/*      $NetBSD: leds.c,v 1.16 2023/12/20 05:18:00 thorpej Exp $        */

/*-
 * Copyright (c) 1997 The NetBSD Foundation, Inc.
 * All rights reserved.
 *
 * This code is derived from software contributed to The NetBSD Foundation
 * by Gordon W. Ross and der Mouse.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
 * PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 */

/*
 * Functions to flash the LEDs with some pattern.
 * The 3/80 has just one LED on the front panel,
 * which we turn on during boot and leave alone.
 * All other Sun3 machines have an 8-position LED
 * array in which some pattern is animated.
 */

#include <sys/cdefs.h>
__KERNEL_RCSID(0, "$NetBSD: leds.c,v 1.16 2023/12/20 05:18:00 thorpej Exp $");

#include <sys/param.h>
#include <sys/systm.h>
#include <sys/device.h>
#include <sys/conf.h>
#include <sys/buf.h>
#include <sys/proc.h>

#include <uvm/uvm_extern.h>

#include <machine/autoconf.h>
#include <machine/idprom.h>
#include <machine/leds.h>

#include <sun3/sun3/machdep.h>
#ifdef  _SUN3_
#include <sun3/sun3/control.h>
#endif
#ifdef  _SUN3X_
#include <sun3/sun3x/obio.h>
static volatile uint8_t *diagreg;
#endif

static u_char led_countdown = 0;
static u_char led_px = 0;

/*
 * Initial value is the default pattern set. Note, only bit zero
 * shows on the 3/80, and it is active-high (3/470 is active-low).
 * We normally want the 3/80's LED to just stay ON, so the 3/80
 * will change the default patlen to one, causing the LED to keep
 * using the first byte of the pattern where bit zero is ON.
 */
static struct led_patterns ledpat = {
        8,      /* divisor */
        8,      /* patlen */
        {       /* patterns */
                0x0F, 0x1E, 0x3C, 0x78,
                0xF0, 0xE1, 0xC3, 0x87,
        }
};

/*
 * This is called early during startup to find the
 * diag register (LEDs) and turn on the light(s).
 */
void
leds_init(void)
{
#ifdef  _SUN3X_
        vaddr_t va;

        find_prom_map(OBIO_DIAGREG, PMAP_OBIO, 1, &va);
        diagreg = (void *)va;
        if (cpu_machine_id == ID_SUN3X_80)
                ledpat.patlen = 1;
#endif  /* SUN3X */

        /* Turn on some lights. */
        leds_intr();
}

/*
 * This is called by the clock interrupt.
 */
void
leds_intr(void)
{
        u_char i;

        if (led_countdown) {
                led_countdown--;
                return;
        }

        led_countdown = ledpat.divisor - 1;
        i = led_px;

#ifdef  _SUN3X_
        *diagreg = (char) ledpat.pat[i];
#else
        set_control_byte(DIAG_REG, ledpat.pat[i]);
#endif

        i = i+1;
        if (i == ledpat.patlen)
                i = 0;
        led_px = i;
}

/*
 * This is called by mem.c to handle /dev/leds
 */
int
leds_uio(struct uio *uio)
{
        int cnt, error;
        int off;        /* NOT off_t */
        void *va;

        off = uio->uio_offset;
        if ((off < 0) || (off > sizeof(ledpat)))
                return (EIO);

        cnt = uimin(uio->uio_resid, (sizeof(ledpat) - off));
        if (cnt == 0)
                return (0); /* EOF */

        va = ((char*)(&ledpat)) + off;
        error = uiomove(va, cnt, uio);

        return (error);
}