/* $NetBSD: tadpmureg.h,v 1.3 2020/05/16 07:16:14 jdc Exp $ */ /*- * Copyright (c) 2018 Michael Lorenz <macallan@netbsd.org> * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ /* registers and commands for the PMU found in Tadpole SPARCle/Viper laptops */ #ifndef TADPMUREG_H #define TADPMUREG_H /* all values were found by looking at OF methods on the tadpmu node */ /* these registers live in the pckbc's address space */ #define TADPMU_CMD 0x6 #define TADPMU_STATUS 0x6 #define TADPMU_DATA 0x2 #define STATUS_HAVE_DATA 0x01 /* response from command */ #define STATUS_CMD_IN_PROGRESS 0x02 #define STATUS_INTR 0x04 /* interrupt happened, read data to ack */ #define STATUS_SEND_DATA 0x08 /* cmd waiting for data */ #define CMD_SET_OPMODE 0x41 /* not sure what exactly this does... */ #define OPMODE_UNIX 0x75 /* other than toggling the UNIX mode */ #define OPMODE_OF 0x67 /* bit in the GENSTAT register */ #define OPMODE_DBG_ON 0x64 /* Debug ON */ #define OPMODE_DBG_OFF 0x6E /* Debug OFF */ #define OPMODE_OBP 0x6F #define CMD_CHRGCTL 0x42 #define CMD_SET_BACKLIGHT 0x43 /* apparently 0 - 1f */ #define CMD_SET_CPUSPEED 0x44 /* in 10MHz, so 120 == 1.2GHz */ #define CMD_SET_SPREADCLK 0x45 #define CMD_SET_FANSPEED 0x46 #define CMD_SET_VOLUME 0x48 /* beeper volume */ #define CMD_SET_DIR_CLK 0x80 #define CMD_WRITE 0xC0 #define CMD_READ_GENSTAT 0x10 #define CMD_READ_BACKLIGHT 0x11 #define CMD_READ_SYSTEMP 0x12 /* temperature */ #define CMD_READ_VOLUME 0x13 #define CMD_READ_VBATT 0x14 /* Voltage * 10 (e.g. 120 = 12.0v) */ #define CMD_READ_VERSION 0x15 #define CMD_READ_CPUSPEED 0x16 #define CMD_READ_KEYSTAT 0x17 /* Pause-A, D, N, O, R */ #define CMD_READ_FAN_EN 0x18 /* Fan(s): off=0x00, full=0x77 */ #define CMD_READ_GENSTAT2 0x19 #define READ_DIPSWITCH 0x1A #define CMD_READ_FANSPEED 0x50 /* takes a parameter, returns nothing? */ #define CMD_SHUTDOWN 0x40 #define CMD_BEEP 0x47 /* Start/stop beep, param is freq */ #define CMD_READ_BMU 0x70 #define CMD_REFLASH 0x49 #define CMD_READ 0x89 #define CMD_WRITE 0xC0 #define CMD_WRITE_BMU 0xC1 /* these are according to the ROM methods #define GENSTAT_DC_PRESENT 0x01 #define GENSTAT_DC_ENABLE 0x02 #define GENSTAT_BATTERY_PRESENT 0x04 #define GENSTAT_BATTERY_CHARGING 0x08 #define GENSTAT_LID_CLOSED 0x10 #define GENSTAT_UNIX_MODE 0x20 #define GENSTAT_SPREADSPECTRUM 0x40 Values of genstat (from observation) 0b = on battery 3b = battery charging 1f = battery full 1b = no battery */ #define GENSTAT_UNIX_MODE 0x01 #define GENSTAT_BATTERY_PRESENT 0x04 /* only valid if DC present? */ #define GENSTAT_BATTERY_CHARGED 0x08 #define GENSTAT_DC_PRESENT 0x10 #define GENSTAT_BATTERY_CHARGING 0x20 #define GENSTAT_LID_CLOSED 0x80 #define GENSTAT_STATE_BATTERY_FULL 0x1f #define GENSTAT_STATE_BATTERY_DISCHARGE 0x0b #define GENSTAT_STATE_BATTERY_CHARGE 0x3b #define GENSTAT2_DEBUG 0x01 /* PMU debug enable? */ #define GENSTAT2_MUTE 0x02 /* messages from interrupts */ #define TADPMU_INTR_BATTERY_CHARGED 0x03 #define TADPMU_INTR_DCPOWER 0x04 #define TADPMU_INTR_LID 0x05 #define TADPMU_INTR_POWERBUTTON 0x06 #define TADPMU_INTR_BATTERY_VOLT 0xcd /* Voltage change */ #define TADPMU_INTR_BATTERY_STATE 0xd6 /* e.g. warn -> crit */ /* Other observed values: 0xc9 0xcb 0xd2 */ #endif /* TADPMUREG_H */
