// SPDX-License-Identifier: GPL-2.0
/* Copyright(c) 2013 - 2018 Intel Corporation. */

#include <linux/ptp_classify.h>
#include <linux/posix-clock.h>
#include "i40e.h"
#include "i40e_devids.h"

/* The XL710 timesync is very much like Intel's 82599 design when it comes to
 * the fundamental clock design. However, the clock operations are much simpler
 * in the XL710 because the device supports a full 64 bits of nanoseconds.
 * Because the field is so wide, we can forgo the cycle counter and just
 * operate with the nanosecond field directly without fear of overflow.
 *
 * Much like the 82599, the update period is dependent upon the link speed:
 * At 40Gb, 25Gb, or no link, the period is 1.6ns.
 * At 10Gb or 5Gb link, the period is multiplied by 2. (3.2ns)
 * At 1Gb link, the period is multiplied by 20. (32ns)
 * 1588 functionality is not supported at 100Mbps.
 */
#define I40E_PTP_40GB_INCVAL            0x0199999999ULL
#define I40E_PTP_10GB_INCVAL_MULT       2
#define I40E_PTP_5GB_INCVAL_MULT        2
#define I40E_PTP_1GB_INCVAL_MULT        20
#define I40E_ISGN                       0x80000000

#define I40E_PRTTSYN_CTL1_TSYNTYPE_V1  BIT(I40E_PRTTSYN_CTL1_TSYNTYPE_SHIFT)
#define I40E_PRTTSYN_CTL1_TSYNTYPE_V2  (2 << \
                                        I40E_PRTTSYN_CTL1_TSYNTYPE_SHIFT)
#define I40E_SUBDEV_ID_25G_PTP_PIN      0xB

enum i40e_ptp_pin {
        SDP3_2 = 0,
        SDP3_3,
        GPIO_4
};

enum i40e_can_set_pins {
        CANT_DO_PINS = -1,
        CAN_SET_PINS,
        CAN_DO_PINS
};

static struct ptp_pin_desc sdp_desc[] = {
        /* name     idx      func      chan */
        {"SDP3_2", SDP3_2, PTP_PF_NONE, 0},
        {"SDP3_3", SDP3_3, PTP_PF_NONE, 1},
        {"GPIO_4", GPIO_4, PTP_PF_NONE, 1},
};

enum i40e_ptp_gpio_pin_state {
        end = -2,
        invalid,
        off,
        in_A,
        in_B,
        out_A,
        out_B,
};

static const char * const i40e_ptp_gpio_pin_state2str[] = {
        "off", "in_A", "in_B", "out_A", "out_B"
};

enum i40e_ptp_led_pin_state {
        led_end = -2,
        low = 0,
        high,
};

struct i40e_ptp_pins_settings {
        enum i40e_ptp_gpio_pin_state sdp3_2;
        enum i40e_ptp_gpio_pin_state sdp3_3;
        enum i40e_ptp_gpio_pin_state gpio_4;
        enum i40e_ptp_led_pin_state led2_0;
        enum i40e_ptp_led_pin_state led2_1;
        enum i40e_ptp_led_pin_state led3_0;
        enum i40e_ptp_led_pin_state led3_1;
};

static const struct i40e_ptp_pins_settings
        i40e_ptp_pin_led_allowed_states[] = {
        {off,   off,    off,            high,   high,   high,   high},
        {off,   in_A,   off,            high,   high,   high,   low},
        {off,   out_A,  off,            high,   low,    high,   high},
        {off,   in_B,   off,            high,   high,   high,   low},
        {off,   out_B,  off,            high,   low,    high,   high},
        {in_A,  off,    off,            high,   high,   high,   low},
        {in_A,  in_B,   off,            high,   high,   high,   low},
        {in_A,  out_B,  off,            high,   low,    high,   high},
        {out_A, off,    off,            high,   low,    high,   high},
        {out_A, in_B,   off,            high,   low,    high,   high},
        {in_B,  off,    off,            high,   high,   high,   low},
        {in_B,  in_A,   off,            high,   high,   high,   low},
        {in_B,  out_A,  off,            high,   low,    high,   high},
        {out_B, off,    off,            high,   low,    high,   high},
        {out_B, in_A,   off,            high,   low,    high,   high},
        {off,   off,    in_A,           high,   high,   low,    high},
        {off,   out_A,  in_A,           high,   low,    low,    high},
        {off,   in_B,   in_A,           high,   high,   low,    low},
        {off,   out_B,  in_A,           high,   low,    low,    high},
        {out_A, off,    in_A,           high,   low,    low,    high},
        {out_A, in_B,   in_A,           high,   low,    low,    high},
        {in_B,  off,    in_A,           high,   high,   low,    low},
        {in_B,  out_A,  in_A,           high,   low,    low,    high},
        {out_B, off,    in_A,           high,   low,    low,    high},
        {off,   off,    out_A,          low,    high,   high,   high},
        {off,   in_A,   out_A,          low,    high,   high,   low},
        {off,   in_B,   out_A,          low,    high,   high,   low},
        {off,   out_B,  out_A,          low,    low,    high,   high},
        {in_A,  off,    out_A,          low,    high,   high,   low},
        {in_A,  in_B,   out_A,          low,    high,   high,   low},
        {in_A,  out_B,  out_A,          low,    low,    high,   high},
        {in_B,  off,    out_A,          low,    high,   high,   low},
        {in_B,  in_A,   out_A,          low,    high,   high,   low},
        {out_B, off,    out_A,          low,    low,    high,   high},
        {out_B, in_A,   out_A,          low,    low,    high,   high},
        {off,   off,    in_B,           high,   high,   low,    high},
        {off,   in_A,   in_B,           high,   high,   low,    low},
        {off,   out_A,  in_B,           high,   low,    low,    high},
        {off,   out_B,  in_B,           high,   low,    low,    high},
        {in_A,  off,    in_B,           high,   high,   low,    low},
        {in_A,  out_B,  in_B,           high,   low,    low,    high},
        {out_A, off,    in_B,           high,   low,    low,    high},
        {out_B, off,    in_B,           high,   low,    low,    high},
        {out_B, in_A,   in_B,           high,   low,    low,    high},
        {off,   off,    out_B,          low,    high,   high,   high},
        {off,   in_A,   out_B,          low,    high,   high,   low},
        {off,   out_A,  out_B,          low,    low,    high,   high},
        {off,   in_B,   out_B,          low,    high,   high,   low},
        {in_A,  off,    out_B,          low,    high,   high,   low},
        {in_A,  in_B,   out_B,          low,    high,   high,   low},
        {out_A, off,    out_B,          low,    low,    high,   high},
        {out_A, in_B,   out_B,          low,    low,    high,   high},
        {in_B,  off,    out_B,          low,    high,   high,   low},
        {in_B,  in_A,   out_B,          low,    high,   high,   low},
        {in_B,  out_A,  out_B,          low,    low,    high,   high},
        {end,   end,    end,    led_end, led_end, led_end, led_end}
};

static int i40e_ptp_set_pins(struct i40e_pf *pf,
                             struct i40e_ptp_pins_settings *pins);

/**
 * i40e_ptp_extts0_work - workqueue task function
 * @work: workqueue task structure
 *
 * Service for PTP external clock event
 **/
static void i40e_ptp_extts0_work(struct work_struct *work)
{
        struct i40e_pf *pf = container_of(work, struct i40e_pf,
                                          ptp_extts0_work);
        struct i40e_hw *hw = &pf->hw;
        struct ptp_clock_event event;
        u32 hi, lo;

        /* Event time is captured by one of the two matched registers
         *      PRTTSYN_EVNT_L: 32 LSB of sampled time event
         *      PRTTSYN_EVNT_H: 32 MSB of sampled time event
         * Event is defined in PRTTSYN_EVNT_0 register
         */
        lo = rd32(hw, I40E_PRTTSYN_EVNT_L(0));
        hi = rd32(hw, I40E_PRTTSYN_EVNT_H(0));

        event.timestamp = (((u64)hi) << 32) | lo;

        event.type = PTP_CLOCK_EXTTS;
        event.index = hw->pf_id;

        /* fire event */
        ptp_clock_event(pf->ptp_clock, &event);
}

/**
 * i40e_is_ptp_pin_dev - check if device supports PTP pins
 * @hw: pointer to the hardware structure
 *
 * Return true if device supports PTP pins, false otherwise.
 **/
static bool i40e_is_ptp_pin_dev(struct i40e_hw *hw)
{
        return hw->device_id == I40E_DEV_ID_25G_SFP28 &&
               hw->subsystem_device_id == I40E_SUBDEV_ID_25G_PTP_PIN;
}

/**
 * i40e_can_set_pins - check possibility of manipulating the pins
 * @pf: board private structure
 *
 * Check if all conditions are satisfied to manipulate PTP pins.
 * Return CAN_SET_PINS if pins can be set on a specific PF or
 * return CAN_DO_PINS if pins can be manipulated within a NIC or
 * return CANT_DO_PINS otherwise.
 **/
static enum i40e_can_set_pins i40e_can_set_pins(struct i40e_pf *pf)
{
        if (!i40e_is_ptp_pin_dev(&pf->hw)) {
                dev_warn(&pf->pdev->dev,
                         "PTP external clock not supported.\n");
                return CANT_DO_PINS;
        }

        if (!pf->ptp_pins) {
                dev_warn(&pf->pdev->dev,
                         "PTP PIN manipulation not allowed.\n");
                return CANT_DO_PINS;
        }

        if (pf->hw.pf_id) {
                dev_warn(&pf->pdev->dev,
                         "PTP PINs should be accessed via PF0.\n");
                return CAN_DO_PINS;
        }

        return CAN_SET_PINS;
}

/**
 * i40_ptp_reset_timing_events - Reset PTP timing events
 * @pf: Board private structure
 *
 * This function resets timing events for pf.
 **/
static void i40_ptp_reset_timing_events(struct i40e_pf *pf)
{
        u32 i;

        spin_lock_bh(&pf->ptp_rx_lock);
        for (i = 0; i <= I40E_PRTTSYN_RXTIME_L_MAX_INDEX; i++) {
                /* reading and automatically clearing timing events registers */
                rd32(&pf->hw, I40E_PRTTSYN_RXTIME_L(i));
                rd32(&pf->hw, I40E_PRTTSYN_RXTIME_H(i));
                pf->latch_events[i] = 0;
        }
        /* reading and automatically clearing timing events registers */
        rd32(&pf->hw, I40E_PRTTSYN_TXTIME_L);
        rd32(&pf->hw, I40E_PRTTSYN_TXTIME_H);

        pf->tx_hwtstamp_timeouts = 0;
        pf->tx_hwtstamp_skipped = 0;
        pf->rx_hwtstamp_cleared = 0;
        pf->latch_event_flags = 0;
        spin_unlock_bh(&pf->ptp_rx_lock);
}

/**
 * i40e_ptp_verify - check pins
 * @ptp: ptp clock
 * @pin: pin index
 * @func: assigned function
 * @chan: channel
 *
 * Check pins consistency.
 * Return 0 on success or error on failure.
 **/
static int i40e_ptp_verify(struct ptp_clock_info *ptp, unsigned int pin,
                           enum ptp_pin_function func, unsigned int chan)
{
        switch (func) {
        case PTP_PF_NONE:
        case PTP_PF_EXTTS:
        case PTP_PF_PEROUT:
                break;
        case PTP_PF_PHYSYNC:
                return -EOPNOTSUPP;
        }
        return 0;
}

/**
 * i40e_ptp_read - Read the PHC time from the device
 * @pf: Board private structure
 * @ts: timespec structure to hold the current time value
 * @sts: structure to hold the system time before and after reading the PHC
 *
 * This function reads the PRTTSYN_TIME registers and stores them in a
 * timespec. However, since the registers are 64 bits of nanoseconds, we must
 * convert the result to a timespec before we can return.
 **/
static void i40e_ptp_read(struct i40e_pf *pf, struct timespec64 *ts,
                          struct ptp_system_timestamp *sts)
{
        struct i40e_hw *hw = &pf->hw;
        u32 hi, lo;
        u64 ns;

        /* The timer latches on the lowest register read. */
        ptp_read_system_prets(sts);
        lo = rd32(hw, I40E_PRTTSYN_TIME_L);
        ptp_read_system_postts(sts);
        hi = rd32(hw, I40E_PRTTSYN_TIME_H);

        ns = (((u64)hi) << 32) | lo;

        *ts = ns_to_timespec64(ns);
}

/**
 * i40e_ptp_write - Write the PHC time to the device
 * @pf: Board private structure
 * @ts: timespec structure that holds the new time value
 *
 * This function writes the PRTTSYN_TIME registers with the user value. Since
 * we receive a timespec from the stack, we must convert that timespec into
 * nanoseconds before programming the registers.
 **/
static void i40e_ptp_write(struct i40e_pf *pf, const struct timespec64 *ts)
{
        struct i40e_hw *hw = &pf->hw;
        u64 ns = timespec64_to_ns(ts);

        /* The timer will not update until the high register is written, so
         * write the low register first.
         */
        wr32(hw, I40E_PRTTSYN_TIME_L, ns & 0xFFFFFFFF);
        wr32(hw, I40E_PRTTSYN_TIME_H, ns >> 32);
}

/**
 * i40e_ptp_convert_to_hwtstamp - Convert device clock to system time
 * @hwtstamps: Timestamp structure to update
 * @timestamp: Timestamp from the hardware
 *
 * We need to convert the NIC clock value into a hwtstamp which can be used by
 * the upper level timestamping functions. Since the timestamp is simply a 64-
 * bit nanosecond value, we can call ns_to_ktime directly to handle this.
 **/
static void i40e_ptp_convert_to_hwtstamp(struct skb_shared_hwtstamps *hwtstamps,
                                         u64 timestamp)
{
        memset(hwtstamps, 0, sizeof(*hwtstamps));

        hwtstamps->hwtstamp = ns_to_ktime(timestamp);
}

/**
 * i40e_ptp_adjfine - Adjust the PHC frequency
 * @ptp: The PTP clock structure
 * @scaled_ppm: Scaled parts per million adjustment from base
 *
 * Adjust the frequency of the PHC by the indicated delta from the base
 * frequency.
 *
 * Scaled parts per million is ppm with a 16 bit binary fractional field.
 **/
static int i40e_ptp_adjfine(struct ptp_clock_info *ptp, long scaled_ppm)
{
        struct i40e_pf *pf = container_of(ptp, struct i40e_pf, ptp_caps);
        struct i40e_hw *hw = &pf->hw;
        u64 adj, base_adj;

        smp_mb(); /* Force any pending update before accessing. */
        base_adj = I40E_PTP_40GB_INCVAL * READ_ONCE(pf->ptp_adj_mult);

        adj = adjust_by_scaled_ppm(base_adj, scaled_ppm);

        wr32(hw, I40E_PRTTSYN_INC_L, adj & 0xFFFFFFFF);
        wr32(hw, I40E_PRTTSYN_INC_H, adj >> 32);

        return 0;
}

/**
 * i40e_ptp_set_1pps_signal_hw - configure 1PPS PTP signal for pins
 * @pf: the PF private data structure
 *
 * Configure 1PPS signal used for PTP pins
 **/
static void i40e_ptp_set_1pps_signal_hw(struct i40e_pf *pf)
{
        struct i40e_hw *hw = &pf->hw;
        struct timespec64 now;
        u64 ns;

        wr32(hw, I40E_PRTTSYN_AUX_0(1), 0);
        wr32(hw, I40E_PRTTSYN_AUX_1(1), I40E_PRTTSYN_AUX_1_INSTNT);
        wr32(hw, I40E_PRTTSYN_AUX_0(1), I40E_PRTTSYN_AUX_0_OUT_ENABLE);

        i40e_ptp_read(pf, &now, NULL);
        now.tv_sec += I40E_PTP_2_SEC_DELAY;
        now.tv_nsec = 0;
        ns = timespec64_to_ns(&now);

        /* I40E_PRTTSYN_TGT_L(1) */
        wr32(hw, I40E_PRTTSYN_TGT_L(1), ns & 0xFFFFFFFF);
        /* I40E_PRTTSYN_TGT_H(1) */
        wr32(hw, I40E_PRTTSYN_TGT_H(1), ns >> 32);
        wr32(hw, I40E_PRTTSYN_CLKO(1), I40E_PTP_HALF_SECOND);
        wr32(hw, I40E_PRTTSYN_AUX_1(1), I40E_PRTTSYN_AUX_1_INSTNT);
        wr32(hw, I40E_PRTTSYN_AUX_0(1),
             I40E_PRTTSYN_AUX_0_OUT_ENABLE_CLK_MOD);
}

/**
 * i40e_ptp_adjtime - Adjust the PHC time
 * @ptp: The PTP clock structure
 * @delta: Offset in nanoseconds to adjust the PHC time by
 *
 * Adjust the current clock time by a delta specified in nanoseconds.
 **/
static int i40e_ptp_adjtime(struct ptp_clock_info *ptp, s64 delta)
{
        struct i40e_pf *pf = container_of(ptp, struct i40e_pf, ptp_caps);
        struct i40e_hw *hw = &pf->hw;

        mutex_lock(&pf->tmreg_lock);

        if (delta > -999999900LL && delta < 999999900LL) {
                int neg_adj = 0;
                u32 timadj;
                u64 tohw;

                if (delta < 0) {
                        neg_adj = 1;
                        tohw = -delta;
                } else {
                        tohw = delta;
                }

                timadj = tohw & 0x3FFFFFFF;
                if (neg_adj)
                        timadj |= I40E_ISGN;
                wr32(hw, I40E_PRTTSYN_ADJ, timadj);
        } else {
                struct timespec64 then, now;

                then = ns_to_timespec64(delta);
                i40e_ptp_read(pf, &now, NULL);
                now = timespec64_add(now, then);
                i40e_ptp_write(pf, (const struct timespec64 *)&now);
                i40e_ptp_set_1pps_signal_hw(pf);
        }

        mutex_unlock(&pf->tmreg_lock);

        return 0;
}

/**
 * i40e_ptp_gettimex - Get the time of the PHC
 * @ptp: The PTP clock structure
 * @ts: timespec structure to hold the current time value
 * @sts: structure to hold the system time before and after reading the PHC
 *
 * Read the device clock and return the correct value on ns, after converting it
 * into a timespec struct.
 **/
static int i40e_ptp_gettimex(struct ptp_clock_info *ptp, struct timespec64 *ts,
                             struct ptp_system_timestamp *sts)
{
        struct i40e_pf *pf = container_of(ptp, struct i40e_pf, ptp_caps);

        mutex_lock(&pf->tmreg_lock);
        i40e_ptp_read(pf, ts, sts);
        mutex_unlock(&pf->tmreg_lock);

        return 0;
}

/**
 * i40e_ptp_settime - Set the time of the PHC
 * @ptp: The PTP clock structure
 * @ts: timespec64 structure that holds the new time value
 *
 * Set the device clock to the user input value. The conversion from timespec
 * to ns happens in the write function.
 **/
static int i40e_ptp_settime(struct ptp_clock_info *ptp,
                            const struct timespec64 *ts)
{
        struct i40e_pf *pf = container_of(ptp, struct i40e_pf, ptp_caps);

        mutex_lock(&pf->tmreg_lock);
        i40e_ptp_write(pf, ts);
        mutex_unlock(&pf->tmreg_lock);

        return 0;
}

/**
 * i40e_pps_configure - configure PPS events
 * @ptp: ptp clock
 * @rq: clock request
 * @on: status
 *
 * Configure PPS events for external clock source.
 * Return 0 on success or error on failure.
 **/
static int i40e_pps_configure(struct ptp_clock_info *ptp,
                              struct ptp_clock_request *rq,
                              int on)
{
        struct i40e_pf *pf = container_of(ptp, struct i40e_pf, ptp_caps);

        if (!!on)
                i40e_ptp_set_1pps_signal_hw(pf);

        return 0;
}

/**
 * i40e_pin_state - determine PIN state
 * @index: PIN index
 * @func: function assigned to PIN
 *
 * Determine PIN state based on PIN index and function assigned.
 * Return PIN state.
 **/
static enum i40e_ptp_gpio_pin_state i40e_pin_state(int index, int func)
{
        enum i40e_ptp_gpio_pin_state state = off;

        if (index == 0 && func == PTP_PF_EXTTS)
                state = in_A;
        if (index == 1 && func == PTP_PF_EXTTS)
                state = in_B;
        if (index == 0 && func == PTP_PF_PEROUT)
                state = out_A;
        if (index == 1 && func == PTP_PF_PEROUT)
                state = out_B;

        return state;
}

/**
 * i40e_ptp_enable_pin - enable PINs.
 * @pf: private board structure
 * @chan: channel
 * @func: PIN function
 * @on: state
 *
 * Enable PTP pins for external clock source.
 * Return 0 on success or error code on failure.
 **/
static int i40e_ptp_enable_pin(struct i40e_pf *pf, unsigned int chan,
                               enum ptp_pin_function func, int on)
{
        enum i40e_ptp_gpio_pin_state *pin = NULL;
        struct i40e_ptp_pins_settings pins;
        int pin_index;

        /* Use PF0 to set pins. Return success for user space tools */
        if (pf->hw.pf_id)
                return 0;

        /* Preserve previous state of pins that we don't touch */
        pins.sdp3_2 = pf->ptp_pins->sdp3_2;
        pins.sdp3_3 = pf->ptp_pins->sdp3_3;
        pins.gpio_4 = pf->ptp_pins->gpio_4;

        /* To turn on the pin - find the corresponding one based on
         * the given index. To turn the function off - find
         * which pin had it assigned. Don't use ptp_find_pin here
         * because it tries to lock the pincfg_mux which is locked by
         * ptp_pin_store() that calls here.
         */
        if (on) {
                pin_index = ptp_find_pin(pf->ptp_clock, func, chan);
                if (pin_index < 0)
                        return -EBUSY;

                switch (pin_index) {
                case SDP3_2:
                        pin = &pins.sdp3_2;
                        break;
                case SDP3_3:
                        pin = &pins.sdp3_3;
                        break;
                case GPIO_4:
                        pin = &pins.gpio_4;
                        break;
                default:
                        return -EINVAL;
                }

                *pin = i40e_pin_state(chan, func);
        } else {
                pins.sdp3_2 = off;
                pins.sdp3_3 = off;
                pins.gpio_4 = off;
        }

        return i40e_ptp_set_pins(pf, &pins) ? -EINVAL : 0;
}

/**
 * i40e_ptp_feature_enable - Enable external clock pins
 * @ptp: The PTP clock structure
 * @rq: The PTP clock request structure
 * @on: To turn feature on/off
 *
 * Setting on/off PTP PPS feature for pin.
 **/
static int i40e_ptp_feature_enable(struct ptp_clock_info *ptp,
                                   struct ptp_clock_request *rq,
                                   int on)
{
        struct i40e_pf *pf = container_of(ptp, struct i40e_pf, ptp_caps);

        enum ptp_pin_function func;
        unsigned int chan;

        /* TODO: Implement flags handling for EXTTS and PEROUT */
        switch (rq->type) {
        case PTP_CLK_REQ_EXTTS:
                func = PTP_PF_EXTTS;
                chan = rq->extts.index;
                break;
        case PTP_CLK_REQ_PEROUT:
                func = PTP_PF_PEROUT;
                chan = rq->perout.index;
                break;
        case PTP_CLK_REQ_PPS:
                return i40e_pps_configure(ptp, rq, on);
        default:
                return -EOPNOTSUPP;
        }

        return i40e_ptp_enable_pin(pf, chan, func, on);
}

/**
 * i40e_ptp_get_rx_events - Read I40E_PRTTSYN_STAT_1 and latch events
 * @pf: the PF data structure
 *
 * This function reads I40E_PRTTSYN_STAT_1 and updates the corresponding timers
 * for noticed latch events. This allows the driver to keep track of the first
 * time a latch event was noticed which will be used to help clear out Rx
 * timestamps for packets that got dropped or lost.
 *
 * This function will return the current value of I40E_PRTTSYN_STAT_1 and is
 * expected to be called only while under the ptp_rx_lock.
 **/
static u32 i40e_ptp_get_rx_events(struct i40e_pf *pf)
{
        struct i40e_hw *hw = &pf->hw;
        u32 prttsyn_stat, new_latch_events;
        int  i;

        prttsyn_stat = rd32(hw, I40E_PRTTSYN_STAT_1);
        new_latch_events = prttsyn_stat & ~pf->latch_event_flags;

        /* Update the jiffies time for any newly latched timestamp. This
         * ensures that we store the time that we first discovered a timestamp
         * was latched by the hardware. The service task will later determine
         * if we should free the latch and drop that timestamp should too much
         * time pass. This flow ensures that we only update jiffies for new
         * events latched since the last time we checked, and not all events
         * currently latched, so that the service task accounting remains
         * accurate.
         */
        for (i = 0; i < 4; i++) {
                if (new_latch_events & BIT(i))
                        pf->latch_events[i] = jiffies;
        }

        /* Finally, we store the current status of the Rx timestamp latches */
        pf->latch_event_flags = prttsyn_stat;

        return prttsyn_stat;
}

/**
 * i40e_ptp_rx_hang - Detect error case when Rx timestamp registers are hung
 * @pf: The PF private data structure
 *
 * This watchdog task is scheduled to detect error case where hardware has
 * dropped an Rx packet that was timestamped when the ring is full. The
 * particular error is rare but leaves the device in a state unable to timestamp
 * any future packets.
 **/
void i40e_ptp_rx_hang(struct i40e_pf *pf)
{
        struct i40e_hw *hw = &pf->hw;
        unsigned int i, cleared = 0;

        /* Since we cannot turn off the Rx timestamp logic if the device is
         * configured for Tx timestamping, we check if Rx timestamping is
         * configured. We don't want to spuriously warn about Rx timestamp
         * hangs if we don't care about the timestamps.
         */
        if (!test_bit(I40E_FLAG_PTP_ENA, pf->flags) || !pf->ptp_rx)
                return;

        spin_lock_bh(&pf->ptp_rx_lock);

        /* Update current latch times for Rx events */
        i40e_ptp_get_rx_events(pf);

        /* Check all the currently latched Rx events and see whether they have
         * been latched for over a second. It is assumed that any timestamp
         * should have been cleared within this time, or else it was captured
         * for a dropped frame that the driver never received. Thus, we will
         * clear any timestamp that has been latched for over 1 second.
         */
        for (i = 0; i < 4; i++) {
                if ((pf->latch_event_flags & BIT(i)) &&
                    time_is_before_jiffies(pf->latch_events[i] + HZ)) {
                        rd32(hw, I40E_PRTTSYN_RXTIME_H(i));
                        pf->latch_event_flags &= ~BIT(i);
                        cleared++;
                }
        }

        spin_unlock_bh(&pf->ptp_rx_lock);

        /* Log a warning if more than 2 timestamps got dropped in the same
         * check. We don't want to warn about all drops because it can occur
         * in normal scenarios such as PTP frames on multicast addresses we
         * aren't listening to. However, administrator should know if this is
         * the reason packets aren't receiving timestamps.
         */
        if (cleared > 2)
                dev_dbg(&pf->pdev->dev,
                        "Dropped %d missed RXTIME timestamp events\n",
                        cleared);

        /* Finally, update the rx_hwtstamp_cleared counter */
        pf->rx_hwtstamp_cleared += cleared;
}

/**
 * i40e_ptp_tx_hang - Detect error case when Tx timestamp register is hung
 * @pf: The PF private data structure
 *
 * This watchdog task is run periodically to make sure that we clear the Tx
 * timestamp logic if we don't obtain a timestamp in a reasonable amount of
 * time. It is unexpected in the normal case but if it occurs it results in
 * permanently preventing timestamps of future packets.
 **/
void i40e_ptp_tx_hang(struct i40e_pf *pf)
{
        struct sk_buff *skb;

        if (!test_bit(I40E_FLAG_PTP_ENA, pf->flags) || !pf->ptp_tx)
                return;

        /* Nothing to do if we're not already waiting for a timestamp */
        if (!test_bit(__I40E_PTP_TX_IN_PROGRESS, pf->state))
                return;

        /* We already have a handler routine which is run when we are notified
         * of a Tx timestamp in the hardware. If we don't get an interrupt
         * within a second it is reasonable to assume that we never will.
         */
        if (time_is_before_jiffies(pf->ptp_tx_start + HZ)) {
                skb = pf->ptp_tx_skb;
                pf->ptp_tx_skb = NULL;
                clear_bit_unlock(__I40E_PTP_TX_IN_PROGRESS, pf->state);

                /* Free the skb after we clear the bitlock */
                dev_kfree_skb_any(skb);
                pf->tx_hwtstamp_timeouts++;
        }
}

/**
 * i40e_ptp_tx_hwtstamp - Utility function which returns the Tx timestamp
 * @pf: Board private structure
 *
 * Read the value of the Tx timestamp from the registers, convert it into a
 * value consumable by the stack, and store that result into the shhwtstamps
 * struct before returning it up the stack.
 **/
void i40e_ptp_tx_hwtstamp(struct i40e_pf *pf)
{
        struct skb_shared_hwtstamps shhwtstamps;
        struct sk_buff *skb = pf->ptp_tx_skb;
        struct i40e_hw *hw = &pf->hw;
        u32 hi, lo;
        u64 ns;

        if (!test_bit(I40E_FLAG_PTP_ENA, pf->flags) || !pf->ptp_tx)
                return;

        /* don't attempt to timestamp if we don't have an skb */
        if (!pf->ptp_tx_skb)
                return;

        lo = rd32(hw, I40E_PRTTSYN_TXTIME_L);
        hi = rd32(hw, I40E_PRTTSYN_TXTIME_H);

        ns = (((u64)hi) << 32) | lo;
        i40e_ptp_convert_to_hwtstamp(&shhwtstamps, ns);

        /* Clear the bit lock as soon as possible after reading the register,
         * and prior to notifying the stack via skb_tstamp_tx(). Otherwise
         * applications might wake up and attempt to request another transmit
         * timestamp prior to the bit lock being cleared.
         */
        pf->ptp_tx_skb = NULL;
        clear_bit_unlock(__I40E_PTP_TX_IN_PROGRESS, pf->state);

        /* Notify the stack and free the skb after we've unlocked */
        skb_tstamp_tx(skb, &shhwtstamps);
        dev_kfree_skb_any(skb);
}

/**
 * i40e_ptp_rx_hwtstamp - Utility function which checks for an Rx timestamp
 * @pf: Board private structure
 * @skb: Particular skb to send timestamp with
 * @index: Index into the receive timestamp registers for the timestamp
 *
 * The XL710 receives a notification in the receive descriptor with an offset
 * into the set of RXTIME registers where the timestamp is for that skb. This
 * function goes and fetches the receive timestamp from that offset, if a valid
 * one exists. The RXTIME registers are in ns, so we must convert the result
 * first.
 **/
void i40e_ptp_rx_hwtstamp(struct i40e_pf *pf, struct sk_buff *skb, u8 index)
{
        u32 prttsyn_stat, hi, lo;
        struct i40e_hw *hw;
        u64 ns;

        /* Since we cannot turn off the Rx timestamp logic if the device is
         * doing Tx timestamping, check if Rx timestamping is configured.
         */
        if (!test_bit(I40E_FLAG_PTP_ENA, pf->flags) || !pf->ptp_rx)
                return;

        hw = &pf->hw;

        spin_lock_bh(&pf->ptp_rx_lock);

        /* Get current Rx events and update latch times */
        prttsyn_stat = i40e_ptp_get_rx_events(pf);

        /* TODO: Should we warn about missing Rx timestamp event? */
        if (!(prttsyn_stat & BIT(index))) {
                spin_unlock_bh(&pf->ptp_rx_lock);
                return;
        }

        /* Clear the latched event since we're about to read its register */
        pf->latch_event_flags &= ~BIT(index);

        lo = rd32(hw, I40E_PRTTSYN_RXTIME_L(index));
        hi = rd32(hw, I40E_PRTTSYN_RXTIME_H(index));

        spin_unlock_bh(&pf->ptp_rx_lock);

        ns = (((u64)hi) << 32) | lo;

        i40e_ptp_convert_to_hwtstamp(skb_hwtstamps(skb), ns);
}

/**
 * i40e_ptp_set_increment - Utility function to update clock increment rate
 * @pf: Board private structure
 *
 * During a link change, the DMA frequency that drives the 1588 logic will
 * change. In order to keep the PRTTSYN_TIME registers in units of nanoseconds,
 * we must update the increment value per clock tick.
 **/
void i40e_ptp_set_increment(struct i40e_pf *pf)
{
        struct i40e_link_status *hw_link_info;
        struct i40e_hw *hw = &pf->hw;
        u64 incval;
        u32 mult;

        hw_link_info = &hw->phy.link_info;

        i40e_aq_get_link_info(&pf->hw, true, NULL, NULL);

        switch (hw_link_info->link_speed) {
        case I40E_LINK_SPEED_10GB:
                mult = I40E_PTP_10GB_INCVAL_MULT;
                break;
        case I40E_LINK_SPEED_5GB:
                mult = I40E_PTP_5GB_INCVAL_MULT;
                break;
        case I40E_LINK_SPEED_1GB:
                mult = I40E_PTP_1GB_INCVAL_MULT;
                break;
        case I40E_LINK_SPEED_100MB:
        {
                static int warn_once;

                if (!warn_once) {
                        dev_warn(&pf->pdev->dev,
                                 "1588 functionality is not supported at 100 Mbps. Stopping the PHC.\n");
                        warn_once++;
                }
                mult = 0;
                break;
        }
        case I40E_LINK_SPEED_40GB:
        default:
                mult = 1;
                break;
        }

        /* The increment value is calculated by taking the base 40GbE incvalue
         * and multiplying it by a factor based on the link speed.
         */
        incval = I40E_PTP_40GB_INCVAL * mult;

        /* Write the new increment value into the increment register. The
         * hardware will not update the clock until both registers have been
         * written.
         */
        wr32(hw, I40E_PRTTSYN_INC_L, incval & 0xFFFFFFFF);
        wr32(hw, I40E_PRTTSYN_INC_H, incval >> 32);

        /* Update the base adjustement value. */
        WRITE_ONCE(pf->ptp_adj_mult, mult);
        smp_mb(); /* Force the above update. */
}

/**
 * i40e_ptp_hwtstamp_get - interface to read the HW timestamping
 * @netdev: Network device structure
 * @config: Timestamping configuration structure
 *
 * Obtain the current hardware timestamping settigs as requested. To do this,
 * keep a shadow copy of the timestamp settings rather than attempting to
 * deconstruct it from the registers.
 **/
int i40e_ptp_hwtstamp_get(struct net_device *netdev,
                          struct kernel_hwtstamp_config *config)
{
        struct i40e_netdev_priv *np = netdev_priv(netdev);
        struct i40e_pf *pf = np->vsi->back;

        if (!test_bit(I40E_FLAG_PTP_ENA, pf->flags))
                return -EOPNOTSUPP;

        *config = pf->tstamp_config;

        return 0;
}

/**
 * i40e_ptp_free_pins - free memory used by PTP pins
 * @pf: Board private structure
 *
 * Release memory allocated for PTP pins.
 **/
static void i40e_ptp_free_pins(struct i40e_pf *pf)
{
        if (i40e_is_ptp_pin_dev(&pf->hw)) {
                kfree(pf->ptp_pins);
                kfree(pf->ptp_caps.pin_config);
                pf->ptp_pins = NULL;
        }
}

/**
 * i40e_ptp_set_pin_hw - Set HW GPIO pin
 * @hw: pointer to the hardware structure
 * @pin: pin index
 * @state: pin state
 *
 * Set status of GPIO pin for external clock handling.
 **/
static void i40e_ptp_set_pin_hw(struct i40e_hw *hw,
                                unsigned int pin,
                                enum i40e_ptp_gpio_pin_state state)
{
        switch (state) {
        case off:
                wr32(hw, I40E_GLGEN_GPIO_CTL(pin), 0);
                break;
        case in_A:
                wr32(hw, I40E_GLGEN_GPIO_CTL(pin),
                     I40E_GLGEN_GPIO_CTL_PORT_0_IN_TIMESYNC_0);
                break;
        case in_B:
                wr32(hw, I40E_GLGEN_GPIO_CTL(pin),
                     I40E_GLGEN_GPIO_CTL_PORT_1_IN_TIMESYNC_0);
                break;
        case out_A:
                wr32(hw, I40E_GLGEN_GPIO_CTL(pin),
                     I40E_GLGEN_GPIO_CTL_PORT_0_OUT_TIMESYNC_1);
                break;
        case out_B:
                wr32(hw, I40E_GLGEN_GPIO_CTL(pin),
                     I40E_GLGEN_GPIO_CTL_PORT_1_OUT_TIMESYNC_1);
                break;
        default:
                break;
        }
}

/**
 * i40e_ptp_set_led_hw - Set HW GPIO led
 * @hw: pointer to the hardware structure
 * @led: led index
 * @state: led state
 *
 * Set status of GPIO led for external clock handling.
 **/
static void i40e_ptp_set_led_hw(struct i40e_hw *hw,
                                unsigned int led,
                                enum i40e_ptp_led_pin_state state)
{
        switch (state) {
        case low:
                wr32(hw, I40E_GLGEN_GPIO_SET,
                     I40E_GLGEN_GPIO_SET_DRV_SDP_DATA | led);
                break;
        case high:
                wr32(hw, I40E_GLGEN_GPIO_SET,
                     I40E_GLGEN_GPIO_SET_DRV_SDP_DATA |
                     I40E_GLGEN_GPIO_SET_SDP_DATA_HI | led);
                break;
        default:
                break;
        }
}

/**
 * i40e_ptp_init_leds_hw - init LEDs
 * @hw: pointer to a hardware structure
 *
 * Set initial state of LEDs
 **/
static void i40e_ptp_init_leds_hw(struct i40e_hw *hw)
{
        wr32(hw, I40E_GLGEN_GPIO_CTL(I40E_LED2_0),
             I40E_GLGEN_GPIO_CTL_LED_INIT);
        wr32(hw, I40E_GLGEN_GPIO_CTL(I40E_LED2_1),
             I40E_GLGEN_GPIO_CTL_LED_INIT);
        wr32(hw, I40E_GLGEN_GPIO_CTL(I40E_LED3_0),
             I40E_GLGEN_GPIO_CTL_LED_INIT);
        wr32(hw, I40E_GLGEN_GPIO_CTL(I40E_LED3_1),
             I40E_GLGEN_GPIO_CTL_LED_INIT);
}

/**
 * i40e_ptp_set_pins_hw - Set HW GPIO pins
 * @pf: Board private structure
 *
 * This function sets GPIO pins for PTP
 **/
static void i40e_ptp_set_pins_hw(struct i40e_pf *pf)
{
        const struct i40e_ptp_pins_settings *pins = pf->ptp_pins;
        struct i40e_hw *hw = &pf->hw;

        /* pin must be disabled before it may be used */
        i40e_ptp_set_pin_hw(hw, I40E_SDP3_2, off);
        i40e_ptp_set_pin_hw(hw, I40E_SDP3_3, off);
        i40e_ptp_set_pin_hw(hw, I40E_GPIO_4, off);

        i40e_ptp_set_pin_hw(hw, I40E_SDP3_2, pins->sdp3_2);
        i40e_ptp_set_pin_hw(hw, I40E_SDP3_3, pins->sdp3_3);
        i40e_ptp_set_pin_hw(hw, I40E_GPIO_4, pins->gpio_4);

        i40e_ptp_set_led_hw(hw, I40E_LED2_0, pins->led2_0);
        i40e_ptp_set_led_hw(hw, I40E_LED2_1, pins->led2_1);
        i40e_ptp_set_led_hw(hw, I40E_LED3_0, pins->led3_0);
        i40e_ptp_set_led_hw(hw, I40E_LED3_1, pins->led3_1);

        dev_info(&pf->pdev->dev,
                 "PTP configuration set to: SDP3_2: %s,  SDP3_3: %s,  GPIO_4: %s.\n",
                 i40e_ptp_gpio_pin_state2str[pins->sdp3_2],
                 i40e_ptp_gpio_pin_state2str[pins->sdp3_3],
                 i40e_ptp_gpio_pin_state2str[pins->gpio_4]);
}

/**
 * i40e_ptp_set_pins - set PTP pins in HW
 * @pf: Board private structure
 * @pins: PTP pins to be applied
 *
 * Validate and set PTP pins in HW for specific PF.
 * Return 0 on success or negative value on error.
 **/
static int i40e_ptp_set_pins(struct i40e_pf *pf,
                             struct i40e_ptp_pins_settings *pins)
{
        enum i40e_can_set_pins pin_caps = i40e_can_set_pins(pf);
        int i = 0;

        if (pin_caps == CANT_DO_PINS)
                return -EOPNOTSUPP;
        else if (pin_caps == CAN_DO_PINS)
                return 0;

        if (pins->sdp3_2 == invalid)
                pins->sdp3_2 = pf->ptp_pins->sdp3_2;
        if (pins->sdp3_3 == invalid)
                pins->sdp3_3 = pf->ptp_pins->sdp3_3;
        if (pins->gpio_4 == invalid)
                pins->gpio_4 = pf->ptp_pins->gpio_4;
        while (i40e_ptp_pin_led_allowed_states[i].sdp3_2 != end) {
                if (pins->sdp3_2 == i40e_ptp_pin_led_allowed_states[i].sdp3_2 &&
                    pins->sdp3_3 == i40e_ptp_pin_led_allowed_states[i].sdp3_3 &&
                    pins->gpio_4 == i40e_ptp_pin_led_allowed_states[i].gpio_4) {
                        pins->led2_0 =
                                i40e_ptp_pin_led_allowed_states[i].led2_0;
                        pins->led2_1 =
                                i40e_ptp_pin_led_allowed_states[i].led2_1;
                        pins->led3_0 =
                                i40e_ptp_pin_led_allowed_states[i].led3_0;
                        pins->led3_1 =
                                i40e_ptp_pin_led_allowed_states[i].led3_1;
                        break;
                }
                i++;
        }
        if (i40e_ptp_pin_led_allowed_states[i].sdp3_2 == end) {
                dev_warn(&pf->pdev->dev,
                         "Unsupported PTP pin configuration: SDP3_2: %s,  SDP3_3: %s,  GPIO_4: %s.\n",
                         i40e_ptp_gpio_pin_state2str[pins->sdp3_2],
                         i40e_ptp_gpio_pin_state2str[pins->sdp3_3],
                         i40e_ptp_gpio_pin_state2str[pins->gpio_4]);

                return -EPERM;
        }
        memcpy(pf->ptp_pins, pins, sizeof(*pins));
        i40e_ptp_set_pins_hw(pf);
        i40_ptp_reset_timing_events(pf);

        return 0;
}

/**
 * i40e_ptp_alloc_pins - allocate PTP pins structure
 * @pf: Board private structure
 *
 * allocate PTP pins structure
 **/
int i40e_ptp_alloc_pins(struct i40e_pf *pf)
{
        if (!i40e_is_ptp_pin_dev(&pf->hw))
                return 0;

        pf->ptp_pins =
                kzalloc_obj(struct i40e_ptp_pins_settings);

        if (!pf->ptp_pins) {
                dev_warn(&pf->pdev->dev, "Cannot allocate memory for PTP pins structure.\n");
                return -ENOMEM;
        }

        pf->ptp_pins->sdp3_2 = off;
        pf->ptp_pins->sdp3_3 = off;
        pf->ptp_pins->gpio_4 = off;
        pf->ptp_pins->led2_0 = high;
        pf->ptp_pins->led2_1 = high;
        pf->ptp_pins->led3_0 = high;
        pf->ptp_pins->led3_1 = high;

        /* Use PF0 to set pins in HW. Return success for user space tools */
        if (pf->hw.pf_id)
                return 0;

        i40e_ptp_init_leds_hw(&pf->hw);
        i40e_ptp_set_pins_hw(pf);

        return 0;
}

/**
 * i40e_ptp_set_timestamp_mode - setup hardware for requested timestamp mode
 * @pf: Board private structure
 * @config: hwtstamp settings requested or saved
 *
 * Control hardware registers to enter the specific mode requested by the
 * user. Also used during reset path to ensure that timestamp settings are
 * maintained.
 *
 * Note: modifies config in place, and may update the requested mode to be
 * more broad if the specific filter is not directly supported.
 **/
static int i40e_ptp_set_timestamp_mode(struct i40e_pf *pf,
                                       struct kernel_hwtstamp_config *config)
{
        struct i40e_hw *hw = &pf->hw;
        u32 tsyntype, regval;

        /* Selects external trigger to cause event */
        regval = rd32(hw, I40E_PRTTSYN_AUX_0(0));
        /* Bit 17:16 is EVNTLVL, 01B rising edge */
        regval &= 0;
        regval |= (1 << I40E_PRTTSYN_AUX_0_EVNTLVL_SHIFT);
        /* regval: 0001 0000 0000 0000 0000 */
        wr32(hw, I40E_PRTTSYN_AUX_0(0), regval);

        /* Enabel interrupts */
        regval = rd32(hw, I40E_PRTTSYN_CTL0);
        regval |= 1 << I40E_PRTTSYN_CTL0_EVENT_INT_ENA_SHIFT;
        wr32(hw, I40E_PRTTSYN_CTL0, regval);

        INIT_WORK(&pf->ptp_extts0_work, i40e_ptp_extts0_work);

        switch (config->tx_type) {
        case HWTSTAMP_TX_OFF:
                pf->ptp_tx = false;
                break;
        case HWTSTAMP_TX_ON:
                pf->ptp_tx = true;
                break;
        default:
                return -ERANGE;
        }

        switch (config->rx_filter) {
        case HWTSTAMP_FILTER_NONE:
                pf->ptp_rx = false;
                /* We set the type to V1, but do not enable UDP packet
                 * recognition. In this way, we should be as close to
                 * disabling PTP Rx timestamps as possible since V1 packets
                 * are always UDP, since L2 packets are a V2 feature.
                 */
                tsyntype = I40E_PRTTSYN_CTL1_TSYNTYPE_V1;
                break;
        case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
        case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
        case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
                if (!test_bit(I40E_HW_CAP_PTP_L4, pf->hw.caps))
                        return -ERANGE;
                pf->ptp_rx = true;
                tsyntype = I40E_PRTTSYN_CTL1_V1MESSTYPE0_MASK |
                           I40E_PRTTSYN_CTL1_TSYNTYPE_V1 |
                           I40E_PRTTSYN_CTL1_UDP_ENA_MASK;
                config->rx_filter = HWTSTAMP_FILTER_PTP_V1_L4_EVENT;
                break;
        case HWTSTAMP_FILTER_PTP_V2_EVENT:
        case HWTSTAMP_FILTER_PTP_V2_L4_EVENT:
        case HWTSTAMP_FILTER_PTP_V2_SYNC:
        case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:
        case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ:
        case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ:
                if (!test_bit(I40E_HW_CAP_PTP_L4, pf->hw.caps))
                        return -ERANGE;
                fallthrough;
        case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
        case HWTSTAMP_FILTER_PTP_V2_L2_SYNC:
        case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ:
                pf->ptp_rx = true;
                tsyntype = I40E_PRTTSYN_CTL1_V2MESSTYPE0_MASK |
                           I40E_PRTTSYN_CTL1_TSYNTYPE_V2;
                if (test_bit(I40E_HW_CAP_PTP_L4, pf->hw.caps)) {
                        tsyntype |= I40E_PRTTSYN_CTL1_UDP_ENA_MASK;
                        config->rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
                } else {
                        config->rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
                }
                break;
        case HWTSTAMP_FILTER_NTP_ALL:
        case HWTSTAMP_FILTER_ALL:
        default:
                return -ERANGE;
        }

        /* Clear out all 1588-related registers to clear and unlatch them. */
        spin_lock_bh(&pf->ptp_rx_lock);
        rd32(hw, I40E_PRTTSYN_STAT_0);
        rd32(hw, I40E_PRTTSYN_TXTIME_H);
        rd32(hw, I40E_PRTTSYN_RXTIME_H(0));
        rd32(hw, I40E_PRTTSYN_RXTIME_H(1));
        rd32(hw, I40E_PRTTSYN_RXTIME_H(2));
        rd32(hw, I40E_PRTTSYN_RXTIME_H(3));
        pf->latch_event_flags = 0;
        spin_unlock_bh(&pf->ptp_rx_lock);

        /* Enable/disable the Tx timestamp interrupt based on user input. */
        regval = rd32(hw, I40E_PRTTSYN_CTL0);
        if (pf->ptp_tx)
                regval |= I40E_PRTTSYN_CTL0_TXTIME_INT_ENA_MASK;
        else
                regval &= ~I40E_PRTTSYN_CTL0_TXTIME_INT_ENA_MASK;
        wr32(hw, I40E_PRTTSYN_CTL0, regval);

        regval = rd32(hw, I40E_PFINT_ICR0_ENA);
        if (pf->ptp_tx)
                regval |= I40E_PFINT_ICR0_ENA_TIMESYNC_MASK;
        else
                regval &= ~I40E_PFINT_ICR0_ENA_TIMESYNC_MASK;
        wr32(hw, I40E_PFINT_ICR0_ENA, regval);

        /* Although there is no simple on/off switch for Rx, we "disable" Rx
         * timestamps by setting to V1 only mode and clear the UDP
         * recognition. This ought to disable all PTP Rx timestamps as V1
         * packets are always over UDP. Note that software is configured to
         * ignore Rx timestamps via the pf->ptp_rx flag.
         */
        regval = rd32(hw, I40E_PRTTSYN_CTL1);
        /* clear everything but the enable bit */
        regval &= I40E_PRTTSYN_CTL1_TSYNENA_MASK;
        /* now enable bits for desired Rx timestamps */
        regval |= tsyntype;
        wr32(hw, I40E_PRTTSYN_CTL1, regval);

        return 0;
}

/**
 * i40e_ptp_hwtstamp_set - interface to control the HW timestamping
 * @netdev: Network device structure
 * @config: Timestamping configuration structure
 * @extack: Netlink extended ack structure for error reporting
 *
 * Respond to the user filter requests and make the appropriate hardware
 * changes here. The XL710 cannot support splitting of the Tx/Rx timestamping
 * logic, so keep track in software of whether to indicate these timestamps
 * or not.
 *
 * It is permissible to "upgrade" the user request to a broader filter, as long
 * as the user receives the timestamps they care about and the user is notified
 * the filter has been broadened.
 **/
int i40e_ptp_hwtstamp_set(struct net_device *netdev,
                          struct kernel_hwtstamp_config *config,
                          struct netlink_ext_ack *extack)
{
        struct i40e_netdev_priv *np = netdev_priv(netdev);
        struct i40e_pf *pf = np->vsi->back;
        int err;

        if (!test_bit(I40E_FLAG_PTP_ENA, pf->flags))
                return -EOPNOTSUPP;

        err = i40e_ptp_set_timestamp_mode(pf, config);
        if (err)
                return err;

        /* save these settings for future reference */
        pf->tstamp_config = *config;

        return 0;
}

/**
 * i40e_init_pin_config - initialize pins.
 * @pf: private board structure
 *
 * Initialize pins for external clock source.
 * Return 0 on success or error code on failure.
 **/
static int i40e_init_pin_config(struct i40e_pf *pf)
{
        int i;

        pf->ptp_caps.n_pins = 3;
        pf->ptp_caps.n_ext_ts = 2;
        pf->ptp_caps.pps = 1;
        pf->ptp_caps.n_per_out = 2;

        pf->ptp_caps.pin_config = kzalloc_objs(*pf->ptp_caps.pin_config,
                                               pf->ptp_caps.n_pins);
        if (!pf->ptp_caps.pin_config)
                return -ENOMEM;

        for (i = 0; i < pf->ptp_caps.n_pins; i++) {
                snprintf(pf->ptp_caps.pin_config[i].name,
                         sizeof(pf->ptp_caps.pin_config[i].name),
                         "%s", sdp_desc[i].name);
                pf->ptp_caps.pin_config[i].index = sdp_desc[i].index;
                pf->ptp_caps.pin_config[i].func = PTP_PF_NONE;
                pf->ptp_caps.pin_config[i].chan = sdp_desc[i].chan;
        }

        pf->ptp_caps.verify = i40e_ptp_verify;
        pf->ptp_caps.enable = i40e_ptp_feature_enable;

        pf->ptp_caps.pps = 1;

        return 0;
}

/**
 * i40e_ptp_create_clock - Create PTP clock device for userspace
 * @pf: Board private structure
 *
 * This function creates a new PTP clock device. It only creates one if we
 * don't already have one, so it is safe to call. Will return error if it
 * can't create one, but success if we already have a device. Should be used
 * by i40e_ptp_init to create clock initially, and prevent global resets from
 * creating new clock devices.
 **/
static long i40e_ptp_create_clock(struct i40e_pf *pf)
{
        /* no need to create a clock device if we already have one */
        if (!IS_ERR_OR_NULL(pf->ptp_clock))
                return 0;

        strscpy(pf->ptp_caps.name, i40e_driver_name,
                sizeof(pf->ptp_caps.name) - 1);
        pf->ptp_caps.owner = THIS_MODULE;
        pf->ptp_caps.max_adj = 999999999;
        pf->ptp_caps.adjfine = i40e_ptp_adjfine;
        pf->ptp_caps.adjtime = i40e_ptp_adjtime;
        pf->ptp_caps.gettimex64 = i40e_ptp_gettimex;
        pf->ptp_caps.settime64 = i40e_ptp_settime;
        if (i40e_is_ptp_pin_dev(&pf->hw)) {
                int err = i40e_init_pin_config(pf);

                if (err)
                        return err;
        }

        /* Attempt to register the clock before enabling the hardware. */
        pf->ptp_clock = ptp_clock_register(&pf->ptp_caps, &pf->pdev->dev);
        if (IS_ERR(pf->ptp_clock))
                return PTR_ERR(pf->ptp_clock);

        /* clear the hwtstamp settings here during clock create, instead of
         * during regular init, so that we can maintain settings across a
         * reset or suspend.
         */
        pf->tstamp_config.rx_filter = HWTSTAMP_FILTER_NONE;
        pf->tstamp_config.tx_type = HWTSTAMP_TX_OFF;

        /* Set the previous "reset" time to the current Kernel clock time */
        ktime_get_real_ts64(&pf->ptp_prev_hw_time);
        pf->ptp_reset_start = ktime_get();

        return 0;
}

/**
 * i40e_ptp_save_hw_time - Save the current PTP time as ptp_prev_hw_time
 * @pf: Board private structure
 *
 * Read the current PTP time and save it into pf->ptp_prev_hw_time. This should
 * be called at the end of preparing to reset, just before hardware reset
 * occurs, in order to preserve the PTP time as close as possible across
 * resets.
 */
void i40e_ptp_save_hw_time(struct i40e_pf *pf)
{
        /* don't try to access the PTP clock if it's not enabled */
        if (!test_bit(I40E_FLAG_PTP_ENA, pf->flags))
                return;

        i40e_ptp_gettimex(&pf->ptp_caps, &pf->ptp_prev_hw_time, NULL);
        /* Get a monotonic starting time for this reset */
        pf->ptp_reset_start = ktime_get();
}

/**
 * i40e_ptp_restore_hw_time - Restore the ptp_prev_hw_time + delta to PTP regs
 * @pf: Board private structure
 *
 * Restore the PTP hardware clock registers. We previously cached the PTP
 * hardware time as pf->ptp_prev_hw_time. To be as accurate as possible,
 * update this value based on the time delta since the time was saved, using
 * CLOCK_MONOTONIC (via ktime_get()) to calculate the time difference.
 *
 * This ensures that the hardware clock is restored to nearly what it should
 * have been if a reset had not occurred.
 */
void i40e_ptp_restore_hw_time(struct i40e_pf *pf)
{
        ktime_t delta = ktime_sub(ktime_get(), pf->ptp_reset_start);

        /* Update the previous HW time with the ktime delta */
        timespec64_add_ns(&pf->ptp_prev_hw_time, ktime_to_ns(delta));

        /* Restore the hardware clock registers */
        i40e_ptp_settime(&pf->ptp_caps, &pf->ptp_prev_hw_time);
}

/**
 * i40e_ptp_init - Initialize the 1588 support after device probe or reset
 * @pf: Board private structure
 *
 * This function sets device up for 1588 support. The first time it is run, it
 * will create a PHC clock device. It does not create a clock device if one
 * already exists. It also reconfigures the device after a reset.
 *
 * The first time a clock is created, i40e_ptp_create_clock will set
 * pf->ptp_prev_hw_time to the current system time. During resets, it is
 * expected that this timespec will be set to the last known PTP clock time,
 * in order to preserve the clock time as close as possible across a reset.
 **/
void i40e_ptp_init(struct i40e_pf *pf)
{
        struct i40e_vsi *vsi = i40e_pf_get_main_vsi(pf);
        struct net_device *netdev = vsi->netdev;
        struct i40e_hw *hw = &pf->hw;
        u32 pf_id;
        long err;

        /* Only one PF is assigned to control 1588 logic per port. Do not
         * enable any support for PFs not assigned via PRTTSYN_CTL0.PF_ID
         */
        pf_id = FIELD_GET(I40E_PRTTSYN_CTL0_PF_ID_MASK,
                          rd32(hw, I40E_PRTTSYN_CTL0));
        if (hw->pf_id != pf_id) {
                clear_bit(I40E_FLAG_PTP_ENA, pf->flags);
                dev_info(&pf->pdev->dev, "%s: PTP not supported on %s\n",
                         __func__,
                         netdev->name);
                return;
        }

        mutex_init(&pf->tmreg_lock);
        spin_lock_init(&pf->ptp_rx_lock);

        /* ensure we have a clock device */
        err = i40e_ptp_create_clock(pf);
        if (err) {
                pf->ptp_clock = NULL;
                dev_err(&pf->pdev->dev, "%s: ptp_clock_register failed\n",
                        __func__);
        } else if (pf->ptp_clock) {
                u32 regval;

                if (pf->hw.debug_mask & I40E_DEBUG_LAN)
                        dev_info(&pf->pdev->dev, "PHC enabled\n");
                set_bit(I40E_FLAG_PTP_ENA, pf->flags);

                /* Ensure the clocks are running. */
                regval = rd32(hw, I40E_PRTTSYN_CTL0);
                regval |= I40E_PRTTSYN_CTL0_TSYNENA_MASK;
                wr32(hw, I40E_PRTTSYN_CTL0, regval);
                regval = rd32(hw, I40E_PRTTSYN_CTL1);
                regval |= I40E_PRTTSYN_CTL1_TSYNENA_MASK;
                wr32(hw, I40E_PRTTSYN_CTL1, regval);

                /* Set the increment value per clock tick. */
                i40e_ptp_set_increment(pf);

                /* reset timestamping mode */
                i40e_ptp_set_timestamp_mode(pf, &pf->tstamp_config);

                /* Restore the clock time based on last known value */
                i40e_ptp_restore_hw_time(pf);
        }

        i40e_ptp_set_1pps_signal_hw(pf);
}

/**
 * i40e_ptp_stop - Disable the driver/hardware support and unregister the PHC
 * @pf: Board private structure
 *
 * This function handles the cleanup work required from the initialization by
 * clearing out the important information and unregistering the PHC.
 **/
void i40e_ptp_stop(struct i40e_pf *pf)
{
        struct i40e_vsi *main_vsi = i40e_pf_get_main_vsi(pf);
        struct i40e_hw *hw = &pf->hw;
        u32 regval;

        clear_bit(I40E_FLAG_PTP_ENA, pf->flags);
        pf->ptp_tx = false;
        pf->ptp_rx = false;

        if (pf->ptp_tx_skb) {
                struct sk_buff *skb = pf->ptp_tx_skb;

                pf->ptp_tx_skb = NULL;
                clear_bit_unlock(__I40E_PTP_TX_IN_PROGRESS, pf->state);
                dev_kfree_skb_any(skb);
        }

        if (pf->ptp_clock) {
                ptp_clock_unregister(pf->ptp_clock);
                pf->ptp_clock = NULL;
                dev_info(&pf->pdev->dev, "%s: removed PHC on %s\n", __func__,
                         main_vsi->netdev->name);
        }

        if (i40e_is_ptp_pin_dev(&pf->hw)) {
                i40e_ptp_set_pin_hw(hw, I40E_SDP3_2, off);
                i40e_ptp_set_pin_hw(hw, I40E_SDP3_3, off);
                i40e_ptp_set_pin_hw(hw, I40E_GPIO_4, off);
        }

        regval = rd32(hw, I40E_PRTTSYN_AUX_0(0));
        regval &= ~I40E_PRTTSYN_AUX_0_PTPFLAG_MASK;
        wr32(hw, I40E_PRTTSYN_AUX_0(0), regval);

        /* Disable interrupts */
        regval = rd32(hw, I40E_PRTTSYN_CTL0);
        regval &= ~I40E_PRTTSYN_CTL0_EVENT_INT_ENA_MASK;
        wr32(hw, I40E_PRTTSYN_CTL0, regval);

        i40e_ptp_free_pins(pf);
}