/*- * Copyright (c) 1998, 1999 Scott Mitchell * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * $Id: if_xereg.h,v 1.5 1999/05/20 21:53:58 scott Exp $ * $FreeBSD: src/sys/dev/xe/if_xereg.h,v 1.6 2003/10/14 22:51:35 rsm Exp $ * $DragonFly: src/sys/dev/netif/xe/if_xereg.h,v 1.3 2005/11/20 10:16:56 sephe Exp $ */ #ifndef DEV_XE_IF_XEREG_H #define DEV_XE_IF_XEREG_H /* * Register definitions for Xircom PCMCIA Ethernet controllers, based on * Rev. B of the "Dingo" 10/100 controller used in Xircom CEM56 and RealPort * Ethernet/modem cards. The Dingo can be configured to be register * compatible with the "Mohawk" 10/100 controller used in Xircom CE3 cards * (also some Intel and Compaq OEM versions of the CE3). The older 10Mbps CE2 * cards seem to use earlier revisions of the same device. Some registers and * bits below are marked 'CE2 only'; these are used by Werner Koch's xirc2ps * driver that was originally for the CE2 but, according to the spec, aren't * present on the Dingo. They often seem to relate to operation on coax * cables, which Mohawk can do in theory (it has the SSI interface) so they * _might_ also work on Mohawk. I've also noted the few registers that are * specific to Dingo. * * As far as I can tell, the Dingo is basically a Mohawk device with a few * registers and support for a second PCMCIA function (the modem) added. In * Dingo mode the SSI (non-MII) PHY interface of the Mohawk is not available. * The CE2 chip is most likely a Mohawk without the MII and definitely with a * slightly different register set. * * In all cases, the controller uses a paged model of register access. The * first eight registers are always the same, the function of the second eight * is selected by the value in the Page Register (reg 0x01). * * References: * 1. Dingo External Reference Specification, Revision B. Xircom Inc., * Thousand Oaks, California. August 1998. Available under licence from * Xircom, http://www.xircom.com/ * 2. ML6692 100BASE-TX Physical Layer with MII specification. MicroLinear * Corp, San Jose, California. May 1997. Available for download from * http://www.microlinear.com/ * 3. DP83840 10/100 Mb/s Ethernet Physical Layer specification. National * Semiconductor Corp., Arlington, Texas. March 1997. Available for * download from http://www.ns.com/ * 4. Werner Koch's xirc2ps driver for Linux, for all the CE2 and CE3 frobs * that aren't documented in the Xircom spec. Available for download from * http://www.d.shuttle.de/isil/xircom/xirc2ps.html */ /******************* * PCMCIA registers *******************/ /* * These are probably Dingo-specific, but you won't need them unless you have * a CEM card that needs a bit of hackery to get the Ethernet function to * operate. All addresses are in card attribute space. */ #define DINGO_CIS 0x0000 /* Start of CIS tuples */ #define DINGO_ETH 0x0800 /* Ethernet configuration registers */ #define DINGO_COR 0x0820 /* Dingo configuration option registers */ #define DINGO_2ND 0x0840 /* 2nd function configuration registers */ /* * Ethernet configuration registers */ #define DINGO_ECOR (DINGO_ETH+0) /* Ethernet Configuration Option Register */ #define DINGO_ECSR (DINGO_ETH+2) /* Ethernet Configuration Status Register */ #define DINGO_EBAR0 (DINGO_ETH+10) /* Ethernet Base Address Register bits 7:4 (3:0 always 0) */ #define DINGO_EBAR1 (DINGO_ETH+12) /* Ethernet Base Address Register bits 15:8 */ /* DINGO_ECOR bits */ #define DINGO_ECOR_ETH_ENABLE 0x01 /* 1 = Enable Ethernet part of adapter */ #define DINGO_ECOR_IOB_ENABLE 0x02 /* 1 = Enable EBAR, else use INDEX bits */ #define DINGO_ECOR_INT_ENABLE 0x04 /* 1 = Enable Ethernet interrupts */ #define DINGO_ECOR_IOB_INDEX 0x18 /* 00 = 0x300; 01 = 0x310; 10 = 0x320; 11 = no IO base */ #define DINGO_ECOR_IOB_SHIFT 0x03 #define DINGO_ECOR_IRQ_STSCHG 0x20 /* 1 = Route interrupts to -STSCHG pin, else use -INT pin */ #define DINGO_ECOR_IRQ_LEVEL 0x40 /* 1 = Level-triggered interrupts, else edge-triggered */ #define DINGO_ECOR_SRESET 0x80 /* 1 = Soft reset Ethernet adpater. Must write to 0 */ /* DINGO_ECSR bits */ #define DINGO_ECSR_INT_ACK 0x01 /* 1 = Host must acknowledge interrupts (Clear ECSR_INT bit) */ #define DINGO_ECSR_INT 0x02 /* 1 = Interrupt service requested */ #define DINGO_ECSR_POWER_DOWN 0x04 /* 1 = Power down Ethernet adapter */ /* * EBAR0/EBAR1 set the I/O base address of the Ethernet adapter when * ECOR_IOB_ENABLE is set. 12 significant bits. */ /* * Dingo configuration registers */ #define DINGO_DCOR0 (DINGO_COR+0) /* Dingo Configuration Options Register 0 */ #define DINGO_DCOR1 (DINGO_COR+2) /* Dingo Configuration Options Register 1 */ #define DINGO_DCOR2 (DINGO_COR+4) /* Dingo Configuration Options Register 2 */ #define DINGO_DCOR3 (DINGO_COR+6) /* Dingo Configuration Options Register 3 */ #define DINGO_DCOR4 (DINGO_COR+8) /* Dingo Configuration Options Register 4 */ /* DINGO_DCOR0 bits */ #define DINGO_DCOR0_SF_INT 0x01 /* 1 = Enable 2ndF interrupts (alternate to SFCOR:2) */ #define DINGO_DCOR0_DECODE 0x04 /* 1 = Decode 2ndF interrupts in Dingo, else in 2ndF */ #define DINGO_DCOR0_BUS 0x08 /* 1 = 2ndF bus is ISA, else PCMCIA */ #define DINGO_DCOR0_LED3_POWER 0x10 /* 1 = Drive LED3 line from SFCSR:2 */ #define DINGO_DCOR0_LED3_RESET 0x20 /* 1 = Drive LED3 line from SFCOR:7 */ #define DINGO_DCOR0_MR_POWER 0x40 /* 1 = Drive MRESET line from SFCSR:2 */ #define DINGO_DCOR0_MR_RESET 0x80 /* 1 = Drive MRESET line from SFCOR:7 */ /* DINGO_DCOR1 bits */ #define DINGO_DCOR1_INT_STSCHG 0x01 /* 1 = Route 2ndF interrupts to -STSCHG (alternate to SFCOR:5) */ #define DINGO_DCOR1_MSTSCHG 0x02 /* 1 = Route 2ndF -MSTSCHG line to -STSCHG */ #define DINGO_DCOR1_EEDIO 0x04 /* 1 = Use EEDIO pin as data line 6 to 2ndF */ #define DINGO_DCOR1_INT_LEVEL 0x08 /* 1 = Force level-triggered interrupts from 2ndF */ #define DINGO_DCOR1_SHADOW_CSR 0x10 /* Reserved, always write 0 */ #define DINGO_DCOR1_SHADOW_IOB 0x20 /* Reserved, always write 0 */ #define DINGO_DCOR1_CSR_WAIT 0xC0 /* Reserved, always write 0 */ #define DINGO_DCOR1_CSR_SHIFT 0x06 /* DINGO_DCOR2 bits */ #define DINGO_DCOR2_SHM_BASE 0x0f /* Bits 15-12 of Ethernet shared memory window */ #define DINGO_DCOR2_SHM_SHIFT 0x00 #define DINGO_DCOR2_SHADOW_COR 0x10 /* Reserved, always write 0 */ /* * DCOR3/DCOR4 configure Dingo to assert -IOIS16 on any access to each pair of * ports in the range SFIOB+0 .. SFIOB+31. Each pair can be set individually, * eg. DCOR3:0 enables this function on ports SFIOB+0 and SFIOB+1. */ /* * Second function configuration registers */ #define DINGO_SFCOR (DINGO_2ND+0) /* 2nd Function Configuration Option Register */ #define DINGO_SFCSR (DINGO_2ND+2) /* 2nd Function Configuration Status Register */ #define DINGO_SFBAR0 (DINGO_2ND+10) /* 2nd Function Base Address Register bits 7:0 */ #define DINGO_SFBAR1 (DINGO_2ND+12) /* 2nd Function Base Address Register bits 15:8 */ #define DINGO_SFILR (DINGO_2ND+18) /* 2nd Function I/O Limit Register */ /* DINGO_SFCOR bits */ #define DINGO_SFCOR_SF_ENABLE 0x01 /* 1 = Enable second fuction */ #define DINGO_SFCOR_IOB_ENABLE 0x02 /* 1 = Enable SFBAR, else use COM_SELECT bits */ #define DINGO_SFCOR_INT_ENABLE 0x04 /* 1 = Enable second function interrupts */ #define DINGO_SFCOR_COM_SELECT 0x18 /* 00 = 0x3f8; 01 = 0x2f8; 10 = 0x3e8; 11 = 0x2e8 */ #define DINGO_SFCOR_COM_SHIFT 0x03 #define DINGO_SFCOR_IRQ_STSCHG 0x20 /* 1 = Route interrupts to -STSCHG pin, else use -INT pin */ #define DINGO_SFCOR_IRQ_LEVEL 0x40 /* 1 = Level-triggered interrupts, else edge-triggered */ #define DINGO_SFCOR_SRESET 0x80 /* 1 = Soft reset second function. Must write to 0 */ /* DINGO_SFCSR bits */ #define DINGO_SFCSR_INT_ACK 0x01 /* 1 = Host must acknowledge interrupts (Clear SFCSR_INT bit) */ #define DINGO_SFCSR_INT 0x02 /* 1 = Interrupt service requested */ #define DINGO_SFCSR_POWER_DOWN 0x04 /* 1 = Power down second function */ /* * SFBAR0/SFBAR1 set the I/O base address of the second function when * SFCOR_IOB_ENABLE is set. 16 significant bits. */ /* * SFILR is a bitmap of address lines 7:0 decoded by the second function * device. Eg. a device with 16 ports should write 0x0f to this register. */ /******************************** * Ethernet controller registers ********************************/ /* * Common registers (available from any register page) * * Note: The EDP is actually 32 bits wide, occupying registers 2-5. In PCMCIA * operation we can only access 16 bits at once, through registers 4 & 5. */ #define XE_CR 0x00 /* Command register (write) */ #define XE_ESR 0x00 /* Ethernet status register (read) */ #define XE_PR 0x01 /* Page select register */ #define XE_EDP 0x04 /* Ethernet data port */ #define XE_ISR 0x06 /* Ethernet interrupt status register (read) */ #define XE_GIR 0x07 /* Global interrupt register (Dingo only) */ /* XE_CR bits */ #define XE_CR_TX_PACKET 0x01 /* Transmit packet */ #define XE_CR_SOFT_RESET 0x02 /* Software reset */ #define XE_CR_ENABLE_INTR 0x04 /* Enable interrupts */ #define XE_CR_FORCE_INTR 0x08 /* Force an interrupt */ #define XE_CR_CLEAR_FIFO 0x10 /* Clear FIFO after transmit overrun */ #define XE_CR_CLEAR_OVERRUN 0x20 /* Clear receive overrun condition */ #define XE_CR_RESTART_TX 0x40 /* Restart TX after 16 collisions or TX underrun */ /* XE_ESR bits */ #define XE_ESR_FULL_PACKET_RX 0x01 /* At least one full packet received */ #define XE_ESR_PART_PACKET_RX 0x02 /* At least 64 bytes of packet received */ #define XE_ESR_REJECT_PACKET 0x04 /* Partial packet rejected */ #define XE_ESR_TX_PENDING 0x08 /* At least one packet waiting to transmit */ #define XE_ESR_BAD_POLARITY 0x10 /* Bad cable polarity? (CE2 only) */ #define XE_ESR_MEDIA_SELECT 0x20 /* SSI(?) media select: 1 = Twisted pair; 0 = AUI */ /* XE_ISR bits */ #define XE_ISR_TX_OVERFLOW 0x01 /* No space in transmit buffer */ #define XE_ISR_TX_PACKET 0x02 /* Packet sent successfully */ #define XE_ISR_MAC_INTR 0x04 /* Some kind of MAC interrupt happened */ #define XE_ISR_RX_EARLY 0x10 /* Incoming packet in early receive mode */ #define XE_ISR_RX_PACKET 0x20 /* Complete packet received successfully */ #define XE_ISR_RX_REJECT 0x40 /* Partial incoming packet rejected by MAC */ #define XE_ISR_FORCE_INTR 0x80 /* Interrupt forced */ /* XE_GIR bits */ #define XE_GIR_ETH_IRQ 0x01 /* Ethernet IRQ pending */ #define XE_GIR_ETH_MASK 0x02 /* 1 = Mask Ethernet interrupts to host */ #define XE_GIR_SF_IRQ 0x04 /* Second function IRQ pending */ #define XE_GIR_SF_MASK 0x08 /* 1 = Mask second function interrupts to host */ /* * Page 0 registers */ #define XE_TSO 0x08 /* Transmit space open (17 bits) */ #define XE_TRS 0x0a /* Transmit reservation size (CE2 only, removed in rev. 1) */ #define XE_DO 0x0c /* Data offset register (13 bits/3 flags, write) */ #define XE_RSR 0x0c /* Receive status register (read) */ #define XE_TPR 0x0d /* Packets transmitted register (read) */ #define XE_RBC 0x0e /* Received byte count (13 bits/3 flags, read) */ /* XE_DO bits */ #define XE_DO_OFFSET 0x1fff /* First byte fetched when CHANGE_OFFSET issued */ #define XE_DO_OFFSET_SHIFT 0x00 #define XE_DO_CHANGE_OFFSET 0x2000 /* Flush RX FIFO, start fetching from OFFSET */ #define XE_DO_SHARED_MEM 0x4000 /* Enable shared memory mode */ #define XE_DO_SKIP_RX_PACKET 0x8000 /* Skip to next packet in buffer memory */ /* XE_RSR bits */ #define XE_RSR_PHYS_PACKET 0x01 /* 1 = Physical packet, 0 = Multicast packet */ #define XE_RSR_BCAST_PACKET 0x02 /* Broadcast packet */ #define XE_RSR_LONG_PACKET 0x04 /* Packet >1518 bytes */ #define XE_RSR_ADDR_MATCH 0x08 /* Packet matched one of our node addresses */ #define XE_RSR_ALIGN_ERROR 0x10 /* Bad alignment? (CE2 only) */ #define XE_RSR_CRC_ERROR 0x20 /* Incorrect CRC */ #define XE_RSR_RX_OK 0x80 /* No errors on received packet */ /* XE_RBC bits */ #define XE_RBC_BYTE_COUNT 0x1fff /* Bytes received for current packet */ #define XE_RBC_COUNT_SHIFT 0x00 #define XE_RBC_FULL_PACKET_RX 0x2000 /* These mirror bits 2:0 of ESR, if ECR:7 is set */ #define XE_RBC_PART_PACKET_RX 0x4000 #define XE_RBC_REJECT_PACKET 0x8000 /* * Page 1 registers */ #define XE_IMR0 0x0c /* Interrupt mask register 0 */ #define XE_IMR1 0x0d /* Interrupt mask register 1 (CE2 only) */ #define XE_ECR 0x0e /* Ethernet configuration register */ /* XE_IMR0 bits */ #define XE_IMR0_TX_OVERFLOW 0x01 /* Masks for bits in ISR */ #define XE_IMR0_TX_PACKET 0x02 #define XE_IMR0_MAC_INTR 0x04 #define XE_IMR0_TX_RESGRANT 0x08 /* Tx reservation granted (CE2) */ #define XE_IMR0_RX_EARLY 0x10 #define XE_IMR0_RX_PACKET 0x20 #define XE_IMR0_RX_REJECT 0x40 #define XE_IMR0_FORCE_INTR 0x80 /* XE_IMR1 bits */ #define XE_IMR1_TX_UNDERRUN 0x01 /* XE_ECR bits */ #define XE_ECR_EARLY_TX 0x01 /* Enable early transmit mode */ #define XE_ECR_EARLY_RX 0x02 /* Enable early receive mode */ #define XE_ECR_FULL_DUPLEX 0x04 /* Enable full-duplex (disable collision detection) */ #define XE_ECR_LONG_TPCABLE 0x08 /* CE2 only */ #define XE_ECR_NO_POL_COL 0x10 /* CE2 only */ #define XE_ECR_NO_LINK_PULSE 0x20 /* Don't check/send link pulses (not 10BT compliant) */ #define XE_ECR_NO_AUTO_TX 0x40 /* CE2 only */ #define XE_ECR_SOFT_COMPAT 0x80 /* Map ESR bits 2:0 to RBC bits 15:13 */ /* * Page 2 registers */ #define XE_RBS 0x08 /* Receive buffer start (16 bits) */ #define XE_LED 0x0a /* LED control register */ #define XE_LED3 0x0b /* LED3 control register */ #define XE_MSR 0x0c /* Misc. setup register (Mohawk specific register?) */ #define XE_GPR2 0x0d /* General purpose register 2 */ /* * LED function selection: * 000 - Disabled * 001 - Collision activity * 010 - !Collision activity * 011 - 10Mbit link detected * 100 - 100Mbit link detected * 101 - 10/100Mbit link detected * 110 - Automatic assertion * 111 - Transmit activity */ /* XE_LED bits */ #define XE_LED_LED0_MASK 0x07 /* LED0 function selection */ #define XE_LED_LED0_SHIFT 0x00 #define XE_LED_LED1_MASK 0x38 /* LED1 function selection */ #define XE_LED_LED1_SHIFT 0x03 #define XE_LED_LED0_RX 0x40 /* Add receive activity to LED0 */ #define XE_LED_LED1_RX 0x80 /* Add receive activity to LED1 */ /* XE_LED3 bits */ #define XE_LED3_MASK 0x07 /* LED3 function selection */ #define XE_LED3_SHIFT 0x00 #define XE_LED3_RX 0x40 /* Add receive activity to LED3 */ /* XE_MSR bits */ #define XE_MSR_128K_SRAM 0x01 /* Select 128K SRAM */ #define XE_MSR_RBS_BIT16 0x02 /* Bit 16 of RBS (only useful with big SRAM) */ #define XE_MSR_MII_SELECT 0x08 /* Select MII instead of SSI interface */ #define XE_MSR_HASH_TABLE 0x20 /* Enable hash table filtering */ /* XE_GPR2 bits */ #define XE_GPR2_GP3_OUT 0x01 /* Value written to GP3 line */ #define XE_GPR2_GP4_OUT 0x02 /* Value written to GP4 line */ #define XE_GPR2_GP3_SELECT 0x04 /* 1 = GP3 is output, 0 = GP3 is input */ #define XE_GPR2_GP4_SELECT 0x08 /* 1 = GP4 is output, 0 = GP3 is input */ #define XE_GPR2_GP3_IN 0x10 /* Value read from GP3 line */ #define XE_GPR2_GP4_IN 0x20 /* Value read from GP4 line */ /* * Page 3 registers */ #define XE_TPT 0x0a /* Transmit packet threshold (13 bits) */ /* * Page 4 registers */ #define XE_GPR0 0x08 /* General purpose register 0 */ #define XE_GPR1 0x09 /* General purpose register 1 */ #define XE_BOV 0x0a /* Bonding version register (read) */ #define XE_EES 0x0b /* EEPROM control register */ #define XE_LMA 0x0c /* Local memory address (CE2 only) */ #define XE_LMD 0x0e /* Local memory data (CE2 only) */ /* XE_GPR0 bits */ #define XE_GPR0_GP1_OUT 0x01 /* Value written to GP1 line */ #define XE_GPR0_GP2_OUT 0x02 /* Value wirtten to GP2 line */ #define XE_GPR0_GP1_SELECT 0x04 /* 1 = GP1 is output, 0 = GP1 is input */ #define XE_GPR0_GP2_SELECT 0x08 /* 1 = GP2 is output, 0 = GP2 is input */ #define XE_GPR0_GP1_IN 0x10 /* Value read from GP1 line */ #define XE_GPR0_GP2_IN 0x20 /* Value read from GP2 line */ /* XE_GPR1 bits */ #define XE_GPR1_POWER_DOWN 0x01 /* 0 = Power down analog section */ #define XE_GPR1_AIC 0x04 /* AIC bit (CE2 only) */ /* XE_BOV values */ #define XE_BOV_DINGO 0x55 /* Dingo in Dingo mode */ #define XE_BOV_MOHAWK 0x41 /* Original Mohawk */ #define XE_BOV_MOHAWK_REV1 0x45 /* Rev. 1 Mohawk, or Dingo in Mohawk mode */ #define XE_BOV_CEM28 0x11 /* CEM28 */ /* XE_EES bits */ #define XE_EES_SCL_OUTPUT 0x01 /* Value written to SCL line, when MANUAL_ROM set */ #define XE_EES_SDA_OUTPUT 0x02 /* Value written to SDA line, when MANUAL_ROM set */ #define XE_EES_SDA_INPUT 0x04 /* Value read from SDA line */ #define XE_EES_SDA_TRISTATE 0x08 /* 1 = SDA is output, 0 = SDA is input */ #define XE_EES_MANUAL_ROM 0x20 /* Enable manual contro of serial EEPROM */ /* * Page 5 registers (all read only) */ #define XE_CRHA 0x08 /* Current Rx host address (16 bits) */ #define XE_RHSA 0x0a /* Rx host start address (16 bits) */ #define XE_RNSA 0x0c /* Rx network start address (16 bits) */ #define XE_CRNA 0x0e /* Current Rx network address (16 bits) */ /* * Page 6 registers (all read only) */ #define XE_CTHA 0x08 /* Current Tx host address (16 bits) */ #define XE_THSA 0x0a /* Tx host start address (16 bits) */ #define XE_TNSA 0x0c /* Tx network statr address (16 bits) */ #define XE_CTNA 0x0e /* Current Tx network address (16 bits) */ /* * Page 8 registers (all read only) */ #define XE_THBC 0x08 /* Tx host byte count (16 bits) */ #define XE_THPS 0x0a /* Tx host packet size (16 bits) */ #define XE_TNBC 0x0c /* Tx network byte count (16 bits) */ #define XE_TNPS 0x0e /* Tx network packet size (16 bits) */ /* * Page 0x10 registers (all read only) */ #define XE_DINGOID 0x08 /* Dingo ID register (16 bits) (Dingo only) */ #define XE_RevID 0x0a /* Dingo revision ID (16 bits) (Dingo only) */ #define XE_VendorID 0x0c /* Dingo vendor ID (16 bits) (Dingo only) */ /* Values for the above registers */ #define XE_DINGOID_DINGO3 0x444b /* In both Dingo and Mohawk modes */ #define XE_RevID_DINGO3 0x0001 #define XE_VendorID_DINGO3 0x0041 /* * Page 0x40 registers */ #define XE_CMD0 0x08 /* MAC Command register (write) */ #define XE_RST0 0x09 /* Receive status register */ #define XE_TXST0 0x0b /* Transmit status register 0 */ #define XE_TXST1 0x0c /* Transmit status register 1 */ #define XE_RX0Msk 0x0d /* Receive status mask register */ #define XE_TX0Msk 0x0e /* Transmit status 0 mask register */ #define XE_TX1Msk 0x0f /* Transmit status 1 mask register */ /* CMD0 bits */ #define XE_CMD0_TX 0x01 /* CE2 only */ #define XE_CMD0_RX_ENABLE 0x04 /* Enable receiver */ #define XE_CMD0_RX_DISABLE 0x08 /* Disable receiver */ #define XE_CMD0_ABORT 0x10 /* CE2 only */ #define XE_CMD0_ONLINE 0x20 /* Take MAC online */ #define XE_CMD0_ACK_INTR 0x40 /* CE2 only */ #define XE_CMD0_OFFLINE 0x80 /* Take MAC offline */ /* RST0 bits */ #define XE_RST0_LONG_PACKET 0x02 /* Packet received with >1518 and <8184 bytes */ #define XE_RST0_CRC_ERROR 0x08 /* Packet received with incorrect CRC */ #define XE_RST0_RX_OVERRUN 0x10 /* Receiver overrun, byte(s) dropped */ #define XE_RST0_RX_ENABLE 0x20 /* Receiver enabled */ #define XE_RST0_RX_ABORT 0x40 /* Receive aborted: CRC, FIFO overrun or addr mismatch */ #define XE_RST0_RX_OK 0x80 /* Complete packet received OK */ /* TXST0 bits */ #define XE_TXST0_NO_CARRIER 0x01 /* Lost carrier. Only valid in 10Mbit half-duplex */ #define XE_TXST0_16_COLLISIONS 0x02 /* Packet aborted after 16 collisions */ #define XE_TXST0_TX_UNDERRUN 0x08 /* MAC ran out of data to send */ #define XE_TXST0_LATE_COLLISION 0x10 /* Collision later than 512 bits */ #define XE_TXST0_SQE_FAIL 0x20 /* SQE test failed. */ #define XE_TXST0_TX_ABORT 0x40 /* Transmit aborted: collisions, underrun or overrun */ #define XE_TXST0_TX_OK 0x80 /* Complete packet sent OK */ /* TXST1 bits */ #define XE_TXST1_RETRY_COUNT 0x0f /* Collision counter for current packet */ #define XE_TXST1_LINK_STATUS 0x10 /* Valid link status */ /* RX0Msk bits */ #define XE_RX0M_MP 0x01 /* Multicast packet? (CE2 only) */ #define XE_RX0M_LONG_PACKET 0x02 /* Masks for bits in RXST0 */ #define XE_RX0M_ALIGN_ERROR 0x04 /* Alignment error (CE2 only) */ #define XE_RX0M_CRC_ERROR 0x08 #define XE_RX0M_RX_OVERRUN 0x10 #define XE_RX0M_RX_ABORT 0x40 #define XE_RX0M_RX_OK 0x80 /* TX0Msk bits */ #define XE_TX0M_NO_CARRIER 0x01 /* Masks for bits in TXST0 */ #define XE_TX0M_16_COLLISIONS 0x02 #define XE_TX0M_TX_UNDERRUN 0x08 #define XE_TX0M_LATE_COLLISION 0x10 #define XE_TX0M_SQE_FAIL 0x20 #define XE_TX0M_TX_ABORT 0x40 #define XE_TX0M_TX_OK 0x80 /* TX1Msk bits */ #define XE_TX1M_PKTDEF 0x20 /* * Page 0x42 registers */ #define XE_SWC0 0x08 /* Software configuration 0 */ #define XE_SWC1 0x09 /* Software configuration 1 */ #define XE_BOC 0x0a /* Back-off configuration */ #define XE_TCD 0x0b /* Transmit collision deferral */ /* SWC0 bits */ #define XE_SWC0_LOOPBACK_ENABLE 0x01 /* Enable loopback operation */ #define XE_SWC0_LOOPBACK_SOURCE 0x02 /* 1 = Transceiver, 0 = MAC */ #define XE_SWC0_ACCEPT_ERROR 0x04 /* Accept otherwise OK packets with CRC errors */ #define XE_SWC0_ACCEPT_SHORT 0x08 /* Accept otherwise OK packets that are too short */ #define XE_SWC0_NO_SRC_INSERT 0x20 /* Disable source insertion (CE2) */ #define XE_SWC0_NO_CRC_INSERT 0x40 /* Don't add CRC to outgoing packets */ /* SWC1 bits */ #define XE_SWC1_IA_ENABLE 0x01 /* Enable individual address filters */ #define XE_SWC1_ALLMULTI 0x02 /* Accept all multicast packets */ #define XE_SWC1_PROMISCUOUS 0x04 /* Accept all non-multicast packets */ #define XE_SWC1_BCAST_DISABLE 0x08 /* Reject broadcast packets */ #define XE_SWC1_MEDIA_SELECT 0x40 /* AUI media select (Mohawk only) */ #define XE_SWC1_AUTO_MEDIA 0x80 /* Auto media select (Mohawk only) */ /* * Page 0x44 registers (CE2 only) */ #define XE_TDR0 0x08 /* Time domain reflectometry register 0 */ #define XE_TDR1 0x09 /* Time domain reflectometry register 1 */ #define XE_RXC0 0x0a /* Receive byte count low */ #define XE_RXC1 0x0b /* Receive byte count high */ /* * Page 0x45 registers (CE2 only) */ #define XE_REV 0x0f /* Revision (read) */ /* * Page 0x50-0x57: Individual address 0-9 * * Used to filter incoming packets by matching against individual node * addresses. If IA matching is enabled (SWC1, bit0) any incoming packet with * a destination matching one of these 10 addresses will be received. IA0 is * always enabled and usually matches the card's unique address. * * Addresses are stored LSB first, ie. IA00 (reg. 8 on page 0x50) contains the * LSB of IA0, and so on. The data is stored contiguously, in that addresses * can be broken across page boundaries. That is: * * Reg: 50/8 50/9 50/a 50/b 50/c 50/d 50/e 50/f 51/8 51/9 ... 57/a 57/b * IA00 IA01 IA02 IA03 IA04 IA05 IA10 IA11 IA12 IA13 ... IA94 IA95 */ /* * Page 0x58: Multicast hash table filter * * In case the 10 individual addresses aren't enough, we also have a multicast * hash filter, enabled through MSR:5. The most significant six bits of the * CRC on each incoming packet are reversed and used as an index into the 64 * bits of the hash table. If the appropriate bit is set the packet it * received, although higher layers may still need to filter it out. The CRC * calculation is as follows: * * crc = 0xffffffff; * poly = 0x04c11db6; * for (i = 0; i < 6; i++) { * current = mcast_addr[i]; * for (k = 1; k <= 8; k++) { * if (crc & 0x80000000); * crc31 = 0x01; * else * crc31 = 0; * bit = crc31 ^ (current & 0x01); * crc <<= 1; * current >>= 1; * if (bit) * crc = (crc ^ poly)|1 * } * } */ /**************** * MII registers ****************/ /* * Basic MII-compliant PHY register definitions. According to the Dingo spec, * PHYs from (at least) MicroLinear, National Semiconductor, ICS, TDK and * Quality Semiconductor have been used. These apparently all come up with * PHY ID 0x00 unless the "interceptor module" on the Dingo 3 is in use. With * the interceptor enabled, the PHY is faked up to look like an ICS unit with * ID 0x16. The interceptor can be enabled/disabled in software. * * The ML6692 (and maybe others) doesn't have a 10Mbps mode -- this is handled * by an internal 10Mbps transceiver that we know nothing about... some cards * seem to work with the MII in 10Mbps mode, so I guess some PHYs must support * it. The question is, how can you figure out which one you have? Just to * add to the fun there are also 10Mbps _only_ Mohawk/Dingo cards. Aaargh! */ /* * Masks for the MII-related bits in GPR2 */ #define XE_MII_CLK XE_GPR2_GP3_OUT #define XE_MII_DIR XE_GPR2_GP4_SELECT #define XE_MII_WRD XE_GPR2_GP4_OUT #define XE_MII_RDD XE_GPR2_GP4_IN /* * MII PHY ID register values */ #define PHY_ID_ML6692 0x0000 /* MicroLinear ML6692? Or unknown */ #define PHY_ID_ICS1890 0x0015 /* ICS1890 */ #define PHY_ID_QS6612 0x0181 /* Quality QS6612 */ #define PHY_ID_DP83840 0x2000 /* National DP83840 */ /* * MII command (etc) bit strings. */ #define XE_MII_STARTDELIM 0x01 #define XE_MII_READOP 0x02 #define XE_MII_WRITEOP 0x01 #define XE_MII_TURNAROUND 0x02 /* * PHY registers. */ #define PHY_BMCR 0x00 /* Basic Mode Control Register */ #define PHY_BMSR 0x01 /* Basic Mode Status Register */ #define PHY_ID1 0x02 /* PHY ID 1 */ #define PHY_ID2 0x03 /* PHY ID 2 */ #define PHY_ANAR 0x04 /* Auto-Negotiation Advertisment Register */ #define PHY_LPAR 0x05 /* Auto-Negotiation Link Partner Ability Register */ #define PHY_ANER 0x06 /* Auto-Negotiation Expansion Register */ /* BMCR bits */ #define PHY_BMCR_RESET 0x8000 /* Soft reset PHY. Self-clearing */ #define PHY_BMCR_LOOPBK 0x4000 /* Enable loopback */ #define PHY_BMCR_SPEEDSEL 0x2000 /* 1=100Mbps, 0=10Mbps */ #define PHY_BMCR_AUTONEGENBL 0x1000 /* Auto-negotiation enabled */ #define PHY_BMCR_ISOLATE 0x0400 /* Isolate ML6692 from MII */ #define PHY_BMCR_AUTONEGRSTR 0x0200 /* Restart auto-negotiation. Self-clearing */ #define PHY_BMCR_DUPLEX 0x0100 /* Full duplex operation */ #define PHY_BMCR_COLLTEST 0x0080 /* Enable collision test */ /* BMSR bits */ #define PHY_BMSR_100BT4 0x8000 /* 100Base-T4 capable */ #define PHY_BMSR_100BTXFULL 0x4000 /* 100Base-TX full duplex capable */ #define PHY_BMSR_100BTXHALF 0x2000 /* 100Base-TX half duplex capable */ #define PHY_BMSR_10BTFULL 0x1000 /* 10Base-T full duplex capable */ #define PHY_BMSR_10BTHALF 0x0800 /* 10Base-T half duplex capable */ #define PHY_BMSR_AUTONEGCOMP 0x0020 /* Auto-negotiation complete */ #define PHY_BMSR_CANAUTONEG 0x0008 /* Auto-negotiation supported */ #define PHY_BMSR_LINKSTAT 0x0004 /* Link is up */ #define PHY_BMSR_EXTENDED 0x0001 /* Extended register capabilities */ /* ANAR bits */ #define PHY_ANAR_NEXTPAGE 0x8000 /* Additional link code word pages */ #define PHY_ANAR_TLRFLT 0x2000 /* Remote wire fault detected */ #define PHY_ANAR_100BT4 0x0200 /* 100Base-T4 capable */ #define PHY_ANAR_100BTXFULL 0x0100 /* 100Base-TX full duplex capable */ #define PHY_ANAR_100BTXHALF 0x0080 /* 100Base-TX half duplex capable */ #define PHY_ANAR_10BTFULL 0x0040 /* 10Base-T full duplex capable */ #define PHY_ANAR_10BTHALF 0x0020 /* 10Base-T half duplex capable */ #define PHY_ANAR_PROTO4 0x0010 /* Protocol selection (00001 = 802.3) */ #define PHY_ANAR_PROTO3 0x0008 #define PHY_ANAR_PROTO2 0x0004 #define PHY_ANAR_PROTO1 0x0002 #define PHY_ANAR_PROTO0 0x0001 #define PHY_ANAR_8023 PHY_ANAR_PROTO0 #define PHY_ANAR_DINGO PHY_ANAR_100BT+PHY_ANAR_10BT_FD+PHY_ANAR_10BT+PHY_ANAR_8023 #define PHY_ANAR_MOHAWK PHY_ANAR_100BT+PHY_ANAR_10BT_FD+PHY_ANAR_10BT+PHY_ANAR_8023 /* LPAR bits */ #define PHY_LPAR_NEXTPAGE 0x8000 /* Additional link code word pages */ #define PHY_LPAR_LPACK 0x4000 /* Link partner acknowledged receipt */ #define PHY_LPAR_TLRFLT 0x2000 /* Remote wire fault detected */ #define PHY_LPAR_100BT4 0x0200 /* 100Base-T4 capable */ #define PHY_LPAR_100BTXFULL 0x0100 /* 100Base-TX full duplex capable */ #define PHY_LPAR_100BTXHALF 0x0080 /* 100Base-TX half duplex capable */ #define PHY_LPAR_10BTFULL 0x0040 /* 10Base-T full duplex capable */ #define PHY_LPAR_10BTHALF 0x0020 /* 10Base-T half duplex capable */ #define PHY_LPAR_PROTO4 0x0010 /* Protocol selection (00001 = 802.3) */ #define PHY_LPAR_PROTO3 0x0008 #define PHY_LPAR_PROTO2 0x0004 #define PHY_LPAR_PROTO1 0x0002 #define PHY_LPAR_PROTO0 0x0001 /* ANER bits */ #define PHY_ANER_MLFAULT 0x0010 /* More than one link is up! */ #define PHY_ANER_LPNPABLE 0x0008 /* Link partner supports next page */ #define PHY_ANER_NPABLE 0x0004 /* Local port supports next page */ #define PHY_ANER_PAGERX 0x0002 /* Page received */ #define PHY_ANER_LPAUTONEG 0x0001 /* Link partner can auto-negotiate */ #endif /* DEV_XE_IF_XEREG_H */
