// SPDX-License-Identifier: GPL-2.0-only
/*
 * Linux device driver for RTL8187
 *
 * Copyright 2007 Michael Wu <flamingice@sourmilk.net>
 * Copyright 2007 Andrea Merello <andrea.merello@gmail.com>
 *
 * Based on the r8187 driver, which is:
 * Copyright 2005 Andrea Merello <andrea.merello@gmail.com>, et al.
 *
 * The driver was extended to the RTL8187B in 2008 by:
 *      Herton Ronaldo Krzesinski <herton@mandriva.com.br>
 *      Hin-Tak Leung <htl10@users.sourceforge.net>
 *      Larry Finger <Larry.Finger@lwfinger.net>
 *
 * Magic delays and register offsets below are taken from the original
 * r8187 driver sources.  Thanks to Realtek for their support!
 */

#include <linux/usb.h>
#include <linux/slab.h>
#include <linux/delay.h>
#include <linux/etherdevice.h>
#include <linux/eeprom_93cx6.h>
#include <linux/module.h>
#include <net/mac80211.h>

#include "rtl8187.h"
#include "rtl8225.h"
#ifdef CONFIG_RTL8187_LEDS
#include "leds.h"
#endif
#include "rfkill.h"

MODULE_AUTHOR("Michael Wu <flamingice@sourmilk.net>");
MODULE_AUTHOR("Andrea Merello <andrea.merello@gmail.com>");
MODULE_AUTHOR("Herton Ronaldo Krzesinski <herton@mandriva.com.br>");
MODULE_AUTHOR("Hin-Tak Leung <htl10@users.sourceforge.net>");
MODULE_AUTHOR("Larry Finger <Larry.Finger@lwfinger.net>");
MODULE_DESCRIPTION("RTL8187/RTL8187B USB wireless driver");
MODULE_LICENSE("GPL");

static const struct usb_device_id rtl8187_table[] = {
        /* Asus */
        {USB_DEVICE(0x0b05, 0x171d), .driver_info = DEVICE_RTL8187},
        /* Belkin */
        {USB_DEVICE(0x050d, 0x705e), .driver_info = DEVICE_RTL8187B},
        /* Realtek */
        {USB_DEVICE(0x0bda, 0x8187), .driver_info = DEVICE_RTL8187},
        {USB_DEVICE(0x0bda, 0x8189), .driver_info = DEVICE_RTL8187B},
        {USB_DEVICE(0x0bda, 0x8197), .driver_info = DEVICE_RTL8187B},
        {USB_DEVICE(0x0bda, 0x8198), .driver_info = DEVICE_RTL8187B},
        /* Surecom */
        {USB_DEVICE(0x0769, 0x11F2), .driver_info = DEVICE_RTL8187},
        /* Logitech */
        {USB_DEVICE(0x0789, 0x010C), .driver_info = DEVICE_RTL8187},
        /* Netgear */
        {USB_DEVICE(0x0846, 0x6100), .driver_info = DEVICE_RTL8187},
        {USB_DEVICE(0x0846, 0x6a00), .driver_info = DEVICE_RTL8187},
        {USB_DEVICE(0x0846, 0x4260), .driver_info = DEVICE_RTL8187B},
        /* HP */
        {USB_DEVICE(0x03f0, 0xca02), .driver_info = DEVICE_RTL8187},
        /* Sitecom */
        {USB_DEVICE(0x0df6, 0x000d), .driver_info = DEVICE_RTL8187},
        {USB_DEVICE(0x0df6, 0x0028), .driver_info = DEVICE_RTL8187B},
        {USB_DEVICE(0x0df6, 0x0029), .driver_info = DEVICE_RTL8187B},
        /* Sphairon Access Systems GmbH */
        {USB_DEVICE(0x114B, 0x0150), .driver_info = DEVICE_RTL8187},
        /* Dick Smith Electronics */
        {USB_DEVICE(0x1371, 0x9401), .driver_info = DEVICE_RTL8187},
        /* Abocom */
        {USB_DEVICE(0x13d1, 0xabe6), .driver_info = DEVICE_RTL8187},
        /* Qcom */
        {USB_DEVICE(0x18E8, 0x6232), .driver_info = DEVICE_RTL8187},
        /* AirLive */
        {USB_DEVICE(0x1b75, 0x8187), .driver_info = DEVICE_RTL8187},
        /* Linksys */
        {USB_DEVICE(0x1737, 0x0073), .driver_info = DEVICE_RTL8187B},
        {}
};

MODULE_DEVICE_TABLE(usb, rtl8187_table);

static const struct ieee80211_rate rtl818x_rates[] = {
        { .bitrate = 10, .hw_value = 0, },
        { .bitrate = 20, .hw_value = 1, },
        { .bitrate = 55, .hw_value = 2, },
        { .bitrate = 110, .hw_value = 3, },
        { .bitrate = 60, .hw_value = 4, },
        { .bitrate = 90, .hw_value = 5, },
        { .bitrate = 120, .hw_value = 6, },
        { .bitrate = 180, .hw_value = 7, },
        { .bitrate = 240, .hw_value = 8, },
        { .bitrate = 360, .hw_value = 9, },
        { .bitrate = 480, .hw_value = 10, },
        { .bitrate = 540, .hw_value = 11, },
};

static const struct ieee80211_channel rtl818x_channels[] = {
        { .center_freq = 2412 },
        { .center_freq = 2417 },
        { .center_freq = 2422 },
        { .center_freq = 2427 },
        { .center_freq = 2432 },
        { .center_freq = 2437 },
        { .center_freq = 2442 },
        { .center_freq = 2447 },
        { .center_freq = 2452 },
        { .center_freq = 2457 },
        { .center_freq = 2462 },
        { .center_freq = 2467 },
        { .center_freq = 2472 },
        { .center_freq = 2484 },
};

static void rtl8187_iowrite_async_cb(struct urb *urb)
{
        kfree(urb->context);
}

static void rtl8187_iowrite_async(struct rtl8187_priv *priv, __le16 addr,
                                  void *data, u16 len)
{
        struct usb_ctrlrequest *dr;
        struct urb *urb;
        struct rtl8187_async_write_data {
                u8 data[4];
                struct usb_ctrlrequest dr;
        } *buf;
        int rc;

        buf = kmalloc_obj(*buf, GFP_ATOMIC);
        if (!buf)
                return;

        urb = usb_alloc_urb(0, GFP_ATOMIC);
        if (!urb) {
                kfree(buf);
                return;
        }

        dr = &buf->dr;

        dr->bRequestType = RTL8187_REQT_WRITE;
        dr->bRequest = RTL8187_REQ_SET_REG;
        dr->wValue = addr;
        dr->wIndex = 0;
        dr->wLength = cpu_to_le16(len);

        memcpy(buf, data, len);

        usb_fill_control_urb(urb, priv->udev, usb_sndctrlpipe(priv->udev, 0),
                             (unsigned char *)dr, buf, len,
                             rtl8187_iowrite_async_cb, buf);
        usb_anchor_urb(urb, &priv->anchored);
        rc = usb_submit_urb(urb, GFP_ATOMIC);
        if (rc < 0) {
                kfree(buf);
                usb_unanchor_urb(urb);
        }
        usb_free_urb(urb);
}

static inline void rtl818x_iowrite32_async(struct rtl8187_priv *priv,
                                           __le32 *addr, u32 val)
{
        __le32 buf = cpu_to_le32(val);

        rtl8187_iowrite_async(priv, cpu_to_le16((unsigned long)addr),
                              &buf, sizeof(buf));
}

void rtl8187_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data)
{
        struct rtl8187_priv *priv = dev->priv;

        data <<= 8;
        data |= addr | 0x80;

        rtl818x_iowrite8(priv, &priv->map->PHY[3], (data >> 24) & 0xFF);
        rtl818x_iowrite8(priv, &priv->map->PHY[2], (data >> 16) & 0xFF);
        rtl818x_iowrite8(priv, &priv->map->PHY[1], (data >> 8) & 0xFF);
        rtl818x_iowrite8(priv, &priv->map->PHY[0], data & 0xFF);
}

static void rtl8187_tx_cb(struct urb *urb)
{
        struct sk_buff *skb = (struct sk_buff *)urb->context;
        struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
        struct ieee80211_hw *hw = info->rate_driver_data[0];
        struct rtl8187_priv *priv = hw->priv;

        skb_pull(skb, priv->is_rtl8187b ? sizeof(struct rtl8187b_tx_hdr) :
                                          sizeof(struct rtl8187_tx_hdr));
        ieee80211_tx_info_clear_status(info);

        if (!(urb->status) && !(info->flags & IEEE80211_TX_CTL_NO_ACK)) {
                if (priv->is_rtl8187b) {
                        skb_queue_tail(&priv->b_tx_status.queue, skb);

                        /* queue is "full", discard last items */
                        while (skb_queue_len(&priv->b_tx_status.queue) > 5) {
                                struct sk_buff *old_skb;

                                dev_dbg(&priv->udev->dev,
                                        "transmit status queue full\n");

                                old_skb = skb_dequeue(&priv->b_tx_status.queue);
                                ieee80211_tx_status_irqsafe(hw, old_skb);
                        }
                        return;
                } else {
                        info->flags |= IEEE80211_TX_STAT_ACK;
                }
        }
        if (priv->is_rtl8187b)
                ieee80211_tx_status_irqsafe(hw, skb);
        else {
                /* Retry information for the RTI8187 is only available by
                 * reading a register in the device. We are in interrupt mode
                 * here, thus queue the skb and finish on a work queue. */
                skb_queue_tail(&priv->b_tx_status.queue, skb);
                ieee80211_queue_delayed_work(hw, &priv->work, 0);
        }
}

static void rtl8187_tx(struct ieee80211_hw *dev,
                       struct ieee80211_tx_control *control,
                       struct sk_buff *skb)
{
        struct rtl8187_priv *priv = dev->priv;
        struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
        struct ieee80211_hdr *tx_hdr =  (struct ieee80211_hdr *)(skb->data);
        unsigned int ep;
        void *buf;
        struct urb *urb;
        __le16 rts_dur = 0;
        u32 flags;
        int rc;

        urb = usb_alloc_urb(0, GFP_ATOMIC);
        if (!urb) {
                kfree_skb(skb);
                return;
        }

        flags = skb->len;
        flags |= RTL818X_TX_DESC_FLAG_NO_ENC;

        flags |= ieee80211_get_tx_rate(dev, info)->hw_value << 24;
        if (ieee80211_has_morefrags(tx_hdr->frame_control))
                flags |= RTL818X_TX_DESC_FLAG_MOREFRAG;

        /* HW will perform RTS-CTS when only RTS flags is set.
         * HW will perform CTS-to-self when both RTS and CTS flags are set.
         * RTS rate and RTS duration will be used also for CTS-to-self.
         */
        if (info->control.rates[0].flags & IEEE80211_TX_RC_USE_RTS_CTS) {
                flags |= RTL818X_TX_DESC_FLAG_RTS;
                flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19;
                rts_dur = ieee80211_rts_duration(dev, priv->vif,
                                                 skb->len, info);
        } else if (info->control.rates[0].flags & IEEE80211_TX_RC_USE_CTS_PROTECT) {
                flags |= RTL818X_TX_DESC_FLAG_RTS | RTL818X_TX_DESC_FLAG_CTS;
                flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19;
                rts_dur = ieee80211_ctstoself_duration(dev, priv->vif,
                                                 skb->len, info);
        }

        if (info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) {
                if (info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT)
                        priv->seqno += 0x10;
                tx_hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG);
                tx_hdr->seq_ctrl |= cpu_to_le16(priv->seqno);
        }

        if (!priv->is_rtl8187b) {
                struct rtl8187_tx_hdr *hdr = skb_push(skb, sizeof(*hdr));
                hdr->flags = cpu_to_le32(flags);
                hdr->len = 0;
                hdr->rts_duration = rts_dur;
                hdr->retry = cpu_to_le32((info->control.rates[0].count - 1) << 8);
                buf = hdr;

                ep = 2;
        } else {
                /* fc needs to be calculated before skb_push() */
                unsigned int epmap[4] = { 6, 7, 5, 4 };
                u16 fc = le16_to_cpu(tx_hdr->frame_control);

                struct rtl8187b_tx_hdr *hdr = skb_push(skb, sizeof(*hdr));
                struct ieee80211_rate *txrate =
                        ieee80211_get_tx_rate(dev, info);
                memset(hdr, 0, sizeof(*hdr));
                hdr->flags = cpu_to_le32(flags);
                hdr->rts_duration = rts_dur;
                hdr->retry = cpu_to_le32((info->control.rates[0].count - 1) << 8);
                hdr->tx_duration =
                        ieee80211_generic_frame_duration(dev, priv->vif,
                                                         info->band,
                                                         skb->len, txrate);
                buf = hdr;

                if ((fc & IEEE80211_FCTL_FTYPE) == IEEE80211_FTYPE_MGMT)
                        ep = 12;
                else
                        ep = epmap[skb_get_queue_mapping(skb)];
        }

        info->rate_driver_data[0] = dev;
        info->rate_driver_data[1] = urb;

        usb_fill_bulk_urb(urb, priv->udev, usb_sndbulkpipe(priv->udev, ep),
                          buf, skb->len, rtl8187_tx_cb, skb);
        urb->transfer_flags |= URB_ZERO_PACKET;
        usb_anchor_urb(urb, &priv->anchored);
        rc = usb_submit_urb(urb, GFP_ATOMIC);
        if (rc < 0) {
                usb_unanchor_urb(urb);
                kfree_skb(skb);
        }
        usb_free_urb(urb);
}

static void rtl8187_rx_cb(struct urb *urb)
{
        struct sk_buff *skb = (struct sk_buff *)urb->context;
        struct rtl8187_rx_info *info = (struct rtl8187_rx_info *)skb->cb;
        struct ieee80211_hw *dev = info->dev;
        struct rtl8187_priv *priv = dev->priv;
        struct ieee80211_rx_status rx_status = { 0 };
        int rate, signal;
        u32 flags;
        unsigned long f;

        spin_lock_irqsave(&priv->rx_queue.lock, f);
        __skb_unlink(skb, &priv->rx_queue);
        spin_unlock_irqrestore(&priv->rx_queue.lock, f);
        skb_put(skb, urb->actual_length);

        if (unlikely(urb->status))
                goto free_skb;

        if (!priv->is_rtl8187b) {
                struct rtl8187_rx_hdr *hdr;

                if (skb->len < sizeof(struct rtl8187_rx_hdr))
                        goto free_skb;

                hdr = (typeof(hdr))(skb_tail_pointer(skb) - sizeof(*hdr));
                flags = le32_to_cpu(hdr->flags);
                /* As with the RTL8187B below, the AGC is used to calculate
                 * signal strength. In this case, the scaling
                 * constants are derived from the output of p54usb.
                 */
                signal = -4 - ((27 * hdr->agc) >> 6);
                rx_status.antenna = (hdr->signal >> 7) & 1;
                rx_status.mactime = le64_to_cpu(hdr->mac_time);
        } else {
                struct rtl8187b_rx_hdr *hdr;

                if (skb->len < sizeof(struct rtl8187b_rx_hdr))
                        goto free_skb;

                hdr = (typeof(hdr))(skb_tail_pointer(skb) - sizeof(*hdr));
                /* The Realtek datasheet for the RTL8187B shows that the RX
                 * header contains the following quantities: signal quality,
                 * RSSI, AGC, the received power in dB, and the measured SNR.
                 * In testing, none of these quantities show qualitative
                 * agreement with AP signal strength, except for the AGC,
                 * which is inversely proportional to the strength of the
                 * signal. In the following, the signal strength
                 * is derived from the AGC. The arbitrary scaling constants
                 * are chosen to make the results close to the values obtained
                 * for a BCM4312 using b43 as the driver. The noise is ignored
                 * for now.
                 */
                flags = le32_to_cpu(hdr->flags);
                signal = 14 - hdr->agc / 2;
                rx_status.antenna = (hdr->rssi >> 7) & 1;
                rx_status.mactime = le64_to_cpu(hdr->mac_time);
        }

        rx_status.signal = signal;
        priv->signal = signal;
        rate = (flags >> 20) & 0xF;
        skb_trim(skb, flags & 0x0FFF);
        rx_status.rate_idx = rate;
        rx_status.freq = dev->conf.chandef.chan->center_freq;
        rx_status.band = dev->conf.chandef.chan->band;
        rx_status.flag |= RX_FLAG_MACTIME_START;
        if (flags & RTL818X_RX_DESC_FLAG_SPLCP)
                rx_status.enc_flags |= RX_ENC_FLAG_SHORTPRE;
        if (flags & RTL818X_RX_DESC_FLAG_CRC32_ERR)
                rx_status.flag |= RX_FLAG_FAILED_FCS_CRC;
        memcpy(IEEE80211_SKB_RXCB(skb), &rx_status, sizeof(rx_status));
        ieee80211_rx_irqsafe(dev, skb);

        skb = dev_alloc_skb(RTL8187_MAX_RX);
        if (unlikely(!skb)) {
                /* TODO check rx queue length and refill *somewhere* */
                return;
        }

        info = (struct rtl8187_rx_info *)skb->cb;
        info->urb = urb;
        info->dev = dev;
        urb->transfer_buffer = skb_tail_pointer(skb);
        urb->context = skb;
        skb_queue_tail(&priv->rx_queue, skb);

        usb_anchor_urb(urb, &priv->anchored);
        if (usb_submit_urb(urb, GFP_ATOMIC)) {
                usb_unanchor_urb(urb);
                skb_unlink(skb, &priv->rx_queue);
                dev_kfree_skb_irq(skb);
        }
        return;

free_skb:
        dev_kfree_skb_irq(skb);
        return;
}

static int rtl8187_init_urbs(struct ieee80211_hw *dev)
{
        struct rtl8187_priv *priv = dev->priv;
        struct urb *entry = NULL;
        struct sk_buff *skb;
        struct rtl8187_rx_info *info;
        int ret = 0;

        while (skb_queue_len(&priv->rx_queue) < 32) {
                skb = __dev_alloc_skb(RTL8187_MAX_RX, GFP_KERNEL);
                if (!skb) {
                        ret = -ENOMEM;
                        goto err;
                }
                entry = usb_alloc_urb(0, GFP_KERNEL);
                if (!entry) {
                        ret = -ENOMEM;
                        goto err;
                }
                usb_fill_bulk_urb(entry, priv->udev,
                                  usb_rcvbulkpipe(priv->udev,
                                  priv->is_rtl8187b ? 3 : 1),
                                  skb_tail_pointer(skb),
                                  RTL8187_MAX_RX, rtl8187_rx_cb, skb);
                info = (struct rtl8187_rx_info *)skb->cb;
                info->urb = entry;
                info->dev = dev;
                skb_queue_tail(&priv->rx_queue, skb);
                usb_anchor_urb(entry, &priv->anchored);
                ret = usb_submit_urb(entry, GFP_KERNEL);
                if (ret) {
                        skb_unlink(skb, &priv->rx_queue);
                        usb_unanchor_urb(entry);
                        usb_put_urb(entry);
                        goto err;
                }
                usb_put_urb(entry);
        }
        return ret;

err:
        kfree_skb(skb);
        usb_kill_anchored_urbs(&priv->anchored);
        return ret;
}

static void rtl8187b_status_cb(struct urb *urb)
{
        struct ieee80211_hw *hw = (struct ieee80211_hw *)urb->context;
        struct rtl8187_priv *priv = hw->priv;
        u64 val;
        unsigned int cmd_type;

        if (unlikely(urb->status))
                return;

        /*
         * Read from status buffer:
         *
         * bits [30:31] = cmd type:
         * - 0 indicates tx beacon interrupt
         * - 1 indicates tx close descriptor
         *
         * In the case of tx beacon interrupt:
         * [0:9] = Last Beacon CW
         * [10:29] = reserved
         * [30:31] = 00b
         * [32:63] = Last Beacon TSF
         *
         * If it's tx close descriptor:
         * [0:7] = Packet Retry Count
         * [8:14] = RTS Retry Count
         * [15] = TOK
         * [16:27] = Sequence No
         * [28] = LS
         * [29] = FS
         * [30:31] = 01b
         * [32:47] = unused (reserved?)
         * [48:63] = MAC Used Time
         */
        val = le64_to_cpu(priv->b_tx_status.buf);

        cmd_type = (val >> 30) & 0x3;
        if (cmd_type == 1) {
                unsigned int pkt_rc, seq_no;
                bool tok;
                struct sk_buff *skb, *iter;
                struct ieee80211_hdr *ieee80211hdr;
                unsigned long flags;

                pkt_rc = val & 0xFF;
                tok = val & (1 << 15);
                seq_no = (val >> 16) & 0xFFF;

                spin_lock_irqsave(&priv->b_tx_status.queue.lock, flags);
                skb = NULL;
                skb_queue_reverse_walk(&priv->b_tx_status.queue, iter) {
                        ieee80211hdr = (struct ieee80211_hdr *)iter->data;

                        /*
                         * While testing, it was discovered that the seq_no
                         * doesn't actually contains the sequence number.
                         * Instead of returning just the 12 bits of sequence
                         * number, hardware is returning entire sequence control
                         * (fragment number plus sequence number) in a 12 bit
                         * only field overflowing after some time. As a
                         * workaround, just consider the lower bits, and expect
                         * it's unlikely we wrongly ack some sent data
                         */
                        if ((le16_to_cpu(ieee80211hdr->seq_ctrl)
                             & 0xFFF) == seq_no) {
                                skb = iter;
                                break;
                        }
                }
                if (skb) {
                        struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);

                        __skb_unlink(skb, &priv->b_tx_status.queue);
                        if (tok)
                                info->flags |= IEEE80211_TX_STAT_ACK;
                        info->status.rates[0].count = pkt_rc + 1;

                        ieee80211_tx_status_irqsafe(hw, skb);
                }
                spin_unlock_irqrestore(&priv->b_tx_status.queue.lock, flags);
        }

        usb_anchor_urb(urb, &priv->anchored);
        if (usb_submit_urb(urb, GFP_ATOMIC))
                usb_unanchor_urb(urb);
}

static int rtl8187b_init_status_urb(struct ieee80211_hw *dev)
{
        struct rtl8187_priv *priv = dev->priv;
        struct urb *entry;
        int ret = 0;

        entry = usb_alloc_urb(0, GFP_KERNEL);
        if (!entry)
                return -ENOMEM;

        usb_fill_bulk_urb(entry, priv->udev, usb_rcvbulkpipe(priv->udev, 9),
                          &priv->b_tx_status.buf, sizeof(priv->b_tx_status.buf),
                          rtl8187b_status_cb, dev);

        usb_anchor_urb(entry, &priv->anchored);
        ret = usb_submit_urb(entry, GFP_KERNEL);
        if (ret)
                usb_unanchor_urb(entry);
        usb_free_urb(entry);

        return ret;
}

static void rtl8187_set_anaparam(struct rtl8187_priv *priv, bool rfon)
{
        u32 anaparam, anaparam2;
        u8 anaparam3, reg;

        if (!priv->is_rtl8187b) {
                if (rfon) {
                        anaparam = RTL8187_RTL8225_ANAPARAM_ON;
                        anaparam2 = RTL8187_RTL8225_ANAPARAM2_ON;
                } else {
                        anaparam = RTL8187_RTL8225_ANAPARAM_OFF;
                        anaparam2 = RTL8187_RTL8225_ANAPARAM2_OFF;
                }
        } else {
                if (rfon) {
                        anaparam = RTL8187B_RTL8225_ANAPARAM_ON;
                        anaparam2 = RTL8187B_RTL8225_ANAPARAM2_ON;
                        anaparam3 = RTL8187B_RTL8225_ANAPARAM3_ON;
                } else {
                        anaparam = RTL8187B_RTL8225_ANAPARAM_OFF;
                        anaparam2 = RTL8187B_RTL8225_ANAPARAM2_OFF;
                        anaparam3 = RTL8187B_RTL8225_ANAPARAM3_OFF;
                }
        }

        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
                         RTL818X_EEPROM_CMD_CONFIG);
        reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
        reg |= RTL818X_CONFIG3_ANAPARAM_WRITE;
        rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg);
        rtl818x_iowrite32(priv, &priv->map->ANAPARAM, anaparam);
        rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, anaparam2);
        if (priv->is_rtl8187b)
                rtl818x_iowrite8(priv, &priv->map->ANAPARAM3A, anaparam3);
        reg &= ~RTL818X_CONFIG3_ANAPARAM_WRITE;
        rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg);
        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
                         RTL818X_EEPROM_CMD_NORMAL);
}

static int rtl8187_cmd_reset(struct ieee80211_hw *dev)
{
        struct rtl8187_priv *priv = dev->priv;
        u8 reg;
        int i;

        reg = rtl818x_ioread8(priv, &priv->map->CMD);
        reg &= (1 << 1);
        reg |= RTL818X_CMD_RESET;
        rtl818x_iowrite8(priv, &priv->map->CMD, reg);

        i = 10;
        do {
                msleep(2);
                if (!(rtl818x_ioread8(priv, &priv->map->CMD) &
                      RTL818X_CMD_RESET))
                        break;
        } while (--i);

        if (!i) {
                wiphy_err(dev->wiphy, "Reset timeout!\n");
                return -ETIMEDOUT;
        }

        /* reload registers from eeprom */
        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_LOAD);

        i = 10;
        do {
                msleep(4);
                if (!(rtl818x_ioread8(priv, &priv->map->EEPROM_CMD) &
                      RTL818X_EEPROM_CMD_CONFIG))
                        break;
        } while (--i);

        if (!i) {
                wiphy_err(dev->wiphy, "eeprom reset timeout!\n");
                return -ETIMEDOUT;
        }

        return 0;
}

static int rtl8187_init_hw(struct ieee80211_hw *dev)
{
        struct rtl8187_priv *priv = dev->priv;
        u8 reg;
        int res;

        /* reset */
        rtl8187_set_anaparam(priv, true);

        rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0);

        msleep(200);
        rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x10);
        rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x11);
        rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x00);
        msleep(200);

        res = rtl8187_cmd_reset(dev);
        if (res)
                return res;

        rtl8187_set_anaparam(priv, true);

        /* setup card */
        rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0);
        rtl818x_iowrite8(priv, &priv->map->GPIO0, 0);

        rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8));
        rtl818x_iowrite8(priv, &priv->map->GPIO0, 1);
        rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0);

        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);

        rtl818x_iowrite16(priv, (__le16 *)0xFFF4, 0xFFFF);
        reg = rtl818x_ioread8(priv, &priv->map->CONFIG1);
        reg &= 0x3F;
        reg |= 0x80;
        rtl818x_iowrite8(priv, &priv->map->CONFIG1, reg);

        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);

        rtl818x_iowrite32(priv, &priv->map->INT_TIMEOUT, 0);
        rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0);
        rtl818x_iowrite8(priv, &priv->map->RATE_FALLBACK, 0);

        // TODO: set RESP_RATE and BRSR properly
        rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (8 << 4) | 0);
        rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);

        /* host_usb_init */
        rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0);
        rtl818x_iowrite8(priv, &priv->map->GPIO0, 0);
        reg = rtl818x_ioread8(priv, (u8 *)0xFE53);
        rtl818x_iowrite8(priv, (u8 *)0xFE53, reg | (1 << 7));
        rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8));
        rtl818x_iowrite8(priv, &priv->map->GPIO0, 0x20);
        rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0);
        rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x80);
        rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x80);
        rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x80);
        msleep(100);

        rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x000a8008);
        rtl818x_iowrite16(priv, &priv->map->BRSR, 0xFFFF);
        rtl818x_iowrite32(priv, &priv->map->RF_PARA, 0x00100044);
        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
                         RTL818X_EEPROM_CMD_CONFIG);
        rtl818x_iowrite8(priv, &priv->map->CONFIG3, 0x44);
        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
                         RTL818X_EEPROM_CMD_NORMAL);
        rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FF7);
        msleep(100);

        priv->rf->init(dev);

        rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
        reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~1;
        rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1);
        rtl818x_iowrite16(priv, (__le16 *)0xFFFE, 0x10);
        rtl818x_iowrite8(priv, &priv->map->TALLY_SEL, 0x80);
        rtl818x_iowrite8(priv, (u8 *)0xFFFF, 0x60);
        rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg);

        return 0;
}

static const u8 rtl8187b_reg_table[][3] = {
        {0xF0, 0x32, 0}, {0xF1, 0x32, 0}, {0xF2, 0x00, 0}, {0xF3, 0x00, 0},
        {0xF4, 0x32, 0}, {0xF5, 0x43, 0}, {0xF6, 0x00, 0}, {0xF7, 0x00, 0},
        {0xF8, 0x46, 0}, {0xF9, 0xA4, 0}, {0xFA, 0x00, 0}, {0xFB, 0x00, 0},
        {0xFC, 0x96, 0}, {0xFD, 0xA4, 0}, {0xFE, 0x00, 0}, {0xFF, 0x00, 0},

        {0x58, 0x4B, 1}, {0x59, 0x00, 1}, {0x5A, 0x4B, 1}, {0x5B, 0x00, 1},
        {0x60, 0x4B, 1}, {0x61, 0x09, 1}, {0x62, 0x4B, 1}, {0x63, 0x09, 1},
        {0xCE, 0x0F, 1}, {0xCF, 0x00, 1}, {0xF0, 0x4E, 1}, {0xF1, 0x01, 1},
        {0xF2, 0x02, 1}, {0xF3, 0x03, 1}, {0xF4, 0x04, 1}, {0xF5, 0x05, 1},
        {0xF6, 0x06, 1}, {0xF7, 0x07, 1}, {0xF8, 0x08, 1},

        {0x4E, 0x00, 2}, {0x0C, 0x04, 2}, {0x21, 0x61, 2}, {0x22, 0x68, 2},
        {0x23, 0x6F, 2}, {0x24, 0x76, 2}, {0x25, 0x7D, 2}, {0x26, 0x84, 2},
        {0x27, 0x8D, 2}, {0x4D, 0x08, 2}, {0x50, 0x05, 2}, {0x51, 0xF5, 2},
        {0x52, 0x04, 2}, {0x53, 0xA0, 2}, {0x54, 0x1F, 2}, {0x55, 0x23, 2},
        {0x56, 0x45, 2}, {0x57, 0x67, 2}, {0x58, 0x08, 2}, {0x59, 0x08, 2},
        {0x5A, 0x08, 2}, {0x5B, 0x08, 2}, {0x60, 0x08, 2}, {0x61, 0x08, 2},
        {0x62, 0x08, 2}, {0x63, 0x08, 2}, {0x64, 0xCF, 2},

        {0x5B, 0x40, 0}, {0x84, 0x88, 0}, {0x85, 0x24, 0}, {0x88, 0x54, 0},
        {0x8B, 0xB8, 0}, {0x8C, 0x07, 0}, {0x8D, 0x00, 0}, {0x94, 0x1B, 0},
        {0x95, 0x12, 0}, {0x96, 0x00, 0}, {0x97, 0x06, 0}, {0x9D, 0x1A, 0},
        {0x9F, 0x10, 0}, {0xB4, 0x22, 0}, {0xBE, 0x80, 0}, {0xDB, 0x00, 0},
        {0xEE, 0x00, 0}, {0x4C, 0x00, 2},

        {0x9F, 0x00, 3}, {0x8C, 0x01, 0}, {0x8D, 0x10, 0}, {0x8E, 0x08, 0},
        {0x8F, 0x00, 0}
};

static int rtl8187b_init_hw(struct ieee80211_hw *dev)
{
        struct rtl8187_priv *priv = dev->priv;
        int res, i;
        u8 reg;

        rtl8187_set_anaparam(priv, true);

        /* Reset PLL sequence on 8187B. Realtek note: reduces power
         * consumption about 30 mA */
        rtl818x_iowrite8(priv, (u8 *)0xFF61, 0x10);
        reg = rtl818x_ioread8(priv, (u8 *)0xFF62);
        rtl818x_iowrite8(priv, (u8 *)0xFF62, reg & ~(1 << 5));
        rtl818x_iowrite8(priv, (u8 *)0xFF62, reg | (1 << 5));

        res = rtl8187_cmd_reset(dev);
        if (res)
                return res;

        rtl8187_set_anaparam(priv, true);

        /* BRSR (Basic Rate Set Register) on 8187B looks to be the same as
         * RESP_RATE on 8187L in Realtek sources: each bit should be each
         * one of the 12 rates, all are enabled */
        rtl818x_iowrite16(priv, (__le16 *)0xFF34, 0x0FFF);

        reg = rtl818x_ioread8(priv, &priv->map->CW_CONF);
        reg |= RTL818X_CW_CONF_PERPACKET_RETRY;
        rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg);

        /* Auto Rate Fallback Register (ARFR): 1M-54M setting */
        rtl818x_iowrite16_idx(priv, (__le16 *)0xFFE0, 0x0FFF, 1);
        rtl818x_iowrite8_idx(priv, (u8 *)0xFFE2, 0x00, 1);

        rtl818x_iowrite16_idx(priv, (__le16 *)0xFFD4, 0xFFFF, 1);

        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
                         RTL818X_EEPROM_CMD_CONFIG);
        reg = rtl818x_ioread8(priv, &priv->map->CONFIG1);
        rtl818x_iowrite8(priv, &priv->map->CONFIG1, (reg & 0x3F) | 0x80);
        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
                         RTL818X_EEPROM_CMD_NORMAL);

        rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0);
        for (i = 0; i < ARRAY_SIZE(rtl8187b_reg_table); i++) {
                rtl818x_iowrite8_idx(priv,
                                     (u8 *)(uintptr_t)
                                     (rtl8187b_reg_table[i][0] | 0xFF00),
                                     rtl8187b_reg_table[i][1],
                                     rtl8187b_reg_table[i][2]);
        }

        rtl818x_iowrite16(priv, &priv->map->TID_AC_MAP, 0xFA50);
        rtl818x_iowrite16(priv, &priv->map->INT_MIG, 0);

        rtl818x_iowrite32_idx(priv, (__le32 *)0xFFF0, 0, 1);
        rtl818x_iowrite32_idx(priv, (__le32 *)0xFFF4, 0, 1);
        rtl818x_iowrite8_idx(priv, (u8 *)0xFFF8, 0, 1);

        rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x00004001);

        /* RFSW_CTRL register */
        rtl818x_iowrite16_idx(priv, (__le16 *)0xFF72, 0x569A, 2);

        rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x0480);
        rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x2488);
        rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FFF);
        msleep(100);

        priv->rf->init(dev);

        reg = RTL818X_CMD_TX_ENABLE | RTL818X_CMD_RX_ENABLE;
        rtl818x_iowrite8(priv, &priv->map->CMD, reg);
        rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF);

        rtl818x_iowrite8(priv, (u8 *)0xFE41, 0xF4);
        rtl818x_iowrite8(priv, (u8 *)0xFE40, 0x00);
        rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x00);
        rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x01);
        rtl818x_iowrite8(priv, (u8 *)0xFE40, 0x0F);
        rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x00);
        rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x01);

        reg = rtl818x_ioread8(priv, (u8 *)0xFFDB);
        rtl818x_iowrite8(priv, (u8 *)0xFFDB, reg | (1 << 2));
        rtl818x_iowrite16_idx(priv, (__le16 *)0xFF72, 0x59FA, 3);
        rtl818x_iowrite16_idx(priv, (__le16 *)0xFF74, 0x59D2, 3);
        rtl818x_iowrite16_idx(priv, (__le16 *)0xFF76, 0x59D2, 3);
        rtl818x_iowrite16_idx(priv, (__le16 *)0xFF78, 0x19FA, 3);
        rtl818x_iowrite16_idx(priv, (__le16 *)0xFF7A, 0x19FA, 3);
        rtl818x_iowrite16_idx(priv, (__le16 *)0xFF7C, 0x00D0, 3);
        rtl818x_iowrite8(priv, (u8 *)0xFF61, 0);
        rtl818x_iowrite8_idx(priv, (u8 *)0xFF80, 0x0F, 1);
        rtl818x_iowrite8_idx(priv, (u8 *)0xFF83, 0x03, 1);
        rtl818x_iowrite8(priv, (u8 *)0xFFDA, 0x10);
        rtl818x_iowrite8_idx(priv, (u8 *)0xFF4D, 0x08, 2);

        rtl818x_iowrite32(priv, &priv->map->HSSI_PARA, 0x0600321B);

        rtl818x_iowrite16_idx(priv, (__le16 *)0xFFEC, 0x0800, 1);

        priv->slot_time = 0x9;
        priv->aifsn[0] = 2; /* AIFSN[AC_VO] */
        priv->aifsn[1] = 2; /* AIFSN[AC_VI] */
        priv->aifsn[2] = 7; /* AIFSN[AC_BK] */
        priv->aifsn[3] = 3; /* AIFSN[AC_BE] */
        rtl818x_iowrite8(priv, &priv->map->ACM_CONTROL, 0);

        /* ENEDCA flag must always be set, transmit issues? */
        rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_ENEDCA);

        return 0;
}

static void rtl8187_work(struct work_struct *work)
{
        /* The RTL8187 returns the retry count through register 0xFFFA. In
         * addition, it appears to be a cumulative retry count, not the
         * value for the current TX packet. When multiple TX entries are
         * waiting in the queue, the retry count will be the total for all.
         * The "error" may matter for purposes of rate setting, but there is
         * no other choice with this hardware.
         */
        struct rtl8187_priv *priv = container_of(work, struct rtl8187_priv,
                                    work.work);
        struct ieee80211_tx_info *info;
        struct ieee80211_hw *dev = priv->dev;
        static u16 retry;
        u16 tmp;
        u16 avg_retry;
        int length;

        mutex_lock(&priv->conf_mutex);
        tmp = rtl818x_ioread16(priv, (__le16 *)0xFFFA);
        length = skb_queue_len(&priv->b_tx_status.queue);
        if (unlikely(!length))
                length = 1;
        if (unlikely(tmp < retry))
                tmp = retry;
        avg_retry = (tmp - retry) / length;
        while (skb_queue_len(&priv->b_tx_status.queue) > 0) {
                struct sk_buff *old_skb;

                old_skb = skb_dequeue(&priv->b_tx_status.queue);
                info = IEEE80211_SKB_CB(old_skb);
                info->status.rates[0].count = avg_retry + 1;
                if (info->status.rates[0].count > RETRY_COUNT)
                        info->flags &= ~IEEE80211_TX_STAT_ACK;
                ieee80211_tx_status_irqsafe(dev, old_skb);
        }
        retry = tmp;
        mutex_unlock(&priv->conf_mutex);
}

static int rtl8187_start(struct ieee80211_hw *dev)
{
        struct rtl8187_priv *priv = dev->priv;
        u32 reg;
        int ret;

        mutex_lock(&priv->conf_mutex);

        ret = (!priv->is_rtl8187b) ? rtl8187_init_hw(dev) :
                                     rtl8187b_init_hw(dev);
        if (ret)
                goto rtl8187_start_exit;

        init_usb_anchor(&priv->anchored);
        priv->dev = dev;

        if (priv->is_rtl8187b) {
                reg = RTL818X_RX_CONF_MGMT |
                      RTL818X_RX_CONF_DATA |
                      RTL818X_RX_CONF_BROADCAST |
                      RTL818X_RX_CONF_NICMAC |
                      RTL818X_RX_CONF_BSSID |
                      (7 << 13 /* RX FIFO threshold NONE */) |
                      (7 << 10 /* MAX RX DMA */) |
                      RTL818X_RX_CONF_RX_AUTORESETPHY |
                      RTL818X_RX_CONF_ONLYERLPKT;
                priv->rx_conf = reg;
                rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg);

                reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL);
                reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN;
                reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL;
                reg &= ~RTL818X_TX_AGC_CTL_FEEDBACK_ANT;
                rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg);

                rtl818x_iowrite32(priv, &priv->map->TX_CONF,
                                  RTL818X_TX_CONF_HW_SEQNUM |
                                  RTL818X_TX_CONF_DISREQQSIZE |
                                  (RETRY_COUNT << 8  /* short retry limit */) |
                                  (RETRY_COUNT << 0  /* long retry limit */) |
                                  (7 << 21 /* MAX TX DMA */));
                ret = rtl8187_init_urbs(dev);
                if (ret)
                        goto rtl8187_start_exit;
                ret = rtl8187b_init_status_urb(dev);
                if (ret)
                        usb_kill_anchored_urbs(&priv->anchored);
                goto rtl8187_start_exit;
        }

        rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF);

        rtl818x_iowrite32(priv, &priv->map->MAR[0], ~0);
        rtl818x_iowrite32(priv, &priv->map->MAR[1], ~0);

        ret = rtl8187_init_urbs(dev);
        if (ret)
                goto rtl8187_start_exit;

        reg = RTL818X_RX_CONF_ONLYERLPKT |
              RTL818X_RX_CONF_RX_AUTORESETPHY |
              RTL818X_RX_CONF_BSSID |
              RTL818X_RX_CONF_MGMT |
              RTL818X_RX_CONF_DATA |
              (7 << 13 /* RX FIFO threshold NONE */) |
              (7 << 10 /* MAX RX DMA */) |
              RTL818X_RX_CONF_BROADCAST |
              RTL818X_RX_CONF_NICMAC;

        priv->rx_conf = reg;
        rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg);

        reg = rtl818x_ioread8(priv, &priv->map->CW_CONF);
        reg &= ~RTL818X_CW_CONF_PERPACKET_CW;
        reg |= RTL818X_CW_CONF_PERPACKET_RETRY;
        rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg);

        reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL);
        reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN;
        reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL;
        reg &= ~RTL818X_TX_AGC_CTL_FEEDBACK_ANT;
        rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg);

        reg  = RTL818X_TX_CONF_CW_MIN |
               (7 << 21 /* MAX TX DMA */) |
               RTL818X_TX_CONF_NO_ICV;
        rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg);

        reg = rtl818x_ioread8(priv, &priv->map->CMD);
        reg |= RTL818X_CMD_TX_ENABLE;
        reg |= RTL818X_CMD_RX_ENABLE;
        rtl818x_iowrite8(priv, &priv->map->CMD, reg);
        INIT_DELAYED_WORK(&priv->work, rtl8187_work);

rtl8187_start_exit:
        mutex_unlock(&priv->conf_mutex);
        return ret;
}

static void rtl8187_stop(struct ieee80211_hw *dev, bool suspend)
{
        struct rtl8187_priv *priv = dev->priv;
        struct sk_buff *skb;
        u32 reg;

        mutex_lock(&priv->conf_mutex);
        rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0);

        reg = rtl818x_ioread8(priv, &priv->map->CMD);
        reg &= ~RTL818X_CMD_TX_ENABLE;
        reg &= ~RTL818X_CMD_RX_ENABLE;
        rtl818x_iowrite8(priv, &priv->map->CMD, reg);

        priv->rf->stop(dev);
        rtl8187_set_anaparam(priv, false);

        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
        reg = rtl818x_ioread8(priv, &priv->map->CONFIG4);
        rtl818x_iowrite8(priv, &priv->map->CONFIG4, reg | RTL818X_CONFIG4_VCOOFF);
        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);

        usb_kill_anchored_urbs(&priv->anchored);

        while ((skb = skb_dequeue(&priv->b_tx_status.queue)))
                dev_kfree_skb_any(skb);

        mutex_unlock(&priv->conf_mutex);

        if (!priv->is_rtl8187b)
                cancel_delayed_work_sync(&priv->work);
}

static u64 rtl8187_get_tsf(struct ieee80211_hw *dev, struct ieee80211_vif *vif)
{
        struct rtl8187_priv *priv = dev->priv;

        return rtl818x_ioread32(priv, &priv->map->TSFT[0]) |
               (u64)(rtl818x_ioread32(priv, &priv->map->TSFT[1])) << 32;
}


static void rtl8187_beacon_work(struct work_struct *work)
{
        struct rtl8187_vif *vif_priv =
                container_of(work, struct rtl8187_vif, beacon_work.work);
        struct ieee80211_vif *vif =
                container_of((void *)vif_priv, struct ieee80211_vif, drv_priv);
        struct ieee80211_hw *dev = vif_priv->dev;
        struct ieee80211_mgmt *mgmt;
        struct sk_buff *skb;

        /* don't overflow the tx ring */
        if (ieee80211_queue_stopped(dev, 0))
                goto resched;

        /* grab a fresh beacon */
        skb = ieee80211_beacon_get(dev, vif, 0);
        if (!skb)
                goto resched;

        /*
         * update beacon timestamp w/ TSF value
         * TODO: make hardware update beacon timestamp
         */
        mgmt = (struct ieee80211_mgmt *)skb->data;
        mgmt->u.beacon.timestamp = cpu_to_le64(rtl8187_get_tsf(dev, vif));

        /* TODO: use actual beacon queue */
        skb_set_queue_mapping(skb, 0);

        rtl8187_tx(dev, NULL, skb);

resched:
        /*
         * schedule next beacon
         * TODO: use hardware support for beacon timing
         */
        schedule_delayed_work(&vif_priv->beacon_work,
                        usecs_to_jiffies(1024 * vif->bss_conf.beacon_int));
}


static int rtl8187_add_interface(struct ieee80211_hw *dev,
                                 struct ieee80211_vif *vif)
{
        struct rtl8187_priv *priv = dev->priv;
        struct rtl8187_vif *vif_priv;
        int i;
        int ret = -EOPNOTSUPP;

        mutex_lock(&priv->conf_mutex);
        if (priv->vif)
                goto exit;

        switch (vif->type) {
        case NL80211_IFTYPE_STATION:
        case NL80211_IFTYPE_ADHOC:
                break;
        default:
                goto exit;
        }

        ret = 0;
        priv->vif = vif;

        /* Initialize driver private area */
        vif_priv = (struct rtl8187_vif *)&vif->drv_priv;
        vif_priv->dev = dev;
        INIT_DELAYED_WORK(&vif_priv->beacon_work, rtl8187_beacon_work);
        vif_priv->enable_beacon = false;


        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
        for (i = 0; i < ETH_ALEN; i++)
                rtl818x_iowrite8(priv, &priv->map->MAC[i],
                                 ((u8 *)vif->addr)[i]);
        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);

exit:
        mutex_unlock(&priv->conf_mutex);
        return ret;
}

static void rtl8187_remove_interface(struct ieee80211_hw *dev,
                                     struct ieee80211_vif *vif)
{
        struct rtl8187_priv *priv = dev->priv;
        mutex_lock(&priv->conf_mutex);
        priv->vif = NULL;
        mutex_unlock(&priv->conf_mutex);
}

static int rtl8187_config(struct ieee80211_hw *dev, int radio_idx, u32 changed)
{
        struct rtl8187_priv *priv = dev->priv;
        struct ieee80211_conf *conf = &dev->conf;
        u32 reg;

        mutex_lock(&priv->conf_mutex);
        reg = rtl818x_ioread32(priv, &priv->map->TX_CONF);
        /* Enable TX loopback on MAC level to avoid TX during channel
         * changes, as this has be seen to causes problems and the
         * card will stop work until next reset
         */
        rtl818x_iowrite32(priv, &priv->map->TX_CONF,
                          reg | RTL818X_TX_CONF_LOOPBACK_MAC);
        priv->rf->set_chan(dev, conf);
        msleep(10);
        rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg);

        rtl818x_iowrite16(priv, &priv->map->ATIM_WND, 2);
        rtl818x_iowrite16(priv, &priv->map->ATIMTR_INTERVAL, 100);
        rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL, 100);
        rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL_TIME, 100);
        mutex_unlock(&priv->conf_mutex);
        return 0;
}

/*
 * With 8187B, AC_*_PARAM clashes with FEMR definition in struct rtl818x_csr for
 * example. Thus we have to use raw values for AC_*_PARAM register addresses.
 */
static __le32 *rtl8187b_ac_addr[4] = {
        (__le32 *) 0xFFF0, /* AC_VO */
        (__le32 *) 0xFFF4, /* AC_VI */
        (__le32 *) 0xFFFC, /* AC_BK */
        (__le32 *) 0xFFF8, /* AC_BE */
};

#define SIFS_TIME 0xa

static void rtl8187_conf_erp(struct rtl8187_priv *priv, bool use_short_slot,
                             bool use_short_preamble)
{
        if (priv->is_rtl8187b) {
                u8 difs, eifs;
                u16 ack_timeout;
                int queue;

                if (use_short_slot) {
                        priv->slot_time = 0x9;
                        difs = 0x1c;
                        eifs = 0x53;
                } else {
                        priv->slot_time = 0x14;
                        difs = 0x32;
                        eifs = 0x5b;
                }
                rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22);
                rtl818x_iowrite8(priv, &priv->map->SLOT, priv->slot_time);
                rtl818x_iowrite8(priv, &priv->map->DIFS, difs);

                /*
                 * BRSR+1 on 8187B is in fact EIFS register
                 * Value in units of 4 us
                 */
                rtl818x_iowrite8(priv, (u8 *)&priv->map->BRSR + 1, eifs);

                /*
                 * For 8187B, CARRIER_SENSE_COUNTER is in fact ack timeout
                 * register. In units of 4 us like eifs register
                 * ack_timeout = ack duration + plcp + difs + preamble
                 */
                ack_timeout = 112 + 48 + difs;
                if (use_short_preamble)
                        ack_timeout += 72;
                else
                        ack_timeout += 144;
                rtl818x_iowrite8(priv, &priv->map->CARRIER_SENSE_COUNTER,
                                 DIV_ROUND_UP(ack_timeout, 4));

                for (queue = 0; queue < 4; queue++)
                        rtl818x_iowrite8(priv, (u8 *) rtl8187b_ac_addr[queue],
                                         priv->aifsn[queue] * priv->slot_time +
                                         SIFS_TIME);
        } else {
                rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22);
                if (use_short_slot) {
                        rtl818x_iowrite8(priv, &priv->map->SLOT, 0x9);
                        rtl818x_iowrite8(priv, &priv->map->DIFS, 0x14);
                        rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x14);
                } else {
                        rtl818x_iowrite8(priv, &priv->map->SLOT, 0x14);
                        rtl818x_iowrite8(priv, &priv->map->DIFS, 0x24);
                        rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x24);
                }
        }
}

static void rtl8187_bss_info_changed(struct ieee80211_hw *dev,
                                     struct ieee80211_vif *vif,
                                     struct ieee80211_bss_conf *info,
                                     u64 changed)
{
        struct rtl8187_priv *priv = dev->priv;
        struct rtl8187_vif *vif_priv;
        int i;
        u8 reg;

        vif_priv = (struct rtl8187_vif *)&vif->drv_priv;

        if (changed & BSS_CHANGED_BSSID) {
                mutex_lock(&priv->conf_mutex);
                for (i = 0; i < ETH_ALEN; i++)
                        rtl818x_iowrite8(priv, &priv->map->BSSID[i],
                                         info->bssid[i]);

                if (priv->is_rtl8187b)
                        reg = RTL818X_MSR_ENEDCA;
                else
                        reg = 0;

                if (is_valid_ether_addr(info->bssid)) {
                        if (vif->type == NL80211_IFTYPE_ADHOC)
                                reg |= RTL818X_MSR_ADHOC;
                        else
                                reg |= RTL818X_MSR_INFRA;
                }
                else
                        reg |= RTL818X_MSR_NO_LINK;

                rtl818x_iowrite8(priv, &priv->map->MSR, reg);

                mutex_unlock(&priv->conf_mutex);
        }

        if (changed & (BSS_CHANGED_ERP_SLOT | BSS_CHANGED_ERP_PREAMBLE))
                rtl8187_conf_erp(priv, info->use_short_slot,
                                 info->use_short_preamble);

        if (changed & BSS_CHANGED_BEACON_ENABLED)
                vif_priv->enable_beacon = info->enable_beacon;

        if (changed & (BSS_CHANGED_BEACON_ENABLED | BSS_CHANGED_BEACON)) {
                cancel_delayed_work_sync(&vif_priv->beacon_work);
                if (vif_priv->enable_beacon)
                        schedule_work(&vif_priv->beacon_work.work);
        }

}

static u64 rtl8187_prepare_multicast(struct ieee80211_hw *dev,
                                     struct netdev_hw_addr_list *mc_list)
{
        return netdev_hw_addr_list_count(mc_list);
}

static void rtl8187_configure_filter(struct ieee80211_hw *dev,
                                     unsigned int changed_flags,
                                     unsigned int *total_flags,
                                     u64 multicast)
{
        struct rtl8187_priv *priv = dev->priv;

        if (changed_flags & FIF_FCSFAIL)
                priv->rx_conf ^= RTL818X_RX_CONF_FCS;
        if (changed_flags & FIF_CONTROL)
                priv->rx_conf ^= RTL818X_RX_CONF_CTRL;
        if (*total_flags & FIF_OTHER_BSS ||
            *total_flags & FIF_ALLMULTI || multicast > 0)
                priv->rx_conf |= RTL818X_RX_CONF_MONITOR;
        else
                priv->rx_conf &= ~RTL818X_RX_CONF_MONITOR;

        *total_flags = 0;

        if (priv->rx_conf & RTL818X_RX_CONF_FCS)
                *total_flags |= FIF_FCSFAIL;
        if (priv->rx_conf & RTL818X_RX_CONF_CTRL)
                *total_flags |= FIF_CONTROL;
        if (priv->rx_conf & RTL818X_RX_CONF_MONITOR) {
                *total_flags |= FIF_OTHER_BSS;
                *total_flags |= FIF_ALLMULTI;
        }

        rtl818x_iowrite32_async(priv, &priv->map->RX_CONF, priv->rx_conf);
}

static int rtl8187_conf_tx(struct ieee80211_hw *dev,
                           struct ieee80211_vif *vif,
                           unsigned int link_id, u16 queue,
                           const struct ieee80211_tx_queue_params *params)
{
        struct rtl8187_priv *priv = dev->priv;
        u8 cw_min, cw_max;

        if (queue > 3)
                return -EINVAL;

        cw_min = fls(params->cw_min);
        cw_max = fls(params->cw_max);

        if (priv->is_rtl8187b) {
                priv->aifsn[queue] = params->aifs;

                /*
                 * This is the structure of AC_*_PARAM registers in 8187B:
                 * - TXOP limit field, bit offset = 16
                 * - ECWmax, bit offset = 12
                 * - ECWmin, bit offset = 8
                 * - AIFS, bit offset = 0
                 */
                rtl818x_iowrite32(priv, rtl8187b_ac_addr[queue],
                                  (params->txop << 16) | (cw_max << 12) |
                                  (cw_min << 8) | (params->aifs *
                                  priv->slot_time + SIFS_TIME));
        } else {
                if (queue != 0)
                        return -EINVAL;

                rtl818x_iowrite8(priv, &priv->map->CW_VAL,
                                 cw_min | (cw_max << 4));
        }
        return 0;
}


static const struct ieee80211_ops rtl8187_ops = {
        .add_chanctx = ieee80211_emulate_add_chanctx,
        .remove_chanctx = ieee80211_emulate_remove_chanctx,
        .change_chanctx = ieee80211_emulate_change_chanctx,
        .switch_vif_chanctx = ieee80211_emulate_switch_vif_chanctx,
        .tx                     = rtl8187_tx,
        .wake_tx_queue          = ieee80211_handle_wake_tx_queue,
        .start                  = rtl8187_start,
        .stop                   = rtl8187_stop,
        .add_interface          = rtl8187_add_interface,
        .remove_interface       = rtl8187_remove_interface,
        .config                 = rtl8187_config,
        .bss_info_changed       = rtl8187_bss_info_changed,
        .prepare_multicast      = rtl8187_prepare_multicast,
        .configure_filter       = rtl8187_configure_filter,
        .conf_tx                = rtl8187_conf_tx,
        .rfkill_poll            = rtl8187_rfkill_poll,
        .get_tsf                = rtl8187_get_tsf,
};

static void rtl8187_eeprom_register_read(struct eeprom_93cx6 *eeprom)
{
        struct ieee80211_hw *dev = eeprom->data;
        struct rtl8187_priv *priv = dev->priv;
        u8 reg = rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);

        eeprom->reg_data_in = reg & RTL818X_EEPROM_CMD_WRITE;
        eeprom->reg_data_out = reg & RTL818X_EEPROM_CMD_READ;
        eeprom->reg_data_clock = reg & RTL818X_EEPROM_CMD_CK;
        eeprom->reg_chip_select = reg & RTL818X_EEPROM_CMD_CS;
}

static void rtl8187_eeprom_register_write(struct eeprom_93cx6 *eeprom)
{
        struct ieee80211_hw *dev = eeprom->data;
        struct rtl8187_priv *priv = dev->priv;
        u8 reg = RTL818X_EEPROM_CMD_PROGRAM;

        if (eeprom->reg_data_in)
                reg |= RTL818X_EEPROM_CMD_WRITE;
        if (eeprom->reg_data_out)
                reg |= RTL818X_EEPROM_CMD_READ;
        if (eeprom->reg_data_clock)
                reg |= RTL818X_EEPROM_CMD_CK;
        if (eeprom->reg_chip_select)
                reg |= RTL818X_EEPROM_CMD_CS;

        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, reg);
        udelay(10);
}

static int rtl8187_probe(struct usb_interface *intf,
                                   const struct usb_device_id *id)
{
        struct usb_device *udev = interface_to_usbdev(intf);
        struct ieee80211_hw *dev;
        struct rtl8187_priv *priv;
        struct eeprom_93cx6 eeprom;
        struct ieee80211_channel *channel;
        const char *chip_name;
        u16 txpwr, reg;
        u16 product_id = le16_to_cpu(udev->descriptor.idProduct);
        int err, i;
        u8 mac_addr[ETH_ALEN];

        dev = ieee80211_alloc_hw(sizeof(*priv), &rtl8187_ops);
        if (!dev) {
                printk(KERN_ERR "rtl8187: ieee80211 alloc failed\n");
                return -ENOMEM;
        }

        priv = dev->priv;
        priv->is_rtl8187b = (id->driver_info == DEVICE_RTL8187B);

        /* allocate "DMA aware" buffer for register accesses */
        priv->io_dmabuf = kmalloc_obj(*priv->io_dmabuf);
        if (!priv->io_dmabuf) {
                err = -ENOMEM;
                goto err_free_dev;
        }
        mutex_init(&priv->io_mutex);
        mutex_init(&priv->conf_mutex);

        SET_IEEE80211_DEV(dev, &intf->dev);
        usb_set_intfdata(intf, dev);
        priv->udev = udev;

        usb_get_dev(udev);

        skb_queue_head_init(&priv->rx_queue);

        BUILD_BUG_ON(sizeof(priv->channels) != sizeof(rtl818x_channels));
        BUILD_BUG_ON(sizeof(priv->rates) != sizeof(rtl818x_rates));

        memcpy(priv->channels, rtl818x_channels, sizeof(rtl818x_channels));
        memcpy(priv->rates, rtl818x_rates, sizeof(rtl818x_rates));
        priv->map = (struct rtl818x_csr *)0xFF00;

        priv->band.band = NL80211_BAND_2GHZ;
        priv->band.channels = priv->channels;
        priv->band.n_channels = ARRAY_SIZE(rtl818x_channels);
        priv->band.bitrates = priv->rates;
        priv->band.n_bitrates = ARRAY_SIZE(rtl818x_rates);
        dev->wiphy->bands[NL80211_BAND_2GHZ] = &priv->band;


        ieee80211_hw_set(dev, RX_INCLUDES_FCS);
        ieee80211_hw_set(dev, HOST_BROADCAST_PS_BUFFERING);
        ieee80211_hw_set(dev, SIGNAL_DBM);
        /* Initialize rate-control variables */
        dev->max_rates = 1;
        dev->max_rate_tries = RETRY_COUNT;

        eeprom.data = dev;
        eeprom.register_read = rtl8187_eeprom_register_read;
        eeprom.register_write = rtl8187_eeprom_register_write;
        if (rtl818x_ioread32(priv, &priv->map->RX_CONF) & (1 << 6))
                eeprom.width = PCI_EEPROM_WIDTH_93C66;
        else
                eeprom.width = PCI_EEPROM_WIDTH_93C46;

        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
        udelay(10);

        eeprom_93cx6_multiread(&eeprom, RTL8187_EEPROM_MAC_ADDR,
                               (__le16 __force *)mac_addr, 3);
        if (!is_valid_ether_addr(mac_addr)) {
                printk(KERN_WARNING "rtl8187: Invalid hwaddr! Using randomly "
                       "generated MAC address\n");
                eth_random_addr(mac_addr);
        }
        SET_IEEE80211_PERM_ADDR(dev, mac_addr);

        channel = priv->channels;
        for (i = 0; i < 3; i++) {
                eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_1 + i,
                                  &txpwr);
                (*channel++).hw_value = txpwr & 0xFF;
                (*channel++).hw_value = txpwr >> 8;
        }
        for (i = 0; i < 2; i++) {
                eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_4 + i,
                                  &txpwr);
                (*channel++).hw_value = txpwr & 0xFF;
                (*channel++).hw_value = txpwr >> 8;
        }

        eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_BASE,
                          &priv->txpwr_base);

        reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~1;
        rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1);
        /* 0 means asic B-cut, we should use SW 3 wire
         * bit-by-bit banging for radio. 1 means we can use
         * USB specific request to write radio registers */
        priv->asic_rev = rtl818x_ioread8(priv, (u8 *)0xFFFE) & 0x3;
        rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg);
        rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);

        if (!priv->is_rtl8187b) {
                u32 reg32;
                reg32 = rtl818x_ioread32(priv, &priv->map->TX_CONF);
                reg32 &= RTL818X_TX_CONF_HWVER_MASK;
                switch (reg32) {
                case RTL818X_TX_CONF_R8187vD_B:
                        /* Some RTL8187B devices have a USB ID of 0x8187
                         * detect them here */
                        chip_name = "RTL8187BvB(early)";
                        priv->is_rtl8187b = 1;
                        priv->hw_rev = RTL8187BvB;
                        break;
                case RTL818X_TX_CONF_R8187vD:
                        chip_name = "RTL8187vD";
                        break;
                default:
                        chip_name = "RTL8187vB (default)";
                }
       } else {
                /*
                 * Force USB request to write radio registers for 8187B, Realtek
                 * only uses it in their sources
                 */
                /*if (priv->asic_rev == 0) {
                        printk(KERN_WARNING "rtl8187: Forcing use of USB "
                               "requests to write to radio registers\n");
                        priv->asic_rev = 1;
                }*/
                switch (rtl818x_ioread8(priv, (u8 *)0xFFE1)) {
                case RTL818X_R8187B_B:
                        chip_name = "RTL8187BvB";
                        priv->hw_rev = RTL8187BvB;
                        break;
                case RTL818X_R8187B_D:
                        chip_name = "RTL8187BvD";
                        priv->hw_rev = RTL8187BvD;
                        break;
                case RTL818X_R8187B_E:
                        chip_name = "RTL8187BvE";
                        priv->hw_rev = RTL8187BvE;
                        break;
                default:
                        chip_name = "RTL8187BvB (default)";
                        priv->hw_rev = RTL8187BvB;
                }
        }

        if (!priv->is_rtl8187b) {
                for (i = 0; i < 2; i++) {
                        eeprom_93cx6_read(&eeprom,
                                          RTL8187_EEPROM_TXPWR_CHAN_6 + i,
                                          &txpwr);
                        (*channel++).hw_value = txpwr & 0xFF;
                        (*channel++).hw_value = txpwr >> 8;
                }
        } else {
                eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_6,
                                  &txpwr);
                (*channel++).hw_value = txpwr & 0xFF;

                eeprom_93cx6_read(&eeprom, 0x0A, &txpwr);
                (*channel++).hw_value = txpwr & 0xFF;

                eeprom_93cx6_read(&eeprom, 0x1C, &txpwr);
                (*channel++).hw_value = txpwr & 0xFF;
                (*channel++).hw_value = txpwr >> 8;
        }
        /* Handle the differing rfkill GPIO bit in different models */
        priv->rfkill_mask = RFKILL_MASK_8187_89_97;
        if (product_id == 0x8197 || product_id == 0x8198) {
                eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_SELECT_GPIO, &reg);
                if (reg & 0xFF00)
                        priv->rfkill_mask = RFKILL_MASK_8198;
        }
        dev->vif_data_size = sizeof(struct rtl8187_vif);
        dev->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) |
                                      BIT(NL80211_IFTYPE_ADHOC) ;

        wiphy_ext_feature_set(dev->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);

        if ((id->driver_info == DEVICE_RTL8187) && priv->is_rtl8187b)
                printk(KERN_INFO "rtl8187: inconsistency between id with OEM"
                       " info!\n");

        priv->rf = rtl8187_detect_rf(dev);
        dev->extra_tx_headroom = (!priv->is_rtl8187b) ?
                                  sizeof(struct rtl8187_tx_hdr) :
                                  sizeof(struct rtl8187b_tx_hdr);
        if (!priv->is_rtl8187b)
                dev->queues = 1;
        else
                dev->queues = 4;

        err = ieee80211_register_hw(dev);
        if (err) {
                printk(KERN_ERR "rtl8187: Cannot register device\n");
                goto err_free_dmabuf;
        }
        skb_queue_head_init(&priv->b_tx_status.queue);

        wiphy_info(dev->wiphy, "hwaddr %pM, %s V%d + %s, rfkill mask %d\n",
                   mac_addr, chip_name, priv->asic_rev, priv->rf->name,
                   priv->rfkill_mask);

#ifdef CONFIG_RTL8187_LEDS
        eeprom_93cx6_read(&eeprom, 0x3F, &reg);
        reg &= 0xFF;
        rtl8187_leds_init(dev, reg);
#endif
        rtl8187_rfkill_init(dev);

        return 0;

 err_free_dmabuf:
        kfree(priv->io_dmabuf);
        usb_set_intfdata(intf, NULL);
        usb_put_dev(udev);
 err_free_dev:
        ieee80211_free_hw(dev);
        return err;
}

static void rtl8187_disconnect(struct usb_interface *intf)
{
        struct ieee80211_hw *dev = usb_get_intfdata(intf);
        struct rtl8187_priv *priv;

        if (!dev)
                return;

#ifdef CONFIG_RTL8187_LEDS
        rtl8187_leds_exit(dev);
#endif
        rtl8187_rfkill_exit(dev);
        ieee80211_unregister_hw(dev);

        priv = dev->priv;
        usb_reset_device(priv->udev);
        usb_put_dev(interface_to_usbdev(intf));
        kfree(priv->io_dmabuf);
        ieee80211_free_hw(dev);
}

static struct usb_driver rtl8187_driver = {
        .name           = KBUILD_MODNAME,
        .id_table       = rtl8187_table,
        .probe          = rtl8187_probe,
        .disconnect     = rtl8187_disconnect,
        .disable_hub_initiated_lpm = 1,
};

module_usb_driver(rtl8187_driver);