// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * wm9705.c  --  Codec driver for Wolfson WM9705 AC97 Codec.
 *
 * Copyright 2003, 2004, 2005, 2006, 2007 Wolfson Microelectronics PLC.
 * Author: Liam Girdwood <lrg@slimlogic.co.uk>
 * Parts Copyright : Ian Molton <spyro@f2s.com>
 *                   Andrew Zabolotny <zap@homelink.ru>
 *                   Russell King <rmk@arm.linux.org.uk>
 */

#include <linux/export.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/kernel.h>
#include <linux/input.h>
#include <linux/delay.h>
#include <linux/bitops.h>
#include <linux/wm97xx.h>

#define TS_NAME                 "wm97xx"
#define WM9705_VERSION          "1.00"
#define DEFAULT_PRESSURE        0xb0c0

/*
 * Module parameters
 */

/*
 * Set current used for pressure measurement.
 *
 * Set pil = 2 to use 400uA
 *     pil = 1 to use 200uA and
 *     pil = 0 to disable pressure measurement.
 *
 * This is used to increase the range of values returned by the adc
 * when measureing touchpanel pressure.
 */
static int pil;
module_param(pil, int, 0);
MODULE_PARM_DESC(pil, "Set current used for pressure measurement.");

/*
 * Set threshold for pressure measurement.
 *
 * Pen down pressure below threshold is ignored.
 */
static int pressure = DEFAULT_PRESSURE & 0xfff;
module_param(pressure, int, 0);
MODULE_PARM_DESC(pressure, "Set threshold for pressure measurement.");

/*
 * Set adc sample delay.
 *
 * For accurate touchpanel measurements, some settling time may be
 * required between the switch matrix applying a voltage across the
 * touchpanel plate and the ADC sampling the signal.
 *
 * This delay can be set by setting delay = n, where n is the array
 * position of the delay in the array delay_table below.
 * Long delays > 1ms are supported for completeness, but are not
 * recommended.
 */
static int delay = 4;
module_param(delay, int, 0);
MODULE_PARM_DESC(delay, "Set adc sample delay.");

/*
 * Pen detect comparator threshold.
 *
 * 0 to Vmid in 15 steps, 0 = use zero power comparator with Vmid threshold
 * i.e. 1 =  Vmid/15 threshold
 *      15 =  Vmid/1 threshold
 *
 * Adjust this value if you are having problems with pen detect not
 * detecting any down events.
 */
static int pdd = 8;
module_param(pdd, int, 0);
MODULE_PARM_DESC(pdd, "Set pen detect comparator threshold");

/*
 * Set adc mask function.
 *
 * Sources of glitch noise, such as signals driving an LCD display, may feed
 * through to the touch screen plates and affect measurement accuracy. In
 * order to minimise this, a signal may be applied to the MASK pin to delay or
 * synchronise the sampling.
 *
 * 0 = No delay or sync
 * 1 = High on pin stops conversions
 * 2 = Edge triggered, edge on pin delays conversion by delay param (above)
 * 3 = Edge triggered, edge on pin starts conversion after delay param
 */
static int mask;
module_param(mask, int, 0);
MODULE_PARM_DESC(mask, "Set adc mask function.");

/*
 * ADC sample delay times in uS
 */
static const int delay_table[] = {
        21,    /* 1 AC97 Link frames */
        42,    /* 2                  */
        84,    /* 4                  */
        167,   /* 8                  */
        333,   /* 16                 */
        667,   /* 32                 */
        1000,  /* 48                 */
        1333,  /* 64                 */
        2000,  /* 96                 */
        2667,  /* 128                */
        3333,  /* 160                */
        4000,  /* 192                */
        4667,  /* 224                */
        5333,  /* 256                */
        6000,  /* 288                */
        0      /* No delay, switch matrix always on */
};

/*
 * Delay after issuing a POLL command.
 *
 * The delay is 3 AC97 link frames + the touchpanel settling delay
 */
static inline void poll_delay(int d)
{
        udelay(3 * AC97_LINK_FRAME + delay_table[d]);
}

/*
 * set up the physical settings of the WM9705
 */
static void wm9705_phy_init(struct wm97xx *wm)
{
        u16 dig1 = 0, dig2 = WM97XX_RPR;

        /*
        * mute VIDEO and AUX as they share X and Y touchscreen
        * inputs on the WM9705
        */
        wm97xx_reg_write(wm, AC97_AUX, 0x8000);
        wm97xx_reg_write(wm, AC97_VIDEO, 0x8000);

        /* touchpanel pressure current*/
        if (pil == 2) {
                dig2 |= WM9705_PIL;
                dev_dbg(wm->dev,
                        "setting pressure measurement current to 400uA.");
        } else if (pil)
                dev_dbg(wm->dev,
                        "setting pressure measurement current to 200uA.");
        if (!pil)
                pressure = 0;

        /* polling mode sample settling delay */
        if (delay != 4) {
                if (delay < 0 || delay > 15) {
                        dev_dbg(wm->dev, "supplied delay out of range.");
                        delay = 4;
                }
        }
        dig1 &= 0xff0f;
        dig1 |= WM97XX_DELAY(delay);
        dev_dbg(wm->dev, "setting adc sample delay to %d u Secs.",
                delay_table[delay]);

        /* WM9705 pdd */
        dig2 |= (pdd & 0x000f);
        dev_dbg(wm->dev, "setting pdd to Vmid/%d", 1 - (pdd & 0x000f));

        /* mask */
        dig2 |= ((mask & 0x3) << 4);

        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
}

static void wm9705_dig_enable(struct wm97xx *wm, int enable)
{
        if (enable) {
                wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
                                 wm->dig[2] | WM97XX_PRP_DET_DIG);
                wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); /* dummy read */
        } else
                wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
                                 wm->dig[2] & ~WM97XX_PRP_DET_DIG);
}

static void wm9705_aux_prepare(struct wm97xx *wm)
{
        memcpy(wm->dig_save, wm->dig, sizeof(wm->dig));
        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, 0);
        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, WM97XX_PRP_DET_DIG);
}

static void wm9705_dig_restore(struct wm97xx *wm)
{
        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, wm->dig_save[1]);
        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, wm->dig_save[2]);
}

static inline int is_pden(struct wm97xx *wm)
{
        return wm->dig[2] & WM9705_PDEN;
}

/*
 * Read a sample from the WM9705 adc in polling mode.
 */
static int wm9705_poll_sample(struct wm97xx *wm, int adcsel, int *sample)
{
        int timeout = 5 * delay;
        bool wants_pen = adcsel & WM97XX_PEN_DOWN;

        if (wants_pen && !wm->pen_probably_down) {
                u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
                if (!(data & WM97XX_PEN_DOWN))
                        return RC_PENUP;
                wm->pen_probably_down = 1;
        }

        /* set up digitiser */
        if (wm->mach_ops && wm->mach_ops->pre_sample)
                wm->mach_ops->pre_sample(adcsel);
        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, (adcsel & WM97XX_ADCSEL_MASK)
                                | WM97XX_POLL | WM97XX_DELAY(delay));

        /* wait 3 AC97 time slots + delay for conversion */
        poll_delay(delay);

        /* wait for POLL to go low */
        while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
               && timeout) {
                udelay(AC97_LINK_FRAME);
                timeout--;
        }

        if (timeout == 0) {
                /* If PDEN is set, we can get a timeout when pen goes up */
                if (is_pden(wm))
                        wm->pen_probably_down = 0;
                else
                        dev_dbg(wm->dev, "adc sample timeout");
                return RC_PENUP;
        }

        *sample = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
        if (wm->mach_ops && wm->mach_ops->post_sample)
                wm->mach_ops->post_sample(adcsel);

        /* check we have correct sample */
        if ((*sample ^ adcsel) & WM97XX_ADCSEL_MASK) {
                dev_dbg(wm->dev, "adc wrong sample, wanted %x got %x",
                        adcsel & WM97XX_ADCSEL_MASK,
                        *sample & WM97XX_ADCSEL_MASK);
                return RC_PENUP;
        }

        if (wants_pen && !(*sample & WM97XX_PEN_DOWN)) {
                wm->pen_probably_down = 0;
                return RC_PENUP;
        }

        return RC_VALID;
}

/*
 * Sample the WM9705 touchscreen in polling mode
 */
static int wm9705_poll_touch(struct wm97xx *wm, struct wm97xx_data *data)
{
        int rc;

        rc = wm9705_poll_sample(wm, WM97XX_ADCSEL_X | WM97XX_PEN_DOWN, &data->x);
        if (rc != RC_VALID)
                return rc;
        rc = wm9705_poll_sample(wm, WM97XX_ADCSEL_Y | WM97XX_PEN_DOWN, &data->y);
        if (rc != RC_VALID)
                return rc;
        if (pil) {
                rc = wm9705_poll_sample(wm, WM97XX_ADCSEL_PRES | WM97XX_PEN_DOWN, &data->p);
                if (rc != RC_VALID)
                        return rc;
        } else
                data->p = DEFAULT_PRESSURE;

        return RC_VALID;
}

/*
 * Enable WM9705 continuous mode, i.e. touch data is streamed across
 * an AC97 slot
 */
static int wm9705_acc_enable(struct wm97xx *wm, int enable)
{
        u16 dig1, dig2;
        int ret = 0;

        dig1 = wm->dig[1];
        dig2 = wm->dig[2];

        if (enable) {
                /* continuous mode */
                if (wm->mach_ops->acc_startup &&
                    (ret = wm->mach_ops->acc_startup(wm)) < 0)
                        return ret;
                dig1 &= ~(WM97XX_CM_RATE_MASK | WM97XX_ADCSEL_MASK |
                          WM97XX_DELAY_MASK | WM97XX_SLT_MASK);
                dig1 |= WM97XX_CTC | WM97XX_COO | WM97XX_SLEN |
                        WM97XX_DELAY(delay) |
                        WM97XX_SLT(wm->acc_slot) |
                        WM97XX_RATE(wm->acc_rate);
                if (pil)
                        dig1 |= WM97XX_ADCSEL_PRES;
                dig2 |= WM9705_PDEN;
        } else {
                dig1 &= ~(WM97XX_CTC | WM97XX_COO | WM97XX_SLEN);
                dig2 &= ~WM9705_PDEN;
                if (wm->mach_ops->acc_shutdown)
                        wm->mach_ops->acc_shutdown(wm);
        }

        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);

        return ret;
}

struct wm97xx_codec_drv wm9705_codec = {
        .id = WM9705_ID2,
        .name = "wm9705",
        .poll_sample = wm9705_poll_sample,
        .poll_touch = wm9705_poll_touch,
        .acc_enable = wm9705_acc_enable,
        .phy_init = wm9705_phy_init,
        .dig_enable = wm9705_dig_enable,
        .dig_restore = wm9705_dig_restore,
        .aux_prepare = wm9705_aux_prepare,
};
EXPORT_SYMBOL_GPL(wm9705_codec);

/* Module information */
MODULE_AUTHOR("Liam Girdwood <lrg@slimlogic.co.uk>");
MODULE_DESCRIPTION("WM9705 Touch Screen Driver");
MODULE_LICENSE("GPL");