include/linux/alcor_pci.h

root/include/linux/alcor_pci.h
/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright (C) 2018 Oleksij Rempel <linux@rempel-privat.de>
 *
 * Driver for Alcor Micro AU6601 and AU6621 controllers
 */

#ifndef __ALCOR_PCI_H
#define __ALCOR_PCI_H

#define ALCOR_SD_CARD 0
#define ALCOR_MS_CARD 1

#define DRV_NAME_ALCOR_PCI                      "alcor_pci"
#define DRV_NAME_ALCOR_PCI_SDMMC                "alcor_sdmmc"
#define DRV_NAME_ALCOR_PCI_MS                   "alcor_ms"

#define PCI_ID_ALCOR_MICRO                      0x1AEA
#define PCI_ID_AU6601                           0x6601
#define PCI_ID_AU6621                           0x6621
#define PCI_ID_AU6625                           0x6625

#define MHZ_TO_HZ(freq)                         ((freq) * 1000 * 1000)

#define AU6601_BASE_CLOCK                       31000000
#define AU6601_MIN_CLOCK                        150000
#define AU6601_MAX_CLOCK                        208000000
#define AU6601_MAX_DMA_SEGMENTS                 64
#define AU6601_MAX_PIO_SEGMENTS                 1
#define AU6601_MAX_DMA_BLOCK_SIZE               0x1000
#define AU6601_MAX_PIO_BLOCK_SIZE               0x200
#define AU6601_MAX_DMA_BLOCKS                   1
#define AU6601_DMA_LOCAL_SEGMENTS               1

/* registers spotter by reverse engineering but still
 * with unknown functionality:
 * 0x10 - ADMA phy address. AU6621 only?
 * 0x51 - LED ctrl?
 * 0x52 - unknown
 * 0x61 - LED related? Always toggled BIT0
 * 0x63 - Same as 0x61?
 * 0x77 - unknown
 */

/* SDMA phy address. Higher then 0x0800.0000?
 * The au6601 and au6621 have different DMA engines with different issues. One
 * For example au6621 engine is triggered by addr change. No other interaction
 * is needed. This means, if we get two buffers with same address, then engine
 * will stall.
 */
#define AU6601_REG_SDMA_ADDR                    0x00
#define AU6601_SDMA_MASK                        0xffffffff

#define AU6601_DMA_BOUNDARY                     0x05
#define AU6621_DMA_PAGE_CNT                     0x05
/* PIO */
#define AU6601_REG_BUFFER                       0x08
/* ADMA ctrl? AU6621 only. */
#define AU6621_DMA_CTRL                         0x0c
#define AU6621_DMA_ENABLE                       BIT(0)
/* CMD index */
#define AU6601_REG_CMD_OPCODE                   0x23
/* CMD parametr */
#define AU6601_REG_CMD_ARG                      0x24
/* CMD response 4x4 Bytes */
#define AU6601_REG_CMD_RSP0                     0x30
#define AU6601_REG_CMD_RSP1                     0x34
#define AU6601_REG_CMD_RSP2                     0x38
#define AU6601_REG_CMD_RSP3                     0x3C
/* default timeout set to 125: 125 * 40ms = 5 sec
 * how exactly it is calculated?
 */
#define AU6601_TIME_OUT_CTRL                    0x69
/* Block size for SDMA or PIO */
#define AU6601_REG_BLOCK_SIZE                   0x6c
/* Some power related reg, used together with AU6601_OUTPUT_ENABLE */
#define AU6601_POWER_CONTROL                    0x70

/* PLL ctrl */
#define AU6601_CLK_SELECT                       0x72
#define AU6601_CLK_OVER_CLK                     0x80
#define AU6601_CLK_384_MHZ                      0x30
#define AU6601_CLK_125_MHZ                      0x20
#define AU6601_CLK_48_MHZ                       0x10
#define AU6601_CLK_EXT_PLL                      0x04
#define AU6601_CLK_X2_MODE                      0x02
#define AU6601_CLK_ENABLE                       0x01
#define AU6601_CLK_31_25_MHZ                    0x00

#define AU6601_CLK_DIVIDER                      0x73

#define AU6601_INTERFACE_MODE_CTRL              0x74
#define AU6601_DLINK_MODE                       0x80
#define AU6601_INTERRUPT_DELAY_TIME             0x40
#define AU6601_SIGNAL_REQ_CTRL                  0x30
#define AU6601_MS_CARD_WP                       BIT(3)
#define AU6601_SD_CARD_WP                       BIT(0)

/* same register values are used for:
 *  - AU6601_OUTPUT_ENABLE
 *  - AU6601_POWER_CONTROL
 */
#define AU6601_ACTIVE_CTRL                      0x75
#define AU6601_XD_CARD                          BIT(4)
/* AU6601_MS_CARD_ACTIVE - will cativate MS card section? */
#define AU6601_MS_CARD                          BIT(3)
#define AU6601_SD_CARD                          BIT(0)

/* card slot state. It should automatically detect type of
 * the card
 */
#define AU6601_DETECT_STATUS                    0x76
#define AU6601_DETECT_EN                        BIT(7)
#define AU6601_MS_DETECTED                      BIT(3)
#define AU6601_SD_DETECTED                      BIT(0)
#define AU6601_DETECT_STATUS_M                  0xf

#define AU6601_REG_SW_RESET                     0x79
#define AU6601_BUF_CTRL_RESET                   BIT(7)
#define AU6601_RESET_DATA                       BIT(3)
#define AU6601_RESET_CMD                        BIT(0)

#define AU6601_OUTPUT_ENABLE                    0x7a

#define AU6601_PAD_DRIVE0                       0x7b
#define AU6601_PAD_DRIVE1                       0x7c
#define AU6601_PAD_DRIVE2                       0x7d
/* read EEPROM? */
#define AU6601_FUNCTION                         0x7f

#define AU6601_CMD_XFER_CTRL                    0x81
#define AU6601_CMD_17_BYTE_CRC                  0xc0
#define AU6601_CMD_6_BYTE_WO_CRC                0x80
#define AU6601_CMD_6_BYTE_CRC                   0x40
#define AU6601_CMD_START_XFER                   0x20
#define AU6601_CMD_STOP_WAIT_RDY                0x10
#define AU6601_CMD_NO_RESP                      0x00

#define AU6601_REG_BUS_CTRL                     0x82
#define AU6601_BUS_WIDTH_4BIT                   0x20
#define AU6601_BUS_WIDTH_8BIT                   0x10
#define AU6601_BUS_WIDTH_1BIT                   0x00

#define AU6601_DATA_XFER_CTRL                   0x83
#define AU6601_DATA_WRITE                       BIT(7)
#define AU6601_DATA_DMA_MODE                    BIT(6)
#define AU6601_DATA_START_XFER                  BIT(0)

#define AU6601_DATA_PIN_STATE                   0x84
#define AU6601_BUS_STAT_CMD                     BIT(15)
/* BIT(4) - BIT(7) are permanently 1.
 * May be reserved or not attached DAT4-DAT7
 */
#define AU6601_BUS_STAT_DAT3                    BIT(3)
#define AU6601_BUS_STAT_DAT2                    BIT(2)
#define AU6601_BUS_STAT_DAT1                    BIT(1)
#define AU6601_BUS_STAT_DAT0                    BIT(0)
#define AU6601_BUS_STAT_DAT_MASK                0xf

#define AU6601_OPT                              0x85
#define AU6601_OPT_CMD_LINE_LEVEL               0x80
#define AU6601_OPT_NCRC_16_CLK                  BIT(4)
#define AU6601_OPT_CMD_NWT                      BIT(3)
#define AU6601_OPT_STOP_CLK                     BIT(2)
#define AU6601_OPT_DDR_MODE                     BIT(1)
#define AU6601_OPT_SD_18V                       BIT(0)

#define AU6601_CLK_DELAY                        0x86
#define AU6601_CLK_DATA_POSITIVE_EDGE           0x80
#define AU6601_CLK_CMD_POSITIVE_EDGE            0x40
#define AU6601_CLK_POSITIVE_EDGE_ALL            (AU6601_CLK_CMD_POSITIVE_EDGE \
                                                | AU6601_CLK_DATA_POSITIVE_EDGE)


#define AU6601_REG_INT_STATUS                   0x90
#define AU6601_REG_INT_ENABLE                   0x94
#define AU6601_INT_DATA_END_BIT_ERR             BIT(22)
#define AU6601_INT_DATA_CRC_ERR                 BIT(21)
#define AU6601_INT_DATA_TIMEOUT_ERR             BIT(20)
#define AU6601_INT_CMD_INDEX_ERR                BIT(19)
#define AU6601_INT_CMD_END_BIT_ERR              BIT(18)
#define AU6601_INT_CMD_CRC_ERR                  BIT(17)
#define AU6601_INT_CMD_TIMEOUT_ERR              BIT(16)
#define AU6601_INT_ERROR                        BIT(15)
#define AU6601_INT_OVER_CURRENT_ERR             BIT(8)
#define AU6601_INT_CARD_INSERT                  BIT(7)
#define AU6601_INT_CARD_REMOVE                  BIT(6)
#define AU6601_INT_READ_BUF_RDY                 BIT(5)
#define AU6601_INT_WRITE_BUF_RDY                BIT(4)
#define AU6601_INT_DMA_END                      BIT(3)
#define AU6601_INT_DATA_END                     BIT(1)
#define AU6601_INT_CMD_END                      BIT(0)

#define AU6601_INT_NORMAL_MASK                  0x00007FFF
#define AU6601_INT_ERROR_MASK                   0xFFFF8000

#define AU6601_INT_CMD_MASK     (AU6601_INT_CMD_END | \
                AU6601_INT_CMD_TIMEOUT_ERR | AU6601_INT_CMD_CRC_ERR | \
                AU6601_INT_CMD_END_BIT_ERR | AU6601_INT_CMD_INDEX_ERR)
#define AU6601_INT_DATA_MASK    (AU6601_INT_DATA_END | AU6601_INT_DMA_END | \
                AU6601_INT_READ_BUF_RDY | AU6601_INT_WRITE_BUF_RDY | \
                AU6601_INT_DATA_TIMEOUT_ERR | AU6601_INT_DATA_CRC_ERR | \
                AU6601_INT_DATA_END_BIT_ERR)
#define AU6601_INT_ALL_MASK                     ((u32)-1)

/* MS_CARD mode registers */

#define AU6601_MS_STATUS                        0xa0

#define AU6601_MS_BUS_MODE_CTRL                 0xa1
#define AU6601_MS_BUS_8BIT_MODE                 0x03
#define AU6601_MS_BUS_4BIT_MODE                 0x01
#define AU6601_MS_BUS_1BIT_MODE                 0x00

#define AU6601_MS_TPC_CMD                       0xa2
#define AU6601_MS_TPC_READ_PAGE_DATA            0x02
#define AU6601_MS_TPC_READ_REG                  0x04
#define AU6601_MS_TPC_GET_INT                   0x07
#define AU6601_MS_TPC_WRITE_PAGE_DATA           0x0D
#define AU6601_MS_TPC_WRITE_REG                 0x0B
#define AU6601_MS_TPC_SET_RW_REG_ADRS           0x08
#define AU6601_MS_TPC_SET_CMD                   0x0E
#define AU6601_MS_TPC_EX_SET_CMD                0x09
#define AU6601_MS_TPC_READ_SHORT_DATA           0x03
#define AU6601_MS_TPC_WRITE_SHORT_DATA          0x0C

#define AU6601_MS_TRANSFER_MODE                 0xa3
#define AU6601_MS_XFER_INT_TIMEOUT_CHK          BIT(2)
#define AU6601_MS_XFER_DMA_ENABLE               BIT(1)
#define AU6601_MS_XFER_START                    BIT(0)

#define AU6601_MS_DATA_PIN_STATE                0xa4

#define AU6601_MS_INT_STATUS                    0xb0
#define AU6601_MS_INT_ENABLE                    0xb4
#define AU6601_MS_INT_OVER_CURRENT_ERROR        BIT(23)
#define AU6601_MS_INT_DATA_CRC_ERROR            BIT(21)
#define AU6601_MS_INT_INT_TIMEOUT               BIT(20)
#define AU6601_MS_INT_INT_RESP_ERROR            BIT(19)
#define AU6601_MS_INT_CED_ERROR                 BIT(18)
#define AU6601_MS_INT_TPC_TIMEOUT               BIT(16)
#define AU6601_MS_INT_ERROR                     BIT(15)
#define AU6601_MS_INT_CARD_INSERT               BIT(7)
#define AU6601_MS_INT_CARD_REMOVE               BIT(6)
#define AU6601_MS_INT_BUF_READ_RDY              BIT(5)
#define AU6601_MS_INT_BUF_WRITE_RDY             BIT(4)
#define AU6601_MS_INT_DMA_END                   BIT(3)
#define AU6601_MS_INT_TPC_END                   BIT(1)

#define AU6601_MS_INT_DATA_MASK                 0x00000038
#define AU6601_MS_INT_TPC_MASK                  0x003d8002
#define AU6601_MS_INT_TPC_ERROR                 0x003d0000

#define ALCOR_PCIE_LINK_CTRL_OFFSET             0x10
#define ALCOR_PCIE_LINK_CAP_OFFSET              0x0c
#define ALCOR_CAP_START_OFFSET                  0x34

struct alcor_dev_cfg {
        u8      dma;
};

struct alcor_pci_priv {
        struct pci_dev *pdev;
        struct pci_dev *parent_pdev;
        struct  device *dev;
        void __iomem *iobase;
        unsigned int irq;

        unsigned long id; /* idr id */

        struct alcor_dev_cfg    *cfg;
};

void alcor_write8(struct alcor_pci_priv *priv, u8 val, unsigned int addr);
void alcor_write16(struct alcor_pci_priv *priv, u16 val, unsigned int addr);
void alcor_write32(struct alcor_pci_priv *priv, u32 val, unsigned int addr);
void alcor_write32be(struct alcor_pci_priv *priv, u32 val, unsigned int addr);
u8 alcor_read8(struct alcor_pci_priv *priv, unsigned int addr);
u32 alcor_read32(struct alcor_pci_priv *priv, unsigned int addr);
u32 alcor_read32be(struct alcor_pci_priv *priv, unsigned int addr);
#endif
Linux
