/* $OpenBSD: icsphyreg.h,v 1.3 2008/06/26 05:42:16 ray Exp $ */ /* $NetBSD: icsphyreg.h,v 1.1 1998/11/02 23:46:20 thorpej Exp $ */ /*- * Copyright (c) 1998 The NetBSD Foundation, Inc. * All rights reserved. * * This code is derived from software contributed to The NetBSD Foundation * by Jason R. Thorpe of the Numerical Aerospace Simulation Facility, * NASA Ames Research Center. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ #ifndef _DEV_MII_ICSPHYREG_H_ #define _DEV_MII_ICSPHYREG_H_ /* * Register definitions for the ICS1890 Ethernet PHY * Further documentation can be found at: * http://www.icst.com/products/pinfo/1890.htm */ #define MII_ICSPHY_ECR 0x10 /* Extended Control Register */ #define ECR_OVR 0x8000 /* disable command reg overwrites */ #define ECR_PHYADDR_MASK 0x07c0 /* PHY address mask */ #define ECR_CTEST 0x0020 /* Stream Cipher Test Mode */ #define ECR_IECT 0x0004 /* Invalid Error Code Test */ #define ECR_SSD 0x0001 /* Stream Cipher Disable */ #define MII_ICSPHY_QPR 0x11 /* Quick Poll Register */ #define QPR_SPEED 0x8000 /* 100Mbps */ #define QPR_FDX 0x4000 /* Full dupled */ #define QPR_ANB2 0x2000 /* Autoneg monitor bit 2 */ #define QPR_ANB1 0x1000 /* Autoneg monitor bit 1 */ #define QPR_ANB0 0x0800 /* Autoneg monitor bit 0 */ #define QPR_RXERR 0x0400 /* Receive signal lost */ #define QPR_PLLERR 0x0200 /* PLL error */ #define QPR_FCARR 0x0100 /* False carrier detected */ #define QPR_INVALSYM 0x0080 /* Invalid Symbol Detected */ #define QPR_HALT 0x0040 /* Halt Symbol Detected */ #define QPR_PREEM 0x0020 /* Two Idle Symbols together */ #define QPR_ACOMP 0x0010 /* Autonegotiation complete */ #define QPR_JABBER 0x0004 /* Jabber detected */ #define QPR_RFAULT 0x0002 /* Remote Fault */ #define QPR_LINK 0x0001 /* Link */ #define MII_ICSPHY_TTR 0x12 /* 10baseT Operations Register */ #define TTR_RJABBER 0x8000 /* Remote Jabber */ #define TTR_POLARITY 0x4000 /* Polarity Reversed */ #define TTR_NOJABBER 0x0020 /* Disable Jabber Check */ #define TTR_LOOP 0x0010 /* Loopback mode */ #define TTR_NOAPOLARITY 0x0008 /* Disable auto polarity correction */ #define TTR_NOSQE 0x0004 /* Disable SQE check */ #define TTR_NOLINK 0x0002 /* Disable Link check */ #define TTR_NOSQUELCH 0x0001 /* Disable squelch */ #define MII_ICSPHY_ECR2 0x13 /* Extended Control Register 2 */ #define ECR2_REPEATER 0x8000 /* Repeater Mode */ #define ECR2_HWSW 0x4000 /* hw/sw config priority */ #define ECR2_LPRF 0x2000 /* link partner supports rem fault */ #define ECR2_FORCERF 0x0400 /* Force transmit of rem fault */ #define ECR2_RFPUP 0x0010 /* Rem fault on power up */ #define ECR2_Q10T 0x0004 /* Qualified 10baseT data */ #define ECR2_10TPROT 0x0002 /* 10baseT protect */ #define ECR2_AUTOPWRDN 0x0001 /* automatic power down */ #endif /* _DEV_MII_ICSPHYREG_H_ */
