/* $NetBSD: gemreg.h,v 1.16 2021/08/17 22:00:31 andvar Exp $ */ /* * * Copyright (C) 2001 Eduardo Horvath. * All rights reserved. * * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * */ #ifndef _IF_GEMREG_H #define _IF_GEMREG_H /* * Register definitions for Sun GEM Gigabit Ethernet * See `GEM Gigabit Ethernet ASIC Specification' * http://www.sun.com/processors/manuals/ge.pdf * and `Sbus GEM Specification' * http://mediacast.sun.com/users/Barton808/media/gem_sbus-1.pdf * section 3.1.3 GEM Register Space */ /* * Global Resources * Section 3.1.4.1 * * First bank: this registers live at the start of the PCI * mapping, and at the start of the second bank of the SBus * version. */ #define GEM_SEB_STATE 0x0000 /* SEB State (R/O) */ #define GEM_CONFIG 0x0004 /* Configuration */ #define GEM_STATUS 0x000c /* Status */ /* Note: Reading the status register auto-clears bits 0-6 */ #define GEM_INTMASK 0x0010 /* Interrupt Mask */ #define GEM_INTACK 0x0014 /* Interrupt Acknowledge (W/O) */ #define GEM_STATUS_ALIAS 0x001c /* Status Alias */ /* This is the same as GEM_STATUS but reading it does not auto-clear bits. */ /* * Second bank: this registers live at offset 0x1000 of the PCI * mapping, and at the start of the first bank of the SBus * version. */ #define GEM_PCI_BANK2_OFFSET 0x1000 #define GEM_PCI_BANK2_SIZE 0x14 #define GEM_ERROR_STATUS 0x0000 /* PCI Error Status */ #define GEM_ERROR_MASK 0x0004 /* PCI Error Mask */ #define GEM_BIF_CONFIG 0x0008 /* PCI BIF Configuration */ #define GEM_BIF_DIAG 0x000c /* PCI BIF Diagnostic */ #define GEM_RESET 0x0010 /* PCI Software Reset */ #define GEM_SBUS_RESET 0x0000 /* SBus Reset */ #define GEM_SBUS_CONFIG 0x0004 /* SBus Burst-Size Configuration */ #define GEM_SBUS_ERROR_STATUS 0x0008 /* SBus Fatal Error */ #define GEM_SBUS_REVISION 0x000c /* SBus Revision */ /* SBus Software Reset at same offset (0x0010) as PCI Software Reset above */ /* * Bits in GEM_SEB_STATE register * For diagnostic use */ #define GEM_SEB_ARB 0x000000002 /* Arbitration status */ #define GEM_SEB_RXWON 0x000000004 /* * Bits in GEM_CONFIG register * Default: 0x00042 */ #define GEM_CONFIG_BURST_64 0x000000000 /* 0->infinity, 1->64KB */ #define GEM_CONFIG_BURST_INF 0x000000001 /* 0->infinity, 1->64KB */ #define GEM_CONFIG_TXDMA_LIMIT 0x00000003e #define GEM_CONFIG_RXDMA_LIMIT 0x0000007c0 /* GEM_CONFIG_RONPAULBIT and GEM_CONFIG_BUG2FIX are Apple only. */ #define GEM_CONFIG_RONPAULBIT 0x000000800 /* after infinite burst use * memory read multiple for * PCI commands */ #define GEM_CONFIG_BUG2FIX 0x000001000 /* fix RX hang after overflow */ #define GEM_CONFIG_TXDMA_LIMIT_SHIFT 1 #define GEM_CONFIG_RXDMA_LIMIT_SHIFT 6 /* * Interrupt bits, for both the GEM_STATUS and GEM_INTMASK regs. * Bits 0-6 auto-clear when read. */ #define GEM_INTR_TX_INTME 0x000000001 /* Frame w/INTME bit set sent */ #define GEM_INTR_TX_EMPTY 0x000000002 /* TX ring empty */ #define GEM_INTR_TX_DONE 0x000000004 /* TX complete */ #define GEM_INTR_RX_DONE 0x000000010 /* Got a packet */ #define GEM_INTR_RX_NOBUF 0x000000020 /* No free receive buffers */ #define GEM_INTR_RX_TAG_ERR 0x000000040 /* RX Tag framing error */ #define GEM_INTR_PERR 0x000000080 /* Parity error */ #define GEM_INTR_PCS 0x000002000 /* PCS interrupt */ #define GEM_INTR_TX_MAC 0x000004000 /* TX MAC interrupt */ #define GEM_INTR_RX_MAC 0x000008000 /* RX MAC interrupt */ #define GEM_INTR_MAC_CONTROL 0x000010000 /* MAC control interrupt */ #define GEM_INTR_MIF 0x000020000 /* MIF interrupt */ #define GEM_INTR_BERR 0x000040000 /* Bus error interrupt */ #define GEM_INTR_BITS "\177\020" \ "b\0INTME\0b\1TXEMPTY\0b\2TXDONE\0" \ "b\4RXDONE\0b\5RXNOBUF\0b\6RX_TAG_ERR\0" \ "b\xdPCS\0b\xeTXMAC\0b\xfRXMAC\0" \ "b\x10MAC_CONTROL\0b\x11MIF\0b\x12IBERR\0\0" /* Top part (bits 19-31) of GEM_STATUS has TX completion information */ #define GEM_STATUS_TX_COMPL 0xfff800000 /* TX completion reg. */ /* * Bits in GEM_ERROR_STATUS and GEM_ERROR_MASK PCI registers */ #define GEM_ERROR_STAT_BADACK 0x000000001 /* No ACK64# */ #define GEM_ERROR_STAT_DTRTO 0x000000002 /* Delayed xaction timeout */ #define GEM_ERROR_STAT_OTHERS 0x000000004 /* Other PCI errors. Read PCI Status Register in PCI Configuration space */ #define GEM_ERROR_BITS "\177\020b\0ACKBAD\0b\1DTRTO\0b\2OTHER\0\0" /* * Bits in GEM_SBUS_CONFIG register */ #define GEM_SBUS_CFG_BSIZE32 0x00000001 #define GEM_SBUS_CFG_BSIZE64 0x00000002 #define GEM_SBUS_CFG_BSIZE128 0x00000004 #define GEM_SBUS_CFG_BMODE64 0x00000008 #define GEM_SBUS_CFG_PARITY 0x00000200 /* * Bits in GEM_BIF_CONFIG register * Default: 0x0 */ #define GEM_BIF_CONFIG_SLOWCLK 0x000000001 /* Parity error timing */ #define GEM_BIF_CONFIG_HOST_64 0x000000002 /* 64-bit host */ #define GEM_BIF_CONFIG_B64D_DIS 0x000000004 /* no 64-bit data cycle */ #define GEM_BIF_CONFIG_M66EN 0x000000008 #define GEM_BIF_CONFIG_BITS "\177\020b\0SLOWCLK\0b\1HOST64\0" \ "b\2B64DIS\0b\3M66EN\0\0" /* * Bits in GEM_BIF_DIAG register * Default: 0x00000000 */ #define GEN_BIF_DIAG_PCIBURST 0x007f0000 /* PCI Burst Controller state * machine */ #define GEN_BIF_DIAG_STATE 0xff000000 /* BIF state machine */ /* * Bits in GEM_RESET register * RESET_TX and RESET_RX self clear when complete. */ #define GEM_RESET_TX 0x000000001 /* Reset TX half */ #define GEM_RESET_RX 0x000000002 /* Reset RX half */ #define GEM_RESET_GLOBAL 0x000000003 /* Global Reset */ #define GEM_RESET_RSTOUT 0x000000004 /* Force PCI RSTOUT# */ /* * TX DMA Programmable Resources * Section 3.1.4.2 * The 53 most significant bits of the Descriptor Base Low/High registers * are used as the TX descriptor ring base address. The ring base must be * initialized to a 2KByte-aligned address after power-on or software reset. */ #define GEM_TX_KICK 0x2000 /* TX Kick */ /* Note: Write last valid desc + 1 */ #define GEM_TX_CONFIG 0x2004 /* TX Configuration */ #define GEM_TX_RING_PTR_LO 0x2008 /* TX Descriptor Base Low */ #define GEM_TX_RING_PTR_HI 0x200c /* TX Descriptor Base High */ /* 0x2010 Reserved */ #define GEM_TX_FIFO_WR_PTR 0x2014 /* TX FIFO Write Pointer */ #define GEM_TX_FIFO_SDWR_PTR 0x2018 /* TX FIFO Shadow Write Ptr */ #define GEM_TX_FIFO_RD_PTR 0x201c /* TX FIFO Read Pointer */ #define GEM_TX_FIFO_SDRD_PTR 0x2020 /* TX FIFO Shadow Read Ptr */ #define GEM_TX_FIFO_PKT_CNT 0x2024 /* TX FIFO Packet Counter */ #define GEM_TX_STATE_MACHINE 0x2028 /* TX State Machine */ /* 0x202c Unknown */ #define GEM_TX_DATA_PTR_LO 0x2030 /* TX Data Pointer Low */ #define GEM_TX_DATA_PTR_HI 0x2034 /* TX Data Pointer High */ #define GEM_TX_COMPLETION 0x2100 /* TX Completion */ #define GEM_TX_FIFO_ADDRESS 0x2104 /* TX FIFO Address */ #define GEM_TX_FIFO_TAG 0x2108 /* TX FIFO Tag */ #define GEM_TX_FIFO_DATA_LO 0x210c /* TX FIFO Data Low */ #define GEM_TX_FIFO_DATA_HI_T1 0x2110 /* TX FIFO Data HighT1 */ #define GEM_TX_FIFO_DATA_HI_T0 0x2114 /* TX FIFO Data HighT0 */ #define GEM_TX_FIFO_SIZE 0x2118 /* TX FIFO Size */ #define GEM_TX_DEBUG 0x3028 /* * Bits in GEM_TX_CONFIG register * Default: 0x118c10 * TX FIFO Threshold should be set to 0x4ff */ #define GEM_TX_CONFIG_TXDMA_EN 0x00000001 /* TX DMA enable */ #define GEM_TX_CONFIG_TXRING_SZ 0x0000001e /* TX ring size */ #define GEM_TX_CONFIG_TXFIFO_SL 0x00000020 /* TX DMA FIFO PIO select */ #define GEM_TX_CONFIG_TXFIFO_TH 0x001ffc00 /* TX fifo threshold */ #define GEM_TX_CONFIG_PACED 0x00200000 /* TX_all_int modifier */ #define GEM_RING_SZ_32 (0<<1) /* 32 descriptors */ #define GEM_RING_SZ_64 (1<<1) #define GEM_RING_SZ_128 (2<<1) #define GEM_RING_SZ_256 (3<<1) #define GEM_RING_SZ_512 (4<<1) #define GEM_RING_SZ_1024 (5<<1) #define GEM_RING_SZ_2048 (6<<1) #define GEM_RING_SZ_4096 (7<<1) #define GEM_RING_SZ_8192 (8<<1) /* Default */ /* * Bits in GEM_TX_COMPLETION register */ #define GEM_TX_COMPLETION_MASK 0x00001fff /* # of last descriptor */ /* * RX DMA Programmable Resources * Section 3.1.4.3 * The 53 most significant bits of the Descriptor Base Low/High registers * are used as the RX descriptor ring base address. The ring base must be * initialized to a 2KByte-aligned address after power-on or software reset. */ #define GEM_RX_CONFIG 0x4000 /* RX Configuration */ #define GEM_RX_RING_PTR_LO 0x4004 /* RX Descriptor Base Low */ #define GEM_RX_RING_PTR_HI 0x4008 /* RX Descriptor Base High */ #define GEM_RX_FIFO_WR_PTR 0x400c /* RX FIFO Write Pointer */ #define GEM_RX_FIFO_SDWR_PTR 0x4010 /* RX FIFO Shadow Write Ptr */ #define GEM_RX_FIFO_RD_PTR 0x4014 /* RX FIFO Read Pointer */ #define GEM_RX_FIFO_PKT_CNT 0x4018 /* RX FIFO Packet Counter */ #define GEM_RX_STATE_MACHINE 0x401c /* RX State Machine */ #define GEM_RX_PAUSE_THRESH 0x4020 /* Pause Thresholds */ #define GEM_RX_DATA_PTR_LO 0x4024 /* RX Data Pointer Low */ #define GEM_RX_DATA_PTR_HI 0x4028 /* RX Data Pointer High */ #define GEM_RX_KICK 0x4100 /* RX Kick */ /* Note: Write last valid desc + 1. Must be a multiple of 4 */ #define GEM_RX_COMPLETION 0x4104 /* RX Completion */ #define GEM_RX_BLANKING 0x4108 /* RX Blanking */ #define GEM_RX_FIFO_ADDRESS 0x410c /* RX FIFO Address */ #define GEM_RX_FIFO_TAG 0x4110 /* RX FIFO Tag */ #define GEM_RX_FIFO_DATA_LO 0x4114 /* RX FIFO Data Low */ #define GEM_RX_FIFO_DATA_HI_T1 0x4118 /* RX FIFO Data HighT0 */ #define GEM_RX_FIFO_DATA_HI_T0 0x411c /* RX FIFO Data HighT1 */ #define GEM_RX_FIFO_SIZE 0x4120 /* RX FIFO Size */ /* * Bits in GEM_RX_CONFIG register * Default: 0x1000010 */ #define GEM_RX_CONFIG_RXDMA_EN 0x00000001 /* RX DMA enable */ #define GEM_RX_CONFIG_RXRING_SZ 0x0000001e /* RX ring size */ #define GEM_RX_CONFIG_BATCH_DIS 0x00000020 /* desc batching disable */ #define GEM_RX_CONFIG_FBOFF 0x00001c00 /* first byte offset */ #define GEM_RX_CONFIG_CXM_START 0x000fe000 /* cksum start offset bytes */ #define GEM_RX_CONFIG_FIFO_THRS 0x07000000 /* fifo threshold size */ #define GEM_THRSH_64 0 #define GEM_THRSH_128 1 #define GEM_THRSH_256 2 #define GEM_THRSH_512 3 #define GEM_THRSH_1024 4 #define GEM_THRSH_2048 5 #define GEM_RX_CONFIG_FIFO_THRS_SHIFT 24 #define GEM_RX_CONFIG_FBOFF_SHFT 10 #define GEM_RX_CONFIG_CXM_START_SHFT 13 /* GEM_RX_PAUSE_THRESH register bits -- sizes in multiples of 64 bytes */ #define GEM_RX_PTH_XOFF_THRESH 0x000001ff #define GEM_RX_PTH_XON_THRESH 0x001ff000 /* GEM_RX_BLANKING register bits */ #define GEM_RX_BLANKING_PACKETS 0x000001ff /* Delay intr for x packets */ #define GEM_RX_BLANKING_TIME 0x000ff000 /* Delay intr for x ticks */ #define GEM_RX_BLANKING_TIME_SHIFT 12 /* One tick is 2048 PCI clocks, or 16us at 66MHz */ /* * MAC Programmable Resources * Section 3.1.5 */ #define GEM_MAC_TXRESET 0x6000 /* TX MAC Software Reset Cmd */ #define GEM_MAC_RXRESET 0x6004 /* RX MAC Software Reset Cmd */ /* Note: Store 1, cleared when done for TXRESET and RXRESET */ #define GEM_MAC_SEND_PAUSE_CMD 0x6008 /* Send Pause Command */ #define GEM_MAC_TX_STATUS 0x6010 /* TX MAC Status */ #define GEM_MAC_RX_STATUS 0x6014 /* RX MAC Status */ #define GEM_MAC_CONTROL_STATUS 0x6018 /* MAC Control Status */ #define GEM_MAC_TX_MASK 0x6020 /* TX MAC Mask */ #define GEM_MAC_RX_MASK 0x6024 /* RX MAC Mask */ #define GEM_MAC_CONTROL_MASK 0x6028 /* MAC Control Mask */ #define GEM_MAC_TX_CONFIG 0x6030 /* TX MAC Configuration */ #define GEM_MAC_RX_CONFIG 0x6034 /* XX MAC Configuration */ #define GEM_MAC_CONTROL_CONFIG 0x6038 /* MAC Control Configuration */ #define GEM_MAC_XIF_CONFIG 0x603c /* XIF Configuration */ #define GEM_MAC_IPG0 0x6040 /* InterPacketGap0 */ #define GEM_MAC_IPG1 0x6044 /* InterPacketGap1 */ #define GEM_MAC_IPG2 0x6048 /* InterPacketGap2 */ #define GEM_MAC_SLOT_TIME 0x604c /* SlotTime, bits 0-7 */ #define GEM_MAC_MAC_MIN_FRAME 0x6050 /* MinFrameSize */ #define GEM_MAC_MAC_MAX_FRAME 0x6054 /* MaxFrameSize */ #define GEM_MAC_PREAMBLE_LEN 0x6058 /* PA Size */ #define GEM_MAC_JAM_SIZE 0x605c /* JamSize */ #define GEM_MAC_ATTEMPT_LIMIT 0x6060 /* Attempt Limit */ #define GEM_MAC_CONTROL_TYPE 0x6064 /* MAC Control Type */ #define GEM_MAC_ADDR0 0x6080 /* Normal MAC address 0 */ #define GEM_MAC_ADDR1 0x6084 #define GEM_MAC_ADDR2 0x6088 #define GEM_MAC_ADDR3 0x608c /* Alternate MAC address 0 */ #define GEM_MAC_ADDR4 0x6090 #define GEM_MAC_ADDR5 0x6094 #define GEM_MAC_ADDR6 0x6098 /* Control MAC address 0 */ #define GEM_MAC_ADDR7 0x609c #define GEM_MAC_ADDR8 0x60a0 #define GEM_MAC_ADDR_FILTER0 0x60a4 /* Address Filter */ #define GEM_MAC_ADDR_FILTER1 0x60a8 #define GEM_MAC_ADDR_FILTER2 0x60ac #define GEM_MAC_ADR_FLT_MASK1_2 0x60b0 /* Address Filter Mask 2&1 */ #define GEM_MAC_ADR_FLT_MASK0 0x60b4 /* Address Filter Mask 0 */ #define GEM_MAC_HASH0 0x60c0 /* Hash table 0 */ #define GEM_MAC_HASH1 0x60c4 #define GEM_MAC_HASH2 0x60c8 #define GEM_MAC_HASH3 0x60cc #define GEM_MAC_HASH4 0x60d0 #define GEM_MAC_HASH5 0x60d4 #define GEM_MAC_HASH6 0x60d8 #define GEM_MAC_HASH7 0x60dc #define GEM_MAC_HASH8 0x60e0 #define GEM_MAC_HASH9 0x60e4 #define GEM_MAC_HASH10 0x60e8 #define GEM_MAC_HASH11 0x60ec #define GEM_MAC_HASH12 0x60f0 #define GEM_MAC_HASH13 0x60f4 #define GEM_MAC_HASH14 0x60f8 #define GEM_MAC_HASH15 0x60fc #define GEM_MAC_NORM_COLL_CNT 0x6100 /* Normal Collision Counter */ #define GEM_MAC_FIRST_COLL_CNT 0x6104 /* First Attempt Successful Collision Counter */ #define GEM_MAC_EXCESS_COLL_CNT 0x6108 /* Excess Collision Counter */ #define GEM_MAC_LATE_COLL_CNT 0x610c /* Late Collision Counter */ #define GEM_MAC_DEFER_TMR_CNT 0x6110 /* Defer Timer */ #define GEM_MAC_PEAK_ATTEMPTS 0x6114 /* Peak Attempts */ #define GEM_MAC_RX_FRAME_COUNT 0x6118 /* Receive Frame Counter */ #define GEM_MAC_RX_LEN_ERR_CNT 0x611c /* Length Error Counter */ #define GEM_MAC_RX_ALIGN_ERR 0x6120 /* Alignment Error Counter */ #define GEM_MAC_RX_CRC_ERR_CNT 0x6124 /* FCS Error Counter */ #define GEM_MAC_RX_CODE_VIOL 0x6128 /* RX Code Violation Error Counter */ #define GEM_MAC_RANDOM_SEED 0x6130 /* Random Number Seed */ #define GEM_MAC_MAC_STATE 0x6134 /* State Machine */ /* * Bits in GEM_MAC_SEND_PAUSE_CMD register * Pause time is in units of Slot Times. */ #define GEM_MAC_PAUSE_CMD_TIME 0x0000ffff #define GEM_MAC_PAUSE_CMD_SEND 0x00010000 /* * Bits in GEM_MAC_TX_STATUS and _MASK register * Interrupt bits are auto-cleared when the status register is read and * the corresponding bit is set in the mask register. */ #define GEM_MAC_TX_XMIT_DONE 0x00000001 /* Successful transmission */ #define GEM_MAC_TX_UNDERRUN 0x00000002 /* TX "data starvation" */ #define GEM_MAC_TX_PKT_TOO_LONG 0x00000004 /* Frame exceeds max. length */ #define GEM_MAC_TX_NCC_EXP 0x00000008 /* Normal collision counter has rolled over */ #define GEM_MAC_TX_ECC_EXP 0x00000010 /* Excessive coll cnt rolled */ #define GEM_MAC_TX_LCC_EXP 0x00000020 /* Late coll cnt rolled */ #define GEM_MAC_TX_FCC_EXP 0x00000040 /* First coll cnt rolled */ #define GEM_MAC_TX_DEFER_EXP 0x00000080 /* Defer timer cnt rolled */ #define GEM_MAC_TX_PEAK_EXP 0x00000100 /* Peak attempts cnt rolled */ /* * Bits in GEM_MAC_RX_STATUS and _MASK register */ #define GEM_MAC_RX_DONE 0x00000001 /* Successful reception */ #define GEM_MAC_RX_OVERFLOW 0x00000002 /* RX resource lack */ #define GEM_MAC_RX_FRAME_CNT 0x00000004 /* Receive frame counter has rolled over */ #define GEM_MAC_RX_ALIGN_EXP 0x00000008 /* Alignment error cnt rolled */ #define GEM_MAC_RX_CRC_EXP 0x00000010 /* CRC error cnt rolled */ #define GEM_MAC_RX_LEN_EXP 0x00000020 /* Length error cnt rolled */ #define GEM_MAC_RX_CVI_EXP 0x00000040 /* Code violation err rolled */ /* * Bits in GEM_MAC_CONTROL_STATUS and GEM_MAC_CONTROL_MASK register */ #define GEM_MAC_PAUSED 0x00000001 /* Pause received */ #define GEM_MAC_PAUSE 0x00000002 /* enter pause state */ #define GEM_MAC_RESUME 0x00000004 /* exit pause state */ #define GEM_MAC_PAUSE_TIME 0xffff0000 /* Pause time received */ #define GEM_MAC_STATUS_BITS "\177\020b\0PAUSED\0b\1PAUSE\0b\2RESUME\0\0" /* * Bits in GEM_MAC_XIF_CONFIG register * Default: 0x00 */ #define GEM_MAC_XIF_TX_MII_ENA 0x00000001 /* Enable MII output */ #define GEM_MAC_XIF_MII_LOOPBK 0x00000002 /* Enable (G)MII loopback */ #define GEM_MAC_XIF_ECHO_DISABL 0x00000004 /* Disable echo */ #define GEM_MAC_XIF_GMII_MODE 0x00000008 /* Select GMII/MII mode */ #define GEM_MAC_XIF_MII_BUF_ENA 0x00000010 /* Enable MII recv buffers */ #define GEM_MAC_XIF_LINK_LED 0x00000020 /* force link LED active */ #define GEM_MAC_XIF_FDPLX_LED 0x00000040 /* force FDPLX LED active */ #define GEM_MAC_XIF_BITS "\177\020b\0TXMIIENA\0b\1MIILOOP\0b\2NOECHO" \ "\0b\3GMII\0b\4MIIBUFENA\0b\5LINKLED\0" \ "b\6FDLED\0\0" /* * Bits in GEM_MAC_TX_CONFIG register * GEM_MAC_TX_ENABLE must be cleared and a delay imposed before writing to * other bits in this register or any of the MAC parameters registers. * The GEM_MAC_TX_ENABLE bit will read 0 when the transmitter has stopped. * Carrier Extension must be set when operating in Half-Duplex at 1Gbps, * and disabled otherwise. To enable this GEM_MAC_TX_CARR_EXTEND and * GEM_MAC_RX_CARR_EXTEND must be set to 1 and the Slot Time register must * be set to 0x200. */ #define GEM_MAC_TX_ENABLE 0x00000001 /* TX enable */ #define GEM_MAC_TX_IGN_CARRIER 0x00000002 /* Ignore carrier sense */ #define GEM_MAC_TX_IGN_COLLIS 0x00000004 /* ignore collisions */ #define GEM_MAC_TX_ENA_IPG0 0x00000008 /* extend Rx-to-TX IPG */ #define GEM_MAC_TX_NGU 0x00000010 /* Never give up */ #define GEM_MAC_TX_NGU_LIMIT 0x00000020 /* Never give up limit */ #define GEM_MAC_TX_NO_BACKOFF 0x00000040 /* Never backoff on coll */ #define GEM_MAC_TX_SLOWDOWN 0x00000080 /* Watch carrier sense */ #define GEM_MAC_TX_NO_FCS 0x00000100 /* no FCS will be generated */ #define GEM_MAC_TX_CARR_EXTEND 0x00000200 /* Ena TX Carrier Extension */ #define GEM_MAC_TX_CONFIG_BITS "\177\020" \ "b\0TXENA\0b\1IGNCAR\0b\2IGNCOLLIS\0" \ "b\3IPG0ENA\0b\4TXNGU\0b\5TXNGULIM\0" \ "b\6NOBKOFF\0b\7SLOWDN\0b\x8NOFCS\0" \ "b\x9TXCARREXT\0\0" /* * Bits in GEM_MAC_RX_CONFIG register * The GEM_MAC_RX_ENABLE bit must be cleared and a delay of 3.2ms imposed * before writing to other bits in this register or any of the MAC * parameters registers. The GEM_MAC_RX_ENABLE bit will read 0 when the * receiver has stopped. * The GEM_MAC_RX_HASH_FILTER bit must be cleared and a delay of 3.2ms * imposed before writing to any of the Hash Table registers. The * GEM_MAC_RX_HASH_FILTER bit will read 0 when the registers may be written. * The GEM_MAC_RX_ADDR_FILTER bit must be cleared and a delay of 3.2ms * imposed before writing to any of the Address Filter registers. The * GEM_MAC_RX_ADDR_FILTER bit will read 0 when the registers may be written. * See "Carrier Extension" above. */ #define GEM_MAC_RX_ENABLE 0x00000001 /* RX enable */ #define GEM_MAC_RX_STRIP_PAD 0x00000002 /* strip pad bytes */ #define GEM_MAC_RX_STRIP_CRC 0x00000004 #define GEM_MAC_RX_PROMISCUOUS 0x00000008 /* promiscuous mode */ #define GEM_MAC_RX_PROMISC_GRP 0x00000010 /* promiscuous group mode */ #define GEM_MAC_RX_HASH_FILTER 0x00000020 /* enable hash filter */ #define GEM_MAC_RX_ADDR_FILTER 0x00000040 /* enable address filter */ #define GEM_MAC_RX_ERRCHK_DIS 0x00000080 /* disable error discard */ #define GEM_MAC_RX_CARR_EXTEND 0x00000100 /* Ena RX Carrier Extension */ #define GEM_MAC_RX_CONFIG_BITS "\177\020" \ "b\0RXENA\0b\1STRPAD\0b\2STRCRC\0" \ "b\3PROMIS\0b\4PROMISCGRP\0b\5HASHFLTR\0" \ "b\6ADDRFLTR\0b\7ERRCHKDIS\0b\x9TXCARREXT\0\0" /* * Bits in GEM_MAC_CONTROL_CONFIG * Default; 0x0 */ #define GEM_MAC_CC_TX_PAUSE 0x00000001 /* send pause enabled */ #define GEM_MAC_CC_RX_PAUSE 0x00000002 /* receive pause enabled */ #define GEM_MAC_CC_PASS_PAUSE 0x00000004 /* pass pause up */ #define GEM_MAC_CC_BITS "\177\020b\0TXPAUSE\0b\1RXPAUSE\0b\2NOPAUSE\0\0" /* GEM_MAC_MAC_STATE register bits */ #define GEM_MAC_STATE_OVERFLOW 0x03800000 /* * Bits in GEM_MAC_SLOT_TIME register * The slot time is used as PAUSE time unit, value depends on whether carrier * extension is enabled. */ #define GEM_MAC_SLOT_TIME_CARR_EXTEND 0x200 #define GEM_MAC_SLOT_TIME_NORMAL 0x40 /* * Recommended values for MAC registers: * GEM_MAC_IPG0 0x00 * GEM_MAC_IPG1 0x08 * GEM_MAC_IPG2 0x04 * GEM_MAC_SLOT_TIME 0x40 (see "Carrier Extension" above) * Bits in GEM_MAC_MAC_MAX_FRAME register * max burst size 0x7fff0000 * max frame size 0x00007fff * GEM_MAC_MAC_MIN_FRAME 0x40 * GEM_MAC_MAC_MAX_FRAME 0x200005ee * GEM_MAC_PREAMBLE_LEN 0x07 (minimum of 0x02) * GEM_MAC_JAM_SIZE 0x04 * GEM_MAC_ATTEMPT_LIMIT 0x10 * GEM_MAC_CONTROL_TYPE 0x8808 */ /* * Address detection and filtering registers (16-bit unless noted): * GEM_MAC_ADDR0 normal priority MAC address bits 32-47 * GEM_MAC_ADDR1 normal priority MAC address bits 16-31 * GEM_MAC_ADDR2 normal priority MAC address bits 0-15 * GEM_MAC_ADDR3 alternate MAC address bits 32-47 * GEM_MAC_ADDR4 alternate MAC address bits 16-31 * GEM_MAC_ADDR5 alternate MAC address bits 0-15 * GEM_MAC_ADDR6 MAC control address bits 32-47 * GEM_MAC_ADDR7 MAC control address bits 16-31 * GEM_MAC_ADDR8 MAC control address bits 0-15 * GEM_MAC_ADDR_FILTER0 address filter bits 32-47 * GEM_MAC_ADDR_FILTER1 address filter bits 16-31 * GEM_MAC_ADDR_FILTER2 address filter bits 0-15 * GEM_MAC_ADR_FLT_MASK1_2 mask for GEM_MAC_ADDR_FILTER1 and 2 (8-bit) * GEM_MAC_ADR_FLT_MASK0 mask for GEM_MAC_ADDR_FILTER0 * GEM_MAC_HASH0 hash table bits 240-255 * GEM_MAC_HASH1 hash table bits 224-239 * GEM_MAC_HASH2 hash table bits 208-223 * GEM_MAC_HASH3 hash table bits 192-207 * GEM_MAC_HASH4 hash table bits 176-191 * GEM_MAC_HASH5 hash table bits 160-175 * GEM_MAC_HASH6 hash table bits 144-159 * GEM_MAC_HASH7 hash table bits 128-143 * GEM_MAC_HASH8 hash table bits 112-127 * GEM_MAC_HASH9 hash table bits 96-111 * GEM_MAC_HASH10 hash table bits 80-95 * GEM_MAC_HASH11 hash table bits 64-79 * GEM_MAC_HASH12 hash table bits 48-63 * GEM_MAC_HASH13 hash table bits 32-47 * GEM_MAC_HASH14 hash table bits 16-31 * GEM_MAC_HASH15 hash table bits 0-15 */ /* * Recommended values for statistic registers: * GEM_MAC_NORM_COLL_CNT 0x0000 * GEM_MAC_FIRST_COLL_CNT 0x0000 * GEM_MAC_EXCESS_COLL_CNT 0x0000 * GEM_MAC_LATE_COLL_CNT 0x0000 * GEM_MAC_DEFER_TMR_CNT 0x0000 * GEM_MAC_PEAK_ATTEMPTS 0x0000 * GEM_MAC_RX_FRAME_COUNT 0x0000 * GEM_MAC_RX_LEN_ERR_CNT 0x0000 * GEM_MAC_RX_ALIGN_ERR 0x0000 * GEM_MAC_RX_CRC_ERR_CNT 0x0000 * GEM_MAC_RX_CODE_VIOL 0x0000 */ /* * MIF Programmable Resources * Section 3.1.5.8 * Bit-bang registers use low bit only */ #define GEM_MIF_BB_CLOCK 0x6200 /* MIF Bit-Bang Clock */ #define GEM_MIF_BB_DATA 0x6204 /* MIF Bit-Bang Data */ #define GEM_MIF_BB_OUTPUT_ENAB 0x6208 /* MIF Bit-Bang Output Enable */ #define GEM_MIF_FRAME 0x620c /* MIF Frame/Output */ #define GEM_MIF_CONFIG 0x6210 /* MIF Configuration */ #define GEM_MIF_INTERRUPT_MASK 0x6214 /* MIF Mask */ #define GEM_MIF_BASIC_STATUS 0x6218 /* MIF Status */ #define GEM_MIF_STATE_MACHINE 0x621c /* MIF State Machine */ /* * Bits in GEM_MIF_FRAME register */ #define GEM_MIF_FRAME_DATA 0x0000ffff /* Instruction payload */ #define GEM_MIF_FRAME_TA0 0x00010000 /* TA bit, 1 for completion */ #define GEM_MIF_FRAME_TA1 0x00020000 /* TA bits */ #define GEM_MIF_FRAME_REG_ADDR 0x007c0000 /* Register address */ #define GEM_MIF_FRAME_PHY_ADDR 0x0f800000 /* PHY address, should be 0 */ #define GEM_MIF_FRAME_OP 0x30000000 /* operation - write/read */ #define GEM_MIF_FRAME_START 0xc0000000 /* START bits */ #define GEM_MIF_FRAME_READ 0x60020000 #define GEM_MIF_FRAME_WRITE 0x50020000 #define GEM_MIF_REG_SHIFT 18 #define GEM_MIF_PHY_SHIFT 23 /* * Bits in GEM_MIF_CONFIG register */ #define GEM_MIF_CONFIG_PHY_SEL 0x00000001 /* PHY select, 0=MDIO_0 */ #define GEM_MIF_CONFIG_POLL_ENA 0x00000002 /* poll enable */ #define GEM_MIF_CONFIG_BB_ENA 0x00000004 /* bit bang enable */ #define GEM_MIF_CONFIG_REG_ADR 0x000000f8 /* poll register address */ #define GEM_MIF_CONFIG_MDI0 0x00000100 /* MDIO_0 B-B data/attached */ #define GEM_MIF_CONFIG_MDI1 0x00000200 /* MDIO_1 B-B data/attached */ #define GEM_MIF_CONFIG_PHY_ADR 0x00007c00 /* poll PHY address */ /* MDIO_0 is onboard transceiver MDIO_1 is external, PHY addr for both is 0 */ #define GEM_MIF_CONFIG_BITS "\177\020b\0PHYSEL\0b\1POLL\0b\2BBENA\0" \ "b\x8MDIO0\0b\x9MDIO1\0\0" /* * Bits in GEM_MIF_BASIC_STATUS and GEM_MIF_INTERRUPT_MASK * The Basic part is the last value read in the POLL field of the config * register. * The status part indicates the bits that have changed. */ #define GEM_MIF_STATUS 0x0000ffff #define GEM_MIF_BASIC 0xffff0000 /* * PCS/Serialink Registers * Section 3.1.6 * DO NOT TOUCH THESE REGISTERS ON ERI -- IT HARD HANGS. */ #define GEM_MII_CONTROL 0x9000 /* PCS MII Control */ #define GEM_MII_STATUS 0x9004 /* PCS MII Status */ #define GEM_MII_ANAR 0x9008 /* PCS MII Advertisement */ #define GEM_MII_ANLPAR 0x900c /* PCS MII Link Partner Ability */ #define GEM_MII_CONFIG 0x9010 /* PCS Configuration */ #define GEM_MII_STATE_MACHINE 0x9014 /* PCS State Machine */ #define GEM_MII_INTERRUP_STATUS 0x9018 /* PCS Interrupt Status */ #define GEM_MII_DATAPATH_MODE 0x9050 /* Datapath Mode Register */ #define GEM_MII_SLINK_CONTROL 0x9054 /* Serialink Control */ #define GEM_MII_OUTPUT_SELECT 0x9058 /* Share Output Select */ #define GEM_MII_SLINK_STATUS 0x905c /* Serialink Status */ /* * Bits in GEM_MII_CONTROL register * PCS "BMCR" (Basic Mode Control Reg) * Default: 0x1040 * AUTONEG and RESET self clear when relevant process is completed. */ #define GEM_MII_1GB_SPEED_SEL 0x00000040 /* 1000Mb/s, always 1 */ #define GEM_MII_CONTROL_COL_TST 0x00000080 /* collision test */ #define GEM_MII_CONTROL_FDUPLEX 0x00000100 /* full duplex, always 0 */ #define GEM_MII_CONTROL_RAN 0x00000200 /* restart auto negotiation */ #define GEM_MII_CONTROL_ISOLATE 0x00000400 /* isolate PHY, ignored */ #define GEM_MII_CONTROL_POWERDN 0x00000800 /* power down, ignored */ #define GEM_MII_CONTROL_AUTONEG 0x00001000 /* auto negotiation enabled */ #define GEM_MII_CONTROL_SPEED 0x00002000 /* speed select, ignored */ #define GEM_MII_CONTROL_LOOPBK 0x00004000 /* Serialink loopback */ #define GEM_MII_CONTROL_RESET 0x00008000 /* Reset PCS */ #define GEM_MII_CONTROL_BITS "\177\020b\7COLTST\0b\x8_FD\0b\x9RAN\0" \ "b\xaISOLATE\0b\xbPWRDWN\0b\xc_ANEG\0" \ "b\xdGIGE\0b\xeLOOP\0b\xfRESET\0\0" /* * Bits in GEM_MII_STATUS register. * PCS "BMSR" (Basic Mode Status Reg) * Default: 0x0108 */ #define GEM_MII_STATUS_EXTCAP 0x00000001 /* extended capability, always 0 */ #define GEM_MII_STATUS_JABBER 0x00000002 /* jabber detected, always 0 */ #define GEM_MII_STATUS_LINK_STS 0x00000004 /* link status, 1=up */ #define GEM_MII_STATUS_ACFG 0x00000008 /* can auto neg, always 1 */ #define GEM_MII_STATUS_REM_FLT 0x00000010 /* remote fault detected */ #define GEM_MII_STATUS_ANEG_CPT 0x00000020 /* auto negotiate complete */ #define GEM_MII_STATUS_EXT_STS 0x00000100 /* Is 1000Base-X, always 1 */ #define GEM_MII_STATUS_GB_HDX 0x00000200 /* can perform GBit HDX */ #define GEM_MII_STATUS_GB_FDX 0x00000400 /* can perform GBit FDX */ #define GEM_MII_STATUS_BITS "\177\020b\0EXTCAP\0b\1JABBER\0b\2LINKSTS\0" \ "b\3ACFG\0b\4REMFLT\0b\5ANEGCPT\0b\x9GBHDX\0" \ "b\xaGBFDX\0\0" /* * Bits in GEM_MII_ANAR and GEM_MII_ANLPAR registers * GEM_MII_ANAR contains our capabilities for auto- negotiation * (Default: 0x00e0) and GEM_MII_ANLPAR contains the link partners * abilities and is only valid after auto-negotiation completes. */ #define GEM_MII_ANEG_FUL_DUPLX 0x00000020 /* can do 1000Base-X FDX */ #define GEM_MII_ANEG_HLF_DUPLX 0x00000040 /* can do 1000Base-X HDX */ #define GEM_MII_ANEG_SYM_PAUSE 0x00000080 /* can do symmetric pause */ #define GEM_MII_ANEG_ASYM_PAUSE 0x00000100 /* can do asymmetric pause */ #define GEM_MII_ANEG_RF 0x00003000 /* advertise remote fault */ #define GEM_MII_ANEG_ACK 0x00004000 /* ack reception of Link Partner Capability */ #define GEM_MII_ANEG_NP 0x00008000 /* next page bit, always 0 */ #define GEM_MII_ANEG_BITS "\177\020b\5FDX\0b\6HDX\0b\7SYMPAUSE\0" \ "\b\x8_ASYMPAUSE\0\b\xdREMFLT\0\b\xeLPACK\0" \ "\b\xfNPBIT\0\0" /* * Bits in GEM_MII_CONFIG register * Default: 0x0 * GEM_MII_CONFIG_ENABLE must be 0 when modifiying the GEM_MII_ANAR * register. To isolate the MC from the media, set this bit to 0 and * restart auto-negotiation in GEM_MII_CONTROL. */ #define GEM_MII_CONFIG_ENABLE 0x00000001 /* Enable PCS */ #define GEM_MII_CONFIG_SDO 0x00000002 /* Signal Detect Override */ #define GEM_MII_CONFIG_SDL 0x00000004 /* Signal Detect active low */ #define GEM_MII_CONFIG_TIMER 0x0000000e /* link monitor timer values */ #define GEM_MII_CONFIG_JS 0x00000018 /* Jitter Study, 0 normal * 1 high freq, 2 low freq */ #define GEM_MII_CONFIG_ANTO 0x00000020 /* 10ms ANEG timer override */ #define GEM_MII_CONFIG_BITS "\177\020b\0PCSENA\0\0" /* * Bits in GEM_MII_STATE_MACHINE register * XXX These are best guesses from observed behavior. */ #define GEM_MII_FSM_STOP 0x00000000 /* stopped */ #define GEM_MII_FSM_RUN 0x00000001 /* running */ #define GEM_MII_FSM_UNKWN 0x00000100 /* unknown */ #define GEM_MII_FSM_DONE 0x00000101 /* complete */ /* * Bits in GEM_MII_INTERRUP_STATUS register * No mask register; mask with the global interrupt mask register. */ #define GEM_MII_INTERRUP_LINK 0x00000004 /* PCS link status change */ /* * Bits in GEM_MII_DATAPATH_MODE register * Default: none */ #define GEM_MII_DATAPATH_SERIAL 0x00000001 /* Use internal Serialink */ #define GEM_MII_DATAPATH_SERDES 0x00000002 /* Use PCS via 10bit interface */ #define GEM_MII_DATAPATH_MII 0x00000004 /* Use {G}MII, not PCS */ #define GEM_MII_DATAPATH_MIIOUT 0x00000008 /* Set serial output on GMII */ #define GEM_MII_DATAPATH_BITS "\177\020" \ "b\0SERIAL\0b\1SERDES\0b\2MII\0b\3MIIOUT\0\0" /* * Bits in GEM_MII_SLINK_CONTROL register * Default: 0x000 */ #define GEM_MII_SLINK_LOOPBACK 0x00000001 /* enable loopback on Serialink disable loopback on SERDES */ #define GEM_MII_SLINK_EN_SYNC_D 0x00000002 /* enable sync detection */ #define GEM_MII_SLINK_LOCK_REF 0x00000004 /* lock reference clock */ #define GEM_MII_SLINK_EMPHASIS 0x00000018 /* enable emphasis */ #define GEM_MII_SLINK_SELFTEST 0x000001c0 #define GEM_MII_SLINK_POWER_OFF 0x00000200 /* Power down Serialink block */ #define GEM_MII_SLINK_RX_ZERO 0x00000c00 /* PLL input to Serialink */ #define GEM_MII_SLINK_RX_POLL 0x00003000 /* PLL input to Serialink */ #define GEM_MII_SLINK_TX_ZERO 0x0000c000 /* PLL input to Serialink */ #define GEM_MII_SLINK_TX_POLL 0x00030000 /* PLL input to Serialink */ #define GEM_MII_SLINK_CONTROL_BITS \ "\177\020b\0LOOP\0b\1ENASYNC\0b\2LOCKREF" \ "\0b\3EMPHASIS1\0b\4EMPHASIS2\0b\x9PWRDWN\0\0" /* * Bits in GEM_MII_OUTPUT_SELECT register * Default: 0x0 */ #define GEM_MII_PROM_ADDR 0x00000003 /* Test output multiplexor */ /* * Bits in GEM_MII_SLINK_STATUS register * Default: 0x0 */ #define GEM_MII_SLINK_TEST 0x00000000 /* undergoing test */ #define GEM_MII_SLINK_LOCKED 0x00000001 /* waiting 500us lockrefn */ #define GEM_MII_SLINK_COMMA 0x00000002 /* waiting for comma detect */ #define GEM_MII_SLINK_SYNC 0x00000003 /* recv data synchronized */ /* * PCI Expansion ROM runtime access * Sun GEMs map a 1MB space for the PCI Expansion ROM as the second half * of the first register bank, although they only support up to 64KB ROMs. */ #define GEM_PCI_ROM_OFFSET 0x100000 #define GEM_PCI_ROM_SIZE 0x10000 /* Wired GEM PHY addresses */ #define GEM_PHYAD_INTERNAL 1 #define GEM_PHYAD_EXTERNAL 0 /* * GEM descriptor table structures. */ struct gem_desc { volatile uint64_t gd_flags; volatile uint64_t gd_addr; }; /* Transmit flags */ #define GEM_TD_BUFSIZE 0x0000000000007fffLL #define GEM_TD_CXSUM_START 0x00000000001f8000LL /* Cxsum start offset */ #define GEM_TD_CXSUM_STARTSHFT 15 #define GEM_TD_CXSUM_STUFF 0x000000001fe00000LL /* Cxsum stuff offset */ #define GEM_TD_CXSUM_STUFFSHFT 21 #define GEM_TD_CXSUM_ENABLE 0x0000000020000000LL /* Cxsum generation enable */ #define GEM_TD_END_OF_PACKET 0x0000000040000000LL #define GEM_TD_START_OF_PACKET 0x0000000080000000LL #define GEM_TD_INTERRUPT_ME 0x0000000100000000LL /* Interrupt me now */ #define GEM_TD_NO_CRC 0x0000000200000000LL /* do not insert crc */ /* * Only need to set GEM_TD_CXSUM_ENABLE, GEM_TD_CXSUM_STUFF, * GEM_TD_CXSUM_START, and GEM_TD_INTERRUPT_ME in 1st descriptor of a group. */ /* Receive flags */ #define GEM_RD_CHECKSUM 0x000000000000ffffLL /* is the complement */ #define GEM_RD_BUFSIZE 0x000000007fff0000LL #define GEM_RD_OWN 0x0000000080000000LL /* 1 - owned by h/w */ #define GEM_RD_HASHVAL 0x0ffff00000000000LL #define GEM_RD_HASH_PASS 0x1000000000000000LL /* passed hash filter */ #define GEM_RD_ALTERNATE_MAC 0x2000000000000000LL /* Alternate MAC adrs */ #define GEM_RD_BAD_CRC 0x4000000000000000LL #define GEM_RD_BUFSHIFT 16 #define GEM_RD_BUFLEN(x) (((x)&GEM_RD_BUFSIZE)>>GEM_RD_BUFSHIFT) #endif
