static DEFINE_SPINLOCK(plx_lock); /* may not acquire other lock inside */

#define TYP_E1          1
#define TYP_4S          4
#define TYP_8S          8

static int poll_timer = 6;      /* default = 128 samples = 16ms */
/* number of POLL_TIMER interrupts for G2 timeout (ca 1s) */
static int nt_t1_count[] = { 3840, 1920, 960, 480, 240, 120, 60, 30  };
#define CLKDEL_TE       0x0f    /* CLKDEL in TE mode */
#define CLKDEL_NT       0x6c    /* CLKDEL in NT mode
                                   (0x60 MUST be included!) */

#define DIP_4S  0x1             /* DIP Switches for Beronet 1S/2S/4S cards */
#define DIP_8S  0x2             /* DIP Switches for Beronet 8S+ cards */
#define DIP_E1  0x3             /* DIP Switches for Beronet E1 cards */

/*
 * module stuff
 */

static uint     type[MAX_CARDS];
static int      pcm[MAX_CARDS];
static uint     dmask[MAX_CARDS];
static uint     bmask[MAX_FRAGS];
static uint     iomode[MAX_CARDS];
static uint     port[MAX_PORTS];
static uint     debug;
static uint     poll;
static int      clock;
static uint     timer;
static uint     clockdelay_te = CLKDEL_TE;
static uint     clockdelay_nt = CLKDEL_NT;
#define HWID_NONE       0
#define HWID_MINIP4     1
#define HWID_MINIP8     2
#define HWID_MINIP16    3
static uint     hwid = HWID_NONE;

static int      HFC_cnt, E1_cnt, bmask_cnt, Port_cnt, PCM_cnt = 99;

MODULE_AUTHOR("Andreas Eversberg");
MODULE_DESCRIPTION("mISDN driver for hfc-4s/hfc-8s/hfc-e1 based cards");
MODULE_LICENSE("GPL");
MODULE_VERSION(HFC_MULTI_VERSION);
module_param(debug, uint, S_IRUGO | S_IWUSR);
module_param(poll, uint, S_IRUGO | S_IWUSR);
module_param(clock, int, S_IRUGO | S_IWUSR);
module_param(timer, uint, S_IRUGO | S_IWUSR);
module_param(clockdelay_te, uint, S_IRUGO | S_IWUSR);
module_param(clockdelay_nt, uint, S_IRUGO | S_IWUSR);
module_param_array(type, uint, NULL, S_IRUGO | S_IWUSR);
module_param_array(pcm, int, NULL, S_IRUGO | S_IWUSR);
module_param_array(dmask, uint, NULL, S_IRUGO | S_IWUSR);
module_param_array(bmask, uint, NULL, S_IRUGO | S_IWUSR);
module_param_array(iomode, uint, NULL, S_IRUGO | S_IWUSR);
module_param_array(port, uint, NULL, S_IRUGO | S_IWUSR);
module_param(hwid, uint, S_IRUGO | S_IWUSR); /* The hardware ID */

#ifdef HFC_REGISTER_DEBUG
#define HFC_outb(hc, reg, val)                                  \
        (hc->HFC_outb(hc, reg, val, __func__, __LINE__))
#define HFC_outb_nodebug(hc, reg, val)                                  \
        (hc->HFC_outb_nodebug(hc, reg, val, __func__, __LINE__))
#define HFC_inb(hc, reg)                                \
        (hc->HFC_inb(hc, reg, __func__, __LINE__))
#define HFC_inb_nodebug(hc, reg)                                \
        (hc->HFC_inb_nodebug(hc, reg, __func__, __LINE__))
#define HFC_inw(hc, reg)                                \
        (hc->HFC_inw(hc, reg, __func__, __LINE__))
#define HFC_inw_nodebug(hc, reg)                                \
        (hc->HFC_inw_nodebug(hc, reg, __func__, __LINE__))
#define HFC_wait(hc)                            \
        (hc->HFC_wait(hc, __func__, __LINE__))
#define HFC_wait_nodebug(hc)                            \
        (hc->HFC_wait_nodebug(hc, __func__, __LINE__))
#else
#define HFC_outb(hc, reg, val)          (hc->HFC_outb(hc, reg, val))
#define HFC_outb_nodebug(hc, reg, val)  (hc->HFC_outb_nodebug(hc, reg, val))
#define HFC_inb(hc, reg)                (hc->HFC_inb(hc, reg))
#define HFC_inb_nodebug(hc, reg)        (hc->HFC_inb_nodebug(hc, reg))
#define HFC_inw(hc, reg)                (hc->HFC_inw(hc, reg))
#define HFC_inw_nodebug(hc, reg)        (hc->HFC_inw_nodebug(hc, reg))
#define HFC_wait(hc)                    (hc->HFC_wait(hc))
#define HFC_wait_nodebug(hc)            (hc->HFC_wait_nodebug(hc))
#endif

#ifdef CONFIG_MISDN_HFCMULTI_8xx
#include "hfc_multi_8xx.h"
#endif

/* HFC_IO_MODE_PCIMEM */
static void
#ifdef HFC_REGISTER_DEBUG
HFC_outb_pcimem(struct hfc_multi *hc, u_char reg, u_char val,
                const char *function, int line)
#else
        HFC_outb_pcimem(struct hfc_multi *hc, u_char reg, u_char val)
#endif
{
        writeb(val, hc->pci_membase + reg);
}
static u_char
#ifdef HFC_REGISTER_DEBUG
HFC_inb_pcimem(struct hfc_multi *hc, u_char reg, const char *function, int line)
#else
        HFC_inb_pcimem(struct hfc_multi *hc, u_char reg)
#endif
{
        return readb(hc->pci_membase + reg);
}
static u_short
#ifdef HFC_REGISTER_DEBUG
HFC_inw_pcimem(struct hfc_multi *hc, u_char reg, const char *function, int line)
#else
        HFC_inw_pcimem(struct hfc_multi *hc, u_char reg)
#endif
{
        return readw(hc->pci_membase + reg);
}
static void
#ifdef HFC_REGISTER_DEBUG
HFC_wait_pcimem(struct hfc_multi *hc, const char *function, int line)
#else
        HFC_wait_pcimem(struct hfc_multi *hc)
#endif
{
        while (readb(hc->pci_membase + R_STATUS) & V_BUSY)
                cpu_relax();
}

/* HFC_IO_MODE_REGIO */
static void
#ifdef HFC_REGISTER_DEBUG
HFC_outb_regio(struct hfc_multi *hc, u_char reg, u_char val,
               const char *function, int line)
#else
        HFC_outb_regio(struct hfc_multi *hc, u_char reg, u_char val)
#endif
{
        outb(reg, hc->pci_iobase + 4);
        outb(val, hc->pci_iobase);
}
static u_char
#ifdef HFC_REGISTER_DEBUG
HFC_inb_regio(struct hfc_multi *hc, u_char reg, const char *function, int line)
#else
        HFC_inb_regio(struct hfc_multi *hc, u_char reg)
#endif
{
        outb(reg, hc->pci_iobase + 4);
        return inb(hc->pci_iobase);
}
static u_short
#ifdef HFC_REGISTER_DEBUG
HFC_inw_regio(struct hfc_multi *hc, u_char reg, const char *function, int line)
#else
        HFC_inw_regio(struct hfc_multi *hc, u_char reg)
#endif
{
        outb(reg, hc->pci_iobase + 4);
        return inw(hc->pci_iobase);
}
static void
#ifdef HFC_REGISTER_DEBUG
HFC_wait_regio(struct hfc_multi *hc, const char *function, int line)
#else
        HFC_wait_regio(struct hfc_multi *hc)
#endif
{
        outb(R_STATUS, hc->pci_iobase + 4);
        while (inb(hc->pci_iobase) & V_BUSY)
                cpu_relax();
}

#ifdef HFC_REGISTER_DEBUG
static void
HFC_outb_debug(struct hfc_multi *hc, u_char reg, u_char val,
               const char *function, int line)
{
        char regname[256] = "", bits[9] = "xxxxxxxx";
        int i;

        i = -1;
        while (hfc_register_names[++i].name) {
                if (hfc_register_names[i].reg == reg)
                        strcat(regname, hfc_register_names[i].name);
        }
        if (regname[0] == '\0')
                strcpy(regname, "register");

        bits[7] = '0' + (!!(val & 1));
        bits[6] = '0' + (!!(val & 2));
        bits[5] = '0' + (!!(val & 4));
        bits[4] = '0' + (!!(val & 8));
        bits[3] = '0' + (!!(val & 16));
        bits[2] = '0' + (!!(val & 32));
        bits[1] = '0' + (!!(val & 64));
        bits[0] = '0' + (!!(val & 128));
        printk(KERN_DEBUG
               "HFC_outb(chip %d, %02x=%s, 0x%02x=%s); in %s() line %d\n",
               hc->id, reg, regname, val, bits, function, line);
        HFC_outb_nodebug(hc, reg, val);
}
static u_char
HFC_inb_debug(struct hfc_multi *hc, u_char reg, const char *function, int line)
{
        char regname[256] = "", bits[9] = "xxxxxxxx";
        u_char val = HFC_inb_nodebug(hc, reg);
        int i;

        i = 0;
        while (hfc_register_names[i++].name)
                ;
        while (hfc_register_names[++i].name) {
                if (hfc_register_names[i].reg == reg)
                        strcat(regname, hfc_register_names[i].name);
        }
        if (regname[0] == '\0')
                strcpy(regname, "register");

        bits[7] = '0' + (!!(val & 1));
        bits[6] = '0' + (!!(val & 2));
        bits[5] = '0' + (!!(val & 4));
        bits[4] = '0' + (!!(val & 8));
        bits[3] = '0' + (!!(val & 16));
        bits[2] = '0' + (!!(val & 32));
        bits[1] = '0' + (!!(val & 64));
        bits[0] = '0' + (!!(val & 128));
        printk(KERN_DEBUG
               "HFC_inb(chip %d, %02x=%s) = 0x%02x=%s; in %s() line %d\n",
               hc->id, reg, regname, val, bits, function, line);
        return val;
}
static u_short
HFC_inw_debug(struct hfc_multi *hc, u_char reg, const char *function, int line)
{
        char regname[256] = "";
        u_short val = HFC_inw_nodebug(hc, reg);
        int i;

        i = 0;
        while (hfc_register_names[i++].name)
                ;
        while (hfc_register_names[++i].name) {
                if (hfc_register_names[i].reg == reg)
                        strcat(regname, hfc_register_names[i].name);
        }
        if (regname[0] == '\0')
                strcpy(regname, "register");

        printk(KERN_DEBUG
               "HFC_inw(chip %d, %02x=%s) = 0x%04x; in %s() line %d\n",
               hc->id, reg, regname, val, function, line);
        return val;
}
static void
HFC_wait_debug(struct hfc_multi *hc, const char *function, int line)
{
        printk(KERN_DEBUG "HFC_wait(chip %d); in %s() line %d\n",
               hc->id, function, line);
        HFC_wait_nodebug(hc);
}
#endif

/* write fifo data (REGIO) */
static void
write_fifo_regio(struct hfc_multi *hc, u_char *data, int len)
{
        outb(A_FIFO_DATA0, (hc->pci_iobase) + 4);
        while (len >> 2) {
                outl(cpu_to_le32(*(u32 *)data), hc->pci_iobase);
                data += 4;
                len -= 4;
        }
        while (len >> 1) {
                outw(cpu_to_le16(*(u16 *)data), hc->pci_iobase);
                data += 2;
                len -= 2;
        }
        while (len) {
                outb(*data, hc->pci_iobase);
                data++;
                len--;
        }
}
/* write fifo data (PCIMEM) */
static void
write_fifo_pcimem(struct hfc_multi *hc, u_char *data, int len)
{
        while (len >> 2) {
                writel(cpu_to_le32(*(u32 *)data),
                       hc->pci_membase + A_FIFO_DATA0);
                data += 4;
                len -= 4;
        }
        while (len >> 1) {
                writew(cpu_to_le16(*(u16 *)data),
                       hc->pci_membase + A_FIFO_DATA0);
                data += 2;
                len -= 2;
        }
        while (len) {
                writeb(*data, hc->pci_membase + A_FIFO_DATA0);
                data++;
                len--;
        }
}

/* read fifo data (REGIO) */
static void
read_fifo_regio(struct hfc_multi *hc, u_char *data, int len)
{
        outb(A_FIFO_DATA0, (hc->pci_iobase) + 4);
        while (len >> 2) {
                *(u32 *)data = le32_to_cpu(inl(hc->pci_iobase));
                data += 4;
                len -= 4;
        }
        while (len >> 1) {
                *(u16 *)data = le16_to_cpu(inw(hc->pci_iobase));
                data += 2;
                len -= 2;
        }
        while (len) {
                *data = inb(hc->pci_iobase);
                data++;
                len--;
        }
}

/* read fifo data (PCIMEM) */
static void
read_fifo_pcimem(struct hfc_multi *hc, u_char *data, int len)
{
        while (len >> 2) {
                *(u32 *)data =
                        le32_to_cpu(readl(hc->pci_membase + A_FIFO_DATA0));
                data += 4;
                len -= 4;
        }
        while (len >> 1) {
                *(u16 *)data =
                        le16_to_cpu(readw(hc->pci_membase + A_FIFO_DATA0));
                data += 2;
                len -= 2;
        }
        while (len) {
                *data = readb(hc->pci_membase + A_FIFO_DATA0);
                data++;
                len--;
        }
}

static void
enable_hwirq(struct hfc_multi *hc)
{
        hc->hw.r_irq_ctrl |= V_GLOB_IRQ_EN;
        HFC_outb(hc, R_IRQ_CTRL, hc->hw.r_irq_ctrl);
}

static void
disable_hwirq(struct hfc_multi *hc)
{
        hc->hw.r_irq_ctrl &= ~((u_char)V_GLOB_IRQ_EN);
        HFC_outb(hc, R_IRQ_CTRL, hc->hw.r_irq_ctrl);
}

#define NUM_EC 2
#define MAX_TDM_CHAN 32


static inline void
enablepcibridge(struct hfc_multi *c)
{
        HFC_outb(c, R_BRG_PCM_CFG, (0x0 << 6) | 0x3); /* was _io before */
}

static inline void
disablepcibridge(struct hfc_multi *c)
{
        HFC_outb(c, R_BRG_PCM_CFG, (0x0 << 6) | 0x2); /* was _io before */
}

static inline unsigned char
readpcibridge(struct hfc_multi *hc, unsigned char address)
{
        unsigned short cipv;
        unsigned char data;

        if (!hc->pci_iobase)
                return 0;

        /* slow down a PCI read access by 1 PCI clock cycle */
        HFC_outb(hc, R_CTRL, 0x4); /*was _io before*/

        if (address == 0)
                cipv = 0x4000;
        else
                cipv = 0x5800;

        /* select local bridge port address by writing to CIP port */
        /* data = HFC_inb(c, cipv); * was _io before */
        outw(cipv, hc->pci_iobase + 4);
        data = inb(hc->pci_iobase);

        /* restore R_CTRL for normal PCI read cycle speed */
        HFC_outb(hc, R_CTRL, 0x0); /* was _io before */

        return data;
}

static inline void
writepcibridge(struct hfc_multi *hc, unsigned char address, unsigned char data)
{
        unsigned short cipv;
        unsigned int datav;

        if (!hc->pci_iobase)
                return;

        if (address == 0)
                cipv = 0x4000;
        else
                cipv = 0x5800;

        /* select local bridge port address by writing to CIP port */
        outw(cipv, hc->pci_iobase + 4);
        /* define a 32 bit dword with 4 identical bytes for write sequence */
        datav = data | ((__u32) data << 8) | ((__u32) data << 16) |
                ((__u32) data << 24);

        /*
         * write this 32 bit dword to the bridge data port
         * this will initiate a write sequence of up to 4 writes to the same
         * address on the local bus interface the number of write accesses
         * is undefined but >=1 and depends on the next PCI transaction
         * during write sequence on the local bus
         */
        outl(datav, hc->pci_iobase);
}

static inline void
cpld_set_reg(struct hfc_multi *hc, unsigned char reg)
{
        /* Do data pin read low byte */
        HFC_outb(hc, R_GPIO_OUT1, reg);
}

static inline void
cpld_write_reg(struct hfc_multi *hc, unsigned char reg, unsigned char val)
{
        cpld_set_reg(hc, reg);

        enablepcibridge(hc);
        writepcibridge(hc, 1, val);
        disablepcibridge(hc);

        return;
}

static inline void
vpm_write_address(struct hfc_multi *hc, unsigned short addr)
{
        cpld_write_reg(hc, 0, 0xff & addr);
        cpld_write_reg(hc, 1, 0x01 & (addr >> 8));
}

static inline unsigned char
vpm_in(struct hfc_multi *c, int which, unsigned short addr)
{
        unsigned char res;

        vpm_write_address(c, addr);

        if (!which)
                cpld_set_reg(c, 2);
        else
                cpld_set_reg(c, 3);

        enablepcibridge(c);
        res = readpcibridge(c, 1);
        disablepcibridge(c);

        cpld_set_reg(c, 0);

        return res;
}

static inline void
vpm_out(struct hfc_multi *c, int which, unsigned short addr,
        unsigned char data)
{
        vpm_write_address(c, addr);

        enablepcibridge(c);

        if (!which)
                cpld_set_reg(c, 2);
        else
                cpld_set_reg(c, 3);

        writepcibridge(c, 1, data);

        cpld_set_reg(c, 0);

        disablepcibridge(c);

        {
                unsigned char regin;
                regin = vpm_in(c, which, addr);
                if (regin != data)
                        printk(KERN_DEBUG "Wrote 0x%x to register 0x%x but got back "
                               "0x%x\n", data, addr, regin);
        }

}


static void
vpm_init(struct hfc_multi *wc)
{
        unsigned char reg;
        unsigned int mask;
        unsigned int i, x, y;
        unsigned int ver;

        for (x = 0; x < NUM_EC; x++) {
                /* Setup GPIO's */
                if (!x) {
                        ver = vpm_in(wc, x, 0x1a0);
                        printk(KERN_DEBUG "VPM: Chip %d: ver %02x\n", x, ver);
                }

                for (y = 0; y < 4; y++) {
                        vpm_out(wc, x, 0x1a8 + y, 0x00); /* GPIO out */
                        vpm_out(wc, x, 0x1ac + y, 0x00); /* GPIO dir */
                        vpm_out(wc, x, 0x1b0 + y, 0x00); /* GPIO sel */
                }

                /* Setup TDM path - sets fsync and tdm_clk as inputs */
                reg = vpm_in(wc, x, 0x1a3); /* misc_con */
                vpm_out(wc, x, 0x1a3, reg & ~2);

                /* Setup Echo length (256 taps) */
                vpm_out(wc, x, 0x022, 1);
                vpm_out(wc, x, 0x023, 0xff);

                /* Setup timeslots */
                vpm_out(wc, x, 0x02f, 0x00);
                mask = 0x02020202 << (x * 4);

                /* Setup the tdm channel masks for all chips */
                for (i = 0; i < 4; i++)
                        vpm_out(wc, x, 0x33 - i, (mask >> (i << 3)) & 0xff);

                /* Setup convergence rate */
                printk(KERN_DEBUG "VPM: A-law mode\n");
                reg = 0x00 | 0x10 | 0x01;
                vpm_out(wc, x, 0x20, reg);
                printk(KERN_DEBUG "VPM reg 0x20 is %x\n", reg);
                /*vpm_out(wc, x, 0x20, (0x00 | 0x08 | 0x20 | 0x10)); */

                vpm_out(wc, x, 0x24, 0x02);
                reg = vpm_in(wc, x, 0x24);
                printk(KERN_DEBUG "NLP Thresh is set to %d (0x%x)\n", reg, reg);

                /* Initialize echo cans */
                for (i = 0; i < MAX_TDM_CHAN; i++) {
                        if (mask & (0x00000001 << i))
                                vpm_out(wc, x, i, 0x00);
                }

                /*
                 * ARM arch at least disallows a udelay of
                 * more than 2ms... it gives a fake "__bad_udelay"
                 * reference at link-time.
                 * long delays in kernel code are pretty sucky anyway
                 * for now work around it using 5 x 2ms instead of 1 x 10ms
                 */

                udelay(2000);
                udelay(2000);
                udelay(2000);
                udelay(2000);
                udelay(2000);

                /* Put in bypass mode */
                for (i = 0; i < MAX_TDM_CHAN; i++) {
                        if (mask & (0x00000001 << i))
                                vpm_out(wc, x, i, 0x01);
                }

                /* Enable bypass */
                for (i = 0; i < MAX_TDM_CHAN; i++) {
                        if (mask & (0x00000001 << i))
                                vpm_out(wc, x, 0x78 + i, 0x01);
                }

        }
}

#ifdef UNUSED
static void
vpm_check(struct hfc_multi *hctmp)
{
        unsigned char gpi2;

        gpi2 = HFC_inb(hctmp, R_GPI_IN2);

        if ((gpi2 & 0x3) != 0x3)
                printk(KERN_DEBUG "Got interrupt 0x%x from VPM!\n", gpi2);
}
#endif /* UNUSED */


/*
 * Interface to enable/disable the HW Echocan
 *
 * these functions are called within a spin_lock_irqsave on
 * the channel instance lock, so we are not disturbed by irqs
 *
 * we can later easily change the interface to make  other
 * things configurable, for now we configure the taps
 *
 */

static void
vpm_echocan_on(struct hfc_multi *hc, int ch, int taps)
{
        unsigned int timeslot;
        unsigned int unit;
        struct bchannel *bch = hc->chan[ch].bch;
#ifdef TXADJ
        int txadj = -4;
        struct sk_buff *skb;
#endif
        if (hc->chan[ch].protocol != ISDN_P_B_RAW)
                return;

        if (!bch)
                return;

#ifdef TXADJ
        skb = _alloc_mISDN_skb(PH_CONTROL_IND, HFC_VOL_CHANGE_TX,
                               sizeof(int), &txadj, GFP_ATOMIC);
        if (skb)
                recv_Bchannel_skb(bch, skb);
#endif

        timeslot = ((ch / 4) * 8) + ((ch % 4) * 4) + 1;
        unit = ch % 4;

        printk(KERN_NOTICE "vpm_echocan_on called taps [%d] on timeslot %d\n",
               taps, timeslot);

        vpm_out(hc, unit, timeslot, 0x7e);
}

static void
vpm_echocan_off(struct hfc_multi *hc, int ch)
{
        unsigned int timeslot;
        unsigned int unit;
        struct bchannel *bch = hc->chan[ch].bch;
#ifdef TXADJ
        int txadj = 0;
        struct sk_buff *skb;
#endif

        if (hc->chan[ch].protocol != ISDN_P_B_RAW)
                return;

        if (!bch)
                return;

#ifdef TXADJ
        skb = _alloc_mISDN_skb(PH_CONTROL_IND, HFC_VOL_CHANGE_TX,
                               sizeof(int), &txadj, GFP_ATOMIC);
        if (skb)
                recv_Bchannel_skb(bch, skb);
#endif

        timeslot = ((ch / 4) * 8) + ((ch % 4) * 4) + 1;
        unit = ch % 4;

        printk(KERN_NOTICE "vpm_echocan_off called on timeslot %d\n",
               timeslot);
        /* FILLME */
        vpm_out(hc, unit, timeslot, 0x01);
}


/*
 * Speech Design resync feature
 * NOTE: This is called sometimes outside interrupt handler.
 * We must lock irqsave, so no other interrupt (other card) will occur!
 * Also multiple interrupts may nest, so must lock each access (lists, card)!
 */
static inline void
hfcmulti_resync(struct hfc_multi *locked, struct hfc_multi *newmaster, int rm)
{
        struct hfc_multi *hc, *next, *pcmmaster = NULL;
        void __iomem *plx_acc_32;
        u_int pv;
        u_long flags;

        spin_lock_irqsave(&HFClock, flags);
        spin_lock(&plx_lock); /* must be locked inside other locks */

        if (debug & DEBUG_HFCMULTI_PLXSD)
                printk(KERN_DEBUG "%s: RESYNC(syncmaster=0x%p)\n",
                       __func__, syncmaster);

        /* select new master */
        if (newmaster) {
                if (debug & DEBUG_HFCMULTI_PLXSD)
                        printk(KERN_DEBUG "using provided controller\n");
        } else {
                list_for_each_entry_safe(hc, next, &HFClist, list) {
                        if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                                if (hc->syncronized) {
                                        newmaster = hc;
                                        break;
                                }
                        }
                }
        }

        /* Disable sync of all cards */
        list_for_each_entry_safe(hc, next, &HFClist, list) {
                if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                        plx_acc_32 = hc->plx_membase + PLX_GPIOC;
                        pv = readl(plx_acc_32);
                        pv &= ~PLX_SYNC_O_EN;
                        writel(pv, plx_acc_32);
                        if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip)) {
                                pcmmaster = hc;
                                if (hc->ctype == HFC_TYPE_E1) {
                                        if (debug & DEBUG_HFCMULTI_PLXSD)
                                                printk(KERN_DEBUG
                                                       "Schedule SYNC_I\n");
                                        hc->e1_resync |= 1; /* get SYNC_I */
                                }
                        }
                }
        }

        if (newmaster) {
                hc = newmaster;
                if (debug & DEBUG_HFCMULTI_PLXSD)
                        printk(KERN_DEBUG "id=%d (0x%p) = synchronized with "
                               "interface.\n", hc->id, hc);
                /* Enable new sync master */
                plx_acc_32 = hc->plx_membase + PLX_GPIOC;
                pv = readl(plx_acc_32);
                pv |= PLX_SYNC_O_EN;
                writel(pv, plx_acc_32);
                /* switch to jatt PLL, if not disabled by RX_SYNC */
                if (hc->ctype == HFC_TYPE_E1
                    && !test_bit(HFC_CHIP_RX_SYNC, &hc->chip)) {
                        if (debug & DEBUG_HFCMULTI_PLXSD)
                                printk(KERN_DEBUG "Schedule jatt PLL\n");
                        hc->e1_resync |= 2; /* switch to jatt */
                }
        } else {
                if (pcmmaster) {
                        hc = pcmmaster;
                        if (debug & DEBUG_HFCMULTI_PLXSD)
                                printk(KERN_DEBUG
                                       "id=%d (0x%p) = PCM master synchronized "
                                       "with QUARTZ\n", hc->id, hc);
                        if (hc->ctype == HFC_TYPE_E1) {
                                /* Use the crystal clock for the PCM
                                   master card */
                                if (debug & DEBUG_HFCMULTI_PLXSD)
                                        printk(KERN_DEBUG
                                               "Schedule QUARTZ for HFC-E1\n");
                                hc->e1_resync |= 4; /* switch quartz */
                        } else {
                                if (debug & DEBUG_HFCMULTI_PLXSD)
                                        printk(KERN_DEBUG
                                               "QUARTZ is automatically "
                                               "enabled by HFC-%dS\n", hc->ctype);
                        }
                        plx_acc_32 = hc->plx_membase + PLX_GPIOC;
                        pv = readl(plx_acc_32);
                        pv |= PLX_SYNC_O_EN;
                        writel(pv, plx_acc_32);
                } else
                        if (!rm)
                                printk(KERN_ERR "%s no pcm master, this MUST "
                                       "not happen!\n", __func__);
        }
        syncmaster = newmaster;

        spin_unlock(&plx_lock);
        spin_unlock_irqrestore(&HFClock, flags);
}

/* This must be called AND hc must be locked irqsave!!! */
static inline void
plxsd_checksync(struct hfc_multi *hc, int rm)
{
        if (hc->syncronized) {
                if (syncmaster == NULL) {
                        if (debug & DEBUG_HFCMULTI_PLXSD)
                                printk(KERN_DEBUG "%s: GOT sync on card %d"
                                       " (id=%d)\n", __func__, hc->id + 1,
                                       hc->id);
                        hfcmulti_resync(hc, hc, rm);
                }
        } else {
                if (syncmaster == hc) {
                        if (debug & DEBUG_HFCMULTI_PLXSD)
                                printk(KERN_DEBUG "%s: LOST sync on card %d"
                                       " (id=%d)\n", __func__, hc->id + 1,
                                       hc->id);
                        hfcmulti_resync(hc, NULL, rm);
                }
        }
}


/*
 * free hardware resources used by driver
 */
static void
release_io_hfcmulti(struct hfc_multi *hc)
{
        void __iomem *plx_acc_32;
        u_int   pv;
        u_long  plx_flags;

        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: entered\n", __func__);

        /* soft reset also masks all interrupts */
        hc->hw.r_cirm |= V_SRES;
        HFC_outb(hc, R_CIRM, hc->hw.r_cirm);
        udelay(1000);
        hc->hw.r_cirm &= ~V_SRES;
        HFC_outb(hc, R_CIRM, hc->hw.r_cirm);
        udelay(1000); /* instead of 'wait' that may cause locking */

        /* release Speech Design card, if PLX was initialized */
        if (test_bit(HFC_CHIP_PLXSD, &hc->chip) && hc->plx_membase) {
                if (debug & DEBUG_HFCMULTI_PLXSD)
                        printk(KERN_DEBUG "%s: release PLXSD card %d\n",
                               __func__, hc->id + 1);
                spin_lock_irqsave(&plx_lock, plx_flags);
                plx_acc_32 = hc->plx_membase + PLX_GPIOC;
                writel(PLX_GPIOC_INIT, plx_acc_32);
                pv = readl(plx_acc_32);
                /* Termination off */
                pv &= ~PLX_TERM_ON;
                /* Disconnect the PCM */
                pv |= PLX_SLAVE_EN_N;
                pv &= ~PLX_MASTER_EN;
                pv &= ~PLX_SYNC_O_EN;
                /* Put the DSP in Reset */
                pv &= ~PLX_DSP_RES_N;
                writel(pv, plx_acc_32);
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: PCM off: PLX_GPIO=%x\n",
                               __func__, pv);
                spin_unlock_irqrestore(&plx_lock, plx_flags);
        }

        /* disable memory mapped ports / io ports */
        test_and_clear_bit(HFC_CHIP_PLXSD, &hc->chip); /* prevent resync */
        if (hc->pci_dev)
                pci_write_config_word(hc->pci_dev, PCI_COMMAND, 0);
        if (hc->pci_membase)
                iounmap(hc->pci_membase);
        if (hc->plx_membase)
                iounmap(hc->plx_membase);
        if (hc->pci_iobase)
                release_region(hc->pci_iobase, 8);
        if (hc->xhfc_membase)
                iounmap((void *)hc->xhfc_membase);

        if (hc->pci_dev) {
                pci_disable_device(hc->pci_dev);
                pci_set_drvdata(hc->pci_dev, NULL);
        }
        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: done\n", __func__);
}

/*
 * function called to reset the HFC chip. A complete software reset of chip
 * and fifos is done. All configuration of the chip is done.
 */

static int
init_chip(struct hfc_multi *hc)
{
        u_long                  flags, val, val2 = 0, rev;
        int                     i, err = 0;
        u_char                  r_conf_en, rval;
        void __iomem            *plx_acc_32;
        u_int                   pv;
        u_long                  plx_flags, hfc_flags;
        int                     plx_count;
        struct hfc_multi        *pos, *next, *plx_last_hc;

        spin_lock_irqsave(&hc->lock, flags);
        /* reset all registers */
        memset(&hc->hw, 0, sizeof(struct hfcm_hw));

        /* revision check */
        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: entered\n", __func__);
        val = HFC_inb(hc, R_CHIP_ID);
        if ((val >> 4) != 0x8 && (val >> 4) != 0xc && (val >> 4) != 0xe &&
            (val >> 1) != 0x31) {
                printk(KERN_INFO "HFC_multi: unknown CHIP_ID:%x\n", (u_int)val);
                err = -EIO;
                goto out;
        }
        rev = HFC_inb(hc, R_CHIP_RV);
        printk(KERN_INFO
               "HFC_multi: detected HFC with chip ID=0x%lx revision=%ld%s\n",
               val, rev, (rev == 0 && (hc->ctype != HFC_TYPE_XHFC)) ?
               " (old FIFO handling)" : "");
        if (hc->ctype != HFC_TYPE_XHFC && rev == 0) {
                test_and_set_bit(HFC_CHIP_REVISION0, &hc->chip);
                printk(KERN_WARNING
                       "HFC_multi: NOTE: Your chip is revision 0, "
                       "ask Cologne Chip for update. Newer chips "
                       "have a better FIFO handling. Old chips "
                       "still work but may have slightly lower "
                       "HDLC transmit performance.\n");
        }
        if (rev > 1) {
                printk(KERN_WARNING "HFC_multi: WARNING: This driver doesn't "
                       "consider chip revision = %ld. The chip / "
                       "bridge may not work.\n", rev);
        }

        /* set s-ram size */
        hc->Flen = 0x10;
        hc->Zmin = 0x80;
        hc->Zlen = 384;
        hc->DTMFbase = 0x1000;
        if (test_bit(HFC_CHIP_EXRAM_128, &hc->chip)) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: changing to 128K external RAM\n",
                               __func__);
                hc->hw.r_ctrl |= V_EXT_RAM;
                hc->hw.r_ram_sz = 1;
                hc->Flen = 0x20;
                hc->Zmin = 0xc0;
                hc->Zlen = 1856;
                hc->DTMFbase = 0x2000;
        }
        if (test_bit(HFC_CHIP_EXRAM_512, &hc->chip)) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: changing to 512K external RAM\n",
                               __func__);
                hc->hw.r_ctrl |= V_EXT_RAM;
                hc->hw.r_ram_sz = 2;
                hc->Flen = 0x20;
                hc->Zmin = 0xc0;
                hc->Zlen = 8000;
                hc->DTMFbase = 0x2000;
        }
        if (hc->ctype == HFC_TYPE_XHFC) {
                hc->Flen = 0x8;
                hc->Zmin = 0x0;
                hc->Zlen = 64;
                hc->DTMFbase = 0x0;
        }
        hc->max_trans = poll << 1;
        if (hc->max_trans > hc->Zlen)
                hc->max_trans = hc->Zlen;

        /* Speech Design PLX bridge */
        if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                if (debug & DEBUG_HFCMULTI_PLXSD)
                        printk(KERN_DEBUG "%s: initializing PLXSD card %d\n",
                               __func__, hc->id + 1);
                spin_lock_irqsave(&plx_lock, plx_flags);
                plx_acc_32 = hc->plx_membase + PLX_GPIOC;
                writel(PLX_GPIOC_INIT, plx_acc_32);
                pv = readl(plx_acc_32);
                /* The first and the last cards are terminating the PCM bus */
                pv |= PLX_TERM_ON; /* hc is currently the last */
                /* Disconnect the PCM */
                pv |= PLX_SLAVE_EN_N;
                pv &= ~PLX_MASTER_EN;
                pv &= ~PLX_SYNC_O_EN;
                /* Put the DSP in Reset */
                pv &= ~PLX_DSP_RES_N;
                writel(pv, plx_acc_32);
                spin_unlock_irqrestore(&plx_lock, plx_flags);
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: slave/term: PLX_GPIO=%x\n",
                               __func__, pv);
                /*
                 * If we are the 3rd PLXSD card or higher, we must turn
                 * termination of last PLXSD card off.
                 */
                spin_lock_irqsave(&HFClock, hfc_flags);
                plx_count = 0;
                plx_last_hc = NULL;
                list_for_each_entry_safe(pos, next, &HFClist, list) {
                        if (test_bit(HFC_CHIP_PLXSD, &pos->chip)) {
                                plx_count++;
                                if (pos != hc)
                                        plx_last_hc = pos;
                        }
                }
                if (plx_count >= 3) {
                        if (debug & DEBUG_HFCMULTI_PLXSD)
                                printk(KERN_DEBUG "%s: card %d is between, so "
                                       "we disable termination\n",
                                       __func__, plx_last_hc->id + 1);
                        spin_lock_irqsave(&plx_lock, plx_flags);
                        plx_acc_32 = plx_last_hc->plx_membase + PLX_GPIOC;
                        pv = readl(plx_acc_32);
                        pv &= ~PLX_TERM_ON;
                        writel(pv, plx_acc_32);
                        spin_unlock_irqrestore(&plx_lock, plx_flags);
                        if (debug & DEBUG_HFCMULTI_INIT)
                                printk(KERN_DEBUG
                                       "%s: term off: PLX_GPIO=%x\n",
                                       __func__, pv);
                }
                spin_unlock_irqrestore(&HFClock, hfc_flags);
                hc->hw.r_pcm_md0 = V_F0_LEN; /* shift clock for DSP */
        }

        if (test_bit(HFC_CHIP_EMBSD, &hc->chip))
                hc->hw.r_pcm_md0 = V_F0_LEN; /* shift clock for DSP */

        /* we only want the real Z2 read-pointer for revision > 0 */
        if (!test_bit(HFC_CHIP_REVISION0, &hc->chip))
                hc->hw.r_ram_sz |= V_FZ_MD;

        /* select pcm mode */
        if (test_bit(HFC_CHIP_PCM_SLAVE, &hc->chip)) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: setting PCM into slave mode\n",
                               __func__);
        } else
                if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip) && !plxsd_master) {
                        if (debug & DEBUG_HFCMULTI_INIT)
                                printk(KERN_DEBUG "%s: setting PCM into master mode\n",
                                       __func__);
                        hc->hw.r_pcm_md0 |= V_PCM_MD;
                } else {
                        if (debug & DEBUG_HFCMULTI_INIT)
                                printk(KERN_DEBUG "%s: performing PCM auto detect\n",
                                       __func__);
                }

        /* soft reset */
        HFC_outb(hc, R_CTRL, hc->hw.r_ctrl);
        if (hc->ctype == HFC_TYPE_XHFC)
                HFC_outb(hc, 0x0C /* R_FIFO_THRES */,
                         0x11 /* 16 Bytes TX/RX */);
        else
                HFC_outb(hc, R_RAM_SZ, hc->hw.r_ram_sz);
        HFC_outb(hc, R_FIFO_MD, 0);
        if (hc->ctype == HFC_TYPE_XHFC)
                hc->hw.r_cirm = V_SRES | V_HFCRES | V_PCMRES | V_STRES;
        else
                hc->hw.r_cirm = V_SRES | V_HFCRES | V_PCMRES | V_STRES
                        | V_RLD_EPR;
        HFC_outb(hc, R_CIRM, hc->hw.r_cirm);
        udelay(100);
        hc->hw.r_cirm = 0;
        HFC_outb(hc, R_CIRM, hc->hw.r_cirm);
        udelay(100);
        if (hc->ctype != HFC_TYPE_XHFC)
                HFC_outb(hc, R_RAM_SZ, hc->hw.r_ram_sz);

        /* Speech Design PLX bridge pcm and sync mode */
        if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                spin_lock_irqsave(&plx_lock, plx_flags);
                plx_acc_32 = hc->plx_membase + PLX_GPIOC;
                pv = readl(plx_acc_32);
                /* Connect PCM */
                if (hc->hw.r_pcm_md0 & V_PCM_MD) {
                        pv |= PLX_MASTER_EN | PLX_SLAVE_EN_N;
                        pv |= PLX_SYNC_O_EN;
                        if (debug & DEBUG_HFCMULTI_INIT)
                                printk(KERN_DEBUG "%s: master: PLX_GPIO=%x\n",
                                       __func__, pv);
                } else {
                        pv &= ~(PLX_MASTER_EN | PLX_SLAVE_EN_N);
                        pv &= ~PLX_SYNC_O_EN;
                        if (debug & DEBUG_HFCMULTI_INIT)
                                printk(KERN_DEBUG "%s: slave: PLX_GPIO=%x\n",
                                       __func__, pv);
                }
                writel(pv, plx_acc_32);
                spin_unlock_irqrestore(&plx_lock, plx_flags);
        }

        /* PCM setup */
        HFC_outb(hc, R_PCM_MD0, hc->hw.r_pcm_md0 | 0x90);
        if (hc->slots == 32)
                HFC_outb(hc, R_PCM_MD1, 0x00);
        if (hc->slots == 64)
                HFC_outb(hc, R_PCM_MD1, 0x10);
        if (hc->slots == 128)
                HFC_outb(hc, R_PCM_MD1, 0x20);
        HFC_outb(hc, R_PCM_MD0, hc->hw.r_pcm_md0 | 0xa0);
        if (test_bit(HFC_CHIP_PLXSD, &hc->chip))
                HFC_outb(hc, R_PCM_MD2, V_SYNC_SRC); /* sync via SYNC_I / O */
        else if (test_bit(HFC_CHIP_EMBSD, &hc->chip))
                HFC_outb(hc, R_PCM_MD2, 0x10); /* V_C2O_EN */
        else
                HFC_outb(hc, R_PCM_MD2, 0x00); /* sync from interface */
        HFC_outb(hc, R_PCM_MD0, hc->hw.r_pcm_md0 | 0x00);
        for (i = 0; i < 256; i++) {
                HFC_outb_nodebug(hc, R_SLOT, i);
                HFC_outb_nodebug(hc, A_SL_CFG, 0);
                if (hc->ctype != HFC_TYPE_XHFC)
                        HFC_outb_nodebug(hc, A_CONF, 0);
                hc->slot_owner[i] = -1;
        }

        /* set clock speed */
        if (test_bit(HFC_CHIP_CLOCK2, &hc->chip)) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG
                               "%s: setting double clock\n", __func__);
                HFC_outb(hc, R_BRG_PCM_CFG, V_PCM_CLK);
        }

        if (test_bit(HFC_CHIP_EMBSD, &hc->chip))
                HFC_outb(hc, 0x02 /* R_CLK_CFG */, 0x40 /* V_CLKO_OFF */);

        /* B410P GPIO */
        if (test_bit(HFC_CHIP_B410P, &hc->chip)) {
                printk(KERN_NOTICE "Setting GPIOs\n");
                HFC_outb(hc, R_GPIO_SEL, 0x30);
                HFC_outb(hc, R_GPIO_EN1, 0x3);
                udelay(1000);
                printk(KERN_NOTICE "calling vpm_init\n");
                vpm_init(hc);
        }

        /* check if R_F0_CNT counts (8 kHz frame count) */
        val = HFC_inb(hc, R_F0_CNTL);
        val += HFC_inb(hc, R_F0_CNTH) << 8;
        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG
                       "HFC_multi F0_CNT %ld after reset\n", val);
        spin_unlock_irqrestore(&hc->lock, flags);
        set_current_state(TASK_UNINTERRUPTIBLE);
        schedule_timeout((HZ / 100) ? : 1); /* Timeout minimum 10ms */
        spin_lock_irqsave(&hc->lock, flags);
        val2 = HFC_inb(hc, R_F0_CNTL);
        val2 += HFC_inb(hc, R_F0_CNTH) << 8;
        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG
                       "HFC_multi F0_CNT %ld after 10 ms (1st try)\n",
                       val2);
        if (val2 >= val + 8) { /* 1 ms */
                /* it counts, so we keep the pcm mode */
                if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip))
                        printk(KERN_INFO "controller is PCM bus MASTER\n");
                else
                        if (test_bit(HFC_CHIP_PCM_SLAVE, &hc->chip))
                                printk(KERN_INFO "controller is PCM bus SLAVE\n");
                        else {
                                test_and_set_bit(HFC_CHIP_PCM_SLAVE, &hc->chip);
                                printk(KERN_INFO "controller is PCM bus SLAVE "
                                       "(auto detected)\n");
                        }
        } else {
                /* does not count */
                if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip)) {
                controller_fail:
                        printk(KERN_ERR "HFC_multi ERROR, getting no 125us "
                               "pulse. Seems that controller fails.\n");
                        err = -EIO;
                        goto out;
                }
                if (test_bit(HFC_CHIP_PCM_SLAVE, &hc->chip)) {
                        printk(KERN_INFO "controller is PCM bus SLAVE "
                               "(ignoring missing PCM clock)\n");
                } else {
                        /* only one pcm master */
                        if (test_bit(HFC_CHIP_PLXSD, &hc->chip)
                            && plxsd_master) {
                                printk(KERN_ERR "HFC_multi ERROR, no clock "
                                       "on another Speech Design card found. "
                                       "Please be sure to connect PCM cable.\n");
                                err = -EIO;
                                goto out;
                        }
                        /* retry with master clock */
                        if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                                spin_lock_irqsave(&plx_lock, plx_flags);
                                plx_acc_32 = hc->plx_membase + PLX_GPIOC;
                                pv = readl(plx_acc_32);
                                pv |= PLX_MASTER_EN | PLX_SLAVE_EN_N;
                                pv |= PLX_SYNC_O_EN;
                                writel(pv, plx_acc_32);
                                spin_unlock_irqrestore(&plx_lock, plx_flags);
                                if (debug & DEBUG_HFCMULTI_INIT)
                                        printk(KERN_DEBUG "%s: master: "
                                               "PLX_GPIO=%x\n", __func__, pv);
                        }
                        hc->hw.r_pcm_md0 |= V_PCM_MD;
                        HFC_outb(hc, R_PCM_MD0, hc->hw.r_pcm_md0 | 0x00);
                        spin_unlock_irqrestore(&hc->lock, flags);
                        set_current_state(TASK_UNINTERRUPTIBLE);
                        schedule_timeout((HZ / 100) ?: 1); /* Timeout min. 10ms */
                        spin_lock_irqsave(&hc->lock, flags);
                        val2 = HFC_inb(hc, R_F0_CNTL);
                        val2 += HFC_inb(hc, R_F0_CNTH) << 8;
                        if (debug & DEBUG_HFCMULTI_INIT)
                                printk(KERN_DEBUG "HFC_multi F0_CNT %ld after "
                                       "10 ms (2nd try)\n", val2);
                        if (val2 >= val + 8) { /* 1 ms */
                                test_and_set_bit(HFC_CHIP_PCM_MASTER,
                                                 &hc->chip);
                                printk(KERN_INFO "controller is PCM bus MASTER "
                                       "(auto detected)\n");
                        } else
                                goto controller_fail;
                }
        }

        /* Release the DSP Reset */
        if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip))
                        plxsd_master = 1;
                spin_lock_irqsave(&plx_lock, plx_flags);
                plx_acc_32 = hc->plx_membase + PLX_GPIOC;
                pv = readl(plx_acc_32);
                pv |=  PLX_DSP_RES_N;
                writel(pv, plx_acc_32);
                spin_unlock_irqrestore(&plx_lock, plx_flags);
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: reset off: PLX_GPIO=%x\n",
                               __func__, pv);
        }

        /* pcm id */
        if (hc->pcm)
                printk(KERN_INFO "controller has given PCM BUS ID %d\n",
                       hc->pcm);
        else {
                if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip)
                    || test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                        PCM_cnt++; /* SD has proprietary bridging */
                }
                hc->pcm = PCM_cnt;
                printk(KERN_INFO "controller has PCM BUS ID %d "
                       "(auto selected)\n", hc->pcm);
        }

        /* set up timer */
        HFC_outb(hc, R_TI_WD, poll_timer);
        hc->hw.r_irqmsk_misc |= V_TI_IRQMSK;

        /* set E1 state machine IRQ */
        if (hc->ctype == HFC_TYPE_E1)
                hc->hw.r_irqmsk_misc |= V_STA_IRQMSK;

        /* set DTMF detection */
        if (test_bit(HFC_CHIP_DTMF, &hc->chip)) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: enabling DTMF detection "
                               "for all B-channel\n", __func__);
                hc->hw.r_dtmf = V_DTMF_EN | V_DTMF_STOP;
                if (test_bit(HFC_CHIP_ULAW, &hc->chip))
                        hc->hw.r_dtmf |= V_ULAW_SEL;
                HFC_outb(hc, R_DTMF_N, 102 - 1);
                hc->hw.r_irqmsk_misc |= V_DTMF_IRQMSK;
        }

        /* conference engine */
        if (test_bit(HFC_CHIP_ULAW, &hc->chip))
                r_conf_en = V_CONF_EN | V_ULAW;
        else
                r_conf_en = V_CONF_EN;
        if (hc->ctype != HFC_TYPE_XHFC)
                HFC_outb(hc, R_CONF_EN, r_conf_en);

        /* setting leds */
        switch (hc->leds) {
        case 1: /* HFC-E1 OEM */
                if (test_bit(HFC_CHIP_WATCHDOG, &hc->chip))
                        HFC_outb(hc, R_GPIO_SEL, 0x32);
                else
                        HFC_outb(hc, R_GPIO_SEL, 0x30);

                HFC_outb(hc, R_GPIO_EN1, 0x0f);
                HFC_outb(hc, R_GPIO_OUT1, 0x00);

                HFC_outb(hc, R_GPIO_EN0, V_GPIO_EN2 | V_GPIO_EN3);
                break;

        case 2: /* HFC-4S OEM */
        case 3:
                HFC_outb(hc, R_GPIO_SEL, 0xf0);
                HFC_outb(hc, R_GPIO_EN1, 0xff);
                HFC_outb(hc, R_GPIO_OUT1, 0x00);
                break;
        }

        if (test_bit(HFC_CHIP_EMBSD, &hc->chip)) {
                hc->hw.r_st_sync = 0x10; /* V_AUTO_SYNCI */
                HFC_outb(hc, R_ST_SYNC, hc->hw.r_st_sync);
        }

        /* set master clock */
        if (hc->masterclk >= 0) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: setting ST master clock "
                               "to port %d (0..%d)\n",
                               __func__, hc->masterclk, hc->ports - 1);
                hc->hw.r_st_sync |= (hc->masterclk | V_AUTO_SYNC);
                HFC_outb(hc, R_ST_SYNC, hc->hw.r_st_sync);
        }



        /* setting misc irq */
        HFC_outb(hc, R_IRQMSK_MISC, hc->hw.r_irqmsk_misc);
        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "r_irqmsk_misc.2: 0x%x\n",
                       hc->hw.r_irqmsk_misc);

        /* RAM access test */
        HFC_outb(hc, R_RAM_ADDR0, 0);
        HFC_outb(hc, R_RAM_ADDR1, 0);
        HFC_outb(hc, R_RAM_ADDR2, 0);
        for (i = 0; i < 256; i++) {
                HFC_outb_nodebug(hc, R_RAM_ADDR0, i);
                HFC_outb_nodebug(hc, R_RAM_DATA, ((i * 3) & 0xff));
        }
        for (i = 0; i < 256; i++) {
                HFC_outb_nodebug(hc, R_RAM_ADDR0, i);
                HFC_inb_nodebug(hc, R_RAM_DATA);
                rval = HFC_inb_nodebug(hc, R_INT_DATA);
                if (rval != ((i * 3) & 0xff)) {
                        printk(KERN_DEBUG
                               "addr:%x val:%x should:%x\n", i, rval,
                               (i * 3) & 0xff);
                        err++;
                }
        }
        if (err) {
                printk(KERN_DEBUG "aborting - %d RAM access errors\n", err);
                err = -EIO;
                goto out;
        }

        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: done\n", __func__);
out:
        spin_unlock_irqrestore(&hc->lock, flags);
        return err;
}


/*
 * control the watchdog
 */
static void
hfcmulti_watchdog(struct hfc_multi *hc)
{
        hc->wdcount++;

        if (hc->wdcount > 10) {
                hc->wdcount = 0;
                hc->wdbyte = hc->wdbyte == V_GPIO_OUT2 ?
                        V_GPIO_OUT3 : V_GPIO_OUT2;

                /* printk("Sending Watchdog Kill %x\n",hc->wdbyte); */
                HFC_outb(hc, R_GPIO_EN0, V_GPIO_EN2 | V_GPIO_EN3);
                HFC_outb(hc, R_GPIO_OUT0, hc->wdbyte);
        }
}



/*
 * output leds
 */
static void
hfcmulti_leds(struct hfc_multi *hc)
{
        unsigned long lled;
        unsigned long leddw;
        int i, state, active, leds;
        struct dchannel *dch;
        int led[4];

        switch (hc->leds) {
        case 1: /* HFC-E1 OEM */
                /* 2 red steady:       LOS
                 * 1 red steady:       L1 not active
                 * 2 green steady:     L1 active
                 * 1st green flashing: activity on TX
                 * 2nd green flashing: activity on RX
                 */
                led[0] = 0;
                led[1] = 0;
                led[2] = 0;
                led[3] = 0;
                dch = hc->chan[hc->dnum[0]].dch;
                if (dch) {
                        if (hc->chan[hc->dnum[0]].los)
                                led[1] = 1;
                        if (hc->e1_state != 1) {
                                led[0] = 1;
                                hc->flash[2] = 0;
                                hc->flash[3] = 0;
                        } else {
                                led[2] = 1;
                                led[3] = 1;
                                if (!hc->flash[2] && hc->activity_tx)
                                        hc->flash[2] = poll;
                                if (!hc->flash[3] && hc->activity_rx)
                                        hc->flash[3] = poll;
                                if (hc->flash[2] && hc->flash[2] < 1024)
                                        led[2] = 0;
                                if (hc->flash[3] && hc->flash[3] < 1024)
                                        led[3] = 0;
                                if (hc->flash[2] >= 2048)
                                        hc->flash[2] = 0;
                                if (hc->flash[3] >= 2048)
                                        hc->flash[3] = 0;
                                if (hc->flash[2])
                                        hc->flash[2] += poll;
                                if (hc->flash[3])
                                        hc->flash[3] += poll;
                        }
                }
                leds = (led[0] | (led[1]<<2) | (led[2]<<1) | (led[3]<<3))^0xF;
                /* leds are inverted */
                if (leds != (int)hc->ledstate) {
                        HFC_outb_nodebug(hc, R_GPIO_OUT1, leds);
                        hc->ledstate = leds;
                }
                break;

        case 2: /* HFC-4S OEM */
                /* red steady:     PH_DEACTIVATE
                 * green steady:   PH_ACTIVATE
                 * green flashing: activity on TX
                 */
                for (i = 0; i < 4; i++) {
                        state = 0;
                        active = -1;
                        dch = hc->chan[(i << 2) | 2].dch;
                        if (dch) {
                                state = dch->state;
                                if (dch->dev.D.protocol == ISDN_P_NT_S0)
                                        active = 3;
                                else
                                        active = 7;
                        }
                        if (state) {
                                if (state == active) {
                                        led[i] = 1; /* led green */
                                        hc->activity_tx |= hc->activity_rx;
                                        if (!hc->flash[i] &&
                                                (hc->activity_tx & (1 << i)))
                                                        hc->flash[i] = poll;
                                        if (hc->flash[i] && hc->flash[i] < 1024)
                                                led[i] = 0; /* led off */
                                        if (hc->flash[i] >= 2048)
                                                hc->flash[i] = 0;
                                        if (hc->flash[i])
                                                hc->flash[i] += poll;
                                } else {
                                        led[i] = 2; /* led red */
                                        hc->flash[i] = 0;
                                }
                        } else
                                led[i] = 0; /* led off */
                }
                if (test_bit(HFC_CHIP_B410P, &hc->chip)) {
                        leds = 0;
                        for (i = 0; i < 4; i++) {
                                if (led[i] == 1) {
                                        /*green*/
                                        leds |= (0x2 << (i * 2));
                                } else if (led[i] == 2) {
                                        /*red*/
                                        leds |= (0x1 << (i * 2));
                                }
                        }
                        if (leds != (int)hc->ledstate) {
                                vpm_out(hc, 0, 0x1a8 + 3, leds);
                                hc->ledstate = leds;
                        }
                } else {
                        leds = ((led[3] > 0) << 0) | ((led[1] > 0) << 1) |
                                ((led[0] > 0) << 2) | ((led[2] > 0) << 3) |
                                ((led[3] & 1) << 4) | ((led[1] & 1) << 5) |
                                ((led[0] & 1) << 6) | ((led[2] & 1) << 7);
                        if (leds != (int)hc->ledstate) {
                                HFC_outb_nodebug(hc, R_GPIO_EN1, leds & 0x0F);
                                HFC_outb_nodebug(hc, R_GPIO_OUT1, leds >> 4);
                                hc->ledstate = leds;
                        }
                }
                break;

        case 3: /* HFC 1S/2S Beronet */
                /* red steady:     PH_DEACTIVATE
                 * green steady:   PH_ACTIVATE
                 * green flashing: activity on TX
                 */
                for (i = 0; i < 2; i++) {
                        state = 0;
                        active = -1;
                        dch = hc->chan[(i << 2) | 2].dch;
                        if (dch) {
                                state = dch->state;
                                if (dch->dev.D.protocol == ISDN_P_NT_S0)
                                        active = 3;
                                else
                                        active = 7;
                        }
                        if (state) {
                                if (state == active) {
                                        led[i] = 1; /* led green */
                                        hc->activity_tx |= hc->activity_rx;
                                        if (!hc->flash[i] &&
                                                (hc->activity_tx & (1 << i)))
                                                        hc->flash[i] = poll;
                                        if (hc->flash[i] < 1024)
                                                led[i] = 0; /* led off */
                                        if (hc->flash[i] >= 2048)
                                                hc->flash[i] = 0;
                                        if (hc->flash[i])
                                                hc->flash[i] += poll;
                                } else {
                                        led[i] = 2; /* led red */
                                        hc->flash[i] = 0;
                                }
                        } else
                                led[i] = 0; /* led off */
                }
                leds = (led[0] > 0) | ((led[1] > 0) << 1) | ((led[0]&1) << 2)
                        | ((led[1]&1) << 3);
                if (leds != (int)hc->ledstate) {
                        HFC_outb_nodebug(hc, R_GPIO_EN1,
                                         ((led[0] > 0) << 2) | ((led[1] > 0) << 3));
                        HFC_outb_nodebug(hc, R_GPIO_OUT1,
                                         ((led[0] & 1) << 2) | ((led[1] & 1) << 3));
                        hc->ledstate = leds;
                }
                break;
        case 8: /* HFC 8S+ Beronet */
                /* off:      PH_DEACTIVATE
                 * steady:   PH_ACTIVATE
                 * flashing: activity on TX
                 */
                lled = 0xff; /* leds off */
                for (i = 0; i < 8; i++) {
                        state = 0;
                        active = -1;
                        dch = hc->chan[(i << 2) | 2].dch;
                        if (dch) {
                                state = dch->state;
                                if (dch->dev.D.protocol == ISDN_P_NT_S0)
                                        active = 3;
                                else
                                        active = 7;
                        }
                        if (state) {
                                if (state == active) {
                                        lled &= ~(1 << i); /* led on */
                                        hc->activity_tx |= hc->activity_rx;
                                        if (!hc->flash[i] &&
                                                (hc->activity_tx & (1 << i)))
                                                        hc->flash[i] = poll;
                                        if (hc->flash[i] < 1024)
                                                lled |= 1 << i; /* led off */
                                        if (hc->flash[i] >= 2048)
                                                hc->flash[i] = 0;
                                        if (hc->flash[i])
                                                hc->flash[i] += poll;
                                } else
                                        hc->flash[i] = 0;
                        }
                }
                leddw = lled << 24 | lled << 16 | lled << 8 | lled;
                if (leddw != hc->ledstate) {
                        /* HFC_outb(hc, R_BRG_PCM_CFG, 1);
                           HFC_outb(c, R_BRG_PCM_CFG, (0x0 << 6) | 0x3); */
                        /* was _io before */
                        HFC_outb_nodebug(hc, R_BRG_PCM_CFG, 1 | V_PCM_CLK);
                        outw(0x4000, hc->pci_iobase + 4);
                        outl(leddw, hc->pci_iobase);
                        HFC_outb_nodebug(hc, R_BRG_PCM_CFG, V_PCM_CLK);
                        hc->ledstate = leddw;
                }
                break;
        }
        hc->activity_tx = 0;
        hc->activity_rx = 0;
}
/*
 * read dtmf coefficients
 */

static void
hfcmulti_dtmf(struct hfc_multi *hc)
{
        s32             *coeff;
        u_int           mantissa;
        int             co, ch;
        struct bchannel *bch = NULL;
        u8              exponent;
        int             dtmf = 0;
        int             addr;
        u16             w_float;
        struct sk_buff  *skb;
        struct mISDNhead *hh;

        if (debug & DEBUG_HFCMULTI_DTMF)
                printk(KERN_DEBUG "%s: dtmf detection irq\n", __func__);
        for (ch = 0; ch <= 31; ch++) {
                /* only process enabled B-channels */
                bch = hc->chan[ch].bch;
                if (!bch)
                        continue;
                if (!hc->created[hc->chan[ch].port])
                        continue;
                if (!test_bit(FLG_TRANSPARENT, &bch->Flags))
                        continue;
                if (debug & DEBUG_HFCMULTI_DTMF)
                        printk(KERN_DEBUG "%s: dtmf channel %d:",
                               __func__, ch);
                coeff = &(hc->chan[ch].coeff[hc->chan[ch].coeff_count * 16]);
                dtmf = 1;
                for (co = 0; co < 8; co++) {
                        /* read W(n-1) coefficient */
                        addr = hc->DTMFbase + ((co << 7) | (ch << 2));
                        HFC_outb_nodebug(hc, R_RAM_ADDR0, addr);
                        HFC_outb_nodebug(hc, R_RAM_ADDR1, addr >> 8);
                        HFC_outb_nodebug(hc, R_RAM_ADDR2, (addr >> 16)
                                         | V_ADDR_INC);
                        w_float = HFC_inb_nodebug(hc, R_RAM_DATA);
                        w_float |= (HFC_inb_nodebug(hc, R_RAM_DATA) << 8);
                        if (debug & DEBUG_HFCMULTI_DTMF)
                                printk(" %04x", w_float);

                        /* decode float (see chip doc) */
                        mantissa = w_float & 0x0fff;
                        if (w_float & 0x8000)
                                mantissa |= 0xfffff000;
                        exponent = (w_float >> 12) & 0x7;
                        if (exponent) {
                                mantissa ^= 0x1000;
                                mantissa <<= (exponent - 1);
                        }

                        /* store coefficient */
                        coeff[co << 1] = mantissa;

                        /* read W(n) coefficient */
                        w_float = HFC_inb_nodebug(hc, R_RAM_DATA);
                        w_float |= (HFC_inb_nodebug(hc, R_RAM_DATA) << 8);
                        if (debug & DEBUG_HFCMULTI_DTMF)
                                printk(" %04x", w_float);

                        /* decode float (see chip doc) */
                        mantissa = w_float & 0x0fff;
                        if (w_float & 0x8000)
                                mantissa |= 0xfffff000;
                        exponent = (w_float >> 12) & 0x7;
                        if (exponent) {
                                mantissa ^= 0x1000;
                                mantissa <<= (exponent - 1);
                        }

                        /* store coefficient */
                        coeff[(co << 1) | 1] = mantissa;
                }
                if (debug & DEBUG_HFCMULTI_DTMF)
                        printk(" DTMF ready %08x %08x %08x %08x "
                               "%08x %08x %08x %08x\n",
                               coeff[0], coeff[1], coeff[2], coeff[3],
                               coeff[4], coeff[5], coeff[6], coeff[7]);
                hc->chan[ch].coeff_count++;
                if (hc->chan[ch].coeff_count == 8) {
                        hc->chan[ch].coeff_count = 0;
                        skb = mI_alloc_skb(512, GFP_ATOMIC);
                        if (!skb) {
                                printk(KERN_DEBUG "%s: No memory for skb\n",
                                       __func__);
                                continue;
                        }
                        hh = mISDN_HEAD_P(skb);
                        hh->prim = PH_CONTROL_IND;
                        hh->id = DTMF_HFC_COEF;
                        skb_put_data(skb, hc->chan[ch].coeff, 512);
                        recv_Bchannel_skb(bch, skb);
                }
        }

        /* restart DTMF processing */
        hc->dtmf = dtmf;
        if (dtmf)
                HFC_outb_nodebug(hc, R_DTMF, hc->hw.r_dtmf | V_RST_DTMF);
}


/*
 * fill fifo as much as possible
 */

static void
hfcmulti_tx(struct hfc_multi *hc, int ch)
{
        int i, ii, temp, tmp_len, len = 0;
        int Zspace, z1, z2; /* must be int for calculation */
        int Fspace, f1, f2;
        u_char *d;
        int *txpending, slot_tx;
        struct  bchannel *bch;
        struct  dchannel *dch;
        struct  sk_buff **sp = NULL;
        int *idxp;

        bch = hc->chan[ch].bch;
        dch = hc->chan[ch].dch;
        if ((!dch) && (!bch))
                return;

        txpending = &hc->chan[ch].txpending;
        slot_tx = hc->chan[ch].slot_tx;
        if (dch) {
                if (!test_bit(FLG_ACTIVE, &dch->Flags))
                        return;
                sp = &dch->tx_skb;
                idxp = &dch->tx_idx;
        } else {
                if (!test_bit(FLG_ACTIVE, &bch->Flags))
                        return;
                sp = &bch->tx_skb;
                idxp = &bch->tx_idx;
        }
        if (*sp)
                len = (*sp)->len;

        if ((!len) && *txpending != 1)
                return; /* no data */

        if (test_bit(HFC_CHIP_B410P, &hc->chip) &&
            (hc->chan[ch].protocol == ISDN_P_B_RAW) &&
            (hc->chan[ch].slot_rx < 0) &&
            (hc->chan[ch].slot_tx < 0))
                HFC_outb_nodebug(hc, R_FIFO, 0x20 | (ch << 1));
        else
                HFC_outb_nodebug(hc, R_FIFO, ch << 1);
        HFC_wait_nodebug(hc);

        if (*txpending == 2) {
                /* reset fifo */
                HFC_outb_nodebug(hc, R_INC_RES_FIFO, V_RES_F);
                HFC_wait_nodebug(hc);
                HFC_outb(hc, A_SUBCH_CFG, 0);
                *txpending = 1;
        }
next_frame:
        if (dch || test_bit(FLG_HDLC, &bch->Flags)) {
                f1 = HFC_inb_nodebug(hc, A_F1);
                f2 = HFC_inb_nodebug(hc, A_F2);
                while (f2 != (temp = HFC_inb_nodebug(hc, A_F2))) {
                        if (debug & DEBUG_HFCMULTI_FIFO)
                                printk(KERN_DEBUG
                                       "%s(card %d): reread f2 because %d!=%d\n",
                                       __func__, hc->id + 1, temp, f2);
                        f2 = temp; /* repeat until F2 is equal */
                }
                Fspace = f2 - f1 - 1;
                if (Fspace < 0)
                        Fspace += hc->Flen;
                /*
                 * Old FIFO handling doesn't give us the current Z2 read
                 * pointer, so we cannot send the next frame before the fifo
                 * is empty. It makes no difference except for a slightly
                 * lower performance.
                 */
                if (test_bit(HFC_CHIP_REVISION0, &hc->chip)) {
                        if (f1 != f2)
                                Fspace = 0;
                        else
                                Fspace = 1;
                }
                /* one frame only for ST D-channels, to allow resending */
                if (hc->ctype != HFC_TYPE_E1 && dch) {
                        if (f1 != f2)
                                Fspace = 0;
                }
                /* F-counter full condition */
                if (Fspace == 0)
                        return;
        }
        z1 = HFC_inw_nodebug(hc, A_Z1) - hc->Zmin;
        z2 = HFC_inw_nodebug(hc, A_Z2) - hc->Zmin;
        while (z2 != (temp = (HFC_inw_nodebug(hc, A_Z2) - hc->Zmin))) {
                if (debug & DEBUG_HFCMULTI_FIFO)
                        printk(KERN_DEBUG "%s(card %d): reread z2 because "
                               "%d!=%d\n", __func__, hc->id + 1, temp, z2);
                z2 = temp; /* repeat unti Z2 is equal */
        }
        hc->chan[ch].Zfill = z1 - z2;
        if (hc->chan[ch].Zfill < 0)
                hc->chan[ch].Zfill += hc->Zlen;
        Zspace = z2 - z1;
        if (Zspace <= 0)
                Zspace += hc->Zlen;
        Zspace -= 4; /* keep not too full, so pointers will not overrun */
        /* fill transparent data only to maximum transparent load (minus 4) */
        if (bch && test_bit(FLG_TRANSPARENT, &bch->Flags))
                Zspace = Zspace - hc->Zlen + hc->max_trans;
        if (Zspace <= 0) /* no space of 4 bytes */
                return;

        /* if no data */
        if (!len) {
                if (z1 == z2) { /* empty */
                        /* if done with FIFO audio data during PCM connection */
                        if (bch && (!test_bit(FLG_HDLC, &bch->Flags)) &&
                            *txpending && slot_tx >= 0) {
                                if (debug & DEBUG_HFCMULTI_MODE)
                                        printk(KERN_DEBUG
                                               "%s: reconnecting PCM due to no "
                                               "more FIFO data: channel %d "
                                               "slot_tx %d\n",
                                               __func__, ch, slot_tx);
                                /* connect slot */
                                if (hc->ctype == HFC_TYPE_XHFC)
                                        HFC_outb(hc, A_CON_HDLC, 0xc0
                                                 | 0x07 << 2 | V_HDLC_TRP | V_IFF);
                                /* Enable FIFO, no interrupt */
                                else
                                        HFC_outb(hc, A_CON_HDLC, 0xc0 | 0x00 |
                                                 V_HDLC_TRP | V_IFF);
                                HFC_outb_nodebug(hc, R_FIFO, ch << 1 | 1);
                                HFC_wait_nodebug(hc);
                                if (hc->ctype == HFC_TYPE_XHFC)
                                        HFC_outb(hc, A_CON_HDLC, 0xc0
                                                 | 0x07 << 2 | V_HDLC_TRP | V_IFF);
                                /* Enable FIFO, no interrupt */
                                else
                                        HFC_outb(hc, A_CON_HDLC, 0xc0 | 0x00 |
                                                 V_HDLC_TRP | V_IFF);
                                HFC_outb_nodebug(hc, R_FIFO, ch << 1);
                                HFC_wait_nodebug(hc);
                        }
                        *txpending = 0;
                }
                return; /* no data */
        }

        /* "fill fifo if empty" feature */
        if (bch && test_bit(FLG_FILLEMPTY, &bch->Flags)
            && !test_bit(FLG_HDLC, &bch->Flags) && z2 == z1) {
                if (debug & DEBUG_HFCMULTI_FILL)
                        printk(KERN_DEBUG "%s: buffer empty, so we have "
                               "underrun\n", __func__);
                /* fill buffer, to prevent future underrun */
                hc->write_fifo(hc, hc->silence_data, poll >> 1);
                Zspace -= (poll >> 1);
        }

        /* if audio data and connected slot */
        if (bch && (!test_bit(FLG_HDLC, &bch->Flags)) && (!*txpending)
            && slot_tx >= 0) {
                if (debug & DEBUG_HFCMULTI_MODE)
                        printk(KERN_DEBUG "%s: disconnecting PCM due to "
                               "FIFO data: channel %d slot_tx %d\n",
                               __func__, ch, slot_tx);
                /* disconnect slot */
                if (hc->ctype == HFC_TYPE_XHFC)
                        HFC_outb(hc, A_CON_HDLC, 0x80
                                 | 0x07 << 2 | V_HDLC_TRP | V_IFF);
                /* Enable FIFO, no interrupt */
                else
                        HFC_outb(hc, A_CON_HDLC, 0x80 | 0x00 |
                                 V_HDLC_TRP | V_IFF);
                HFC_outb_nodebug(hc, R_FIFO, ch << 1 | 1);
                HFC_wait_nodebug(hc);
                if (hc->ctype == HFC_TYPE_XHFC)
                        HFC_outb(hc, A_CON_HDLC, 0x80
                                 | 0x07 << 2 | V_HDLC_TRP | V_IFF);
                /* Enable FIFO, no interrupt */
                else
                        HFC_outb(hc, A_CON_HDLC, 0x80 | 0x00 |
                                 V_HDLC_TRP | V_IFF);
                HFC_outb_nodebug(hc, R_FIFO, ch << 1);
                HFC_wait_nodebug(hc);
        }
        *txpending = 1;

        /* show activity */
        if (dch)
                hc->activity_tx |= 1 << hc->chan[ch].port;

        /* fill fifo to what we have left */
        ii = len;
        if (dch || test_bit(FLG_HDLC, &bch->Flags))
                temp = 1;
        else
                temp = 0;
        i = *idxp;
        d = (*sp)->data + i;
        if (ii - i > Zspace)
                ii = Zspace + i;
        if (debug & DEBUG_HFCMULTI_FIFO)
                printk(KERN_DEBUG "%s(card %d): fifo(%d) has %d bytes space "
                       "left (z1=%04x, z2=%04x) sending %d of %d bytes %s\n",
                       __func__, hc->id + 1, ch, Zspace, z1, z2, ii-i, len-i,
                       temp ? "HDLC" : "TRANS");

        /* Have to prep the audio data */
        hc->write_fifo(hc, d, ii - i);
        hc->chan[ch].Zfill += ii - i;
        *idxp = ii;

        /* if not all data has been written */
        if (ii != len) {
                /* NOTE: fifo is started by the calling function */
                return;
        }

        /* if all data has been written, terminate frame */
        if (dch || test_bit(FLG_HDLC, &bch->Flags)) {
                /* increment f-counter */
                HFC_outb_nodebug(hc, R_INC_RES_FIFO, V_INC_F);
                HFC_wait_nodebug(hc);
        }

        tmp_len = (*sp)->len;
        dev_kfree_skb(*sp);
        /* check for next frame */
        if (bch && get_next_bframe(bch)) {
                len = tmp_len;
                goto next_frame;
        }
        if (dch && get_next_dframe(dch)) {
                len = tmp_len;
                goto next_frame;
        }

        /*
         * now we have no more data, so in case of transparent,
         * we set the last byte in fifo to 'silence' in case we will get
         * no more data at all. this prevents sending an undefined value.
         */
        if (bch && test_bit(FLG_TRANSPARENT, &bch->Flags))
                HFC_outb_nodebug(hc, A_FIFO_DATA0_NOINC, hc->silence);
}


/* NOTE: only called if E1 card is in active state */
static void
hfcmulti_rx(struct hfc_multi *hc, int ch)
{
        int temp;
        int Zsize, z1, z2 = 0; /* = 0, to make GCC happy */
        int f1 = 0, f2 = 0; /* = 0, to make GCC happy */
        int again = 0;
        struct  bchannel *bch;
        struct  dchannel *dch = NULL;
        struct sk_buff  *skb, **sp = NULL;
        int     maxlen;

        bch = hc->chan[ch].bch;
        if (bch) {
                if (!test_bit(FLG_ACTIVE, &bch->Flags))
                        return;
        } else if (hc->chan[ch].dch) {
                dch = hc->chan[ch].dch;
                if (!test_bit(FLG_ACTIVE, &dch->Flags))
                        return;
        } else {
                return;
        }
next_frame:
        /* on first AND before getting next valid frame, R_FIFO must be written
           to. */
        if (test_bit(HFC_CHIP_B410P, &hc->chip) &&
            (hc->chan[ch].protocol == ISDN_P_B_RAW) &&
            (hc->chan[ch].slot_rx < 0) &&
            (hc->chan[ch].slot_tx < 0))
                HFC_outb_nodebug(hc, R_FIFO, 0x20 | (ch << 1) | 1);
        else
                HFC_outb_nodebug(hc, R_FIFO, (ch << 1) | 1);
        HFC_wait_nodebug(hc);

        /* ignore if rx is off BUT change fifo (above) to start pending TX */
        if (hc->chan[ch].rx_off) {
                if (bch)
                        bch->dropcnt += poll; /* not exact but fair enough */
                return;
        }

        if (dch || test_bit(FLG_HDLC, &bch->Flags)) {
                f1 = HFC_inb_nodebug(hc, A_F1);
                while (f1 != (temp = HFC_inb_nodebug(hc, A_F1))) {
                        if (debug & DEBUG_HFCMULTI_FIFO)
                                printk(KERN_DEBUG
                                       "%s(card %d): reread f1 because %d!=%d\n",
                                       __func__, hc->id + 1, temp, f1);
                        f1 = temp; /* repeat until F1 is equal */
                }
                f2 = HFC_inb_nodebug(hc, A_F2);
        }
        z1 = HFC_inw_nodebug(hc, A_Z1) - hc->Zmin;
        while (z1 != (temp = (HFC_inw_nodebug(hc, A_Z1) - hc->Zmin))) {
                if (debug & DEBUG_HFCMULTI_FIFO)
                        printk(KERN_DEBUG "%s(card %d): reread z2 because "
                               "%d!=%d\n", __func__, hc->id + 1, temp, z2);
                z1 = temp; /* repeat until Z1 is equal */
        }
        z2 = HFC_inw_nodebug(hc, A_Z2) - hc->Zmin;
        Zsize = z1 - z2;
        if ((dch || test_bit(FLG_HDLC, &bch->Flags)) && f1 != f2)
                /* complete hdlc frame */
                Zsize++;
        if (Zsize < 0)
                Zsize += hc->Zlen;
        /* if buffer is empty */
        if (Zsize <= 0)
                return;

        if (bch) {
                maxlen = bchannel_get_rxbuf(bch, Zsize);
                if (maxlen < 0) {
                        pr_warn("card%d.B%d: No bufferspace for %d bytes\n",
                                hc->id + 1, bch->nr, Zsize);
                        return;
                }
                sp = &bch->rx_skb;
                maxlen = bch->maxlen;
        } else { /* Dchannel */
                sp = &dch->rx_skb;
                maxlen = dch->maxlen + 3;
                if (*sp == NULL) {
                        *sp = mI_alloc_skb(maxlen, GFP_ATOMIC);
                        if (*sp == NULL) {
                                pr_warn("card%d: No mem for dch rx_skb\n",
                                        hc->id + 1);
                                return;
                        }
                }
        }
        /* show activity */
        if (dch)
                hc->activity_rx |= 1 << hc->chan[ch].port;

        /* empty fifo with what we have */
        if (dch || test_bit(FLG_HDLC, &bch->Flags)) {
                if (debug & DEBUG_HFCMULTI_FIFO)
                        printk(KERN_DEBUG "%s(card %d): fifo(%d) reading %d "
                               "bytes (z1=%04x, z2=%04x) HDLC %s (f1=%d, f2=%d) "
                               "got=%d (again %d)\n", __func__, hc->id + 1, ch,
                               Zsize, z1, z2, (f1 == f2) ? "fragment" : "COMPLETE",
                               f1, f2, Zsize + (*sp)->len, again);
                /* HDLC */
                if ((Zsize + (*sp)->len) > maxlen) {
                        if (debug & DEBUG_HFCMULTI_FIFO)
                                printk(KERN_DEBUG
                                       "%s(card %d): hdlc-frame too large.\n",
                                       __func__, hc->id + 1);
                        skb_trim(*sp, 0);
                        HFC_outb_nodebug(hc, R_INC_RES_FIFO, V_RES_F);
                        HFC_wait_nodebug(hc);
                        return;
                }

                hc->read_fifo(hc, skb_put(*sp, Zsize), Zsize);

                if (f1 != f2) {
                        /* increment Z2,F2-counter */
                        HFC_outb_nodebug(hc, R_INC_RES_FIFO, V_INC_F);
                        HFC_wait_nodebug(hc);
                        /* check size */
                        if ((*sp)->len < 4) {
                                if (debug & DEBUG_HFCMULTI_FIFO)
                                        printk(KERN_DEBUG
                                               "%s(card %d): Frame below minimum "
                                               "size\n", __func__, hc->id + 1);
                                skb_trim(*sp, 0);
                                goto next_frame;
                        }
                        /* there is at least one complete frame, check crc */
                        if ((*sp)->data[(*sp)->len - 1]) {
                                if (debug & DEBUG_HFCMULTI_CRC)
                                        printk(KERN_DEBUG
                                               "%s: CRC-error\n", __func__);
                                skb_trim(*sp, 0);
                                goto next_frame;
                        }
                        skb_trim(*sp, (*sp)->len - 3);
                        if ((*sp)->len < MISDN_COPY_SIZE) {
                                skb = *sp;
                                *sp = mI_alloc_skb(skb->len, GFP_ATOMIC);
                                if (*sp) {
                                        skb_put_data(*sp, skb->data, skb->len);
                                        skb_trim(skb, 0);
                                } else {
                                        printk(KERN_DEBUG "%s: No mem\n",
                                               __func__);
                                        *sp = skb;
                                        skb = NULL;
                                }
                        } else {
                                skb = NULL;
                        }
                        if (debug & DEBUG_HFCMULTI_FIFO) {
                                printk(KERN_DEBUG "%s(card %d):",
                                       __func__, hc->id + 1);
                                temp = 0;
                                while (temp < (*sp)->len)
                                        printk(" %02x", (*sp)->data[temp++]);
                                printk("\n");
                        }
                        if (dch)
                                recv_Dchannel(dch);
                        else
                                recv_Bchannel(bch, MISDN_ID_ANY, false);
                        *sp = skb;
                        again++;
                        goto next_frame;
                }
                /* there is an incomplete frame */
        } else {
                /* transparent */
                hc->read_fifo(hc, skb_put(*sp, Zsize), Zsize);
                if (debug & DEBUG_HFCMULTI_FIFO)
                        printk(KERN_DEBUG
                               "%s(card %d): fifo(%d) reading %d bytes "
                               "(z1=%04x, z2=%04x) TRANS\n",
                               __func__, hc->id + 1, ch, Zsize, z1, z2);
                /* only bch is transparent */
                recv_Bchannel(bch, hc->chan[ch].Zfill, false);
        }
}


/*
 * Interrupt handler
 */
static void
signal_state_up(struct dchannel *dch, int info, char *msg)
{
        struct sk_buff  *skb;
        int             id, data = info;

        if (debug & DEBUG_HFCMULTI_STATE)
                printk(KERN_DEBUG "%s: %s\n", __func__, msg);

        id = TEI_SAPI | (GROUP_TEI << 8); /* manager address */

        skb = _alloc_mISDN_skb(MPH_INFORMATION_IND, id, sizeof(data), &data,
                               GFP_ATOMIC);
        if (!skb)
                return;
        recv_Dchannel_skb(dch, skb);
}

static inline void
handle_timer_irq(struct hfc_multi *hc)
{
        int             ch, temp;
        struct dchannel *dch;
        u_long          flags;

        /* process queued resync jobs */
        if (hc->e1_resync) {
                /* lock, so e1_resync gets not changed */
                spin_lock_irqsave(&HFClock, flags);
                if (hc->e1_resync & 1) {
                        if (debug & DEBUG_HFCMULTI_PLXSD)
                                printk(KERN_DEBUG "Enable SYNC_I\n");
                        HFC_outb(hc, R_SYNC_CTRL, V_EXT_CLK_SYNC);
                        /* disable JATT, if RX_SYNC is set */
                        if (test_bit(HFC_CHIP_RX_SYNC, &hc->chip))
                                HFC_outb(hc, R_SYNC_OUT, V_SYNC_E1_RX);
                }
                if (hc->e1_resync & 2) {
                        if (debug & DEBUG_HFCMULTI_PLXSD)
                                printk(KERN_DEBUG "Enable jatt PLL\n");
                        HFC_outb(hc, R_SYNC_CTRL, V_SYNC_OFFS);
                }
                if (hc->e1_resync & 4) {
                        if (debug & DEBUG_HFCMULTI_PLXSD)
                                printk(KERN_DEBUG
                                       "Enable QUARTZ for HFC-E1\n");
                        /* set jatt to quartz */
                        HFC_outb(hc, R_SYNC_CTRL, V_EXT_CLK_SYNC
                                 | V_JATT_OFF);
                        /* switch to JATT, in case it is not already */
                        HFC_outb(hc, R_SYNC_OUT, 0);
                }
                hc->e1_resync = 0;
                spin_unlock_irqrestore(&HFClock, flags);
        }

        if (hc->ctype != HFC_TYPE_E1 || hc->e1_state == 1)
                for (ch = 0; ch <= 31; ch++) {
                        if (hc->created[hc->chan[ch].port]) {
                                hfcmulti_tx(hc, ch);
                                /* fifo is started when switching to rx-fifo */
                                hfcmulti_rx(hc, ch);
                                if (hc->chan[ch].dch &&
                                    hc->chan[ch].nt_timer > -1) {
                                        dch = hc->chan[ch].dch;
                                        if (!(--hc->chan[ch].nt_timer)) {
                                                schedule_event(dch,
                                                               FLG_PHCHANGE);
                                                if (debug &
                                                    DEBUG_HFCMULTI_STATE)
                                                        printk(KERN_DEBUG
                                                               "%s: nt_timer at "
                                                               "state %x\n",
                                                               __func__,
                                                               dch->state);
                                        }
                                }
                        }
                }
        if (hc->ctype == HFC_TYPE_E1 && hc->created[0]) {
                dch = hc->chan[hc->dnum[0]].dch;
                /* LOS */
                temp = HFC_inb_nodebug(hc, R_SYNC_STA) & V_SIG_LOS;
                hc->chan[hc->dnum[0]].los = temp;
                if (test_bit(HFC_CFG_REPORT_LOS, &hc->chan[hc->dnum[0]].cfg)) {
                        if (!temp && hc->chan[hc->dnum[0]].los)
                                signal_state_up(dch, L1_SIGNAL_LOS_ON,
                                                "LOS detected");
                        if (temp && !hc->chan[hc->dnum[0]].los)
                                signal_state_up(dch, L1_SIGNAL_LOS_OFF,
                                                "LOS gone");
                }
                if (test_bit(HFC_CFG_REPORT_AIS, &hc->chan[hc->dnum[0]].cfg)) {
                        /* AIS */
                        temp = HFC_inb_nodebug(hc, R_SYNC_STA) & V_AIS;
                        if (!temp && hc->chan[hc->dnum[0]].ais)
                                signal_state_up(dch, L1_SIGNAL_AIS_ON,
                                                "AIS detected");
                        if (temp && !hc->chan[hc->dnum[0]].ais)
                                signal_state_up(dch, L1_SIGNAL_AIS_OFF,
                                                "AIS gone");
                        hc->chan[hc->dnum[0]].ais = temp;
                }
                if (test_bit(HFC_CFG_REPORT_SLIP, &hc->chan[hc->dnum[0]].cfg)) {
                        /* SLIP */
                        temp = HFC_inb_nodebug(hc, R_SLIP) & V_FOSLIP_RX;
                        if (!temp && hc->chan[hc->dnum[0]].slip_rx)
                                signal_state_up(dch, L1_SIGNAL_SLIP_RX,
                                                " bit SLIP detected RX");
                        hc->chan[hc->dnum[0]].slip_rx = temp;
                        temp = HFC_inb_nodebug(hc, R_SLIP) & V_FOSLIP_TX;
                        if (!temp && hc->chan[hc->dnum[0]].slip_tx)
                                signal_state_up(dch, L1_SIGNAL_SLIP_TX,
                                                " bit SLIP detected TX");
                        hc->chan[hc->dnum[0]].slip_tx = temp;
                }
                if (test_bit(HFC_CFG_REPORT_RDI, &hc->chan[hc->dnum[0]].cfg)) {
                        /* RDI */
                        temp = HFC_inb_nodebug(hc, R_RX_SL0_0) & V_A;
                        if (!temp && hc->chan[hc->dnum[0]].rdi)
                                signal_state_up(dch, L1_SIGNAL_RDI_ON,
                                                "RDI detected");
                        if (temp && !hc->chan[hc->dnum[0]].rdi)
                                signal_state_up(dch, L1_SIGNAL_RDI_OFF,
                                                "RDI gone");
                        hc->chan[hc->dnum[0]].rdi = temp;
                }
                temp = HFC_inb_nodebug(hc, R_JATT_DIR);
                switch (hc->chan[hc->dnum[0]].sync) {
                case 0:
                        if ((temp & 0x60) == 0x60) {
                                if (debug & DEBUG_HFCMULTI_SYNC)
                                        printk(KERN_DEBUG
                                               "%s: (id=%d) E1 now "
                                               "in clock sync\n",
                                               __func__, hc->id);
                                HFC_outb(hc, R_RX_OFF,
                                    hc->chan[hc->dnum[0]].jitter | V_RX_INIT);
                                HFC_outb(hc, R_TX_OFF,
                                    hc->chan[hc->dnum[0]].jitter | V_RX_INIT);
                                hc->chan[hc->dnum[0]].sync = 1;
                                goto check_framesync;
                        }
                        break;
                case 1:
                        if ((temp & 0x60) != 0x60) {
                                if (debug & DEBUG_HFCMULTI_SYNC)
                                        printk(KERN_DEBUG
                                               "%s: (id=%d) E1 "
                                               "lost clock sync\n",
                                               __func__, hc->id);
                                hc->chan[hc->dnum[0]].sync = 0;
                                break;
                        }
                check_framesync:
                        temp = HFC_inb_nodebug(hc, R_SYNC_STA);
                        if (temp == 0x27) {
                                if (debug & DEBUG_HFCMULTI_SYNC)
                                        printk(KERN_DEBUG
                                               "%s: (id=%d) E1 "
                                               "now in frame sync\n",
                                               __func__, hc->id);
                                hc->chan[hc->dnum[0]].sync = 2;
                        }
                        break;
                case 2:
                        if ((temp & 0x60) != 0x60) {
                                if (debug & DEBUG_HFCMULTI_SYNC)
                                        printk(KERN_DEBUG
                                               "%s: (id=%d) E1 lost "
                                               "clock & frame sync\n",
                                               __func__, hc->id);
                                hc->chan[hc->dnum[0]].sync = 0;
                                break;
                        }
                        temp = HFC_inb_nodebug(hc, R_SYNC_STA);
                        if (temp != 0x27) {
                                if (debug & DEBUG_HFCMULTI_SYNC)
                                        printk(KERN_DEBUG
                                               "%s: (id=%d) E1 "
                                               "lost frame sync\n",
                                               __func__, hc->id);
                                hc->chan[hc->dnum[0]].sync = 1;
                        }
                        break;
                }
        }

        if (test_bit(HFC_CHIP_WATCHDOG, &hc->chip))
                hfcmulti_watchdog(hc);

        if (hc->leds)
                hfcmulti_leds(hc);
}

static void
ph_state_irq(struct hfc_multi *hc, u_char r_irq_statech)
{
        struct dchannel *dch;
        int             ch;
        int             active;
        u_char          st_status, temp;

        /* state machine */
        for (ch = 0; ch <= 31; ch++) {
                if (hc->chan[ch].dch) {
                        dch = hc->chan[ch].dch;
                        if (r_irq_statech & 1) {
                                HFC_outb_nodebug(hc, R_ST_SEL,
                                                 hc->chan[ch].port);
                                /* undocumented: delay after R_ST_SEL */
                                udelay(1);
                                /* undocumented: status changes during read */
                                st_status = HFC_inb_nodebug(hc, A_ST_RD_STATE);
                                while (st_status != (temp =
                                                     HFC_inb_nodebug(hc, A_ST_RD_STATE))) {
                                        if (debug & DEBUG_HFCMULTI_STATE)
                                                printk(KERN_DEBUG "%s: reread "
                                                       "STATE because %d!=%d\n",
                                                       __func__, temp,
                                                       st_status);
                                        st_status = temp; /* repeat */
                                }

                                /* Speech Design TE-sync indication */
                                if (test_bit(HFC_CHIP_PLXSD, &hc->chip) &&
                                    dch->dev.D.protocol == ISDN_P_TE_S0) {
                                        if (st_status & V_FR_SYNC_ST)
                                                hc->syncronized |=
                                                        (1 << hc->chan[ch].port);
                                        else
                                                hc->syncronized &=
                                                        ~(1 << hc->chan[ch].port);
                                }
                                dch->state = st_status & 0x0f;
                                if (dch->dev.D.protocol == ISDN_P_NT_S0)
                                        active = 3;
                                else
                                        active = 7;
                                if (dch->state == active) {
                                        HFC_outb_nodebug(hc, R_FIFO,
                                                         (ch << 1) | 1);
                                        HFC_wait_nodebug(hc);
                                        HFC_outb_nodebug(hc,
                                                         R_INC_RES_FIFO, V_RES_F);
                                        HFC_wait_nodebug(hc);
                                        dch->tx_idx = 0;
                                }
                                schedule_event(dch, FLG_PHCHANGE);
                                if (debug & DEBUG_HFCMULTI_STATE)
                                        printk(KERN_DEBUG
                                               "%s: S/T newstate %x port %d\n",
                                               __func__, dch->state,
                                               hc->chan[ch].port);
                        }
                        r_irq_statech >>= 1;
                }
        }
        if (test_bit(HFC_CHIP_PLXSD, &hc->chip))
                plxsd_checksync(hc, 0);
}

static void
fifo_irq(struct hfc_multi *hc, int block)
{
        int     ch, j;
        struct dchannel *dch;
        struct bchannel *bch;
        u_char r_irq_fifo_bl;

        r_irq_fifo_bl = HFC_inb_nodebug(hc, R_IRQ_FIFO_BL0 + block);
        j = 0;
        while (j < 8) {
                ch = (block << 2) + (j >> 1);
                dch = hc->chan[ch].dch;
                bch = hc->chan[ch].bch;
                if (((!dch) && (!bch)) || (!hc->created[hc->chan[ch].port])) {
                        j += 2;
                        continue;
                }
                if (dch && (r_irq_fifo_bl & (1 << j)) &&
                    test_bit(FLG_ACTIVE, &dch->Flags)) {
                        hfcmulti_tx(hc, ch);
                        /* start fifo */
                        HFC_outb_nodebug(hc, R_FIFO, 0);
                        HFC_wait_nodebug(hc);
                }
                if (bch && (r_irq_fifo_bl & (1 << j)) &&
                    test_bit(FLG_ACTIVE, &bch->Flags)) {
                        hfcmulti_tx(hc, ch);
                        /* start fifo */
                        HFC_outb_nodebug(hc, R_FIFO, 0);
                        HFC_wait_nodebug(hc);
                }
                j++;
                if (dch && (r_irq_fifo_bl & (1 << j)) &&
                    test_bit(FLG_ACTIVE, &dch->Flags)) {
                        hfcmulti_rx(hc, ch);
                }
                if (bch && (r_irq_fifo_bl & (1 << j)) &&
                    test_bit(FLG_ACTIVE, &bch->Flags)) {
                        hfcmulti_rx(hc, ch);
                }
                j++;
        }
}

#ifdef IRQ_DEBUG
int irqsem;
#endif
static irqreturn_t
hfcmulti_interrupt(int intno, void *dev_id)
{
#ifdef IRQCOUNT_DEBUG
        static int iq1 = 0, iq2 = 0, iq3 = 0, iq4 = 0,
                iq5 = 0, iq6 = 0, iqcnt = 0;
#endif
        struct hfc_multi        *hc = dev_id;
        struct dchannel         *dch;
        u_char                  r_irq_statech, status, r_irq_misc, r_irq_oview;
        int                     i;
        void __iomem            *plx_acc;
        u_short                 wval;
        u_char                  e1_syncsta, temp, temp2;
        u_long                  flags;

        if (!hc) {
                printk(KERN_ERR "HFC-multi: Spurious interrupt!\n");
                return IRQ_NONE;
        }

        spin_lock(&hc->lock);

#ifdef IRQ_DEBUG
        if (irqsem)
                printk(KERN_ERR "irq for card %d during irq from "
                       "card %d, this is no bug.\n", hc->id + 1, irqsem);
        irqsem = hc->id + 1;
#endif
#ifdef CONFIG_MISDN_HFCMULTI_8xx
        if (hc->immap->im_cpm.cp_pbdat & hc->pb_irqmsk)
                goto irq_notforus;
#endif
        if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                spin_lock_irqsave(&plx_lock, flags);
                plx_acc = hc->plx_membase + PLX_INTCSR;
                wval = readw(plx_acc);
                spin_unlock_irqrestore(&plx_lock, flags);
                if (!(wval & PLX_INTCSR_LINTI1_STATUS))
                        goto irq_notforus;
        }

        status = HFC_inb_nodebug(hc, R_STATUS);
        r_irq_statech = HFC_inb_nodebug(hc, R_IRQ_STATECH);
#ifdef IRQCOUNT_DEBUG
        if (r_irq_statech)
                iq1++;
        if (status & V_DTMF_STA)
                iq2++;
        if (status & V_LOST_STA)
                iq3++;
        if (status & V_EXT_IRQSTA)
                iq4++;
        if (status & V_MISC_IRQSTA)
                iq5++;
        if (status & V_FR_IRQSTA)
                iq6++;
        if (iqcnt++ > 5000) {
                printk(KERN_ERR "iq1:%x iq2:%x iq3:%x iq4:%x iq5:%x iq6:%x\n",
                       iq1, iq2, iq3, iq4, iq5, iq6);
                iqcnt = 0;
        }
#endif

        if (!r_irq_statech &&
            !(status & (V_DTMF_STA | V_LOST_STA | V_EXT_IRQSTA |
                        V_MISC_IRQSTA | V_FR_IRQSTA))) {
                /* irq is not for us */
                goto irq_notforus;
        }
        hc->irqcnt++;
        if (r_irq_statech) {
                if (hc->ctype != HFC_TYPE_E1)
                        ph_state_irq(hc, r_irq_statech);
        }
        if (status & V_LOST_STA) {
                /* LOST IRQ */
                HFC_outb(hc, R_INC_RES_FIFO, V_RES_LOST); /* clear irq! */
        }
        if (status & V_MISC_IRQSTA) {
                /* misc IRQ */
                r_irq_misc = HFC_inb_nodebug(hc, R_IRQ_MISC);
                r_irq_misc &= hc->hw.r_irqmsk_misc; /* ignore disabled irqs */
                if (r_irq_misc & V_STA_IRQ) {
                        if (hc->ctype == HFC_TYPE_E1) {
                                /* state machine */
                                dch = hc->chan[hc->dnum[0]].dch;
                                e1_syncsta = HFC_inb_nodebug(hc, R_SYNC_STA);
                                if (test_bit(HFC_CHIP_PLXSD, &hc->chip)
                                    && hc->e1_getclock) {
                                        if (e1_syncsta & V_FR_SYNC_E1)
                                                hc->syncronized = 1;
                                        else
                                                hc->syncronized = 0;
                                }
                                /* undocumented: status changes during read */
                                temp = HFC_inb_nodebug(hc, R_E1_RD_STA);
                                while (temp != (temp2 =
                                                      HFC_inb_nodebug(hc, R_E1_RD_STA))) {
                                        if (debug & DEBUG_HFCMULTI_STATE)
                                                printk(KERN_DEBUG "%s: reread "
                                                       "STATE because %d!=%d\n",
                                                    __func__, temp, temp2);
                                        temp = temp2; /* repeat */
                                }
                                /* broadcast state change to all fragments */
                                if (debug & DEBUG_HFCMULTI_STATE)
                                        printk(KERN_DEBUG
                                               "%s: E1 (id=%d) newstate %x\n",
                                            __func__, hc->id, temp & 0x7);
                                for (i = 0; i < hc->ports; i++) {
                                        dch = hc->chan[hc->dnum[i]].dch;
                                        dch->state = temp & 0x7;
                                        schedule_event(dch, FLG_PHCHANGE);
                                }

                                if (test_bit(HFC_CHIP_PLXSD, &hc->chip))
                                        plxsd_checksync(hc, 0);
                        }
                }
                if (r_irq_misc & V_TI_IRQ) {
                        if (hc->iclock_on)
                                mISDN_clock_update(hc->iclock, poll, NULL);
                        handle_timer_irq(hc);
                }

                if (r_irq_misc & V_DTMF_IRQ)
                        hfcmulti_dtmf(hc);

                if (r_irq_misc & V_IRQ_PROC) {
                        static int irq_proc_cnt;
                        if (!irq_proc_cnt++)
                                printk(KERN_DEBUG "%s: got V_IRQ_PROC -"
                                       " this should not happen\n", __func__);
                }

        }
        if (status & V_FR_IRQSTA) {
                /* FIFO IRQ */
                r_irq_oview = HFC_inb_nodebug(hc, R_IRQ_OVIEW);
                for (i = 0; i < 8; i++) {
                        if (r_irq_oview & (1 << i))
                                fifo_irq(hc, i);
                }
        }

#ifdef IRQ_DEBUG
        irqsem = 0;
#endif
        spin_unlock(&hc->lock);
        return IRQ_HANDLED;

irq_notforus:
#ifdef IRQ_DEBUG
        irqsem = 0;
#endif
        spin_unlock(&hc->lock);
        return IRQ_NONE;
}


/*
 * timer callback for D-chan busy resolution. Currently no function
 */

static void
hfcmulti_dbusy_timer(struct timer_list *t)
{
}


/*
 * activate/deactivate hardware for selected channels and mode
 *
 * configure B-channel with the given protocol
 * ch eqals to the HFC-channel (0-31)
 * ch is the number of channel (0-4,4-7,8-11,12-15,16-19,20-23,24-27,28-31
 * for S/T, 1-31 for E1)
 * the hdlc interrupts will be set/unset
 */
static int
mode_hfcmulti(struct hfc_multi *hc, int ch, int protocol, int slot_tx,
              int bank_tx, int slot_rx, int bank_rx)
{
        int flow_tx = 0, flow_rx = 0, routing = 0;
        int oslot_tx, oslot_rx;
        int conf;

        if (ch < 0 || ch > 31)
                return -EINVAL;
        oslot_tx = hc->chan[ch].slot_tx;
        oslot_rx = hc->chan[ch].slot_rx;
        conf = hc->chan[ch].conf;

        if (debug & DEBUG_HFCMULTI_MODE)
                printk(KERN_DEBUG
                       "%s: card %d channel %d protocol %x slot old=%d new=%d "
                       "bank new=%d (TX) slot old=%d new=%d bank new=%d (RX)\n",
                       __func__, hc->id, ch, protocol, oslot_tx, slot_tx,
                       bank_tx, oslot_rx, slot_rx, bank_rx);

        if (oslot_tx >= 0 && slot_tx != oslot_tx) {
                /* remove from slot */
                if (debug & DEBUG_HFCMULTI_MODE)
                        printk(KERN_DEBUG "%s: remove from slot %d (TX)\n",
                               __func__, oslot_tx);
                if (hc->slot_owner[oslot_tx << 1] == ch) {
                        HFC_outb(hc, R_SLOT, oslot_tx << 1);
                        HFC_outb(hc, A_SL_CFG, 0);
                        if (hc->ctype != HFC_TYPE_XHFC)
                                HFC_outb(hc, A_CONF, 0);
                        hc->slot_owner[oslot_tx << 1] = -1;
                } else {
                        if (debug & DEBUG_HFCMULTI_MODE)
                                printk(KERN_DEBUG
                                       "%s: we are not owner of this tx slot "
                                       "anymore, channel %d is.\n",
                                       __func__, hc->slot_owner[oslot_tx << 1]);
                }
        }

        if (oslot_rx >= 0 && slot_rx != oslot_rx) {
                /* remove from slot */
                if (debug & DEBUG_HFCMULTI_MODE)
                        printk(KERN_DEBUG
                               "%s: remove from slot %d (RX)\n",
                               __func__, oslot_rx);
                if (hc->slot_owner[(oslot_rx << 1) | 1] == ch) {
                        HFC_outb(hc, R_SLOT, (oslot_rx << 1) | V_SL_DIR);
                        HFC_outb(hc, A_SL_CFG, 0);
                        hc->slot_owner[(oslot_rx << 1) | 1] = -1;
                } else {
                        if (debug & DEBUG_HFCMULTI_MODE)
                                printk(KERN_DEBUG
                                       "%s: we are not owner of this rx slot "
                                       "anymore, channel %d is.\n",
                                       __func__,
                                       hc->slot_owner[(oslot_rx << 1) | 1]);
                }
        }

        if (slot_tx < 0) {
                flow_tx = 0x80; /* FIFO->ST */
                /* disable pcm slot */
                hc->chan[ch].slot_tx = -1;
                hc->chan[ch].bank_tx = 0;
        } else {
                /* set pcm slot */
                if (hc->chan[ch].txpending)
                        flow_tx = 0x80; /* FIFO->ST */
                else
                        flow_tx = 0xc0; /* PCM->ST */
                /* put on slot */
                routing = bank_tx ? 0xc0 : 0x80;
                if (conf >= 0 || bank_tx > 1)
                        routing = 0x40; /* loop */
                if (debug & DEBUG_HFCMULTI_MODE)
                        printk(KERN_DEBUG "%s: put channel %d to slot %d bank"
                               " %d flow %02x routing %02x conf %d (TX)\n",
                               __func__, ch, slot_tx, bank_tx,
                               flow_tx, routing, conf);
                HFC_outb(hc, R_SLOT, slot_tx << 1);
                HFC_outb(hc, A_SL_CFG, (ch << 1) | routing);
                if (hc->ctype != HFC_TYPE_XHFC)
                        HFC_outb(hc, A_CONF,
                                 (conf < 0) ? 0 : (conf | V_CONF_SL));
                hc->slot_owner[slot_tx << 1] = ch;
                hc->chan[ch].slot_tx = slot_tx;
                hc->chan[ch].bank_tx = bank_tx;
        }
        if (slot_rx < 0) {
                /* disable pcm slot */
                flow_rx = 0x80; /* ST->FIFO */
                hc->chan[ch].slot_rx = -1;
                hc->chan[ch].bank_rx = 0;
        } else {
                /* set pcm slot */
                if (hc->chan[ch].txpending)
                        flow_rx = 0x80; /* ST->FIFO */
                else
                        flow_rx = 0xc0; /* ST->(FIFO,PCM) */
                /* put on slot */
                routing = bank_rx ? 0x80 : 0xc0; /* reversed */
                if (conf >= 0 || bank_rx > 1)
                        routing = 0x40; /* loop */
                if (debug & DEBUG_HFCMULTI_MODE)
                        printk(KERN_DEBUG "%s: put channel %d to slot %d bank"
                               " %d flow %02x routing %02x conf %d (RX)\n",
                               __func__, ch, slot_rx, bank_rx,
                               flow_rx, routing, conf);
                HFC_outb(hc, R_SLOT, (slot_rx << 1) | V_SL_DIR);
                HFC_outb(hc, A_SL_CFG, (ch << 1) | V_CH_DIR | routing);
                hc->slot_owner[(slot_rx << 1) | 1] = ch;
                hc->chan[ch].slot_rx = slot_rx;
                hc->chan[ch].bank_rx = bank_rx;
        }

        switch (protocol) {
        case (ISDN_P_NONE):
                /* disable TX fifo */
                HFC_outb(hc, R_FIFO, ch << 1);
                HFC_wait(hc);
                HFC_outb(hc, A_CON_HDLC, flow_tx | 0x00 | V_IFF);
                HFC_outb(hc, A_SUBCH_CFG, 0);
                HFC_outb(hc, A_IRQ_MSK, 0);
                HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
                HFC_wait(hc);
                /* disable RX fifo */
                HFC_outb(hc, R_FIFO, (ch << 1) | 1);
                HFC_wait(hc);
                HFC_outb(hc, A_CON_HDLC, flow_rx | 0x00);
                HFC_outb(hc, A_SUBCH_CFG, 0);
                HFC_outb(hc, A_IRQ_MSK, 0);
                HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
                HFC_wait(hc);
                if (hc->chan[ch].bch && hc->ctype != HFC_TYPE_E1) {
                        hc->hw.a_st_ctrl0[hc->chan[ch].port] &=
                                ((ch & 0x3) == 0) ? ~V_B1_EN : ~V_B2_EN;
                        HFC_outb(hc, R_ST_SEL, hc->chan[ch].port);
                        /* undocumented: delay after R_ST_SEL */
                        udelay(1);
                        HFC_outb(hc, A_ST_CTRL0,
                                 hc->hw.a_st_ctrl0[hc->chan[ch].port]);
                }
                if (hc->chan[ch].bch) {
                        test_and_clear_bit(FLG_HDLC, &hc->chan[ch].bch->Flags);
                        test_and_clear_bit(FLG_TRANSPARENT,
                                           &hc->chan[ch].bch->Flags);
                }
                break;
        case (ISDN_P_B_RAW): /* B-channel */

                if (test_bit(HFC_CHIP_B410P, &hc->chip) &&
                    (hc->chan[ch].slot_rx < 0) &&
                    (hc->chan[ch].slot_tx < 0)) {

                        printk(KERN_DEBUG
                               "Setting B-channel %d to echo cancelable "
                               "state on PCM slot %d\n", ch,
                               ((ch / 4) * 8) + ((ch % 4) * 4) + 1);
                        printk(KERN_DEBUG
                               "Enabling pass through for channel\n");
                        vpm_out(hc, ch, ((ch / 4) * 8) +
                                ((ch % 4) * 4) + 1, 0x01);
                        /* rx path */
                        /* S/T -> PCM */
                        HFC_outb(hc, R_FIFO, (ch << 1));
                        HFC_wait(hc);
                        HFC_outb(hc, A_CON_HDLC, 0xc0 | V_HDLC_TRP | V_IFF);
                        HFC_outb(hc, R_SLOT, (((ch / 4) * 8) +
                                              ((ch % 4) * 4) + 1) << 1);
                        HFC_outb(hc, A_SL_CFG, 0x80 | (ch << 1));

                        /* PCM -> FIFO */
                        HFC_outb(hc, R_FIFO, 0x20 | (ch << 1) | 1);
                        HFC_wait(hc);
                        HFC_outb(hc, A_CON_HDLC, 0x20 | V_HDLC_TRP | V_IFF);
                        HFC_outb(hc, A_SUBCH_CFG, 0);
                        HFC_outb(hc, A_IRQ_MSK, 0);
                        if (hc->chan[ch].protocol != protocol) {
                                HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
                                HFC_wait(hc);
                        }
                        HFC_outb(hc, R_SLOT, ((((ch / 4) * 8) +
                                               ((ch % 4) * 4) + 1) << 1) | 1);
                        HFC_outb(hc, A_SL_CFG, 0x80 | 0x20 | (ch << 1) | 1);

                        /* tx path */
                        /* PCM -> S/T */
                        HFC_outb(hc, R_FIFO, (ch << 1) | 1);
                        HFC_wait(hc);
                        HFC_outb(hc, A_CON_HDLC, 0xc0 | V_HDLC_TRP | V_IFF);
                        HFC_outb(hc, R_SLOT, ((((ch / 4) * 8) +
                                               ((ch % 4) * 4)) << 1) | 1);
                        HFC_outb(hc, A_SL_CFG, 0x80 | 0x40 | (ch << 1) | 1);

                        /* FIFO -> PCM */
                        HFC_outb(hc, R_FIFO, 0x20 | (ch << 1));
                        HFC_wait(hc);
                        HFC_outb(hc, A_CON_HDLC, 0x20 | V_HDLC_TRP | V_IFF);
                        HFC_outb(hc, A_SUBCH_CFG, 0);
                        HFC_outb(hc, A_IRQ_MSK, 0);
                        if (hc->chan[ch].protocol != protocol) {
                                HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
                                HFC_wait(hc);
                        }
                        /* tx silence */
                        HFC_outb_nodebug(hc, A_FIFO_DATA0_NOINC, hc->silence);
                        HFC_outb(hc, R_SLOT, (((ch / 4) * 8) +
                                              ((ch % 4) * 4)) << 1);
                        HFC_outb(hc, A_SL_CFG, 0x80 | 0x20 | (ch << 1));
                } else {
                        /* enable TX fifo */
                        HFC_outb(hc, R_FIFO, ch << 1);
                        HFC_wait(hc);
                        if (hc->ctype == HFC_TYPE_XHFC)
                                HFC_outb(hc, A_CON_HDLC, flow_tx | 0x07 << 2 |
                                         V_HDLC_TRP | V_IFF);
                        /* Enable FIFO, no interrupt */
                        else
                                HFC_outb(hc, A_CON_HDLC, flow_tx | 0x00 |
                                         V_HDLC_TRP | V_IFF);
                        HFC_outb(hc, A_SUBCH_CFG, 0);
                        HFC_outb(hc, A_IRQ_MSK, 0);
                        if (hc->chan[ch].protocol != protocol) {
                                HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
                                HFC_wait(hc);
                        }
                        /* tx silence */
                        HFC_outb_nodebug(hc, A_FIFO_DATA0_NOINC, hc->silence);
                        /* enable RX fifo */
                        HFC_outb(hc, R_FIFO, (ch << 1) | 1);
                        HFC_wait(hc);
                        if (hc->ctype == HFC_TYPE_XHFC)
                                HFC_outb(hc, A_CON_HDLC, flow_rx | 0x07 << 2 |
                                         V_HDLC_TRP);
                        /* Enable FIFO, no interrupt*/
                        else
                                HFC_outb(hc, A_CON_HDLC, flow_rx | 0x00 |
                                         V_HDLC_TRP);
                        HFC_outb(hc, A_SUBCH_CFG, 0);
                        HFC_outb(hc, A_IRQ_MSK, 0);
                        if (hc->chan[ch].protocol != protocol) {
                                HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
                                HFC_wait(hc);
                        }
                }
                if (hc->ctype != HFC_TYPE_E1) {
                        hc->hw.a_st_ctrl0[hc->chan[ch].port] |=
                                ((ch & 0x3) == 0) ? V_B1_EN : V_B2_EN;
                        HFC_outb(hc, R_ST_SEL, hc->chan[ch].port);
                        /* undocumented: delay after R_ST_SEL */
                        udelay(1);
                        HFC_outb(hc, A_ST_CTRL0,
                                 hc->hw.a_st_ctrl0[hc->chan[ch].port]);
                }
                if (hc->chan[ch].bch)
                        test_and_set_bit(FLG_TRANSPARENT,
                                         &hc->chan[ch].bch->Flags);
                break;
        case (ISDN_P_B_HDLC): /* B-channel */
        case (ISDN_P_TE_S0): /* D-channel */
        case (ISDN_P_NT_S0):
        case (ISDN_P_TE_E1):
        case (ISDN_P_NT_E1):
                /* enable TX fifo */
                HFC_outb(hc, R_FIFO, ch << 1);
                HFC_wait(hc);
                if (hc->ctype == HFC_TYPE_E1 || hc->chan[ch].bch) {
                        /* E1 or B-channel */
                        HFC_outb(hc, A_CON_HDLC, flow_tx | 0x04);
                        HFC_outb(hc, A_SUBCH_CFG, 0);
                } else {
                        /* D-Channel without HDLC fill flags */
                        HFC_outb(hc, A_CON_HDLC, flow_tx | 0x04 | V_IFF);
                        HFC_outb(hc, A_SUBCH_CFG, 2);
                }
                HFC_outb(hc, A_IRQ_MSK, V_IRQ);
                HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
                HFC_wait(hc);
                /* enable RX fifo */
                HFC_outb(hc, R_FIFO, (ch << 1) | 1);
                HFC_wait(hc);
                HFC_outb(hc, A_CON_HDLC, flow_rx | 0x04);
                if (hc->ctype == HFC_TYPE_E1 || hc->chan[ch].bch)
                        HFC_outb(hc, A_SUBCH_CFG, 0); /* full 8 bits */
                else
                        HFC_outb(hc, A_SUBCH_CFG, 2); /* 2 bits dchannel */
                HFC_outb(hc, A_IRQ_MSK, V_IRQ);
                HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
                HFC_wait(hc);
                if (hc->chan[ch].bch) {
                        test_and_set_bit(FLG_HDLC, &hc->chan[ch].bch->Flags);
                        if (hc->ctype != HFC_TYPE_E1) {
                                hc->hw.a_st_ctrl0[hc->chan[ch].port] |=
                                        ((ch & 0x3) == 0) ? V_B1_EN : V_B2_EN;
                                HFC_outb(hc, R_ST_SEL, hc->chan[ch].port);
                                /* undocumented: delay after R_ST_SEL */
                                udelay(1);
                                HFC_outb(hc, A_ST_CTRL0,
                                         hc->hw.a_st_ctrl0[hc->chan[ch].port]);
                        }
                }
                break;
        default:
                printk(KERN_DEBUG "%s: protocol not known %x\n",
                       __func__, protocol);
                hc->chan[ch].protocol = ISDN_P_NONE;
                return -ENOPROTOOPT;
        }
        hc->chan[ch].protocol = protocol;
        return 0;
}


/*
 * connect/disconnect PCM
 */

static void
hfcmulti_pcm(struct hfc_multi *hc, int ch, int slot_tx, int bank_tx,
             int slot_rx, int bank_rx)
{
        if (slot_tx < 0 || slot_rx < 0 || bank_tx < 0 || bank_rx < 0) {
                /* disable PCM */
                mode_hfcmulti(hc, ch, hc->chan[ch].protocol, -1, 0, -1, 0);
                return;
        }

        /* enable pcm */
        mode_hfcmulti(hc, ch, hc->chan[ch].protocol, slot_tx, bank_tx,
                      slot_rx, bank_rx);
}

/*
 * set/disable conference
 */

static void
hfcmulti_conf(struct hfc_multi *hc, int ch, int num)
{
        if (num >= 0 && num <= 7)
                hc->chan[ch].conf = num;
        else
                hc->chan[ch].conf = -1;
        mode_hfcmulti(hc, ch, hc->chan[ch].protocol, hc->chan[ch].slot_tx,
                      hc->chan[ch].bank_tx, hc->chan[ch].slot_rx,
                      hc->chan[ch].bank_rx);
}


/*
 * set/disable sample loop
 */

/* NOTE: this function is experimental and therefore disabled */

/*
 * Layer 1 callback function
 */
static int
hfcm_l1callback(struct dchannel *dch, u_int cmd)
{
        struct hfc_multi        *hc = dch->hw;
        struct sk_buff_head     free_queue;
        u_long  flags;

        switch (cmd) {
        case INFO3_P8:
        case INFO3_P10:
                break;
        case HW_RESET_REQ:
                /* start activation */
                spin_lock_irqsave(&hc->lock, flags);
                if (hc->ctype == HFC_TYPE_E1) {
                        if (debug & DEBUG_HFCMULTI_MSG)
                                printk(KERN_DEBUG
                                       "%s: HW_RESET_REQ no BRI\n",
                                       __func__);
                } else {
                        HFC_outb(hc, R_ST_SEL, hc->chan[dch->slot].port);
                        /* undocumented: delay after R_ST_SEL */
                        udelay(1);
                        HFC_outb(hc, A_ST_WR_STATE, V_ST_LD_STA | 3); /* F3 */
                        udelay(6); /* wait at least 5,21us */
                        HFC_outb(hc, A_ST_WR_STATE, 3);
                        HFC_outb(hc, A_ST_WR_STATE, 3 | (V_ST_ACT * 3));
                        /* activate */
                }
                spin_unlock_irqrestore(&hc->lock, flags);
                l1_event(dch->l1, HW_POWERUP_IND);
                break;
        case HW_DEACT_REQ:
                __skb_queue_head_init(&free_queue);
                /* start deactivation */
                spin_lock_irqsave(&hc->lock, flags);
                if (hc->ctype == HFC_TYPE_E1) {
                        if (debug & DEBUG_HFCMULTI_MSG)
                                printk(KERN_DEBUG
                                       "%s: HW_DEACT_REQ no BRI\n",
                                       __func__);
                } else {
                        HFC_outb(hc, R_ST_SEL, hc->chan[dch->slot].port);
                        /* undocumented: delay after R_ST_SEL */
                        udelay(1);
                        HFC_outb(hc, A_ST_WR_STATE, V_ST_ACT * 2);
                        /* deactivate */
                        if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                                hc->syncronized &=
                                        ~(1 << hc->chan[dch->slot].port);
                                plxsd_checksync(hc, 0);
                        }
                }
                skb_queue_splice_init(&dch->squeue, &free_queue);
                if (dch->tx_skb) {
                        __skb_queue_tail(&free_queue, dch->tx_skb);
                        dch->tx_skb = NULL;
                }
                dch->tx_idx = 0;
                if (dch->rx_skb) {
                        __skb_queue_tail(&free_queue, dch->rx_skb);
                        dch->rx_skb = NULL;
                }
                test_and_clear_bit(FLG_TX_BUSY, &dch->Flags);
                if (test_and_clear_bit(FLG_BUSY_TIMER, &dch->Flags))
                        timer_delete(&dch->timer);
                spin_unlock_irqrestore(&hc->lock, flags);
                __skb_queue_purge(&free_queue);
                break;
        case HW_POWERUP_REQ:
                spin_lock_irqsave(&hc->lock, flags);
                if (hc->ctype == HFC_TYPE_E1) {
                        if (debug & DEBUG_HFCMULTI_MSG)
                                printk(KERN_DEBUG
                                       "%s: HW_POWERUP_REQ no BRI\n",
                                       __func__);
                } else {
                        HFC_outb(hc, R_ST_SEL, hc->chan[dch->slot].port);
                        /* undocumented: delay after R_ST_SEL */
                        udelay(1);
                        HFC_outb(hc, A_ST_WR_STATE, 3 | 0x10); /* activate */
                        udelay(6); /* wait at least 5,21us */
                        HFC_outb(hc, A_ST_WR_STATE, 3); /* activate */
                }
                spin_unlock_irqrestore(&hc->lock, flags);
                break;
        case PH_ACTIVATE_IND:
                test_and_set_bit(FLG_ACTIVE, &dch->Flags);
                _queue_data(&dch->dev.D, cmd, MISDN_ID_ANY, 0, NULL,
                            GFP_ATOMIC);
                break;
        case PH_DEACTIVATE_IND:
                test_and_clear_bit(FLG_ACTIVE, &dch->Flags);
                _queue_data(&dch->dev.D, cmd, MISDN_ID_ANY, 0, NULL,
                            GFP_ATOMIC);
                break;
        default:
                if (dch->debug & DEBUG_HW)
                        printk(KERN_DEBUG "%s: unknown command %x\n",
                               __func__, cmd);
                return -1;
        }
        return 0;
}

/*
 * Layer2 -> Layer 1 Transfer
 */

static int
handle_dmsg(struct mISDNchannel *ch, struct sk_buff *skb)
{
        struct mISDNdevice      *dev = container_of(ch, struct mISDNdevice, D);
        struct dchannel         *dch = container_of(dev, struct dchannel, dev);
        struct hfc_multi        *hc = dch->hw;
        struct mISDNhead        *hh = mISDN_HEAD_P(skb);
        int                     ret = -EINVAL;
        unsigned int            id;
        u_long                  flags;

        switch (hh->prim) {
        case PH_DATA_REQ:
                if (skb->len < 1)
                        break;
                spin_lock_irqsave(&hc->lock, flags);
                ret = dchannel_senddata(dch, skb);
                if (ret > 0) { /* direct TX */
                        id = hh->id; /* skb can be freed */
                        hfcmulti_tx(hc, dch->slot);
                        ret = 0;
                        /* start fifo */
                        HFC_outb(hc, R_FIFO, 0);
                        HFC_wait(hc);
                        spin_unlock_irqrestore(&hc->lock, flags);
                        queue_ch_frame(ch, PH_DATA_CNF, id, NULL);
                } else
                        spin_unlock_irqrestore(&hc->lock, flags);
                return ret;
        case PH_ACTIVATE_REQ:
                if (dch->dev.D.protocol != ISDN_P_TE_S0) {
                        spin_lock_irqsave(&hc->lock, flags);
                        ret = 0;
                        if (debug & DEBUG_HFCMULTI_MSG)
                                printk(KERN_DEBUG
                                       "%s: PH_ACTIVATE port %d (0..%d)\n",
                                       __func__, hc->chan[dch->slot].port,
                                       hc->ports - 1);
                        /* start activation */
                        if (hc->ctype == HFC_TYPE_E1) {
                                ph_state_change(dch);
                                if (debug & DEBUG_HFCMULTI_STATE)
                                        printk(KERN_DEBUG
                                               "%s: E1 report state %x \n",
                                               __func__, dch->state);
                        } else {
                                HFC_outb(hc, R_ST_SEL,
                                         hc->chan[dch->slot].port);
                                /* undocumented: delay after R_ST_SEL */
                                udelay(1);
                                HFC_outb(hc, A_ST_WR_STATE, V_ST_LD_STA | 1);
                                /* G1 */
                                udelay(6); /* wait at least 5,21us */
                                HFC_outb(hc, A_ST_WR_STATE, 1);
                                HFC_outb(hc, A_ST_WR_STATE, 1 |
                                         (V_ST_ACT * 3)); /* activate */
                                dch->state = 1;
                        }
                        spin_unlock_irqrestore(&hc->lock, flags);
                } else
                        ret = l1_event(dch->l1, hh->prim);
                break;
        case PH_DEACTIVATE_REQ:
                test_and_clear_bit(FLG_L2_ACTIVATED, &dch->Flags);
                if (dch->dev.D.protocol != ISDN_P_TE_S0) {
                        struct sk_buff_head free_queue;

                        __skb_queue_head_init(&free_queue);
                        spin_lock_irqsave(&hc->lock, flags);
                        if (debug & DEBUG_HFCMULTI_MSG)
                                printk(KERN_DEBUG
                                       "%s: PH_DEACTIVATE port %d (0..%d)\n",
                                       __func__, hc->chan[dch->slot].port,
                                       hc->ports - 1);
                        /* start deactivation */
                        if (hc->ctype == HFC_TYPE_E1) {
                                if (debug & DEBUG_HFCMULTI_MSG)
                                        printk(KERN_DEBUG
                                               "%s: PH_DEACTIVATE no BRI\n",
                                               __func__);
                        } else {
                                HFC_outb(hc, R_ST_SEL,
                                         hc->chan[dch->slot].port);
                                /* undocumented: delay after R_ST_SEL */
                                udelay(1);
                                HFC_outb(hc, A_ST_WR_STATE, V_ST_ACT * 2);
                                /* deactivate */
                                dch->state = 1;
                        }
                        skb_queue_splice_init(&dch->squeue, &free_queue);
                        if (dch->tx_skb) {
                                __skb_queue_tail(&free_queue, dch->tx_skb);
                                dch->tx_skb = NULL;
                        }
                        dch->tx_idx = 0;
                        if (dch->rx_skb) {
                                __skb_queue_tail(&free_queue, dch->rx_skb);
                                dch->rx_skb = NULL;
                        }
                        test_and_clear_bit(FLG_TX_BUSY, &dch->Flags);
                        if (test_and_clear_bit(FLG_BUSY_TIMER, &dch->Flags))
                                timer_delete(&dch->timer);
#ifdef FIXME
                        if (test_and_clear_bit(FLG_L1_BUSY, &dch->Flags))
                                dchannel_sched_event(&hc->dch, D_CLEARBUSY);
#endif
                        ret = 0;
                        spin_unlock_irqrestore(&hc->lock, flags);
                        __skb_queue_purge(&free_queue);
                } else
                        ret = l1_event(dch->l1, hh->prim);
                break;
        }
        if (!ret)
                dev_kfree_skb(skb);
        return ret;
}

static void
deactivate_bchannel(struct bchannel *bch)
{
        struct hfc_multi        *hc = bch->hw;
        u_long                  flags;

        spin_lock_irqsave(&hc->lock, flags);
        mISDN_clear_bchannel(bch);
        hc->chan[bch->slot].coeff_count = 0;
        hc->chan[bch->slot].rx_off = 0;
        hc->chan[bch->slot].conf = -1;
        mode_hfcmulti(hc, bch->slot, ISDN_P_NONE, -1, 0, -1, 0);
        spin_unlock_irqrestore(&hc->lock, flags);
}

static int
handle_bmsg(struct mISDNchannel *ch, struct sk_buff *skb)
{
        struct bchannel         *bch = container_of(ch, struct bchannel, ch);
        struct hfc_multi        *hc = bch->hw;
        int                     ret = -EINVAL;
        struct mISDNhead        *hh = mISDN_HEAD_P(skb);
        unsigned long           flags;

        switch (hh->prim) {
        case PH_DATA_REQ:
                if (!skb->len)
                        break;
                spin_lock_irqsave(&hc->lock, flags);
                ret = bchannel_senddata(bch, skb);
                if (ret > 0) { /* direct TX */
                        hfcmulti_tx(hc, bch->slot);
                        ret = 0;
                        /* start fifo */
                        HFC_outb_nodebug(hc, R_FIFO, 0);
                        HFC_wait_nodebug(hc);
                }
                spin_unlock_irqrestore(&hc->lock, flags);
                return ret;
        case PH_ACTIVATE_REQ:
                if (debug & DEBUG_HFCMULTI_MSG)
                        printk(KERN_DEBUG "%s: PH_ACTIVATE ch %d (0..32)\n",
                               __func__, bch->slot);
                spin_lock_irqsave(&hc->lock, flags);
                /* activate B-channel if not already activated */
                if (!test_and_set_bit(FLG_ACTIVE, &bch->Flags)) {
                        hc->chan[bch->slot].txpending = 0;
                        ret = mode_hfcmulti(hc, bch->slot,
                                            ch->protocol,
                                            hc->chan[bch->slot].slot_tx,
                                            hc->chan[bch->slot].bank_tx,
                                            hc->chan[bch->slot].slot_rx,
                                            hc->chan[bch->slot].bank_rx);
                        if (!ret) {
                                if (ch->protocol == ISDN_P_B_RAW && !hc->dtmf
                                    && test_bit(HFC_CHIP_DTMF, &hc->chip)) {
                                        /* start decoder */
                                        hc->dtmf = 1;
                                        if (debug & DEBUG_HFCMULTI_DTMF)
                                                printk(KERN_DEBUG
                                                       "%s: start dtmf decoder\n",
                                                       __func__);
                                        HFC_outb(hc, R_DTMF, hc->hw.r_dtmf |
                                                 V_RST_DTMF);
                                }
                        }
                } else
                        ret = 0;
                spin_unlock_irqrestore(&hc->lock, flags);
                if (!ret)
                        _queue_data(ch, PH_ACTIVATE_IND, MISDN_ID_ANY, 0, NULL,
                                    GFP_KERNEL);
                break;
        case PH_CONTROL_REQ:
                spin_lock_irqsave(&hc->lock, flags);
                switch (hh->id) {
                case HFC_SPL_LOOP_ON: /* set sample loop */
                        if (debug & DEBUG_HFCMULTI_MSG)
                                printk(KERN_DEBUG
                                       "%s: HFC_SPL_LOOP_ON (len = %d)\n",
                                       __func__, skb->len);
                        ret = 0;
                        break;
                case HFC_SPL_LOOP_OFF: /* set silence */
                        if (debug & DEBUG_HFCMULTI_MSG)
                                printk(KERN_DEBUG "%s: HFC_SPL_LOOP_OFF\n",
                                       __func__);
                        ret = 0;
                        break;
                default:
                        printk(KERN_ERR
                               "%s: unknown PH_CONTROL_REQ info %x\n",
                               __func__, hh->id);
                        ret = -EINVAL;
                }
                spin_unlock_irqrestore(&hc->lock, flags);
                break;
        case PH_DEACTIVATE_REQ:
                deactivate_bchannel(bch); /* locked there */
                _queue_data(ch, PH_DEACTIVATE_IND, MISDN_ID_ANY, 0, NULL,
                            GFP_KERNEL);
                ret = 0;
                break;
        }
        if (!ret)
                dev_kfree_skb(skb);
        return ret;
}

/*
 * bchannel control function
 */
static int
channel_bctrl(struct bchannel *bch, struct mISDN_ctrl_req *cq)
{
        int                     ret = 0;
        struct dsp_features     *features =
                (struct dsp_features *)(*((u_long *)&cq->p1));
        struct hfc_multi        *hc = bch->hw;
        int                     slot_tx;
        int                     bank_tx;
        int                     slot_rx;
        int                     bank_rx;
        int                     num;

        switch (cq->op) {
        case MISDN_CTRL_GETOP:
                ret = mISDN_ctrl_bchannel(bch, cq);
                cq->op |= MISDN_CTRL_HFC_OP | MISDN_CTRL_HW_FEATURES_OP;
                break;
        case MISDN_CTRL_RX_OFF: /* turn off / on rx stream */
                ret = mISDN_ctrl_bchannel(bch, cq);
                hc->chan[bch->slot].rx_off = !!cq->p1;
                if (!hc->chan[bch->slot].rx_off) {
                        /* reset fifo on rx on */
                        HFC_outb_nodebug(hc, R_FIFO, (bch->slot << 1) | 1);
                        HFC_wait_nodebug(hc);
                        HFC_outb_nodebug(hc, R_INC_RES_FIFO, V_RES_F);
                        HFC_wait_nodebug(hc);
                }
                if (debug & DEBUG_HFCMULTI_MSG)
                        printk(KERN_DEBUG "%s: RX_OFF request (nr=%d off=%d)\n",
                               __func__, bch->nr, hc->chan[bch->slot].rx_off);
                break;
        case MISDN_CTRL_FILL_EMPTY:
                ret = mISDN_ctrl_bchannel(bch, cq);
                hc->silence = bch->fill[0];
                memset(hc->silence_data, hc->silence, sizeof(hc->silence_data));
                break;
        case MISDN_CTRL_HW_FEATURES: /* fill features structure */
                if (debug & DEBUG_HFCMULTI_MSG)
                        printk(KERN_DEBUG "%s: HW_FEATURE request\n",
                               __func__);
                /* create confirm */
                features->hfc_id = hc->id;
                if (test_bit(HFC_CHIP_DTMF, &hc->chip))
                        features->hfc_dtmf = 1;
                if (test_bit(HFC_CHIP_CONF, &hc->chip))
                        features->hfc_conf = 1;
                features->hfc_loops = 0;
                if (test_bit(HFC_CHIP_B410P, &hc->chip)) {
                        features->hfc_echocanhw = 1;
                } else {
                        features->pcm_id = hc->pcm;
                        features->pcm_slots = hc->slots;
                        features->pcm_banks = 2;
                }
                break;
        case MISDN_CTRL_HFC_PCM_CONN: /* connect to pcm timeslot (0..N) */
                slot_tx = cq->p1 & 0xff;
                bank_tx = cq->p1 >> 8;
                slot_rx = cq->p2 & 0xff;
                bank_rx = cq->p2 >> 8;
                if (debug & DEBUG_HFCMULTI_MSG)
                        printk(KERN_DEBUG
                               "%s: HFC_PCM_CONN slot %d bank %d (TX) "
                               "slot %d bank %d (RX)\n",
                               __func__, slot_tx, bank_tx,
                               slot_rx, bank_rx);
                if (slot_tx < hc->slots && bank_tx <= 2 &&
                    slot_rx < hc->slots && bank_rx <= 2)
                        hfcmulti_pcm(hc, bch->slot,
                                     slot_tx, bank_tx, slot_rx, bank_rx);
                else {
                        printk(KERN_WARNING
                               "%s: HFC_PCM_CONN slot %d bank %d (TX) "
                               "slot %d bank %d (RX) out of range\n",
                               __func__, slot_tx, bank_tx,
                               slot_rx, bank_rx);
                        ret = -EINVAL;
                }
                break;
        case MISDN_CTRL_HFC_PCM_DISC: /* release interface from pcm timeslot */
                if (debug & DEBUG_HFCMULTI_MSG)
                        printk(KERN_DEBUG "%s: HFC_PCM_DISC\n",
                               __func__);
                hfcmulti_pcm(hc, bch->slot, -1, 0, -1, 0);
                break;
        case MISDN_CTRL_HFC_CONF_JOIN: /* join conference (0..7) */
                num = cq->p1 & 0xff;
                if (debug & DEBUG_HFCMULTI_MSG)
                        printk(KERN_DEBUG "%s: HFC_CONF_JOIN conf %d\n",
                               __func__, num);
                if (num <= 7)
                        hfcmulti_conf(hc, bch->slot, num);
                else {
                        printk(KERN_WARNING
                               "%s: HW_CONF_JOIN conf %d out of range\n",
                               __func__, num);
                        ret = -EINVAL;
                }
                break;
        case MISDN_CTRL_HFC_CONF_SPLIT: /* split conference */
                if (debug & DEBUG_HFCMULTI_MSG)
                        printk(KERN_DEBUG "%s: HFC_CONF_SPLIT\n", __func__);
                hfcmulti_conf(hc, bch->slot, -1);
                break;
        case MISDN_CTRL_HFC_ECHOCAN_ON:
                if (debug & DEBUG_HFCMULTI_MSG)
                        printk(KERN_DEBUG "%s: HFC_ECHOCAN_ON\n", __func__);
                if (test_bit(HFC_CHIP_B410P, &hc->chip))
                        vpm_echocan_on(hc, bch->slot, cq->p1);
                else
                        ret = -EINVAL;
                break;

        case MISDN_CTRL_HFC_ECHOCAN_OFF:
                if (debug & DEBUG_HFCMULTI_MSG)
                        printk(KERN_DEBUG "%s: HFC_ECHOCAN_OFF\n",
                               __func__);
                if (test_bit(HFC_CHIP_B410P, &hc->chip))
                        vpm_echocan_off(hc, bch->slot);
                else
                        ret = -EINVAL;
                break;
        default:
                ret = mISDN_ctrl_bchannel(bch, cq);
                break;
        }
        return ret;
}

static int
hfcm_bctrl(struct mISDNchannel *ch, u_int cmd, void *arg)
{
        struct bchannel         *bch = container_of(ch, struct bchannel, ch);
        struct hfc_multi        *hc = bch->hw;
        int                     err = -EINVAL;
        u_long  flags;

        if (bch->debug & DEBUG_HW)
                printk(KERN_DEBUG "%s: cmd:%x %p\n",
                       __func__, cmd, arg);
        switch (cmd) {
        case CLOSE_CHANNEL:
                test_and_clear_bit(FLG_OPEN, &bch->Flags);
                deactivate_bchannel(bch); /* locked there */
                ch->protocol = ISDN_P_NONE;
                ch->peer = NULL;
                module_put(THIS_MODULE);
                err = 0;
                break;
        case CONTROL_CHANNEL:
                spin_lock_irqsave(&hc->lock, flags);
                err = channel_bctrl(bch, arg);
                spin_unlock_irqrestore(&hc->lock, flags);
                break;
        default:
                printk(KERN_WARNING "%s: unknown prim(%x)\n",
                       __func__, cmd);
        }
        return err;
}

/*
 * handle D-channel events
 *
 * handle state change event
 */
static void
ph_state_change(struct dchannel *dch)
{
        struct hfc_multi *hc;
        int ch, i;

        if (!dch) {
                printk(KERN_WARNING "%s: ERROR given dch is NULL\n", __func__);
                return;
        }
        hc = dch->hw;
        ch = dch->slot;

        if (hc->ctype == HFC_TYPE_E1) {
                if (dch->dev.D.protocol == ISDN_P_TE_E1) {
                        if (debug & DEBUG_HFCMULTI_STATE)
                                printk(KERN_DEBUG
                                       "%s: E1 TE (id=%d) newstate %x\n",
                                       __func__, hc->id, dch->state);
                } else {
                        if (debug & DEBUG_HFCMULTI_STATE)
                                printk(KERN_DEBUG
                                       "%s: E1 NT (id=%d) newstate %x\n",
                                       __func__, hc->id, dch->state);
                }
                switch (dch->state) {
                case (1):
                        if (hc->e1_state != 1) {
                                for (i = 1; i <= 31; i++) {
                                        /* reset fifos on e1 activation */
                                        HFC_outb_nodebug(hc, R_FIFO,
                                                         (i << 1) | 1);
                                        HFC_wait_nodebug(hc);
                                        HFC_outb_nodebug(hc, R_INC_RES_FIFO,
                                                         V_RES_F);
                                        HFC_wait_nodebug(hc);
                                }
                        }
                        test_and_set_bit(FLG_ACTIVE, &dch->Flags);
                        _queue_data(&dch->dev.D, PH_ACTIVATE_IND,
                                    MISDN_ID_ANY, 0, NULL, GFP_ATOMIC);
                        break;

                default:
                        if (hc->e1_state != 1)
                                return;
                        test_and_clear_bit(FLG_ACTIVE, &dch->Flags);
                        _queue_data(&dch->dev.D, PH_DEACTIVATE_IND,
                                    MISDN_ID_ANY, 0, NULL, GFP_ATOMIC);
                }
                hc->e1_state = dch->state;
        } else {
                if (dch->dev.D.protocol == ISDN_P_TE_S0) {
                        if (debug & DEBUG_HFCMULTI_STATE)
                                printk(KERN_DEBUG
                                       "%s: S/T TE newstate %x\n",
                                       __func__, dch->state);
                        switch (dch->state) {
                        case (0):
                                l1_event(dch->l1, HW_RESET_IND);
                                break;
                        case (3):
                                l1_event(dch->l1, HW_DEACT_IND);
                                break;
                        case (5):
                        case (8):
                                l1_event(dch->l1, ANYSIGNAL);
                                break;
                        case (6):
                                l1_event(dch->l1, INFO2);
                                break;
                        case (7):
                                l1_event(dch->l1, INFO4_P8);
                                break;
                        }
                } else {
                        if (debug & DEBUG_HFCMULTI_STATE)
                                printk(KERN_DEBUG "%s: S/T NT newstate %x\n",
                                       __func__, dch->state);
                        switch (dch->state) {
                        case (2):
                                if (hc->chan[ch].nt_timer == 0) {
                                        hc->chan[ch].nt_timer = -1;
                                        HFC_outb(hc, R_ST_SEL,
                                                 hc->chan[ch].port);
                                        /* undocumented: delay after R_ST_SEL */
                                        udelay(1);
                                        HFC_outb(hc, A_ST_WR_STATE, 4 |
                                                 V_ST_LD_STA); /* G4 */
                                        udelay(6); /* wait at least 5,21us */
                                        HFC_outb(hc, A_ST_WR_STATE, 4);
                                        dch->state = 4;
                                } else {
                                        /* one extra count for the next event */
                                        hc->chan[ch].nt_timer =
                                                nt_t1_count[poll_timer] + 1;
                                        HFC_outb(hc, R_ST_SEL,
                                                 hc->chan[ch].port);
                                        /* undocumented: delay after R_ST_SEL */
                                        udelay(1);
                                        /* allow G2 -> G3 transition */
                                        HFC_outb(hc, A_ST_WR_STATE, 2 |
                                                 V_SET_G2_G3);
                                }
                                break;
                        case (1):
                                hc->chan[ch].nt_timer = -1;
                                test_and_clear_bit(FLG_ACTIVE, &dch->Flags);
                                _queue_data(&dch->dev.D, PH_DEACTIVATE_IND,
                                            MISDN_ID_ANY, 0, NULL, GFP_ATOMIC);
                                break;
                        case (4):
                                hc->chan[ch].nt_timer = -1;
                                break;
                        case (3):
                                hc->chan[ch].nt_timer = -1;
                                test_and_set_bit(FLG_ACTIVE, &dch->Flags);
                                _queue_data(&dch->dev.D, PH_ACTIVATE_IND,
                                            MISDN_ID_ANY, 0, NULL, GFP_ATOMIC);
                                break;
                        }
                }
        }
}

/*
 * called for card mode init message
 */

static void
hfcmulti_initmode(struct dchannel *dch)
{
        struct hfc_multi *hc = dch->hw;
        u_char          a_st_wr_state, r_e1_wr_sta;
        int             i, pt;

        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: entered\n", __func__);

        i = dch->slot;
        pt = hc->chan[i].port;
        if (hc->ctype == HFC_TYPE_E1) {
                /* E1 */
                hc->chan[hc->dnum[pt]].slot_tx = -1;
                hc->chan[hc->dnum[pt]].slot_rx = -1;
                hc->chan[hc->dnum[pt]].conf = -1;
                if (hc->dnum[pt]) {
                        mode_hfcmulti(hc, dch->slot, dch->dev.D.protocol,
                                      -1, 0, -1, 0);
                        timer_setup(&dch->timer, hfcmulti_dbusy_timer, 0);
                }
                for (i = 1; i <= 31; i++) {
                        if (!((1 << i) & hc->bmask[pt])) /* skip unused chan */
                                continue;
                        hc->chan[i].slot_tx = -1;
                        hc->chan[i].slot_rx = -1;
                        hc->chan[i].conf = -1;
                        mode_hfcmulti(hc, i, ISDN_P_NONE, -1, 0, -1, 0);
                }
        }
        if (hc->ctype == HFC_TYPE_E1 && pt == 0) {
                /* E1, port 0 */
                dch = hc->chan[hc->dnum[0]].dch;
                if (test_bit(HFC_CFG_REPORT_LOS, &hc->chan[hc->dnum[0]].cfg)) {
                        HFC_outb(hc, R_LOS0, 255); /* 2 ms */
                        HFC_outb(hc, R_LOS1, 255); /* 512 ms */
                }
                if (test_bit(HFC_CFG_OPTICAL, &hc->chan[hc->dnum[0]].cfg)) {
                        HFC_outb(hc, R_RX0, 0);
                        hc->hw.r_tx0 = 0 | V_OUT_EN;
                } else {
                        HFC_outb(hc, R_RX0, 1);
                        hc->hw.r_tx0 = 1 | V_OUT_EN;
                }
                hc->hw.r_tx1 = V_ATX | V_NTRI;
                HFC_outb(hc, R_TX0, hc->hw.r_tx0);
                HFC_outb(hc, R_TX1, hc->hw.r_tx1);
                HFC_outb(hc, R_TX_FR0, 0x00);
                HFC_outb(hc, R_TX_FR1, 0xf8);

                if (test_bit(HFC_CFG_CRC4, &hc->chan[hc->dnum[0]].cfg))
                        HFC_outb(hc, R_TX_FR2, V_TX_MF | V_TX_E | V_NEG_E);

                HFC_outb(hc, R_RX_FR0, V_AUTO_RESYNC | V_AUTO_RECO | 0);

                if (test_bit(HFC_CFG_CRC4, &hc->chan[hc->dnum[0]].cfg))
                        HFC_outb(hc, R_RX_FR1, V_RX_MF | V_RX_MF_SYNC);

                if (dch->dev.D.protocol == ISDN_P_NT_E1) {
                        if (debug & DEBUG_HFCMULTI_INIT)
                                printk(KERN_DEBUG "%s: E1 port is NT-mode\n",
                                       __func__);
                        r_e1_wr_sta = 0; /* G0 */
                        hc->e1_getclock = 0;
                } else {
                        if (debug & DEBUG_HFCMULTI_INIT)
                                printk(KERN_DEBUG "%s: E1 port is TE-mode\n",
                                       __func__);
                        r_e1_wr_sta = 0; /* F0 */
                        hc->e1_getclock = 1;
                }
                if (test_bit(HFC_CHIP_RX_SYNC, &hc->chip))
                        HFC_outb(hc, R_SYNC_OUT, V_SYNC_E1_RX);
                else
                        HFC_outb(hc, R_SYNC_OUT, 0);
                if (test_bit(HFC_CHIP_E1CLOCK_GET, &hc->chip))
                        hc->e1_getclock = 1;
                if (test_bit(HFC_CHIP_E1CLOCK_PUT, &hc->chip))
                        hc->e1_getclock = 0;
                if (test_bit(HFC_CHIP_PCM_SLAVE, &hc->chip)) {
                        /* SLAVE (clock master) */
                        if (debug & DEBUG_HFCMULTI_INIT)
                                printk(KERN_DEBUG
                                       "%s: E1 port is clock master "
                                       "(clock from PCM)\n", __func__);
                        HFC_outb(hc, R_SYNC_CTRL, V_EXT_CLK_SYNC | V_PCM_SYNC);
                } else {
                        if (hc->e1_getclock) {
                                /* MASTER (clock slave) */
                                if (debug & DEBUG_HFCMULTI_INIT)
                                        printk(KERN_DEBUG
                                               "%s: E1 port is clock slave "
                                               "(clock to PCM)\n", __func__);
                                HFC_outb(hc, R_SYNC_CTRL, V_SYNC_OFFS);
                        } else {
                                /* MASTER (clock master) */
                                if (debug & DEBUG_HFCMULTI_INIT)
                                        printk(KERN_DEBUG "%s: E1 port is "
                                               "clock master "
                                               "(clock from QUARTZ)\n",
                                               __func__);
                                HFC_outb(hc, R_SYNC_CTRL, V_EXT_CLK_SYNC |
                                         V_PCM_SYNC | V_JATT_OFF);
                                HFC_outb(hc, R_SYNC_OUT, 0);
                        }
                }
                HFC_outb(hc, R_JATT_ATT, 0x9c); /* undoc register */
                HFC_outb(hc, R_PWM_MD, V_PWM0_MD);
                HFC_outb(hc, R_PWM0, 0x50);
                HFC_outb(hc, R_PWM1, 0xff);
                /* state machine setup */
                HFC_outb(hc, R_E1_WR_STA, r_e1_wr_sta | V_E1_LD_STA);
                udelay(6); /* wait at least 5,21us */
                HFC_outb(hc, R_E1_WR_STA, r_e1_wr_sta);
                if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                        hc->syncronized = 0;
                        plxsd_checksync(hc, 0);
                }
        }
        if (hc->ctype != HFC_TYPE_E1) {
                /* ST */
                hc->chan[i].slot_tx = -1;
                hc->chan[i].slot_rx = -1;
                hc->chan[i].conf = -1;
                mode_hfcmulti(hc, i, dch->dev.D.protocol, -1, 0, -1, 0);
                timer_setup(&dch->timer, hfcmulti_dbusy_timer, 0);
                hc->chan[i - 2].slot_tx = -1;
                hc->chan[i - 2].slot_rx = -1;
                hc->chan[i - 2].conf = -1;
                mode_hfcmulti(hc, i - 2, ISDN_P_NONE, -1, 0, -1, 0);
                hc->chan[i - 1].slot_tx = -1;
                hc->chan[i - 1].slot_rx = -1;
                hc->chan[i - 1].conf = -1;
                mode_hfcmulti(hc, i - 1, ISDN_P_NONE, -1, 0, -1, 0);
                /* select interface */
                HFC_outb(hc, R_ST_SEL, pt);
                /* undocumented: delay after R_ST_SEL */
                udelay(1);
                if (dch->dev.D.protocol == ISDN_P_NT_S0) {
                        if (debug & DEBUG_HFCMULTI_INIT)
                                printk(KERN_DEBUG
                                       "%s: ST port %d is NT-mode\n",
                                       __func__, pt);
                        /* clock delay */
                        HFC_outb(hc, A_ST_CLK_DLY, clockdelay_nt);
                        a_st_wr_state = 1; /* G1 */
                        hc->hw.a_st_ctrl0[pt] = V_ST_MD;
                } else {
                        if (debug & DEBUG_HFCMULTI_INIT)
                                printk(KERN_DEBUG
                                       "%s: ST port %d is TE-mode\n",
                                       __func__, pt);
                        /* clock delay */
                        HFC_outb(hc, A_ST_CLK_DLY, clockdelay_te);
                        a_st_wr_state = 2; /* F2 */
                        hc->hw.a_st_ctrl0[pt] = 0;
                }
                if (!test_bit(HFC_CFG_NONCAP_TX, &hc->chan[i].cfg))
                        hc->hw.a_st_ctrl0[pt] |= V_TX_LI;
                if (hc->ctype == HFC_TYPE_XHFC) {
                        hc->hw.a_st_ctrl0[pt] |= 0x40 /* V_ST_PU_CTRL */;
                        HFC_outb(hc, 0x35 /* A_ST_CTRL3 */,
                                 0x7c << 1 /* V_ST_PULSE */);
                }
                /* line setup */
                HFC_outb(hc, A_ST_CTRL0,  hc->hw.a_st_ctrl0[pt]);
                /* disable E-channel */
                if ((dch->dev.D.protocol == ISDN_P_NT_S0) ||
                    test_bit(HFC_CFG_DIS_ECHANNEL, &hc->chan[i].cfg))
                        HFC_outb(hc, A_ST_CTRL1, V_E_IGNO);
                else
                        HFC_outb(hc, A_ST_CTRL1, 0);
                /* enable B-channel receive */
                HFC_outb(hc, A_ST_CTRL2,  V_B1_RX_EN | V_B2_RX_EN);
                /* state machine setup */
                HFC_outb(hc, A_ST_WR_STATE, a_st_wr_state | V_ST_LD_STA);
                udelay(6); /* wait at least 5,21us */
                HFC_outb(hc, A_ST_WR_STATE, a_st_wr_state);
                hc->hw.r_sci_msk |= 1 << pt;
                /* state machine interrupts */
                HFC_outb(hc, R_SCI_MSK, hc->hw.r_sci_msk);
                /* unset sync on port */
                if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                        hc->syncronized &=
                                ~(1 << hc->chan[dch->slot].port);
                        plxsd_checksync(hc, 0);
                }
        }
        if (debug & DEBUG_HFCMULTI_INIT)
                printk("%s: done\n", __func__);
}


static int
open_dchannel(struct hfc_multi *hc, struct dchannel *dch,
              struct channel_req *rq)
{
        int     err = 0;
        u_long  flags;

        if (debug & DEBUG_HW_OPEN)
                printk(KERN_DEBUG "%s: dev(%d) open from %p\n", __func__,
                       dch->dev.id, __builtin_return_address(0));
        if (rq->protocol == ISDN_P_NONE)
                return -EINVAL;
        if ((dch->dev.D.protocol != ISDN_P_NONE) &&
            (dch->dev.D.protocol != rq->protocol)) {
                if (debug & DEBUG_HFCMULTI_MODE)
                        printk(KERN_DEBUG "%s: change protocol %x to %x\n",
                               __func__, dch->dev.D.protocol, rq->protocol);
        }
        if ((dch->dev.D.protocol == ISDN_P_TE_S0) &&
            (rq->protocol != ISDN_P_TE_S0))
                l1_event(dch->l1, CLOSE_CHANNEL);
        if (dch->dev.D.protocol != rq->protocol) {
                if (rq->protocol == ISDN_P_TE_S0) {
                        err = create_l1(dch, hfcm_l1callback);
                        if (err)
                                return err;
                }
                dch->dev.D.protocol = rq->protocol;
                spin_lock_irqsave(&hc->lock, flags);
                hfcmulti_initmode(dch);
                spin_unlock_irqrestore(&hc->lock, flags);
        }
        if (test_bit(FLG_ACTIVE, &dch->Flags))
                _queue_data(&dch->dev.D, PH_ACTIVATE_IND, MISDN_ID_ANY,
                            0, NULL, GFP_KERNEL);
        rq->ch = &dch->dev.D;
        if (!try_module_get(THIS_MODULE))
                printk(KERN_WARNING "%s:cannot get module\n", __func__);
        return 0;
}

static int
open_bchannel(struct hfc_multi *hc, struct dchannel *dch,
              struct channel_req *rq)
{
        struct bchannel *bch;
        int             ch;

        if (!test_channelmap(rq->adr.channel, dch->dev.channelmap))
                return -EINVAL;
        if (rq->protocol == ISDN_P_NONE)
                return -EINVAL;
        if (hc->ctype == HFC_TYPE_E1)
                ch = rq->adr.channel;
        else
                ch = (rq->adr.channel - 1) + (dch->slot - 2);
        bch = hc->chan[ch].bch;
        if (!bch) {
                printk(KERN_ERR "%s:internal error ch %d has no bch\n",
                       __func__, ch);
                return -EINVAL;
        }
        if (test_and_set_bit(FLG_OPEN, &bch->Flags))
                return -EBUSY; /* b-channel can be only open once */
        bch->ch.protocol = rq->protocol;
        hc->chan[ch].rx_off = 0;
        rq->ch = &bch->ch;
        if (!try_module_get(THIS_MODULE))
                printk(KERN_WARNING "%s:cannot get module\n", __func__);
        return 0;
}

/*
 * device control function
 */
static int
channel_dctrl(struct dchannel *dch, struct mISDN_ctrl_req *cq)
{
        struct hfc_multi        *hc = dch->hw;
        int     ret = 0;
        int     wd_mode, wd_cnt;

        switch (cq->op) {
        case MISDN_CTRL_GETOP:
                cq->op = MISDN_CTRL_HFC_OP | MISDN_CTRL_L1_TIMER3;
                break;
        case MISDN_CTRL_HFC_WD_INIT: /* init the watchdog */
                wd_cnt = cq->p1 & 0xf;
                wd_mode = !!(cq->p1 >> 4);
                if (debug & DEBUG_HFCMULTI_MSG)
                        printk(KERN_DEBUG "%s: MISDN_CTRL_HFC_WD_INIT mode %s"
                               ", counter 0x%x\n", __func__,
                               wd_mode ? "AUTO" : "MANUAL", wd_cnt);
                /* set the watchdog timer */
                HFC_outb(hc, R_TI_WD, poll_timer | (wd_cnt << 4));
                hc->hw.r_bert_wd_md = (wd_mode ? V_AUTO_WD_RES : 0);
                if (hc->ctype == HFC_TYPE_XHFC)
                        hc->hw.r_bert_wd_md |= 0x40 /* V_WD_EN */;
                /* init the watchdog register and reset the counter */
                HFC_outb(hc, R_BERT_WD_MD, hc->hw.r_bert_wd_md | V_WD_RES);
                if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                        /* enable the watchdog output for Speech-Design */
                        HFC_outb(hc, R_GPIO_SEL,  V_GPIO_SEL7);
                        HFC_outb(hc, R_GPIO_EN1,  V_GPIO_EN15);
                        HFC_outb(hc, R_GPIO_OUT1, 0);
                        HFC_outb(hc, R_GPIO_OUT1, V_GPIO_OUT15);
                }
                break;
        case MISDN_CTRL_HFC_WD_RESET: /* reset the watchdog counter */
                if (debug & DEBUG_HFCMULTI_MSG)
                        printk(KERN_DEBUG "%s: MISDN_CTRL_HFC_WD_RESET\n",
                               __func__);
                HFC_outb(hc, R_BERT_WD_MD, hc->hw.r_bert_wd_md | V_WD_RES);
                break;
        case MISDN_CTRL_L1_TIMER3:
                ret = l1_event(dch->l1, HW_TIMER3_VALUE | (cq->p1 & 0xff));
                break;
        default:
                printk(KERN_WARNING "%s: unknown Op %x\n",
                       __func__, cq->op);
                ret = -EINVAL;
                break;
        }
        return ret;
}

static int
hfcm_dctrl(struct mISDNchannel *ch, u_int cmd, void *arg)
{
        struct mISDNdevice      *dev = container_of(ch, struct mISDNdevice, D);
        struct dchannel         *dch = container_of(dev, struct dchannel, dev);
        struct hfc_multi        *hc = dch->hw;
        struct channel_req      *rq;
        int                     err = 0;
        u_long                  flags;

        if (dch->debug & DEBUG_HW)
                printk(KERN_DEBUG "%s: cmd:%x %p\n",
                       __func__, cmd, arg);
        switch (cmd) {
        case OPEN_CHANNEL:
                rq = arg;
                switch (rq->protocol) {
                case ISDN_P_TE_S0:
                case ISDN_P_NT_S0:
                        if (hc->ctype == HFC_TYPE_E1) {
                                err = -EINVAL;
                                break;
                        }
                        err = open_dchannel(hc, dch, rq); /* locked there */
                        break;
                case ISDN_P_TE_E1:
                case ISDN_P_NT_E1:
                        if (hc->ctype != HFC_TYPE_E1) {
                                err = -EINVAL;
                                break;
                        }
                        err = open_dchannel(hc, dch, rq); /* locked there */
                        break;
                default:
                        spin_lock_irqsave(&hc->lock, flags);
                        err = open_bchannel(hc, dch, rq);
                        spin_unlock_irqrestore(&hc->lock, flags);
                }
                break;
        case CLOSE_CHANNEL:
                if (debug & DEBUG_HW_OPEN)
                        printk(KERN_DEBUG "%s: dev(%d) close from %p\n",
                               __func__, dch->dev.id,
                               __builtin_return_address(0));
                module_put(THIS_MODULE);
                break;
        case CONTROL_CHANNEL:
                spin_lock_irqsave(&hc->lock, flags);
                err = channel_dctrl(dch, arg);
                spin_unlock_irqrestore(&hc->lock, flags);
                break;
        default:
                if (dch->debug & DEBUG_HW)
                        printk(KERN_DEBUG "%s: unknown command %x\n",
                               __func__, cmd);
                err = -EINVAL;
        }
        return err;
}

static int
clockctl(void *priv, int enable)
{
        struct hfc_multi *hc = priv;

        hc->iclock_on = enable;
        return 0;
}

/*
 * initialize the card
 */

/*
 * start timer irq, wait some time and check if we have interrupts.
 * if not, reset chip and try again.
 */
static int
init_card(struct hfc_multi *hc)
{
        int     err = -EIO;
        u_long  flags;
        void    __iomem *plx_acc;
        u_long  plx_flags;

        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: entered\n", __func__);

        spin_lock_irqsave(&hc->lock, flags);
        /* set interrupts but leave global interrupt disabled */
        hc->hw.r_irq_ctrl = V_FIFO_IRQ;
        disable_hwirq(hc);
        spin_unlock_irqrestore(&hc->lock, flags);

        if (request_irq(hc->irq, hfcmulti_interrupt, IRQF_SHARED,
                        "HFC-multi", hc)) {
                printk(KERN_WARNING "mISDN: Could not get interrupt %d.\n",
                       hc->irq);
                hc->irq = 0;
                return -EIO;
        }

        if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                spin_lock_irqsave(&plx_lock, plx_flags);
                plx_acc = hc->plx_membase + PLX_INTCSR;
                writew((PLX_INTCSR_PCIINT_ENABLE | PLX_INTCSR_LINTI1_ENABLE),
                       plx_acc); /* enable PCI & LINT1 irq */
                spin_unlock_irqrestore(&plx_lock, plx_flags);
        }

        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: IRQ %d count %d\n",
                       __func__, hc->irq, hc->irqcnt);
        err = init_chip(hc);
        if (err)
                goto error;
        /*
         * Finally enable IRQ output
         * this is only allowed, if an IRQ routine is already
         * established for this HFC, so don't do that earlier
         */
        spin_lock_irqsave(&hc->lock, flags);
        enable_hwirq(hc);
        spin_unlock_irqrestore(&hc->lock, flags);
        /* printk(KERN_DEBUG "no master irq set!!!\n"); */
        set_current_state(TASK_UNINTERRUPTIBLE);
        schedule_timeout((100 * HZ) / 1000); /* Timeout 100ms */
        /* turn IRQ off until chip is completely initialized */
        spin_lock_irqsave(&hc->lock, flags);
        disable_hwirq(hc);
        spin_unlock_irqrestore(&hc->lock, flags);
        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: IRQ %d count %d\n",
                       __func__, hc->irq, hc->irqcnt);
        if (hc->irqcnt) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: done\n", __func__);

                return 0;
        }
        if (test_bit(HFC_CHIP_PCM_SLAVE, &hc->chip)) {
                printk(KERN_INFO "ignoring missing interrupts\n");
                return 0;
        }

        printk(KERN_ERR "HFC PCI: IRQ(%d) getting no interrupts during init.\n",
               hc->irq);

        err = -EIO;

error:
        if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                spin_lock_irqsave(&plx_lock, plx_flags);
                plx_acc = hc->plx_membase + PLX_INTCSR;
                writew(0x00, plx_acc); /*disable IRQs*/
                spin_unlock_irqrestore(&plx_lock, plx_flags);
        }

        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: free irq %d\n", __func__, hc->irq);
        if (hc->irq) {
                free_irq(hc->irq, hc);
                hc->irq = 0;
        }

        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: done (err=%d)\n", __func__, err);
        return err;
}

/*
 * find pci device and set it up
 */

static int
setup_pci(struct hfc_multi *hc, struct pci_dev *pdev,
          const struct pci_device_id *ent)
{
        struct hm_map   *m = (struct hm_map *)ent->driver_data;

        printk(KERN_INFO
               "HFC-multi: card manufacturer: '%s' card name: '%s' clock: %s\n",
               m->vendor_name, m->card_name, m->clock2 ? "double" : "normal");

        hc->pci_dev = pdev;
        if (m->clock2)
                test_and_set_bit(HFC_CHIP_CLOCK2, &hc->chip);

        if (ent->vendor == PCI_VENDOR_ID_DIGIUM &&
            ent->device == PCI_DEVICE_ID_DIGIUM_HFC4S) {
                test_and_set_bit(HFC_CHIP_B410P, &hc->chip);
                test_and_set_bit(HFC_CHIP_PCM_MASTER, &hc->chip);
                test_and_clear_bit(HFC_CHIP_PCM_SLAVE, &hc->chip);
                hc->slots = 32;
        }

        if (hc->pci_dev->irq <= 0) {
                printk(KERN_WARNING "HFC-multi: No IRQ for PCI card found.\n");
                return -EIO;
        }
        if (pci_enable_device(hc->pci_dev)) {
                printk(KERN_WARNING "HFC-multi: Error enabling PCI card.\n");
                return -EIO;
        }
        hc->leds = m->leds;
        hc->ledstate = 0xAFFEAFFE;
        hc->opticalsupport = m->opticalsupport;

        hc->pci_iobase = 0;
        hc->pci_membase = NULL;
        hc->plx_membase = NULL;

        /* set memory access methods */
        if (m->io_mode) /* use mode from card config */
                hc->io_mode = m->io_mode;
        switch (hc->io_mode) {
        case HFC_IO_MODE_PLXSD:
                test_and_set_bit(HFC_CHIP_PLXSD, &hc->chip);
                hc->slots = 128; /* required */
                hc->HFC_outb = HFC_outb_pcimem;
                hc->HFC_inb = HFC_inb_pcimem;
                hc->HFC_inw = HFC_inw_pcimem;
                hc->HFC_wait = HFC_wait_pcimem;
                hc->read_fifo = read_fifo_pcimem;
                hc->write_fifo = write_fifo_pcimem;
                hc->plx_origmembase =  hc->pci_dev->resource[0].start;
                /* MEMBASE 1 is PLX PCI Bridge */

                if (!hc->plx_origmembase) {
                        printk(KERN_WARNING
                               "HFC-multi: No IO-Memory for PCI PLX bridge found\n");
                        pci_disable_device(hc->pci_dev);
                        return -EIO;
                }

                hc->plx_membase = ioremap(hc->plx_origmembase, 0x80);
                if (!hc->plx_membase) {
                        printk(KERN_WARNING
                               "HFC-multi: failed to remap plx address space. "
                               "(internal error)\n");
                        pci_disable_device(hc->pci_dev);
                        return -EIO;
                }
                printk(KERN_INFO
                       "HFC-multi: plx_membase:%#lx plx_origmembase:%#lx\n",
                       (u_long)hc->plx_membase, hc->plx_origmembase);

                hc->pci_origmembase =  hc->pci_dev->resource[2].start;
                /* MEMBASE 1 is PLX PCI Bridge */
                if (!hc->pci_origmembase) {
                        printk(KERN_WARNING
                               "HFC-multi: No IO-Memory for PCI card found\n");
                        pci_disable_device(hc->pci_dev);
                        return -EIO;
                }

                hc->pci_membase = ioremap(hc->pci_origmembase, 0x400);
                if (!hc->pci_membase) {
                        printk(KERN_WARNING "HFC-multi: failed to remap io "
                               "address space. (internal error)\n");
                        pci_disable_device(hc->pci_dev);
                        return -EIO;
                }

                printk(KERN_INFO
                       "card %d: defined at MEMBASE %#lx (%#lx) IRQ %d HZ %d "
                       "leds-type %d\n",
                       hc->id, (u_long)hc->pci_membase, hc->pci_origmembase,
                       hc->pci_dev->irq, HZ, hc->leds);
                pci_write_config_word(hc->pci_dev, PCI_COMMAND, PCI_ENA_MEMIO);
                break;
        case HFC_IO_MODE_PCIMEM:
                hc->HFC_outb = HFC_outb_pcimem;
                hc->HFC_inb = HFC_inb_pcimem;
                hc->HFC_inw = HFC_inw_pcimem;
                hc->HFC_wait = HFC_wait_pcimem;
                hc->read_fifo = read_fifo_pcimem;
                hc->write_fifo = write_fifo_pcimem;
                hc->pci_origmembase = hc->pci_dev->resource[1].start;
                if (!hc->pci_origmembase) {
                        printk(KERN_WARNING
                               "HFC-multi: No IO-Memory for PCI card found\n");
                        pci_disable_device(hc->pci_dev);
                        return -EIO;
                }

                hc->pci_membase = ioremap(hc->pci_origmembase, 256);
                if (!hc->pci_membase) {
                        printk(KERN_WARNING
                               "HFC-multi: failed to remap io address space. "
                               "(internal error)\n");
                        pci_disable_device(hc->pci_dev);
                        return -EIO;
                }
                printk(KERN_INFO "card %d: defined at MEMBASE %#lx (%#lx) IRQ "
                       "%d HZ %d leds-type %d\n", hc->id, (u_long)hc->pci_membase,
                       hc->pci_origmembase, hc->pci_dev->irq, HZ, hc->leds);
                pci_write_config_word(hc->pci_dev, PCI_COMMAND, PCI_ENA_MEMIO);
                break;
        case HFC_IO_MODE_REGIO:
                hc->HFC_outb = HFC_outb_regio;
                hc->HFC_inb = HFC_inb_regio;
                hc->HFC_inw = HFC_inw_regio;
                hc->HFC_wait = HFC_wait_regio;
                hc->read_fifo = read_fifo_regio;
                hc->write_fifo = write_fifo_regio;
                hc->pci_iobase = (u_int) hc->pci_dev->resource[0].start;
                if (!hc->pci_iobase) {
                        printk(KERN_WARNING
                               "HFC-multi: No IO for PCI card found\n");
                        pci_disable_device(hc->pci_dev);
                        return -EIO;
                }

                if (!request_region(hc->pci_iobase, 8, "hfcmulti")) {
                        printk(KERN_WARNING "HFC-multi: failed to request "
                               "address space at 0x%08lx (internal error)\n",
                               hc->pci_iobase);
                        pci_disable_device(hc->pci_dev);
                        return -EIO;
                }

                printk(KERN_INFO
                       "%s %s: defined at IOBASE %#x IRQ %d HZ %d leds-type %d\n",
                       m->vendor_name, m->card_name, (u_int) hc->pci_iobase,
                       hc->pci_dev->irq, HZ, hc->leds);
                pci_write_config_word(hc->pci_dev, PCI_COMMAND, PCI_ENA_REGIO);
                break;
        default:
                printk(KERN_WARNING "HFC-multi: Invalid IO mode.\n");
                pci_disable_device(hc->pci_dev);
                return -EIO;
        }

        pci_set_drvdata(hc->pci_dev, hc);

        /* At this point the needed PCI config is done */
        /* fifos are still not enabled */
        return 0;
}


/*
 * remove port
 */

static void
release_port(struct hfc_multi *hc, struct dchannel *dch)
{
        int     pt, ci, i = 0;
        u_long  flags;
        struct bchannel *pb;

        ci = dch->slot;
        pt = hc->chan[ci].port;

        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: entered for port %d\n",
                       __func__, pt + 1);

        if (pt >= hc->ports) {
                printk(KERN_WARNING "%s: ERROR port out of range (%d).\n",
                       __func__, pt + 1);
                return;
        }

        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: releasing port=%d\n",
                       __func__, pt + 1);

        if (dch->dev.D.protocol == ISDN_P_TE_S0)
                l1_event(dch->l1, CLOSE_CHANNEL);

        hc->chan[ci].dch = NULL;

        if (hc->created[pt]) {
                hc->created[pt] = 0;
                mISDN_unregister_device(&dch->dev);
        }

        spin_lock_irqsave(&hc->lock, flags);

        if (dch->timer.function) {
                timer_delete(&dch->timer);
                dch->timer.function = NULL;
        }

        if (hc->ctype == HFC_TYPE_E1) { /* E1 */
                /* remove sync */
                if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                        hc->syncronized = 0;
                        plxsd_checksync(hc, 1);
                }
                /* free channels */
                for (i = 0; i <= 31; i++) {
                        if (!((1 << i) & hc->bmask[pt])) /* skip unused chan */
                                continue;
                        if (hc->chan[i].bch) {
                                if (debug & DEBUG_HFCMULTI_INIT)
                                        printk(KERN_DEBUG
                                               "%s: free port %d channel %d\n",
                                               __func__, hc->chan[i].port + 1, i);
                                pb = hc->chan[i].bch;
                                hc->chan[i].bch = NULL;
                                spin_unlock_irqrestore(&hc->lock, flags);
                                mISDN_freebchannel(pb);
                                kfree(pb);
                                kfree(hc->chan[i].coeff);
                                spin_lock_irqsave(&hc->lock, flags);
                        }
                }
        } else {
                /* remove sync */
                if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
                        hc->syncronized &=
                                ~(1 << hc->chan[ci].port);
                        plxsd_checksync(hc, 1);
                }
                /* free channels */
                if (hc->chan[ci - 2].bch) {
                        if (debug & DEBUG_HFCMULTI_INIT)
                                printk(KERN_DEBUG
                                       "%s: free port %d channel %d\n",
                                       __func__, hc->chan[ci - 2].port + 1,
                                       ci - 2);
                        pb = hc->chan[ci - 2].bch;
                        hc->chan[ci - 2].bch = NULL;
                        spin_unlock_irqrestore(&hc->lock, flags);
                        mISDN_freebchannel(pb);
                        kfree(pb);
                        kfree(hc->chan[ci - 2].coeff);
                        spin_lock_irqsave(&hc->lock, flags);
                }
                if (hc->chan[ci - 1].bch) {
                        if (debug & DEBUG_HFCMULTI_INIT)
                                printk(KERN_DEBUG
                                       "%s: free port %d channel %d\n",
                                       __func__, hc->chan[ci - 1].port + 1,
                                       ci - 1);
                        pb = hc->chan[ci - 1].bch;
                        hc->chan[ci - 1].bch = NULL;
                        spin_unlock_irqrestore(&hc->lock, flags);
                        mISDN_freebchannel(pb);
                        kfree(pb);
                        kfree(hc->chan[ci - 1].coeff);
                        spin_lock_irqsave(&hc->lock, flags);
                }
        }

        spin_unlock_irqrestore(&hc->lock, flags);

        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: free port %d channel D(%d)\n", __func__,
                        pt+1, ci);
        mISDN_freedchannel(dch);
        kfree(dch);

        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: done!\n", __func__);
}

static void
release_card(struct hfc_multi *hc)
{
        u_long  flags;
        int     ch;

        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: release card (%d) entered\n",
                       __func__, hc->id);

        /* unregister clock source */
        if (hc->iclock)
                mISDN_unregister_clock(hc->iclock);

        /* disable and free irq */
        spin_lock_irqsave(&hc->lock, flags);
        disable_hwirq(hc);
        spin_unlock_irqrestore(&hc->lock, flags);
        udelay(1000);
        if (hc->irq) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: free irq %d (hc=%p)\n",
                            __func__, hc->irq, hc);
                free_irq(hc->irq, hc);
                hc->irq = 0;

        }

        /* disable D-channels & B-channels */
        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: disable all channels (d and b)\n",
                       __func__);
        for (ch = 0; ch <= 31; ch++) {
                if (hc->chan[ch].dch)
                        release_port(hc, hc->chan[ch].dch);
        }

        /* dimm leds */
        if (hc->leds)
                hfcmulti_leds(hc);

        /* release hardware */
        release_io_hfcmulti(hc);

        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: remove instance from list\n",
                       __func__);
        list_del(&hc->list);

        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: delete instance\n", __func__);
        if (hc == syncmaster)
                syncmaster = NULL;
        kfree(hc);
        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: card successfully removed\n",
                       __func__);
}

static void
init_e1_port_hw(struct hfc_multi *hc, struct hm_map *m)
{
        /* set optical line type */
        if (port[Port_cnt] & 0x001) {
                if (!m->opticalsupport)  {
                        printk(KERN_INFO
                               "This board has no optical "
                               "support\n");
                } else {
                        if (debug & DEBUG_HFCMULTI_INIT)
                                printk(KERN_DEBUG
                                       "%s: PORT set optical "
                                       "interface: card(%d) "
                                       "port(%d)\n",
                                       __func__,
                                       HFC_cnt + 1, 1);
                        test_and_set_bit(HFC_CFG_OPTICAL,
                            &hc->chan[hc->dnum[0]].cfg);
                }
        }
        /* set LOS report */
        if (port[Port_cnt] & 0x004) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: PORT set "
                               "LOS report: card(%d) port(%d)\n",
                               __func__, HFC_cnt + 1, 1);
                test_and_set_bit(HFC_CFG_REPORT_LOS,
                    &hc->chan[hc->dnum[0]].cfg);
        }
        /* set AIS report */
        if (port[Port_cnt] & 0x008) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: PORT set "
                               "AIS report: card(%d) port(%d)\n",
                               __func__, HFC_cnt + 1, 1);
                test_and_set_bit(HFC_CFG_REPORT_AIS,
                    &hc->chan[hc->dnum[0]].cfg);
        }
        /* set SLIP report */
        if (port[Port_cnt] & 0x010) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG
                               "%s: PORT set SLIP report: "
                               "card(%d) port(%d)\n",
                               __func__, HFC_cnt + 1, 1);
                test_and_set_bit(HFC_CFG_REPORT_SLIP,
                    &hc->chan[hc->dnum[0]].cfg);
        }
        /* set RDI report */
        if (port[Port_cnt] & 0x020) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG
                               "%s: PORT set RDI report: "
                               "card(%d) port(%d)\n",
                               __func__, HFC_cnt + 1, 1);
                test_and_set_bit(HFC_CFG_REPORT_RDI,
                    &hc->chan[hc->dnum[0]].cfg);
        }
        /* set CRC-4 Mode */
        if (!(port[Port_cnt] & 0x100)) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: PORT turn on CRC4 report:"
                               " card(%d) port(%d)\n",
                               __func__, HFC_cnt + 1, 1);
                test_and_set_bit(HFC_CFG_CRC4,
                    &hc->chan[hc->dnum[0]].cfg);
        } else {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: PORT turn off CRC4"
                               " report: card(%d) port(%d)\n",
                               __func__, HFC_cnt + 1, 1);
        }
        /* set forced clock */
        if (port[Port_cnt] & 0x0200) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: PORT force getting clock from "
                               "E1: card(%d) port(%d)\n",
                               __func__, HFC_cnt + 1, 1);
                test_and_set_bit(HFC_CHIP_E1CLOCK_GET, &hc->chip);
        } else
                if (port[Port_cnt] & 0x0400) {
                        if (debug & DEBUG_HFCMULTI_INIT)
                                printk(KERN_DEBUG "%s: PORT force putting clock to "
                                       "E1: card(%d) port(%d)\n",
                                       __func__, HFC_cnt + 1, 1);
                        test_and_set_bit(HFC_CHIP_E1CLOCK_PUT, &hc->chip);
                }
        /* set JATT PLL */
        if (port[Port_cnt] & 0x0800) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG "%s: PORT disable JATT PLL on "
                               "E1: card(%d) port(%d)\n",
                               __func__, HFC_cnt + 1, 1);
                test_and_set_bit(HFC_CHIP_RX_SYNC, &hc->chip);
        }
        /* set elastic jitter buffer */
        if (port[Port_cnt] & 0x3000) {
                hc->chan[hc->dnum[0]].jitter = (port[Port_cnt]>>12) & 0x3;
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG
                               "%s: PORT set elastic "
                               "buffer to %d: card(%d) port(%d)\n",
                            __func__, hc->chan[hc->dnum[0]].jitter,
                               HFC_cnt + 1, 1);
        } else
                hc->chan[hc->dnum[0]].jitter = 2; /* default */
}

static int
init_e1_port(struct hfc_multi *hc, struct hm_map *m, int pt)
{
        struct dchannel *dch;
        struct bchannel *bch;
        int             ch, ret = 0;
        char            name[MISDN_MAX_IDLEN];
        int             bcount = 0;

        dch = kzalloc_obj(struct dchannel);
        if (!dch)
                return -ENOMEM;
        dch->debug = debug;
        mISDN_initdchannel(dch, MAX_DFRAME_LEN_L1, ph_state_change);
        dch->hw = hc;
        dch->dev.Dprotocols = (1 << ISDN_P_TE_E1) | (1 << ISDN_P_NT_E1);
        dch->dev.Bprotocols = (1 << (ISDN_P_B_RAW & ISDN_P_B_MASK)) |
            (1 << (ISDN_P_B_HDLC & ISDN_P_B_MASK));
        dch->dev.D.send = handle_dmsg;
        dch->dev.D.ctrl = hfcm_dctrl;
        dch->slot = hc->dnum[pt];
        hc->chan[hc->dnum[pt]].dch = dch;
        hc->chan[hc->dnum[pt]].port = pt;
        hc->chan[hc->dnum[pt]].nt_timer = -1;
        for (ch = 1; ch <= 31; ch++) {
                if (!((1 << ch) & hc->bmask[pt])) /* skip unused channel */
                        continue;
                bch = kzalloc_obj(struct bchannel);
                if (!bch) {
                        printk(KERN_ERR "%s: no memory for bchannel\n",
                            __func__);
                        ret = -ENOMEM;
                        goto free_chan;
                }
                hc->chan[ch].coeff = kzalloc(512, GFP_KERNEL);
                if (!hc->chan[ch].coeff) {
                        printk(KERN_ERR "%s: no memory for coeffs\n",
                            __func__);
                        ret = -ENOMEM;
                        kfree(bch);
                        goto free_chan;
                }
                bch->nr = ch;
                bch->slot = ch;
                bch->debug = debug;
                mISDN_initbchannel(bch, MAX_DATA_MEM, poll >> 1);
                bch->hw = hc;
                bch->ch.send = handle_bmsg;
                bch->ch.ctrl = hfcm_bctrl;
                bch->ch.nr = ch;
                list_add(&bch->ch.list, &dch->dev.bchannels);
                hc->chan[ch].bch = bch;
                hc->chan[ch].port = pt;
                set_channelmap(bch->nr, dch->dev.channelmap);
                bcount++;
        }
        dch->dev.nrbchan = bcount;
        if (pt == 0)
                init_e1_port_hw(hc, m);
        if (hc->ports > 1)
                snprintf(name, MISDN_MAX_IDLEN - 1, "hfc-e1.%d-%d",
                                HFC_cnt + 1, pt+1);
        else
                snprintf(name, MISDN_MAX_IDLEN - 1, "hfc-e1.%d", HFC_cnt + 1);
        ret = mISDN_register_device(&dch->dev, &hc->pci_dev->dev, name);
        if (ret)
                goto free_chan;
        hc->created[pt] = 1;
        return ret;
free_chan:
        release_port(hc, dch);
        return ret;
}

static int
init_multi_port(struct hfc_multi *hc, int pt)
{
        struct dchannel *dch;
        struct bchannel *bch;
        int             ch, i, ret = 0;
        char            name[MISDN_MAX_IDLEN];

        dch = kzalloc_obj(struct dchannel);
        if (!dch)
                return -ENOMEM;
        dch->debug = debug;
        mISDN_initdchannel(dch, MAX_DFRAME_LEN_L1, ph_state_change);
        dch->hw = hc;
        dch->dev.Dprotocols = (1 << ISDN_P_TE_S0) | (1 << ISDN_P_NT_S0);
        dch->dev.Bprotocols = (1 << (ISDN_P_B_RAW & ISDN_P_B_MASK)) |
                (1 << (ISDN_P_B_HDLC & ISDN_P_B_MASK));
        dch->dev.D.send = handle_dmsg;
        dch->dev.D.ctrl = hfcm_dctrl;
        dch->dev.nrbchan = 2;
        i = pt << 2;
        dch->slot = i + 2;
        hc->chan[i + 2].dch = dch;
        hc->chan[i + 2].port = pt;
        hc->chan[i + 2].nt_timer = -1;
        for (ch = 0; ch < dch->dev.nrbchan; ch++) {
                bch = kzalloc_obj(struct bchannel);
                if (!bch) {
                        printk(KERN_ERR "%s: no memory for bchannel\n",
                               __func__);
                        ret = -ENOMEM;
                        goto free_chan;
                }
                hc->chan[i + ch].coeff = kzalloc(512, GFP_KERNEL);
                if (!hc->chan[i + ch].coeff) {
                        printk(KERN_ERR "%s: no memory for coeffs\n",
                               __func__);
                        ret = -ENOMEM;
                        kfree(bch);
                        goto free_chan;
                }
                bch->nr = ch + 1;
                bch->slot = i + ch;
                bch->debug = debug;
                mISDN_initbchannel(bch, MAX_DATA_MEM, poll >> 1);
                bch->hw = hc;
                bch->ch.send = handle_bmsg;
                bch->ch.ctrl = hfcm_bctrl;
                bch->ch.nr = ch + 1;
                list_add(&bch->ch.list, &dch->dev.bchannels);
                hc->chan[i + ch].bch = bch;
                hc->chan[i + ch].port = pt;
                set_channelmap(bch->nr, dch->dev.channelmap);
        }
        /* set master clock */
        if (port[Port_cnt] & 0x001) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG
                               "%s: PROTOCOL set master clock: "
                               "card(%d) port(%d)\n",
                               __func__, HFC_cnt + 1, pt + 1);
                if (dch->dev.D.protocol != ISDN_P_TE_S0) {
                        printk(KERN_ERR "Error: Master clock "
                               "for port(%d) of card(%d) is only"
                               " possible with TE-mode\n",
                               pt + 1, HFC_cnt + 1);
                        ret = -EINVAL;
                        goto free_chan;
                }
                if (hc->masterclk >= 0) {
                        printk(KERN_ERR "Error: Master clock "
                               "for port(%d) of card(%d) already "
                               "defined for port(%d)\n",
                               pt + 1, HFC_cnt + 1, hc->masterclk + 1);
                        ret = -EINVAL;
                        goto free_chan;
                }
                hc->masterclk = pt;
        }
        /* set transmitter line to non capacitive */
        if (port[Port_cnt] & 0x002) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG
                               "%s: PROTOCOL set non capacitive "
                               "transmitter: card(%d) port(%d)\n",
                               __func__, HFC_cnt + 1, pt + 1);
                test_and_set_bit(HFC_CFG_NONCAP_TX,
                                 &hc->chan[i + 2].cfg);
        }
        /* disable E-channel */
        if (port[Port_cnt] & 0x004) {
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG
                               "%s: PROTOCOL disable E-channel: "
                               "card(%d) port(%d)\n",
                               __func__, HFC_cnt + 1, pt + 1);
                test_and_set_bit(HFC_CFG_DIS_ECHANNEL,
                                 &hc->chan[i + 2].cfg);
        }
        if (hc->ctype == HFC_TYPE_XHFC) {
                snprintf(name, MISDN_MAX_IDLEN - 1, "xhfc.%d-%d",
                         HFC_cnt + 1, pt + 1);
                ret = mISDN_register_device(&dch->dev, NULL, name);
        } else {
                snprintf(name, MISDN_MAX_IDLEN - 1, "hfc-%ds.%d-%d",
                         hc->ctype, HFC_cnt + 1, pt + 1);
                ret = mISDN_register_device(&dch->dev, &hc->pci_dev->dev, name);
        }
        if (ret)
                goto free_chan;
        hc->created[pt] = 1;
        return ret;
free_chan:
        release_port(hc, dch);
        return ret;
}

static int
hfcmulti_init(struct hm_map *m, struct pci_dev *pdev,
              const struct pci_device_id *ent)
{
        int             ret_err = 0;
        int             pt;
        struct hfc_multi        *hc;
        u_long          flags;
        u_char          dips = 0, pmj = 0; /* dip settings, port mode Jumpers */
        int             i, ch;
        u_int           maskcheck;

        if (HFC_cnt >= MAX_CARDS) {
                printk(KERN_ERR "too many cards (max=%d).\n",
                       MAX_CARDS);
                return -EINVAL;
        }
        if ((type[HFC_cnt] & 0xff) && (type[HFC_cnt] & 0xff) != m->type) {
                printk(KERN_WARNING "HFC-MULTI: Card '%s:%s' type %d found but "
                       "type[%d] %d was supplied as module parameter\n",
                       m->vendor_name, m->card_name, m->type, HFC_cnt,
                       type[HFC_cnt] & 0xff);
                printk(KERN_WARNING "HFC-MULTI: Load module without parameters "
                       "first, to see cards and their types.");
                return -EINVAL;
        }
        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: Registering %s:%s chip type %d (0x%x)\n",
                       __func__, m->vendor_name, m->card_name, m->type,
                       type[HFC_cnt]);

        /* allocate card+fifo structure */
        hc = kzalloc_obj(struct hfc_multi);
        if (!hc) {
                printk(KERN_ERR "No kmem for HFC-Multi card\n");
                return -ENOMEM;
        }
        spin_lock_init(&hc->lock);
        hc->mtyp = m;
        hc->ctype =  m->type;
        hc->ports = m->ports;
        hc->id = HFC_cnt;
        hc->pcm = pcm[HFC_cnt];
        hc->io_mode = iomode[HFC_cnt];
        if (hc->ctype == HFC_TYPE_E1 && dmask[E1_cnt]) {
                /* fragment card */
                pt = 0;
                maskcheck = 0;
                for (ch = 0; ch <= 31; ch++) {
                        if (!((1 << ch) & dmask[E1_cnt]))
                                continue;
                        hc->dnum[pt] = ch;
                        hc->bmask[pt] = bmask[bmask_cnt++];
                        if ((maskcheck & hc->bmask[pt])
                         || (dmask[E1_cnt] & hc->bmask[pt])) {
                                printk(KERN_INFO
                                       "HFC-E1 #%d has overlapping B-channels on fragment #%d\n",
                                       E1_cnt + 1, pt);
                                kfree(hc);
                                return -EINVAL;
                        }
                        maskcheck |= hc->bmask[pt];
                        printk(KERN_INFO
                               "HFC-E1 #%d uses D-channel on slot %d and a B-channel map of 0x%08x\n",
                                E1_cnt + 1, ch, hc->bmask[pt]);
                        pt++;
                }
                hc->ports = pt;
        }
        if (hc->ctype == HFC_TYPE_E1 && !dmask[E1_cnt]) {
                /* default card layout */
                hc->dnum[0] = 16;
                hc->bmask[0] = 0xfffefffe;
                hc->ports = 1;
        }

        /* set chip specific features */
        hc->masterclk = -1;
        if (type[HFC_cnt] & 0x100) {
                test_and_set_bit(HFC_CHIP_ULAW, &hc->chip);
                hc->silence = 0xff; /* ulaw silence */
        } else
                hc->silence = 0x2a; /* alaw silence */
        if ((poll >> 1) > sizeof(hc->silence_data)) {
                printk(KERN_ERR "HFCMULTI error: silence_data too small, "
                       "please fix\n");
                kfree(hc);
                return -EINVAL;
        }
        for (i = 0; i < (poll >> 1); i++)
                hc->silence_data[i] = hc->silence;

        if (hc->ctype != HFC_TYPE_XHFC) {
                if (!(type[HFC_cnt] & 0x200))
                        test_and_set_bit(HFC_CHIP_DTMF, &hc->chip);
                test_and_set_bit(HFC_CHIP_CONF, &hc->chip);
        }

        if (type[HFC_cnt] & 0x800)
                test_and_set_bit(HFC_CHIP_PCM_SLAVE, &hc->chip);
        if (type[HFC_cnt] & 0x1000) {
                test_and_set_bit(HFC_CHIP_PCM_MASTER, &hc->chip);
                test_and_clear_bit(HFC_CHIP_PCM_SLAVE, &hc->chip);
        }
        if (type[HFC_cnt] & 0x4000)
                test_and_set_bit(HFC_CHIP_EXRAM_128, &hc->chip);
        if (type[HFC_cnt] & 0x8000)
                test_and_set_bit(HFC_CHIP_EXRAM_512, &hc->chip);
        hc->slots = 32;
        if (type[HFC_cnt] & 0x10000)
                hc->slots = 64;
        if (type[HFC_cnt] & 0x20000)
                hc->slots = 128;
        if (type[HFC_cnt] & 0x80000) {
                test_and_set_bit(HFC_CHIP_WATCHDOG, &hc->chip);
                hc->wdcount = 0;
                hc->wdbyte = V_GPIO_OUT2;
                printk(KERN_NOTICE "Watchdog enabled\n");
        }

        if (pdev && ent)
                /* setup pci, hc->slots may change due to PLXSD */
                ret_err = setup_pci(hc, pdev, ent);
        else
#ifdef CONFIG_MISDN_HFCMULTI_8xx
                ret_err = setup_embedded(hc, m);
#else
        {
                printk(KERN_WARNING "Embedded IO Mode not selected\n");
                ret_err = -EIO;
        }
#endif
        if (ret_err) {
                if (hc == syncmaster)
                        syncmaster = NULL;
                kfree(hc);
                return ret_err;
        }

        hc->HFC_outb_nodebug = hc->HFC_outb;
        hc->HFC_inb_nodebug = hc->HFC_inb;
        hc->HFC_inw_nodebug = hc->HFC_inw;
        hc->HFC_wait_nodebug = hc->HFC_wait;
#ifdef HFC_REGISTER_DEBUG
        hc->HFC_outb = HFC_outb_debug;
        hc->HFC_inb = HFC_inb_debug;
        hc->HFC_inw = HFC_inw_debug;
        hc->HFC_wait = HFC_wait_debug;
#endif
        /* create channels */
        for (pt = 0; pt < hc->ports; pt++) {
                if (Port_cnt >= MAX_PORTS) {
                        printk(KERN_ERR "too many ports (max=%d).\n",
                               MAX_PORTS);
                        ret_err = -EINVAL;
                        goto free_card;
                }
                if (hc->ctype == HFC_TYPE_E1)
                        ret_err = init_e1_port(hc, m, pt);
                else
                        ret_err = init_multi_port(hc, pt);
                if (debug & DEBUG_HFCMULTI_INIT)
                        printk(KERN_DEBUG
                            "%s: Registering D-channel, card(%d) port(%d) "
                               "result %d\n",
                            __func__, HFC_cnt + 1, pt + 1, ret_err);

                if (ret_err) {
                        while (pt) { /* release already registered ports */
                                pt--;
                                if (hc->ctype == HFC_TYPE_E1)
                                        release_port(hc,
                                                hc->chan[hc->dnum[pt]].dch);
                                else
                                        release_port(hc,
                                                hc->chan[(pt << 2) + 2].dch);
                        }
                        goto free_card;
                }
                if (hc->ctype != HFC_TYPE_E1)
                        Port_cnt++; /* for each S0 port */
        }
        if (hc->ctype == HFC_TYPE_E1) {
                Port_cnt++; /* for each E1 port */
                E1_cnt++;
        }

        /* disp switches */
        switch (m->dip_type) {
        case DIP_4S:
                /*
                 * Get DIP setting for beroNet 1S/2S/4S cards
                 * DIP Setting: (collect GPIO 13/14/15 (R_GPIO_IN1) +
                 * GPI 19/23 (R_GPI_IN2))
                 */
                dips = ((~HFC_inb(hc, R_GPIO_IN1) & 0xE0) >> 5) |
                        ((~HFC_inb(hc, R_GPI_IN2) & 0x80) >> 3) |
                        (~HFC_inb(hc, R_GPI_IN2) & 0x08);

                /* Port mode (TE/NT) jumpers */
                pmj = ((HFC_inb(hc, R_GPI_IN3) >> 4)  & 0xf);

                if (test_bit(HFC_CHIP_B410P, &hc->chip))
                        pmj = ~pmj & 0xf;

                printk(KERN_INFO "%s: %s DIPs(0x%x) jumpers(0x%x)\n",
                       m->vendor_name, m->card_name, dips, pmj);
                break;
        case DIP_8S:
                /*
                 * Get DIP Setting for beroNet 8S0+ cards
                 * Enable PCI auxbridge function
                 */
                HFC_outb(hc, R_BRG_PCM_CFG, 1 | V_PCM_CLK);
                /* prepare access to auxport */
                outw(0x4000, hc->pci_iobase + 4);
                /*
                 * some dummy reads are required to
                 * read valid DIP switch data
                 */
                dips = inb(hc->pci_iobase);
                dips = inb(hc->pci_iobase);
                dips = inb(hc->pci_iobase);
                dips = ~inb(hc->pci_iobase) & 0x3F;
                outw(0x0, hc->pci_iobase + 4);
                /* disable PCI auxbridge function */
                HFC_outb(hc, R_BRG_PCM_CFG, V_PCM_CLK);
                printk(KERN_INFO "%s: %s DIPs(0x%x)\n",
                       m->vendor_name, m->card_name, dips);
                break;
        case DIP_E1:
                /*
                 * get DIP Setting for beroNet E1 cards
                 * DIP Setting: collect GPI 4/5/6/7 (R_GPI_IN0)
                 */
                dips = (~HFC_inb(hc, R_GPI_IN0) & 0xF0) >> 4;
                printk(KERN_INFO "%s: %s DIPs(0x%x)\n",
                       m->vendor_name, m->card_name, dips);
                break;
        }

        /* add to list */
        spin_lock_irqsave(&HFClock, flags);
        list_add_tail(&hc->list, &HFClist);
        spin_unlock_irqrestore(&HFClock, flags);

        /* use as clock source */
        if (clock == HFC_cnt + 1)
                hc->iclock = mISDN_register_clock("HFCMulti", 0, clockctl, hc);

        /* initialize hardware */
        hc->irq = (m->irq) ? : hc->pci_dev->irq;
        ret_err = init_card(hc);
        if (ret_err) {
                printk(KERN_ERR "init card returns %d\n", ret_err);
                release_card(hc);
                return ret_err;
        }

        /* start IRQ and return */
        spin_lock_irqsave(&hc->lock, flags);
        enable_hwirq(hc);
        spin_unlock_irqrestore(&hc->lock, flags);
        return 0;

free_card:
        release_io_hfcmulti(hc);
        if (hc == syncmaster)
                syncmaster = NULL;
        kfree(hc);
        return ret_err;
}

static void hfc_remove_pci(struct pci_dev *pdev)
{
        struct hfc_multi        *card = pci_get_drvdata(pdev);
        u_long                  flags;

        if (debug)
                printk(KERN_INFO "removing hfc_multi card vendor:%x "
                       "device:%x subvendor:%x subdevice:%x\n",
                       pdev->vendor, pdev->device,
                       pdev->subsystem_vendor, pdev->subsystem_device);

        if (card) {
                spin_lock_irqsave(&HFClock, flags);
                release_card(card);
                spin_unlock_irqrestore(&HFClock, flags);
        }  else {
                if (debug)
                        printk(KERN_DEBUG "%s: drvdata already removed\n",
                               __func__);
        }
}

#define VENDOR_CCD      "Cologne Chip AG"
#define VENDOR_BN       "beroNet GmbH"
#define VENDOR_DIG      "Digium Inc."
#define VENDOR_JH       "Junghanns.NET GmbH"
#define VENDOR_PRIM     "PrimuX"

static const struct hm_map hfcm_map[] = {
        /*0*/   {VENDOR_BN, "HFC-1S Card (mini PCI)", 4, 1, 1, 3, 0, DIP_4S, 0, 0},
        /*1*/   {VENDOR_BN, "HFC-2S Card", 4, 2, 1, 3, 0, DIP_4S, 0, 0},
        /*2*/   {VENDOR_BN, "HFC-2S Card (mini PCI)", 4, 2, 1, 3, 0, DIP_4S, 0, 0},
        /*3*/   {VENDOR_BN, "HFC-4S Card", 4, 4, 1, 2, 0, DIP_4S, 0, 0},
        /*4*/   {VENDOR_BN, "HFC-4S Card (mini PCI)", 4, 4, 1, 2, 0, 0, 0, 0},
        /*5*/   {VENDOR_CCD, "HFC-4S Eval (old)", 4, 4, 0, 0, 0, 0, 0, 0},
        /*6*/   {VENDOR_CCD, "HFC-4S IOB4ST", 4, 4, 1, 2, 0, DIP_4S, 0, 0},
        /*7*/   {VENDOR_CCD, "HFC-4S", 4, 4, 1, 2, 0, 0, 0, 0},
        /*8*/   {VENDOR_DIG, "HFC-4S Card", 4, 4, 0, 2, 0, 0, HFC_IO_MODE_REGIO, 0},
        /*9*/   {VENDOR_CCD, "HFC-4S Swyx 4xS0 SX2 QuadBri", 4, 4, 1, 2, 0, 0, 0, 0},
        /*10*/  {VENDOR_JH, "HFC-4S (junghanns 2.0)", 4, 4, 1, 2, 0, 0, 0, 0},
        /*11*/  {VENDOR_PRIM, "HFC-2S Primux Card", 4, 2, 0, 0, 0, 0, 0, 0},

        /*12*/  {VENDOR_BN, "HFC-8S Card", 8, 8, 1, 0, 0, 0, 0, 0},
        /*13*/  {VENDOR_BN, "HFC-8S Card (+)", 8, 8, 1, 8, 0, DIP_8S,
                 HFC_IO_MODE_REGIO, 0},
        /*14*/  {VENDOR_CCD, "HFC-8S Eval (old)", 8, 8, 0, 0, 0, 0, 0, 0},
        /*15*/  {VENDOR_CCD, "HFC-8S IOB4ST Recording", 8, 8, 1, 0, 0, 0, 0, 0},

        /*16*/  {VENDOR_CCD, "HFC-8S IOB8ST", 8, 8, 1, 0, 0, 0, 0, 0},
        /*17*/  {VENDOR_CCD, "HFC-8S", 8, 8, 1, 0, 0, 0, 0, 0},
        /*18*/  {VENDOR_CCD, "HFC-8S", 8, 8, 1, 0, 0, 0, 0, 0},

        /*19*/  {VENDOR_BN, "HFC-E1 Card", 1, 1, 0, 1, 0, DIP_E1, 0, 0},
        /*20*/  {VENDOR_BN, "HFC-E1 Card (mini PCI)", 1, 1, 0, 1, 0, 0, 0, 0},
        /*21*/  {VENDOR_BN, "HFC-E1+ Card (Dual)", 1, 1, 0, 1, 0, DIP_E1, 0, 0},
        /*22*/  {VENDOR_BN, "HFC-E1 Card (Dual)", 1, 1, 0, 1, 0, DIP_E1, 0, 0},

        /*23*/  {VENDOR_CCD, "HFC-E1 Eval (old)", 1, 1, 0, 0, 0, 0, 0, 0},
        /*24*/  {VENDOR_CCD, "HFC-E1 IOB1E1", 1, 1, 0, 1, 0, 0, 0, 0},
        /*25*/  {VENDOR_CCD, "HFC-E1", 1, 1, 0, 1, 0, 0, 0, 0},

        /*26*/  {VENDOR_CCD, "HFC-4S Speech Design", 4, 4, 0, 0, 0, 0,
                 HFC_IO_MODE_PLXSD, 0},
        /*27*/  {VENDOR_CCD, "HFC-E1 Speech Design", 1, 1, 0, 0, 0, 0,
                 HFC_IO_MODE_PLXSD, 0},
        /*28*/  {VENDOR_CCD, "HFC-4S OpenVox", 4, 4, 1, 0, 0, 0, 0, 0},
        /*29*/  {VENDOR_CCD, "HFC-2S OpenVox", 4, 2, 1, 0, 0, 0, 0, 0},
        /*30*/  {VENDOR_CCD, "HFC-8S OpenVox", 8, 8, 1, 0, 0, 0, 0, 0},
        /*31*/  {VENDOR_CCD, "XHFC-4S Speech Design", 5, 4, 0, 0, 0, 0,
                 HFC_IO_MODE_EMBSD, XHFC_IRQ},
        /*32*/  {VENDOR_JH, "HFC-8S (junghanns)", 8, 8, 1, 0, 0, 0, 0, 0},
        /*33*/  {VENDOR_BN, "HFC-2S Beronet Card PCIe", 4, 2, 1, 3, 0, DIP_4S, 0, 0},
        /*34*/  {VENDOR_BN, "HFC-4S Beronet Card PCIe", 4, 4, 1, 2, 0, DIP_4S, 0, 0},
};

#undef H
#define H(x)    ((unsigned long)&hfcm_map[x])
static const struct pci_device_id hfmultipci_ids[] = {

        /* Cards with HFC-4S Chip */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_BN1SM, 0, 0, H(0)}, /* BN1S mini PCI */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_BN2S, 0, 0, H(1)}, /* BN2S */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_BN2SM, 0, 0, H(2)}, /* BN2S mini PCI */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_BN4S, 0, 0, H(3)}, /* BN4S */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_BN4SM, 0, 0, H(4)}, /* BN4S mini PCI */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
          PCI_DEVICE_ID_CCD_HFC4S, 0, 0, H(5)}, /* Old Eval */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_IOB4ST, 0, 0, H(6)}, /* IOB4ST */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_HFC4S, 0, 0, H(7)}, /* 4S */
        { PCI_VENDOR_ID_DIGIUM, PCI_DEVICE_ID_DIGIUM_HFC4S,
          PCI_VENDOR_ID_DIGIUM, PCI_DEVICE_ID_DIGIUM_HFC4S, 0, 0, H(8)},
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_SWYX4S, 0, 0, H(9)}, /* 4S Swyx */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_JH4S20, 0, 0, H(10)},
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_PMX2S, 0, 0, H(11)}, /* Primux */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_OV4S, 0, 0, H(28)}, /* OpenVox 4 */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_OV2S, 0, 0, H(29)}, /* OpenVox 2 */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
          0xb761, 0, 0, H(33)}, /* BN2S PCIe */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
          0xb762, 0, 0, H(34)}, /* BN4S PCIe */

        /* Cards with HFC-8S Chip */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_BN8S, 0, 0, H(12)}, /* BN8S */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_BN8SP, 0, 0, H(13)}, /* BN8S+ */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
          PCI_DEVICE_ID_CCD_HFC8S, 0, 0, H(14)}, /* old Eval */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_IOB8STR, 0, 0, H(15)}, /* IOB8ST Recording */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_IOB8ST, 0, 0, H(16)}, /* IOB8ST  */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_IOB8ST_1, 0, 0, H(17)}, /* IOB8ST  */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_HFC8S, 0, 0, H(18)}, /* 8S */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_OV8S, 0, 0, H(30)}, /* OpenVox 8 */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_JH8S, 0, 0, H(32)}, /* Junganns 8S  */


        /* Cards with HFC-E1 Chip */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_BNE1, 0, 0, H(19)}, /* BNE1 */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_BNE1M, 0, 0, H(20)}, /* BNE1 mini PCI */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_BNE1DP, 0, 0, H(21)}, /* BNE1 + (Dual) */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_BNE1D, 0, 0, H(22)}, /* BNE1 (Dual) */

        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD,
          PCI_DEVICE_ID_CCD_HFCE1, 0, 0, H(23)}, /* Old Eval */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_IOB1E1, 0, 0, H(24)}, /* IOB1E1 */
        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_HFCE1, 0, 0, H(25)}, /* E1 */

        { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_SPD4S, 0, 0, H(26)}, /* PLX PCI Bridge */
        { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_SPDE1, 0, 0, H(27)}, /* PLX PCI Bridge */

        { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD,
          PCI_SUBDEVICE_ID_CCD_JHSE1, 0, 0, H(25)}, /* Junghanns E1 */

        { PCI_VDEVICE(CCD, PCI_DEVICE_ID_CCD_HFC4S), 0 },
        { PCI_VDEVICE(CCD, PCI_DEVICE_ID_CCD_HFC8S), 0 },
        { PCI_VDEVICE(CCD, PCI_DEVICE_ID_CCD_HFCE1), 0 },
        {0, }
};
#undef H

MODULE_DEVICE_TABLE(pci, hfmultipci_ids);

static int
hfcmulti_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
{
        struct hm_map   *m = (struct hm_map *)ent->driver_data;
        int             ret;

        if (m == NULL && ent->vendor == PCI_VENDOR_ID_CCD && (
                    ent->device == PCI_DEVICE_ID_CCD_HFC4S ||
                    ent->device == PCI_DEVICE_ID_CCD_HFC8S ||
                    ent->device == PCI_DEVICE_ID_CCD_HFCE1)) {
                printk(KERN_ERR
                       "Unknown HFC multiport controller (vendor:%04x device:%04x "
                       "subvendor:%04x subdevice:%04x)\n", pdev->vendor,
                       pdev->device, pdev->subsystem_vendor,
                       pdev->subsystem_device);
                printk(KERN_ERR
                       "Please contact the driver maintainer for support.\n");
                return -ENODEV;
        }
        ret = hfcmulti_init(m, pdev, ent);
        if (ret)
                return ret;
        HFC_cnt++;
        printk(KERN_INFO "%d devices registered\n", HFC_cnt);
        return 0;
}

static struct pci_driver hfcmultipci_driver = {
        .name           = "hfc_multi",
        .probe          = hfcmulti_probe,
        .remove         = hfc_remove_pci,
        .id_table       = hfmultipci_ids,
};

static void __exit
HFCmulti_cleanup(void)
{
        struct hfc_multi *card, *next;

        /* get rid of all devices of this driver */
        list_for_each_entry_safe(card, next, &HFClist, list)
                release_card(card);
        pci_unregister_driver(&hfcmultipci_driver);
}

static int __init
HFCmulti_init(void)
{
        int err;
        int i, xhfc = 0;
        struct hm_map m;

        printk(KERN_INFO "mISDN: HFC-multi driver %s\n", HFC_MULTI_VERSION);

#ifdef IRQ_DEBUG
        printk(KERN_DEBUG "%s: IRQ_DEBUG IS ENABLED!\n", __func__);
#endif

        if (debug & DEBUG_HFCMULTI_INIT)
                printk(KERN_DEBUG "%s: init entered\n", __func__);

        switch (poll) {
        case 0:
                poll_timer = 6;
                poll = 128;
                break;
        case 8:
                poll_timer = 2;
                break;
        case 16:
                poll_timer = 3;
                break;
        case 32:
                poll_timer = 4;
                break;
        case 64:
                poll_timer = 5;
                break;
        case 128:
                poll_timer = 6;
                break;
        case 256:
                poll_timer = 7;
                break;
        default:
                printk(KERN_ERR
                       "%s: Wrong poll value (%d).\n", __func__, poll);
                err = -EINVAL;
                return err;

        }

        if (!clock)
                clock = 1;

        /* Register the embedded devices.
         * This should be done before the PCI cards registration */
        switch (hwid) {
        case HWID_MINIP4:
                xhfc = 1;
                m = hfcm_map[31];
                break;
        case HWID_MINIP8:
                xhfc = 2;
                m = hfcm_map[31];
                break;
        case HWID_MINIP16:
                xhfc = 4;
                m = hfcm_map[31];
                break;
        default:
                xhfc = 0;
        }

        for (i = 0; i < xhfc; ++i) {
                err = hfcmulti_init(&m, NULL, NULL);
                if (err) {
                        printk(KERN_ERR "error registering embedded driver: "
                               "%x\n", err);
                        return err;
                }
                HFC_cnt++;
                printk(KERN_INFO "%d devices registered\n", HFC_cnt);
        }

        /* Register the PCI cards */
        err = pci_register_driver(&hfcmultipci_driver);
        if (err < 0) {
                printk(KERN_ERR "error registering pci driver: %x\n", err);
                return err;
        }

        return 0;
}


module_init(HFCmulti_init);
module_exit(HFCmulti_cleanup);