/*
 * Intel 82860 Memory Controller kernel module
 * (C) 2005 Red Hat (http://www.redhat.com)
 * This file may be distributed under the terms of the
 * GNU General Public License.
 *
 * Written by Ben Woodard <woodard@redhat.com>
 * shamelessly copied from and based upon the edac_i82875 driver
 * by Thayne Harbaugh of Linux Networx. (http://lnxi.com)
 */

#include <linux/module.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/pci_ids.h>
#include <linux/edac.h>
#include "edac_module.h"

#define EDAC_MOD_STR    "i82860_edac"

#define i82860_printk(level, fmt, arg...) \
        edac_printk(level, "i82860", fmt, ##arg)

#define i82860_mc_printk(mci, level, fmt, arg...) \
        edac_mc_chipset_printk(mci, level, "i82860", fmt, ##arg)

#ifndef PCI_DEVICE_ID_INTEL_82860_0
#define PCI_DEVICE_ID_INTEL_82860_0     0x2531
#endif                          /* PCI_DEVICE_ID_INTEL_82860_0 */

#define I82860_MCHCFG 0x50
#define I82860_GBA 0x60
#define I82860_GBA_MASK 0x7FF
#define I82860_GBA_SHIFT 24
#define I82860_ERRSTS 0xC8
#define I82860_EAP 0xE4
#define I82860_DERRCTL_STS 0xE2

enum i82860_chips {
        I82860 = 0,
};

struct i82860_dev_info {
        const char *ctl_name;
};

struct i82860_error_info {
        u16 errsts;
        u32 eap;
        u16 derrsyn;
        u16 errsts2;
};

static const struct i82860_dev_info i82860_devs[] = {
        [I82860] = {
                .ctl_name = "i82860"},
};

static struct pci_dev *mci_pdev;        /* init dev: in case that AGP code
                                         * has already registered driver
                                         */
static struct edac_pci_ctl_info *i82860_pci;

static void i82860_get_error_info(struct mem_ctl_info *mci,
                                struct i82860_error_info *info)
{
        struct pci_dev *pdev;

        pdev = to_pci_dev(mci->pdev);

        /*
         * This is a mess because there is no atomic way to read all the
         * registers at once and the registers can transition from CE being
         * overwritten by UE.
         */
        pci_read_config_word(pdev, I82860_ERRSTS, &info->errsts);
        pci_read_config_dword(pdev, I82860_EAP, &info->eap);
        pci_read_config_word(pdev, I82860_DERRCTL_STS, &info->derrsyn);
        pci_read_config_word(pdev, I82860_ERRSTS, &info->errsts2);

        pci_write_bits16(pdev, I82860_ERRSTS, 0x0003, 0x0003);

        /*
         * If the error is the same for both reads then the first set of reads
         * is valid.  If there is a change then there is a CE no info and the
         * second set of reads is valid and should be UE info.
         */
        if (!(info->errsts2 & 0x0003))
                return;

        if ((info->errsts ^ info->errsts2) & 0x0003) {
                pci_read_config_dword(pdev, I82860_EAP, &info->eap);
                pci_read_config_word(pdev, I82860_DERRCTL_STS, &info->derrsyn);
        }
}

static int i82860_process_error_info(struct mem_ctl_info *mci,
                                struct i82860_error_info *info,
                                int handle_errors)
{
        struct dimm_info *dimm;
        int row;

        if (!(info->errsts2 & 0x0003))
                return 0;

        if (!handle_errors)
                return 1;

        if ((info->errsts ^ info->errsts2) & 0x0003) {
                edac_mc_handle_error(HW_EVENT_ERR_UNCORRECTED, mci, 1, 0, 0, 0,
                                     -1, -1, -1, "UE overwrote CE", "");
                info->errsts = info->errsts2;
        }

        info->eap >>= PAGE_SHIFT;
        row = edac_mc_find_csrow_by_page(mci, info->eap);
        dimm = mci->csrows[row]->channels[0]->dimm;

        if (info->errsts & 0x0002)
                edac_mc_handle_error(HW_EVENT_ERR_UNCORRECTED, mci, 1,
                                     info->eap, 0, 0,
                                     dimm->location[0], dimm->location[1], -1,
                                     "i82860 UE", "");
        else
                edac_mc_handle_error(HW_EVENT_ERR_CORRECTED, mci, 1,
                                     info->eap, 0, info->derrsyn,
                                     dimm->location[0], dimm->location[1], -1,
                                     "i82860 CE", "");

        return 1;
}

static void i82860_check(struct mem_ctl_info *mci)
{
        struct i82860_error_info info;

        i82860_get_error_info(mci, &info);
        i82860_process_error_info(mci, &info, 1);
}

static void i82860_init_csrows(struct mem_ctl_info *mci, struct pci_dev *pdev)
{
        unsigned long last_cumul_size;
        u16 mchcfg_ddim;        /* DRAM Data Integrity Mode 0=none, 2=edac */
        u16 value;
        u32 cumul_size;
        struct csrow_info *csrow;
        struct dimm_info *dimm;
        int index;

        pci_read_config_word(pdev, I82860_MCHCFG, &mchcfg_ddim);
        mchcfg_ddim = mchcfg_ddim & 0x180;
        last_cumul_size = 0;

        /* The group row boundary (GRA) reg values are boundary address
         * for each DRAM row with a granularity of 16MB.  GRA regs are
         * cumulative; therefore GRA15 will contain the total memory contained
         * in all eight rows.
         */
        for (index = 0; index < mci->nr_csrows; index++) {
                csrow = mci->csrows[index];
                dimm = csrow->channels[0]->dimm;

                pci_read_config_word(pdev, I82860_GBA + index * 2, &value);
                cumul_size = (value & I82860_GBA_MASK) <<
                        (I82860_GBA_SHIFT - PAGE_SHIFT);
                edac_dbg(3, "(%d) cumul_size 0x%x\n", index, cumul_size);

                if (cumul_size == last_cumul_size)
                        continue;       /* not populated */

                csrow->first_page = last_cumul_size;
                csrow->last_page = cumul_size - 1;
                dimm->nr_pages = cumul_size - last_cumul_size;
                last_cumul_size = cumul_size;
                dimm->grain = 1 << 12;  /* I82860_EAP has 4KiB reolution */
                dimm->mtype = MEM_RMBS;
                dimm->dtype = DEV_UNKNOWN;
                dimm->edac_mode = mchcfg_ddim ? EDAC_SECDED : EDAC_NONE;
        }
}

static int i82860_probe1(struct pci_dev *pdev, int dev_idx)
{
        struct mem_ctl_info *mci;
        struct edac_mc_layer layers[2];
        struct i82860_error_info discard;

        /*
         * RDRAM has channels but these don't map onto the csrow abstraction.
         * According with the datasheet, there are 2 Rambus channels, supporting
         * up to 16 direct RDRAM devices.
         * The device groups from the GRA registers seem to map reasonably
         * well onto the notion of a chip select row.
         * There are 16 GRA registers and since the name is associated with
         * the channel and the GRA registers map to physical devices so we are
         * going to make 1 channel for group.
         */
        layers[0].type = EDAC_MC_LAYER_CHANNEL;
        layers[0].size = 2;
        layers[0].is_virt_csrow = true;
        layers[1].type = EDAC_MC_LAYER_SLOT;
        layers[1].size = 8;
        layers[1].is_virt_csrow = true;
        mci = edac_mc_alloc(0, ARRAY_SIZE(layers), layers, 0);
        if (!mci)
                return -ENOMEM;

        edac_dbg(3, "init mci\n");
        mci->pdev = &pdev->dev;
        mci->mtype_cap = MEM_FLAG_DDR;
        mci->edac_ctl_cap = EDAC_FLAG_NONE | EDAC_FLAG_SECDED;
        /* I"m not sure about this but I think that all RDRAM is SECDED */
        mci->edac_cap = EDAC_FLAG_SECDED;
        mci->mod_name = EDAC_MOD_STR;
        mci->ctl_name = i82860_devs[dev_idx].ctl_name;
        mci->dev_name = pci_name(pdev);
        mci->edac_check = i82860_check;
        mci->ctl_page_to_phys = NULL;
        i82860_init_csrows(mci, pdev);
        i82860_get_error_info(mci, &discard);   /* clear counters */

        /* Here we assume that we will never see multiple instances of this
         * type of memory controller.  The ID is therefore hardcoded to 0.
         */
        if (edac_mc_add_mc(mci)) {
                edac_dbg(3, "failed edac_mc_add_mc()\n");
                goto fail;
        }

        /* allocating generic PCI control info */
        i82860_pci = edac_pci_create_generic_ctl(&pdev->dev, EDAC_MOD_STR);
        if (!i82860_pci) {
                printk(KERN_WARNING
                        "%s(): Unable to create PCI control\n",
                        __func__);
                printk(KERN_WARNING
                        "%s(): PCI error report via EDAC not setup\n",
                        __func__);
        }

        /* get this far and it's successful */
        edac_dbg(3, "success\n");

        return 0;

fail:
        edac_mc_free(mci);
        return -ENODEV;
}

/* returns count (>= 0), or negative on error */
static int i82860_init_one(struct pci_dev *pdev,
                           const struct pci_device_id *ent)
{
        int rc;

        edac_dbg(0, "\n");
        i82860_printk(KERN_INFO, "i82860 init one\n");

        if (pci_enable_device(pdev) < 0)
                return -EIO;

        rc = i82860_probe1(pdev, ent->driver_data);

        if (rc == 0)
                mci_pdev = pci_dev_get(pdev);

        return rc;
}

static void i82860_remove_one(struct pci_dev *pdev)
{
        struct mem_ctl_info *mci;

        edac_dbg(0, "\n");

        if (i82860_pci)
                edac_pci_release_generic_ctl(i82860_pci);

        if ((mci = edac_mc_del_mc(&pdev->dev)) == NULL)
                return;

        edac_mc_free(mci);
}

static const struct pci_device_id i82860_pci_tbl[] = {
        {
         PCI_VEND_DEV(INTEL, 82860_0), PCI_ANY_ID, PCI_ANY_ID, 0, 0,
         I82860},
        {
         0,
         }                      /* 0 terminated list. */
};

MODULE_DEVICE_TABLE(pci, i82860_pci_tbl);

static struct pci_driver i82860_driver = {
        .name = EDAC_MOD_STR,
        .probe = i82860_init_one,
        .remove = i82860_remove_one,
        .id_table = i82860_pci_tbl,
};

static int __init i82860_init(void)
{
        int pci_rc;

        edac_dbg(3, "\n");

       /* Ensure that the OPSTATE is set correctly for POLL or NMI */
       opstate_init();

        if ((pci_rc = pci_register_driver(&i82860_driver)) < 0)
                goto fail0;

        if (!mci_pdev) {
                mci_pdev = pci_get_device(PCI_VENDOR_ID_INTEL,
                                        PCI_DEVICE_ID_INTEL_82860_0, NULL);

                if (mci_pdev == NULL) {
                        edac_dbg(0, "860 pci_get_device fail\n");
                        pci_rc = -ENODEV;
                        goto fail1;
                }

                pci_rc = i82860_init_one(mci_pdev, i82860_pci_tbl);

                if (pci_rc < 0) {
                        edac_dbg(0, "860 init fail\n");
                        pci_rc = -ENODEV;
                        goto fail1;
                }
        }

        return 0;

fail1:
        pci_unregister_driver(&i82860_driver);

fail0:
        pci_dev_put(mci_pdev);
        return pci_rc;
}

static void __exit i82860_exit(void)
{
        edac_dbg(3, "\n");
        pci_unregister_driver(&i82860_driver);
        pci_dev_put(mci_pdev);
}

module_init(i82860_init);
module_exit(i82860_exit);

MODULE_LICENSE("GPL");
MODULE_AUTHOR("Red Hat Inc. (http://www.redhat.com) Ben Woodard <woodard@redhat.com>");
MODULE_DESCRIPTION("ECC support for Intel 82860 memory hub controllers");

module_param(edac_op_state, int, 0444);
MODULE_PARM_DESC(edac_op_state, "EDAC Error Reporting state: 0=Poll,1=NMI");