// SPDX-License-Identifier: GPL-2.0
//
// sgtl5000.c  --  SGTL5000 ALSA SoC Audio driver
//
// Copyright 2010-2011 Freescale Semiconductor, Inc. All Rights Reserved.

#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/slab.h>
#include <linux/pm.h>
#include <linux/i2c.h>
#include <linux/clk.h>
#include <linux/log2.h>
#include <linux/of.h>
#include <linux/regmap.h>
#include <linux/regulator/driver.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/consumer.h>
#include <sound/core.h>
#include <sound/tlv.h>
#include <sound/pcm.h>
#include <sound/pcm_params.h>
#include <sound/soc.h>
#include <sound/soc-dapm.h>
#include <sound/initval.h>

#include "sgtl5000.h"

#define SGTL5000_DAP_REG_OFFSET 0x0100
#define SGTL5000_MAX_REG_OFFSET 0x013A

/* Delay for the VAG ramp up */
#define SGTL5000_VAG_POWERUP_DELAY 500 /* ms */
/* Delay for the VAG ramp down */
#define SGTL5000_VAG_POWERDOWN_DELAY 500 /* ms */

#define SGTL5000_OUTPUTS_MUTE (SGTL5000_HP_MUTE | SGTL5000_LINE_OUT_MUTE)

/* default value of sgtl5000 registers */
static const struct reg_default sgtl5000_reg_defaults[] = {
        { SGTL5000_CHIP_DIG_POWER,              0x0000 },
        { SGTL5000_CHIP_I2S_CTRL,               0x0010 },
        { SGTL5000_CHIP_SSS_CTRL,               0x0010 },
        { SGTL5000_CHIP_ADCDAC_CTRL,            0x020c },
        { SGTL5000_CHIP_DAC_VOL,                0x3c3c },
        { SGTL5000_CHIP_PAD_STRENGTH,           0x015f },
        { SGTL5000_CHIP_ANA_ADC_CTRL,           0x0000 },
        { SGTL5000_CHIP_ANA_HP_CTRL,            0x1818 },
        { SGTL5000_CHIP_ANA_CTRL,               0x0111 },
        { SGTL5000_CHIP_REF_CTRL,               0x0000 },
        { SGTL5000_CHIP_MIC_CTRL,               0x0000 },
        { SGTL5000_CHIP_LINE_OUT_CTRL,          0x0000 },
        { SGTL5000_CHIP_LINE_OUT_VOL,           0x0404 },
        { SGTL5000_CHIP_PLL_CTRL,               0x5000 },
        { SGTL5000_CHIP_CLK_TOP_CTRL,           0x0000 },
        { SGTL5000_CHIP_ANA_STATUS,             0x0000 },
        { SGTL5000_CHIP_SHORT_CTRL,             0x0000 },
        { SGTL5000_CHIP_ANA_TEST2,              0x0000 },
        { SGTL5000_DAP_CTRL,                    0x0000 },
        { SGTL5000_DAP_PEQ,                     0x0000 },
        { SGTL5000_DAP_BASS_ENHANCE,            0x0040 },
        { SGTL5000_DAP_BASS_ENHANCE_CTRL,       0x051f },
        { SGTL5000_DAP_AUDIO_EQ,                0x0000 },
        { SGTL5000_DAP_SURROUND,                0x0040 },
        { SGTL5000_DAP_EQ_BASS_BAND0,           0x002f },
        { SGTL5000_DAP_EQ_BASS_BAND1,           0x002f },
        { SGTL5000_DAP_EQ_BASS_BAND2,           0x002f },
        { SGTL5000_DAP_EQ_BASS_BAND3,           0x002f },
        { SGTL5000_DAP_EQ_BASS_BAND4,           0x002f },
        { SGTL5000_DAP_MAIN_CHAN,               0x8000 },
        { SGTL5000_DAP_MIX_CHAN,                0x0000 },
        { SGTL5000_DAP_AVC_CTRL,                0x5100 },
        { SGTL5000_DAP_AVC_THRESHOLD,           0x1473 },
        { SGTL5000_DAP_AVC_ATTACK,              0x0028 },
        { SGTL5000_DAP_AVC_DECAY,               0x0050 },
};

/* AVC: Threshold dB -> register: pre-calculated values */
static const u16 avc_thr_db2reg[97] = {
        0x5168, 0x488E, 0x40AA, 0x39A1, 0x335D, 0x2DC7, 0x28CC, 0x245D, 0x2068,
        0x1CE2, 0x19BE, 0x16F1, 0x1472, 0x1239, 0x103E, 0x0E7A, 0x0CE6, 0x0B7F,
        0x0A3F, 0x0922, 0x0824, 0x0741, 0x0677, 0x05C3, 0x0522, 0x0493, 0x0414,
        0x03A2, 0x033D, 0x02E3, 0x0293, 0x024B, 0x020B, 0x01D2, 0x019F, 0x0172,
        0x014A, 0x0126, 0x0106, 0x00E9, 0x00D0, 0x00B9, 0x00A5, 0x0093, 0x0083,
        0x0075, 0x0068, 0x005D, 0x0052, 0x0049, 0x0041, 0x003A, 0x0034, 0x002E,
        0x0029, 0x0025, 0x0021, 0x001D, 0x001A, 0x0017, 0x0014, 0x0012, 0x0010,
        0x000E, 0x000D, 0x000B, 0x000A, 0x0009, 0x0008, 0x0007, 0x0006, 0x0005,
        0x0005, 0x0004, 0x0004, 0x0003, 0x0003, 0x0002, 0x0002, 0x0002, 0x0002,
        0x0001, 0x0001, 0x0001, 0x0001, 0x0001, 0x0001, 0x0000, 0x0000, 0x0000,
        0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000};

/* regulator supplies for sgtl5000, VDDD is an optional external supply */
enum sgtl5000_regulator_supplies {
        VDDA,
        VDDIO,
        VDDD,
        SGTL5000_SUPPLY_NUM
};

/* vddd is optional supply */
static const char *supply_names[SGTL5000_SUPPLY_NUM] = {
        "VDDA",
        "VDDIO",
        "VDDD"
};

#define LDO_VOLTAGE             1200000
#define LINREG_VDDD     ((1600 - LDO_VOLTAGE / 1000) / 50)

enum sgtl5000_micbias_resistor {
        SGTL5000_MICBIAS_OFF = 0,
        SGTL5000_MICBIAS_2K = 2,
        SGTL5000_MICBIAS_4K = 4,
        SGTL5000_MICBIAS_8K = 8,
};

enum  {
        I2S_LRCLK_STRENGTH_DISABLE,
        I2S_LRCLK_STRENGTH_LOW,
        I2S_LRCLK_STRENGTH_MEDIUM,
        I2S_LRCLK_STRENGTH_HIGH,
};

enum  {
        I2S_SCLK_STRENGTH_DISABLE,
        I2S_SCLK_STRENGTH_LOW,
        I2S_SCLK_STRENGTH_MEDIUM,
        I2S_SCLK_STRENGTH_HIGH,
};

enum {
        HP_POWER_EVENT,
        DAC_POWER_EVENT,
        ADC_POWER_EVENT,
        LAST_POWER_EVENT = ADC_POWER_EVENT
};

/* sgtl5000 private structure in codec */
struct sgtl5000_priv {
        int sysclk;     /* sysclk rate */
        int master;     /* i2s master or not */
        int fmt;        /* i2s data format */
        struct regulator_bulk_data supplies[SGTL5000_SUPPLY_NUM];
        int num_supplies;
        struct regmap *regmap;
        struct clk *mclk;
        int revision;
        u8 micbias_resistor;
        u8 micbias_voltage;
        u8 lrclk_strength;
        u8 sclk_strength;
        u16 mute_state[LAST_POWER_EVENT + 1];
};

static inline int hp_sel_input(struct snd_soc_component *component)
{
        return (snd_soc_component_read(component, SGTL5000_CHIP_ANA_CTRL) &
                SGTL5000_HP_SEL_MASK) >> SGTL5000_HP_SEL_SHIFT;
}

static inline u16 mute_output(struct snd_soc_component *component,
                              u16 mute_mask)
{
        u16 mute_reg = snd_soc_component_read(component,
                                              SGTL5000_CHIP_ANA_CTRL);

        snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_CTRL,
                            mute_mask, mute_mask);
        return mute_reg;
}

static inline void restore_output(struct snd_soc_component *component,
                                  u16 mute_mask, u16 mute_reg)
{
        snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_CTRL,
                mute_mask, mute_reg);
}

static void vag_power_on(struct snd_soc_component *component, u32 source)
{
        if (snd_soc_component_read(component, SGTL5000_CHIP_ANA_POWER) &
            SGTL5000_VAG_POWERUP)
                return;

        snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER,
                            SGTL5000_VAG_POWERUP, SGTL5000_VAG_POWERUP);

        /* When VAG powering on to get local loop from Line-In, the sleep
         * is required to avoid loud pop.
         */
        if (hp_sel_input(component) == SGTL5000_HP_SEL_LINE_IN &&
            source == HP_POWER_EVENT)
                msleep(SGTL5000_VAG_POWERUP_DELAY);
}

static int vag_power_consumers(struct snd_soc_component *component,
                               u16 ana_pwr_reg, u32 source)
{
        int consumers = 0;

        /* count dac/adc consumers unconditional */
        if (ana_pwr_reg & SGTL5000_DAC_POWERUP)
                consumers++;
        if (ana_pwr_reg & SGTL5000_ADC_POWERUP)
                consumers++;

        /*
         * If the event comes from HP and Line-In is selected,
         * current action is 'DAC to be powered down'.
         * As HP_POWERUP is not set when HP muxed to line-in,
         * we need to keep VAG power ON.
         */
        if (source == HP_POWER_EVENT) {
                if (hp_sel_input(component) == SGTL5000_HP_SEL_LINE_IN)
                        consumers++;
        } else {
                if (ana_pwr_reg & SGTL5000_HP_POWERUP)
                        consumers++;
        }

        return consumers;
}

static void vag_power_off(struct snd_soc_component *component, u32 source)
{
        u16 ana_pwr = snd_soc_component_read(component,
                                             SGTL5000_CHIP_ANA_POWER);

        if (!(ana_pwr & SGTL5000_VAG_POWERUP))
                return;

        /*
         * This function calls when any of VAG power consumers is disappearing.
         * Thus, if there is more than one consumer at the moment, as minimum
         * one consumer will definitely stay after the end of the current
         * event.
         * Don't clear VAG_POWERUP if 2 or more consumers of VAG present:
         * - LINE_IN (for HP events) / HP (for DAC/ADC events)
         * - DAC
         * - ADC
         * (the current consumer is disappearing right now)
         */
        if (vag_power_consumers(component, ana_pwr, source) >= 2)
                return;

        snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER,
                SGTL5000_VAG_POWERUP, 0);
        /* In power down case, we need wait 400-1000 ms
         * when VAG fully ramped down.
         * As longer we wait, as smaller pop we've got.
         */
        msleep(SGTL5000_VAG_POWERDOWN_DELAY);
}

/*
 * mic_bias power on/off share the same register bits with
 * output impedance of mic bias, when power on mic bias, we
 * need reclaim it to impedance value.
 * 0x0 = Powered off
 * 0x1 = 2Kohm
 * 0x2 = 4Kohm
 * 0x3 = 8Kohm
 */
static int mic_bias_event(struct snd_soc_dapm_widget *w,
        struct snd_kcontrol *kcontrol, int event)
{
        struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
        struct sgtl5000_priv *sgtl5000 = snd_soc_component_get_drvdata(component);

        switch (event) {
        case SND_SOC_DAPM_POST_PMU:
                /* change mic bias resistor */
                snd_soc_component_update_bits(component, SGTL5000_CHIP_MIC_CTRL,
                        SGTL5000_BIAS_R_MASK,
                        sgtl5000->micbias_resistor << SGTL5000_BIAS_R_SHIFT);
                break;

        case SND_SOC_DAPM_PRE_PMD:
                snd_soc_component_update_bits(component, SGTL5000_CHIP_MIC_CTRL,
                                SGTL5000_BIAS_R_MASK, 0);
                break;
        }
        return 0;
}

static int vag_and_mute_control(struct snd_soc_component *component,
                                 int event, int event_source)
{
        static const u16 mute_mask[] = {
                /*
                 * Mask for HP_POWER_EVENT.
                 * Muxing Headphones have to be wrapped with mute/unmute
                 * headphones only.
                 */
                SGTL5000_HP_MUTE,
                /*
                 * Masks for DAC_POWER_EVENT/ADC_POWER_EVENT.
                 * Muxing DAC or ADC block have to wrapped with mute/unmute
                 * both headphones and line-out.
                 */
                SGTL5000_OUTPUTS_MUTE,
                SGTL5000_OUTPUTS_MUTE
        };

        struct sgtl5000_priv *sgtl5000 =
                snd_soc_component_get_drvdata(component);

        switch (event) {
        case SND_SOC_DAPM_PRE_PMU:
                sgtl5000->mute_state[event_source] =
                        mute_output(component, mute_mask[event_source]);
                break;
        case SND_SOC_DAPM_POST_PMU:
                vag_power_on(component, event_source);
                restore_output(component, mute_mask[event_source],
                               sgtl5000->mute_state[event_source]);
                break;
        case SND_SOC_DAPM_PRE_PMD:
                sgtl5000->mute_state[event_source] =
                        mute_output(component, mute_mask[event_source]);
                vag_power_off(component, event_source);
                break;
        case SND_SOC_DAPM_POST_PMD:
                restore_output(component, mute_mask[event_source],
                               sgtl5000->mute_state[event_source]);
                break;
        default:
                break;
        }

        return 0;
}

/*
 * Mute Headphone when power it up/down.
 * Control VAG power on HP power path.
 */
static int headphone_pga_event(struct snd_soc_dapm_widget *w,
        struct snd_kcontrol *kcontrol, int event)
{
        struct snd_soc_component *component =
                snd_soc_dapm_to_component(w->dapm);

        return vag_and_mute_control(component, event, HP_POWER_EVENT);
}

/* As manual describes, ADC/DAC powering up/down requires
 * to mute outputs to avoid pops.
 * Control VAG power on ADC/DAC power path.
 */
static int adc_updown_depop(struct snd_soc_dapm_widget *w,
        struct snd_kcontrol *kcontrol, int event)
{
        struct snd_soc_component *component =
                snd_soc_dapm_to_component(w->dapm);

        return vag_and_mute_control(component, event, ADC_POWER_EVENT);
}

static int dac_updown_depop(struct snd_soc_dapm_widget *w,
        struct snd_kcontrol *kcontrol, int event)
{
        struct snd_soc_component *component =
                snd_soc_dapm_to_component(w->dapm);

        return vag_and_mute_control(component, event, DAC_POWER_EVENT);
}

/* input sources for ADC */
static const char *adc_mux_text[] = {
        "MIC_IN", "LINE_IN"
};

static SOC_ENUM_SINGLE_DECL(adc_enum,
                            SGTL5000_CHIP_ANA_CTRL, 2,
                            adc_mux_text);

static const struct snd_kcontrol_new adc_mux =
SOC_DAPM_ENUM("Capture Mux", adc_enum);

/* input sources for headphone */
static const char *hp_mux_text[] = {
        "DAC", "LINE_IN"
};

static SOC_ENUM_SINGLE_DECL(hp_enum,
                            SGTL5000_CHIP_ANA_CTRL, 6,
                            hp_mux_text);

static const struct snd_kcontrol_new hp_mux =
SOC_DAPM_ENUM("Headphone Mux", hp_enum);

/* input sources for DAC */
static const char *dac_mux_text[] = {
        "ADC", "I2S", "Rsvrd", "DAP"
};

static SOC_ENUM_SINGLE_DECL(dac_enum,
                            SGTL5000_CHIP_SSS_CTRL, SGTL5000_DAC_SEL_SHIFT,
                            dac_mux_text);

static const struct snd_kcontrol_new dac_mux =
SOC_DAPM_ENUM("Digital Input Mux", dac_enum);

/* input sources for DAP */
static const char *dap_mux_text[] = {
        "ADC", "I2S"
};

static SOC_ENUM_SINGLE_DECL(dap_enum,
                            SGTL5000_CHIP_SSS_CTRL, SGTL5000_DAP_SEL_SHIFT,
                            dap_mux_text);

static const struct snd_kcontrol_new dap_mux =
SOC_DAPM_ENUM("DAP Mux", dap_enum);

/* input sources for DAP mix */
static const char *dapmix_mux_text[] = {
        "ADC", "I2S"
};

static SOC_ENUM_SINGLE_DECL(dapmix_enum,
                            SGTL5000_CHIP_SSS_CTRL, SGTL5000_DAP_MIX_SEL_SHIFT,
                            dapmix_mux_text);

static const struct snd_kcontrol_new dapmix_mux =
SOC_DAPM_ENUM("DAP MIX Mux", dapmix_enum);


static const struct snd_soc_dapm_widget sgtl5000_dapm_widgets[] = {
        SND_SOC_DAPM_INPUT("LINE_IN"),
        SND_SOC_DAPM_INPUT("MIC_IN"),

        SND_SOC_DAPM_OUTPUT("HP_OUT"),
        SND_SOC_DAPM_OUTPUT("LINE_OUT"),

        SND_SOC_DAPM_SUPPLY("Mic Bias", SGTL5000_CHIP_MIC_CTRL, 8, 0,
                            mic_bias_event,
                            SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),

        SND_SOC_DAPM_PGA_E("HP", SGTL5000_CHIP_ANA_POWER, 4, 0, NULL, 0,
                           headphone_pga_event,
                           SND_SOC_DAPM_PRE_POST_PMU |
                           SND_SOC_DAPM_PRE_POST_PMD),
        SND_SOC_DAPM_PGA("LO", SGTL5000_CHIP_ANA_POWER, 0, 0, NULL, 0),

        SND_SOC_DAPM_MUX("Capture Mux", SND_SOC_NOPM, 0, 0, &adc_mux),
        SND_SOC_DAPM_MUX("Headphone Mux", SND_SOC_NOPM, 0, 0, &hp_mux),
        SND_SOC_DAPM_MUX("Digital Input Mux", SND_SOC_NOPM, 0, 0, &dac_mux),
        SND_SOC_DAPM_MUX("DAP Mux", SGTL5000_DAP_CTRL, 0, 0, &dap_mux),
        SND_SOC_DAPM_MUX("DAP MIX Mux", SGTL5000_DAP_CTRL, 4, 0, &dapmix_mux),
        SND_SOC_DAPM_MIXER("DAP", SGTL5000_CHIP_DIG_POWER, 4, 0, NULL, 0),


        /* aif for i2s input */
        SND_SOC_DAPM_AIF_IN("AIFIN", "Playback",
                                0, SGTL5000_CHIP_DIG_POWER,
                                0, 0),

        /* aif for i2s output */
        SND_SOC_DAPM_AIF_OUT("AIFOUT", "Capture",
                                0, SGTL5000_CHIP_DIG_POWER,
                                1, 0),

        SND_SOC_DAPM_ADC_E("ADC", "Capture", SGTL5000_CHIP_ANA_POWER, 1, 0,
                           adc_updown_depop, SND_SOC_DAPM_PRE_POST_PMU |
                           SND_SOC_DAPM_PRE_POST_PMD),
        SND_SOC_DAPM_DAC_E("DAC", "Playback", SGTL5000_CHIP_ANA_POWER, 3, 0,
                           dac_updown_depop, SND_SOC_DAPM_PRE_POST_PMU |
                           SND_SOC_DAPM_PRE_POST_PMD),
};

/* routes for sgtl5000 */
static const struct snd_soc_dapm_route sgtl5000_dapm_routes[] = {
        {"Capture Mux", "LINE_IN", "LINE_IN"},  /* line_in --> adc_mux */
        {"Capture Mux", "MIC_IN", "MIC_IN"},    /* mic_in --> adc_mux */

        {"ADC", NULL, "Capture Mux"},           /* adc_mux --> adc */
        {"AIFOUT", NULL, "ADC"},                /* adc --> i2s_out */

        {"DAP Mux", "ADC", "ADC"},              /* adc --> DAP mux */
        {"DAP Mux", NULL, "AIFIN"},             /* i2s --> DAP mux */
        {"DAP", NULL, "DAP Mux"},               /* DAP mux --> dap */

        {"DAP MIX Mux", "ADC", "ADC"},          /* adc --> DAP MIX mux */
        {"DAP MIX Mux", NULL, "AIFIN"},         /* i2s --> DAP MIX mux */
        {"DAP", NULL, "DAP MIX Mux"},           /* DAP MIX mux --> dap */

        {"Digital Input Mux", "ADC", "ADC"},    /* adc --> audio mux */
        {"Digital Input Mux", NULL, "AIFIN"},   /* i2s --> audio mux */
        {"Digital Input Mux", NULL, "DAP"},     /* dap --> audio mux */
        {"DAC", NULL, "Digital Input Mux"},     /* audio mux --> dac */

        {"Headphone Mux", "DAC", "DAC"},        /* dac --> hp_mux */
        {"LO", NULL, "DAC"},                    /* dac --> line_out */

        {"Headphone Mux", "LINE_IN", "LINE_IN"},/* line_in --> hp_mux */
        {"HP", NULL, "Headphone Mux"},          /* hp_mux --> hp */

        {"LINE_OUT", NULL, "LO"},
        {"HP_OUT", NULL, "HP"},
};

/* custom function to fetch info of PCM playback volume */
static int dac_info_volsw(struct snd_kcontrol *kcontrol,
                          struct snd_ctl_elem_info *uinfo)
{
        uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
        uinfo->count = 2;
        uinfo->value.integer.min = 0;
        uinfo->value.integer.max = 0xfc - 0x3c;
        return 0;
}

/*
 * custom function to get of PCM playback volume
 *
 * dac volume register
 * 15-------------8-7--------------0
 * | R channel vol | L channel vol |
 *  -------------------------------
 *
 * PCM volume with 0.5017 dB steps from 0 to -90 dB
 *
 * register values map to dB
 * 0x3B and less = Reserved
 * 0x3C = 0 dB
 * 0x3D = -0.5 dB
 * 0xF0 = -90 dB
 * 0xFC and greater = Muted
 *
 * register value map to userspace value
 *
 * register value       0x3c(0dB)         0xf0(-90dB)0xfc
 *                      ------------------------------
 * userspace value      0xc0                         0
 */
static int dac_get_volsw(struct snd_kcontrol *kcontrol,
                         struct snd_ctl_elem_value *ucontrol)
{
        struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
        int reg;
        int l;
        int r;

        reg = snd_soc_component_read(component, SGTL5000_CHIP_DAC_VOL);

        /* get left channel volume */
        l = (reg & SGTL5000_DAC_VOL_LEFT_MASK) >> SGTL5000_DAC_VOL_LEFT_SHIFT;

        /* get right channel volume */
        r = (reg & SGTL5000_DAC_VOL_RIGHT_MASK) >> SGTL5000_DAC_VOL_RIGHT_SHIFT;

        /* make sure value fall in (0x3c,0xfc) */
        l = clamp(l, 0x3c, 0xfc);
        r = clamp(r, 0x3c, 0xfc);

        /* invert it and map to userspace value */
        l = 0xfc - l;
        r = 0xfc - r;

        ucontrol->value.integer.value[0] = l;
        ucontrol->value.integer.value[1] = r;

        return 0;
}

/*
 * custom function to put of PCM playback volume
 *
 * dac volume register
 * 15-------------8-7--------------0
 * | R channel vol | L channel vol |
 *  -------------------------------
 *
 * PCM volume with 0.5017 dB steps from 0 to -90 dB
 *
 * register values map to dB
 * 0x3B and less = Reserved
 * 0x3C = 0 dB
 * 0x3D = -0.5 dB
 * 0xF0 = -90 dB
 * 0xFC and greater = Muted
 *
 * userspace value map to register value
 *
 * userspace value      0xc0                         0
 *                      ------------------------------
 * register value       0x3c(0dB)       0xf0(-90dB)0xfc
 */
static int dac_put_volsw(struct snd_kcontrol *kcontrol,
                         struct snd_ctl_elem_value *ucontrol)
{
        struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
        int reg;
        int l;
        int r;

        l = ucontrol->value.integer.value[0];
        r = ucontrol->value.integer.value[1];

        /* make sure userspace volume fall in (0, 0xfc-0x3c) */
        l = clamp(l, 0, 0xfc - 0x3c);
        r = clamp(r, 0, 0xfc - 0x3c);

        /* invert it, get the value can be set to register */
        l = 0xfc - l;
        r = 0xfc - r;

        /* shift to get the register value */
        reg = l << SGTL5000_DAC_VOL_LEFT_SHIFT |
                r << SGTL5000_DAC_VOL_RIGHT_SHIFT;

        snd_soc_component_write(component, SGTL5000_CHIP_DAC_VOL, reg);

        return 0;
}

/*
 * custom function to get AVC threshold
 *
 * The threshold dB is calculated by rearranging the calculation from the
 * avc_put_threshold function: register_value = 10^(dB/20) * 0.636 * 2^15 ==>
 * dB = ( fls(register_value) - 14.347 ) * 6.02
 *
 * As this calculation is expensive and the threshold dB values may not exceed
 * 0 to 96 we use pre-calculated values.
 */
static int avc_get_threshold(struct snd_kcontrol *kcontrol,
                             struct snd_ctl_elem_value *ucontrol)
{
        struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
        int db, i;
        u16 reg = snd_soc_component_read(component, SGTL5000_DAP_AVC_THRESHOLD);

        /* register value 0 => -96dB */
        if (!reg) {
                ucontrol->value.integer.value[0] = 96;
                ucontrol->value.integer.value[1] = 96;
                return 0;
        }

        /* get dB from register value (rounded down) */
        for (i = 0; avc_thr_db2reg[i] > reg; i++)
                ;
        db = i;

        ucontrol->value.integer.value[0] = db;
        ucontrol->value.integer.value[1] = db;

        return 0;
}

/*
 * custom function to put AVC threshold
 *
 * The register value is calculated by following formula:
 *                                    register_value = 10^(dB/20) * 0.636 * 2^15
 * As this calculation is expensive and the threshold dB values may not exceed
 * 0 to 96 we use pre-calculated values.
 */
static int avc_put_threshold(struct snd_kcontrol *kcontrol,
                             struct snd_ctl_elem_value *ucontrol)
{
        struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
        int db;
        u16 reg;

        db = (int)ucontrol->value.integer.value[0];
        if (db < 0 || db > 96)
                return -EINVAL;
        reg = avc_thr_db2reg[db];
        snd_soc_component_write(component, SGTL5000_DAP_AVC_THRESHOLD, reg);

        return 0;
}

static const DECLARE_TLV_DB_SCALE(capture_6db_attenuate, -600, 600, 0);

/* tlv for mic gain, 0db 20db 30db 40db */
static const DECLARE_TLV_DB_RANGE(mic_gain_tlv,
        0, 0, TLV_DB_SCALE_ITEM(0, 0, 0),
        1, 3, TLV_DB_SCALE_ITEM(2000, 1000, 0)
);

/* tlv for DAP channels, 0% - 100% - 200% */
static const DECLARE_TLV_DB_SCALE(dap_volume, 0, 1, 0);

/* tlv for bass bands, -11.75db to 12.0db, step .25db */
static const DECLARE_TLV_DB_SCALE(bass_band, -1175, 25, 0);

/* tlv for hp volume, -51.5db to 12.0db, step .5db */
static const DECLARE_TLV_DB_SCALE(headphone_volume, -5150, 50, 0);

/* tlv for lineout volume, 31 steps of .5db each */
static const DECLARE_TLV_DB_SCALE(lineout_volume, -1550, 50, 0);

/* tlv for dap avc max gain, 0db, 6db, 12db */
static const DECLARE_TLV_DB_SCALE(avc_max_gain, 0, 600, 0);

/* tlv for dap avc threshold, */
static const DECLARE_TLV_DB_MINMAX(avc_threshold, 0, 9600);

static const struct snd_kcontrol_new sgtl5000_snd_controls[] = {
        /* SOC_DOUBLE_S8_TLV with invert */
        {
                .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
                .name = "PCM Playback Volume",
                .access = SNDRV_CTL_ELEM_ACCESS_TLV_READ |
                        SNDRV_CTL_ELEM_ACCESS_READWRITE,
                .info = dac_info_volsw,
                .get = dac_get_volsw,
                .put = dac_put_volsw,
        },

        SOC_DOUBLE("Capture Volume", SGTL5000_CHIP_ANA_ADC_CTRL, 0, 4, 0xf, 0),
        SOC_SINGLE_TLV("Capture Attenuate Switch (-6dB)",
                        SGTL5000_CHIP_ANA_ADC_CTRL,
                        8, 1, 0, capture_6db_attenuate),
        SOC_SINGLE("Capture ZC Switch", SGTL5000_CHIP_ANA_CTRL, 1, 1, 0),
        SOC_SINGLE("Capture Switch", SGTL5000_CHIP_ANA_CTRL, 0, 1, 1),

        SOC_DOUBLE_TLV("Headphone Playback Volume",
                        SGTL5000_CHIP_ANA_HP_CTRL,
                        0, 8,
                        0x7f, 1,
                        headphone_volume),
        SOC_SINGLE("Headphone Playback Switch", SGTL5000_CHIP_ANA_CTRL,
                        4, 1, 1),
        SOC_SINGLE("Headphone Playback ZC Switch", SGTL5000_CHIP_ANA_CTRL,
                        5, 1, 0),

        SOC_SINGLE_TLV("Mic Volume", SGTL5000_CHIP_MIC_CTRL,
                        0, 3, 0, mic_gain_tlv),

        SOC_DOUBLE_TLV("Lineout Playback Volume",
                        SGTL5000_CHIP_LINE_OUT_VOL,
                        SGTL5000_LINE_OUT_VOL_LEFT_SHIFT,
                        SGTL5000_LINE_OUT_VOL_RIGHT_SHIFT,
                        0x1f, 1,
                        lineout_volume),
        SOC_SINGLE("Lineout Playback Switch", SGTL5000_CHIP_ANA_CTRL, 8, 1, 1),

        SOC_SINGLE_TLV("DAP Main channel", SGTL5000_DAP_MAIN_CHAN,
        0, 0xffff, 0, dap_volume),

        SOC_SINGLE_TLV("DAP Mix channel", SGTL5000_DAP_MIX_CHAN,
        0, 0xffff, 0, dap_volume),
        /* Automatic Volume Control (DAP AVC) */
        SOC_SINGLE("AVC Switch", SGTL5000_DAP_AVC_CTRL, 0, 1, 0),
        SOC_SINGLE("AVC Hard Limiter Switch", SGTL5000_DAP_AVC_CTRL, 5, 1, 0),
        SOC_SINGLE_TLV("AVC Max Gain Volume", SGTL5000_DAP_AVC_CTRL, 12, 2, 0,
                        avc_max_gain),
        SOC_SINGLE("AVC Integrator Response", SGTL5000_DAP_AVC_CTRL, 8, 3, 0),
        SOC_SINGLE_EXT_TLV("AVC Threshold Volume", SGTL5000_DAP_AVC_THRESHOLD,
                        0, 96, 0, avc_get_threshold, avc_put_threshold,
                        avc_threshold),

        SOC_SINGLE_TLV("BASS 0", SGTL5000_DAP_EQ_BASS_BAND0,
        0, 0x5F, 0, bass_band),

        SOC_SINGLE_TLV("BASS 1", SGTL5000_DAP_EQ_BASS_BAND1,
        0, 0x5F, 0, bass_band),

        SOC_SINGLE_TLV("BASS 2", SGTL5000_DAP_EQ_BASS_BAND2,
        0, 0x5F, 0, bass_band),

        SOC_SINGLE_TLV("BASS 3", SGTL5000_DAP_EQ_BASS_BAND3,
        0, 0x5F, 0, bass_band),

        SOC_SINGLE_TLV("BASS 4", SGTL5000_DAP_EQ_BASS_BAND4,
        0, 0x5F, 0, bass_band),
};

/* mute the codec used by alsa core */
static int sgtl5000_mute_stream(struct snd_soc_dai *codec_dai, int mute, int direction)
{
        struct snd_soc_component *component = codec_dai->component;
        u16 i2s_pwr = SGTL5000_I2S_IN_POWERUP;

        /*
         * During 'digital mute' do not mute DAC
         * because LINE_IN would be muted aswell. We want to mute
         * only I2S block - this can be done by powering it off
         */
        snd_soc_component_update_bits(component, SGTL5000_CHIP_DIG_POWER,
                        i2s_pwr, mute ? 0 : i2s_pwr);

        return 0;
}

/* set codec format */
static int sgtl5000_set_dai_fmt(struct snd_soc_dai *codec_dai, unsigned int fmt)
{
        struct snd_soc_component *component = codec_dai->component;
        struct sgtl5000_priv *sgtl5000 = snd_soc_component_get_drvdata(component);
        u16 i2sctl = 0;

        sgtl5000->master = 0;
        /*
         * i2s clock and frame master setting.
         * ONLY support:
         *  - clock and frame slave,
         *  - clock and frame master
         */
        switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
        case SND_SOC_DAIFMT_CBC_CFC:
                break;
        case SND_SOC_DAIFMT_CBP_CFP:
                i2sctl |= SGTL5000_I2S_MASTER;
                sgtl5000->master = 1;
                break;
        default:
                return -EINVAL;
        }

        /* setting i2s data format */
        switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
        case SND_SOC_DAIFMT_DSP_A:
                i2sctl |= SGTL5000_I2S_MODE_PCM << SGTL5000_I2S_MODE_SHIFT;
                break;
        case SND_SOC_DAIFMT_DSP_B:
                i2sctl |= SGTL5000_I2S_MODE_PCM << SGTL5000_I2S_MODE_SHIFT;
                i2sctl |= SGTL5000_I2S_LRALIGN;
                break;
        case SND_SOC_DAIFMT_I2S:
                i2sctl |= SGTL5000_I2S_MODE_I2S_LJ << SGTL5000_I2S_MODE_SHIFT;
                break;
        case SND_SOC_DAIFMT_RIGHT_J:
                i2sctl |= SGTL5000_I2S_MODE_RJ << SGTL5000_I2S_MODE_SHIFT;
                i2sctl |= SGTL5000_I2S_LRPOL;
                break;
        case SND_SOC_DAIFMT_LEFT_J:
                i2sctl |= SGTL5000_I2S_MODE_I2S_LJ << SGTL5000_I2S_MODE_SHIFT;
                i2sctl |= SGTL5000_I2S_LRALIGN;
                break;
        default:
                return -EINVAL;
        }

        sgtl5000->fmt = fmt & SND_SOC_DAIFMT_FORMAT_MASK;

        /* Clock inversion */
        switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
        case SND_SOC_DAIFMT_NB_NF:
                break;
        case SND_SOC_DAIFMT_IB_NF:
                i2sctl |= SGTL5000_I2S_SCLK_INV;
                break;
        default:
                return -EINVAL;
        }

        snd_soc_component_write(component, SGTL5000_CHIP_I2S_CTRL, i2sctl);

        return 0;
}

/* set codec sysclk */
static int sgtl5000_set_dai_sysclk(struct snd_soc_dai *codec_dai,
                                   int clk_id, unsigned int freq, int dir)
{
        struct snd_soc_component *component = codec_dai->component;
        struct sgtl5000_priv *sgtl5000 = snd_soc_component_get_drvdata(component);

        switch (clk_id) {
        case SGTL5000_SYSCLK:
                sgtl5000->sysclk = freq;
                break;
        default:
                return -EINVAL;
        }

        return 0;
}

/*
 * set clock according to i2s frame clock,
 * sgtl5000 provides 2 clock sources:
 * 1. sys_mclk: sample freq can only be configured to
 *      1/256, 1/384, 1/512 of sys_mclk.
 * 2. pll: can derive any audio clocks.
 *
 * clock setting rules:
 * 1. in slave mode, only sys_mclk can be used
 * 2. as constraint by sys_mclk, sample freq should be set to 32 kHz, 44.1 kHz
 * and above.
 * 3. usage of sys_mclk is preferred over pll to save power.
 */
static int sgtl5000_set_clock(struct snd_soc_component *component, int frame_rate)
{
        struct sgtl5000_priv *sgtl5000 = snd_soc_component_get_drvdata(component);
        int clk_ctl = 0;
        int sys_fs;     /* sample freq */

        /*
         * sample freq should be divided by frame clock,
         * if frame clock is lower than 44.1 kHz, sample freq should be set to
         * 32 kHz or 44.1 kHz.
         */
        switch (frame_rate) {
        case 8000:
        case 16000:
                sys_fs = 32000;
                break;
        case 11025:
        case 22050:
                sys_fs = 44100;
                break;
        default:
                sys_fs = frame_rate;
                break;
        }

        /* set divided factor of frame clock */
        switch (sys_fs / frame_rate) {
        case 4:
                clk_ctl |= SGTL5000_RATE_MODE_DIV_4 << SGTL5000_RATE_MODE_SHIFT;
                break;
        case 2:
                clk_ctl |= SGTL5000_RATE_MODE_DIV_2 << SGTL5000_RATE_MODE_SHIFT;
                break;
        case 1:
                clk_ctl |= SGTL5000_RATE_MODE_DIV_1 << SGTL5000_RATE_MODE_SHIFT;
                break;
        default:
                return -EINVAL;
        }

        /* set the sys_fs according to frame rate */
        switch (sys_fs) {
        case 32000:
                clk_ctl |= SGTL5000_SYS_FS_32k << SGTL5000_SYS_FS_SHIFT;
                break;
        case 44100:
                clk_ctl |= SGTL5000_SYS_FS_44_1k << SGTL5000_SYS_FS_SHIFT;
                break;
        case 48000:
                clk_ctl |= SGTL5000_SYS_FS_48k << SGTL5000_SYS_FS_SHIFT;
                break;
        case 96000:
                clk_ctl |= SGTL5000_SYS_FS_96k << SGTL5000_SYS_FS_SHIFT;
                break;
        default:
                dev_err(component->dev, "frame rate %d not supported\n",
                        frame_rate);
                return -EINVAL;
        }

        /*
         * calculate the divider of mclk/sample_freq,
         * factor of freq = 96 kHz can only be 256, since mclk is in the range
         * of 8 MHz - 27 MHz
         */
        switch (sgtl5000->sysclk / frame_rate) {
        case 256:
                clk_ctl |= SGTL5000_MCLK_FREQ_256FS <<
                        SGTL5000_MCLK_FREQ_SHIFT;
                break;
        case 384:
                clk_ctl |= SGTL5000_MCLK_FREQ_384FS <<
                        SGTL5000_MCLK_FREQ_SHIFT;
                break;
        case 512:
                clk_ctl |= SGTL5000_MCLK_FREQ_512FS <<
                        SGTL5000_MCLK_FREQ_SHIFT;
                break;
        default:
                /* if mclk does not satisfy the divider, use pll */
                if (sgtl5000->master) {
                        clk_ctl |= SGTL5000_MCLK_FREQ_PLL <<
                                SGTL5000_MCLK_FREQ_SHIFT;
                } else {
                        dev_err(component->dev,
                                "PLL not supported in slave mode\n");
                        dev_err(component->dev, "%d ratio is not supported. "
                                "SYS_MCLK needs to be 256, 384 or 512 * fs\n",
                                sgtl5000->sysclk / frame_rate);
                        return -EINVAL;
                }
        }

        /* if using pll, please check manual 6.4.2 for detail */
        if ((clk_ctl & SGTL5000_MCLK_FREQ_MASK) == SGTL5000_MCLK_FREQ_PLL) {
                u64 out, t;
                int div2;
                int pll_ctl;
                unsigned int in, int_div, frac_div;

                if (sgtl5000->sysclk > 17000000) {
                        div2 = 1;
                        in = sgtl5000->sysclk / 2;
                } else {
                        div2 = 0;
                        in = sgtl5000->sysclk;
                }
                if (sys_fs == 44100)
                        out = 180633600;
                else
                        out = 196608000;
                t = do_div(out, in);
                int_div = out;
                t *= 2048;
                do_div(t, in);
                frac_div = t;
                pll_ctl = int_div << SGTL5000_PLL_INT_DIV_SHIFT |
                    frac_div << SGTL5000_PLL_FRAC_DIV_SHIFT;

                snd_soc_component_write(component, SGTL5000_CHIP_PLL_CTRL, pll_ctl);
                if (div2)
                        snd_soc_component_update_bits(component,
                                SGTL5000_CHIP_CLK_TOP_CTRL,
                                SGTL5000_INPUT_FREQ_DIV2,
                                SGTL5000_INPUT_FREQ_DIV2);
                else
                        snd_soc_component_update_bits(component,
                                SGTL5000_CHIP_CLK_TOP_CTRL,
                                SGTL5000_INPUT_FREQ_DIV2,
                                0);

                /* power up pll */
                snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER,
                        SGTL5000_PLL_POWERUP | SGTL5000_VCOAMP_POWERUP,
                        SGTL5000_PLL_POWERUP | SGTL5000_VCOAMP_POWERUP);

                /* if using pll, clk_ctrl must be set after pll power up */
                snd_soc_component_write(component, SGTL5000_CHIP_CLK_CTRL, clk_ctl);
        } else {
                /* otherwise, clk_ctrl must be set before pll power down */
                snd_soc_component_write(component, SGTL5000_CHIP_CLK_CTRL, clk_ctl);

                /* power down pll */
                snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER,
                        SGTL5000_PLL_POWERUP | SGTL5000_VCOAMP_POWERUP,
                        0);
        }

        return 0;
}

/*
 * Set PCM DAI bit size and sample rate.
 * input: params_rate, params_fmt
 */
static int sgtl5000_pcm_hw_params(struct snd_pcm_substream *substream,
                                  struct snd_pcm_hw_params *params,
                                  struct snd_soc_dai *dai)
{
        struct snd_soc_component *component = dai->component;
        struct sgtl5000_priv *sgtl5000 = snd_soc_component_get_drvdata(component);
        int channels = params_channels(params);
        int i2s_ctl = 0;
        int stereo;
        int ret;

        /* sysclk should already set */
        if (!sgtl5000->sysclk) {
                dev_err(component->dev, "%s: set sysclk first!\n", __func__);
                return -EFAULT;
        }

        if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
                stereo = SGTL5000_DAC_STEREO;
        else
                stereo = SGTL5000_ADC_STEREO;

        /* set mono to save power */
        snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER, stereo,
                        channels == 1 ? 0 : stereo);

        /* set codec clock base on lrclk */
        ret = sgtl5000_set_clock(component, params_rate(params));
        if (ret)
                return ret;

        /* set i2s data format */
        switch (params_width(params)) {
        case 16:
                if (sgtl5000->fmt == SND_SOC_DAIFMT_RIGHT_J)
                        return -EINVAL;
                i2s_ctl |= SGTL5000_I2S_DLEN_16 << SGTL5000_I2S_DLEN_SHIFT;
                i2s_ctl |= SGTL5000_I2S_SCLKFREQ_32FS <<
                    SGTL5000_I2S_SCLKFREQ_SHIFT;
                break;
        case 20:
                i2s_ctl |= SGTL5000_I2S_DLEN_20 << SGTL5000_I2S_DLEN_SHIFT;
                i2s_ctl |= SGTL5000_I2S_SCLKFREQ_64FS <<
                    SGTL5000_I2S_SCLKFREQ_SHIFT;
                break;
        case 24:
                i2s_ctl |= SGTL5000_I2S_DLEN_24 << SGTL5000_I2S_DLEN_SHIFT;
                i2s_ctl |= SGTL5000_I2S_SCLKFREQ_64FS <<
                    SGTL5000_I2S_SCLKFREQ_SHIFT;
                break;
        case 32:
                if (sgtl5000->fmt == SND_SOC_DAIFMT_RIGHT_J)
                        return -EINVAL;
                i2s_ctl |= SGTL5000_I2S_DLEN_32 << SGTL5000_I2S_DLEN_SHIFT;
                i2s_ctl |= SGTL5000_I2S_SCLKFREQ_64FS <<
                    SGTL5000_I2S_SCLKFREQ_SHIFT;
                break;
        default:
                return -EINVAL;
        }

        snd_soc_component_update_bits(component, SGTL5000_CHIP_I2S_CTRL,
                            SGTL5000_I2S_DLEN_MASK | SGTL5000_I2S_SCLKFREQ_MASK,
                            i2s_ctl);

        return 0;
}

/*
 * set dac bias
 * common state changes:
 * startup:
 * off --> standby --> prepare --> on
 * standby --> prepare --> on
 *
 * stop:
 * on --> prepare --> standby
 */
static int sgtl5000_set_bias_level(struct snd_soc_component *component,
                                   enum snd_soc_bias_level level)
{
        struct sgtl5000_priv *sgtl = snd_soc_component_get_drvdata(component);
        int ret;

        switch (level) {
        case SND_SOC_BIAS_ON:
        case SND_SOC_BIAS_PREPARE:
        case SND_SOC_BIAS_STANDBY:
                regcache_cache_only(sgtl->regmap, false);
                ret = regcache_sync(sgtl->regmap);
                if (ret) {
                        regcache_cache_only(sgtl->regmap, true);
                        return ret;
                }

                snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER,
                                    SGTL5000_REFTOP_POWERUP,
                                    SGTL5000_REFTOP_POWERUP);
                break;
        case SND_SOC_BIAS_OFF:
                regcache_cache_only(sgtl->regmap, true);
                snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER,
                                    SGTL5000_REFTOP_POWERUP, 0);
                break;
        }

        return 0;
}

#define SGTL5000_FORMATS (SNDRV_PCM_FMTBIT_S16_LE |\
                        SNDRV_PCM_FMTBIT_S20_3LE |\
                        SNDRV_PCM_FMTBIT_S24_LE |\
                        SNDRV_PCM_FMTBIT_S32_LE)

static const struct snd_soc_dai_ops sgtl5000_ops = {
        .hw_params = sgtl5000_pcm_hw_params,
        .mute_stream = sgtl5000_mute_stream,
        .set_fmt = sgtl5000_set_dai_fmt,
        .set_sysclk = sgtl5000_set_dai_sysclk,
        .no_capture_mute = 1,
};

static struct snd_soc_dai_driver sgtl5000_dai = {
        .name = "sgtl5000",
        .playback = {
                .stream_name = "Playback",
                .channels_min = 1,
                .channels_max = 2,
                /*
                 * only support 8~48K + 96K,
                 * TODO modify hw_param to support more
                 */
                .rates = SNDRV_PCM_RATE_8000_48000 | SNDRV_PCM_RATE_96000,
                .formats = SGTL5000_FORMATS,
        },
        .capture = {
                .stream_name = "Capture",
                .channels_min = 1,
                .channels_max = 2,
                .rates = SNDRV_PCM_RATE_8000_48000 | SNDRV_PCM_RATE_96000,
                .formats = SGTL5000_FORMATS,
        },
        .ops = &sgtl5000_ops,
        .symmetric_rate = 1,
};

static bool sgtl5000_volatile(struct device *dev, unsigned int reg)
{
        switch (reg) {
        case SGTL5000_CHIP_ID:
        case SGTL5000_CHIP_ADCDAC_CTRL:
        case SGTL5000_CHIP_ANA_STATUS:
                return true;
        }

        return false;
}

static bool sgtl5000_readable(struct device *dev, unsigned int reg)
{
        switch (reg) {
        case SGTL5000_CHIP_ID:
        case SGTL5000_CHIP_DIG_POWER:
        case SGTL5000_CHIP_CLK_CTRL:
        case SGTL5000_CHIP_I2S_CTRL:
        case SGTL5000_CHIP_SSS_CTRL:
        case SGTL5000_CHIP_ADCDAC_CTRL:
        case SGTL5000_CHIP_DAC_VOL:
        case SGTL5000_CHIP_PAD_STRENGTH:
        case SGTL5000_CHIP_ANA_ADC_CTRL:
        case SGTL5000_CHIP_ANA_HP_CTRL:
        case SGTL5000_CHIP_ANA_CTRL:
        case SGTL5000_CHIP_LINREG_CTRL:
        case SGTL5000_CHIP_REF_CTRL:
        case SGTL5000_CHIP_MIC_CTRL:
        case SGTL5000_CHIP_LINE_OUT_CTRL:
        case SGTL5000_CHIP_LINE_OUT_VOL:
        case SGTL5000_CHIP_ANA_POWER:
        case SGTL5000_CHIP_PLL_CTRL:
        case SGTL5000_CHIP_CLK_TOP_CTRL:
        case SGTL5000_CHIP_ANA_STATUS:
        case SGTL5000_CHIP_SHORT_CTRL:
        case SGTL5000_CHIP_ANA_TEST2:
        case SGTL5000_DAP_CTRL:
        case SGTL5000_DAP_PEQ:
        case SGTL5000_DAP_BASS_ENHANCE:
        case SGTL5000_DAP_BASS_ENHANCE_CTRL:
        case SGTL5000_DAP_AUDIO_EQ:
        case SGTL5000_DAP_SURROUND:
        case SGTL5000_DAP_FLT_COEF_ACCESS:
        case SGTL5000_DAP_COEF_WR_B0_MSB:
        case SGTL5000_DAP_COEF_WR_B0_LSB:
        case SGTL5000_DAP_EQ_BASS_BAND0:
        case SGTL5000_DAP_EQ_BASS_BAND1:
        case SGTL5000_DAP_EQ_BASS_BAND2:
        case SGTL5000_DAP_EQ_BASS_BAND3:
        case SGTL5000_DAP_EQ_BASS_BAND4:
        case SGTL5000_DAP_MAIN_CHAN:
        case SGTL5000_DAP_MIX_CHAN:
        case SGTL5000_DAP_AVC_CTRL:
        case SGTL5000_DAP_AVC_THRESHOLD:
        case SGTL5000_DAP_AVC_ATTACK:
        case SGTL5000_DAP_AVC_DECAY:
        case SGTL5000_DAP_COEF_WR_B1_MSB:
        case SGTL5000_DAP_COEF_WR_B1_LSB:
        case SGTL5000_DAP_COEF_WR_B2_MSB:
        case SGTL5000_DAP_COEF_WR_B2_LSB:
        case SGTL5000_DAP_COEF_WR_A1_MSB:
        case SGTL5000_DAP_COEF_WR_A1_LSB:
        case SGTL5000_DAP_COEF_WR_A2_MSB:
        case SGTL5000_DAP_COEF_WR_A2_LSB:
                return true;

        default:
                return false;
        }
}

/*
 * This precalculated table contains all (vag_val * 100 / lo_calcntrl) results
 * to select an appropriate lo_vol_* in SGTL5000_CHIP_LINE_OUT_VOL
 * The calculatation was done for all possible register values which
 * is the array index and the following formula: 10^((idx−15)/40) * 100
 */
static const u8 vol_quot_table[] = {
        42, 45, 47, 50, 53, 56, 60, 63,
        67, 71, 75, 79, 84, 89, 94, 100,
        106, 112, 119, 126, 133, 141, 150, 158,
        168, 178, 188, 200, 211, 224, 237, 251
};

/*
 * sgtl5000 has 3 internal power supplies:
 * 1. VAG, normally set to vdda/2
 * 2. charge pump, set to different value
 *      according to voltage of vdda and vddio
 * 3. line out VAG, normally set to vddio/2
 *
 * and should be set according to:
 * 1. vddd provided by external or not
 * 2. vdda and vddio voltage value. > 3.1v or not
 */
static int sgtl5000_set_power_regs(struct snd_soc_component *component)
{
        int vddd;
        int vdda;
        int vddio;
        u16 ana_pwr;
        u16 lreg_ctrl;
        int vag;
        int lo_vag;
        int vol_quot;
        int lo_vol;
        size_t i;
        struct sgtl5000_priv *sgtl5000 = snd_soc_component_get_drvdata(component);

        vdda  = regulator_get_voltage(sgtl5000->supplies[VDDA].consumer);
        vddio = regulator_get_voltage(sgtl5000->supplies[VDDIO].consumer);
        vddd  = (sgtl5000->num_supplies > VDDD)
                ? regulator_get_voltage(sgtl5000->supplies[VDDD].consumer)
                : LDO_VOLTAGE;

        vdda  = vdda / 1000;
        vddio = vddio / 1000;
        vddd  = vddd / 1000;

        if (vdda <= 0 || vddio <= 0 || vddd < 0) {
                dev_err(component->dev, "regulator voltage not set correctly\n");

                return -EINVAL;
        }

        /* according to datasheet, maximum voltage of supplies */
        if (vdda > 3600 || vddio > 3600 || vddd > 1980) {
                dev_err(component->dev,
                        "exceed max voltage vdda %dmV vddio %dmV vddd %dmV\n",
                        vdda, vddio, vddd);

                return -EINVAL;
        }

        /* reset value */
        ana_pwr = snd_soc_component_read(component, SGTL5000_CHIP_ANA_POWER);
        ana_pwr |= SGTL5000_DAC_STEREO |
                        SGTL5000_ADC_STEREO |
                        SGTL5000_REFTOP_POWERUP;
        lreg_ctrl = snd_soc_component_read(component, SGTL5000_CHIP_LINREG_CTRL);

        if (vddio < 3100 && vdda < 3100) {
                /* enable internal oscillator used for charge pump */
                snd_soc_component_update_bits(component, SGTL5000_CHIP_CLK_TOP_CTRL,
                                        SGTL5000_INT_OSC_EN,
                                        SGTL5000_INT_OSC_EN);
                /* Enable VDDC charge pump */
                ana_pwr |= SGTL5000_VDDC_CHRGPMP_POWERUP;
        } else {
                ana_pwr &= ~SGTL5000_VDDC_CHRGPMP_POWERUP;
                /*
                 * if vddio == vdda the source of charge pump should be
                 * assigned manually to VDDIO
                 */
                if (regulator_is_equal(sgtl5000->supplies[VDDA].consumer,
                                       sgtl5000->supplies[VDDIO].consumer)) {
                        lreg_ctrl |= SGTL5000_VDDC_ASSN_OVRD;
                        lreg_ctrl |= SGTL5000_VDDC_MAN_ASSN_VDDIO <<
                                    SGTL5000_VDDC_MAN_ASSN_SHIFT;
                }
        }

        snd_soc_component_write(component, SGTL5000_CHIP_LINREG_CTRL, lreg_ctrl);

        snd_soc_component_write(component, SGTL5000_CHIP_ANA_POWER, ana_pwr);

        /*
         * set ADC/DAC VAG to vdda / 2,
         * should stay in range (0.8v, 1.575v)
         */
        vag = vdda / 2;
        if (vag <= SGTL5000_ANA_GND_BASE)
                vag = 0;
        else if (vag >= SGTL5000_ANA_GND_BASE + SGTL5000_ANA_GND_STP *
                 (SGTL5000_ANA_GND_MASK >> SGTL5000_ANA_GND_SHIFT))
                vag = SGTL5000_ANA_GND_MASK >> SGTL5000_ANA_GND_SHIFT;
        else
                vag = (vag - SGTL5000_ANA_GND_BASE) / SGTL5000_ANA_GND_STP;

        snd_soc_component_update_bits(component, SGTL5000_CHIP_REF_CTRL,
                        SGTL5000_ANA_GND_MASK, vag << SGTL5000_ANA_GND_SHIFT);

        /* set line out VAG to vddio / 2, in range (0.8v, 1.675v) */
        lo_vag = vddio / 2;
        if (lo_vag <= SGTL5000_LINE_OUT_GND_BASE)
                lo_vag = 0;
        else if (lo_vag >= SGTL5000_LINE_OUT_GND_BASE +
                SGTL5000_LINE_OUT_GND_STP * SGTL5000_LINE_OUT_GND_MAX)
                lo_vag = SGTL5000_LINE_OUT_GND_MAX;
        else
                lo_vag = (lo_vag - SGTL5000_LINE_OUT_GND_BASE) /
                    SGTL5000_LINE_OUT_GND_STP;

        snd_soc_component_update_bits(component, SGTL5000_CHIP_LINE_OUT_CTRL,
                        SGTL5000_LINE_OUT_CURRENT_MASK |
                        SGTL5000_LINE_OUT_GND_MASK,
                        lo_vag << SGTL5000_LINE_OUT_GND_SHIFT |
                        SGTL5000_LINE_OUT_CURRENT_360u <<
                                SGTL5000_LINE_OUT_CURRENT_SHIFT);

        /*
         * Set lineout output level in range (0..31)
         * the same value is used for right and left channel
         *
         * Searching for a suitable index solving this formula:
         * idx = 40 * log10(vag_val / lo_cagcntrl) + 15
         */
        vol_quot = lo_vag ? (vag * 100) / lo_vag : 0;
        lo_vol = 0;
        for (i = 0; i < ARRAY_SIZE(vol_quot_table); i++) {
                if (vol_quot >= vol_quot_table[i])
                        lo_vol = i;
                else
                        break;
        }

        snd_soc_component_update_bits(component, SGTL5000_CHIP_LINE_OUT_VOL,
                SGTL5000_LINE_OUT_VOL_RIGHT_MASK |
                SGTL5000_LINE_OUT_VOL_LEFT_MASK,
                lo_vol << SGTL5000_LINE_OUT_VOL_RIGHT_SHIFT |
                lo_vol << SGTL5000_LINE_OUT_VOL_LEFT_SHIFT);

        return 0;
}

static int sgtl5000_enable_regulators(struct i2c_client *client)
{
        int ret;
        int i;
        int external_vddd = 0;
        struct regulator *vddd;
        struct sgtl5000_priv *sgtl5000 = i2c_get_clientdata(client);

        for (i = 0; i < ARRAY_SIZE(sgtl5000->supplies); i++)
                sgtl5000->supplies[i].supply = supply_names[i];

        vddd = regulator_get_optional(&client->dev, "VDDD");
        if (IS_ERR(vddd)) {
                /* See if it's just not registered yet */
                if (PTR_ERR(vddd) == -EPROBE_DEFER)
                        return -EPROBE_DEFER;
        } else {
                external_vddd = 1;
                regulator_put(vddd);
        }

        sgtl5000->num_supplies = ARRAY_SIZE(sgtl5000->supplies)
                                 - 1 + external_vddd;
        ret = regulator_bulk_get(&client->dev, sgtl5000->num_supplies,
                                 sgtl5000->supplies);
        if (ret)
                return ret;

        ret = regulator_bulk_enable(sgtl5000->num_supplies,
                                    sgtl5000->supplies);
        if (!ret)
                usleep_range(10, 20);
        else
                regulator_bulk_free(sgtl5000->num_supplies,
                                    sgtl5000->supplies);

        return ret;
}

static int sgtl5000_probe(struct snd_soc_component *component)
{
        int ret;
        u16 reg;
        struct sgtl5000_priv *sgtl5000 = snd_soc_component_get_drvdata(component);
        unsigned int zcd_mask = SGTL5000_HP_ZCD_EN | SGTL5000_ADC_ZCD_EN;

        /* power up sgtl5000 */
        ret = sgtl5000_set_power_regs(component);
        if (ret)
                goto err;

        /* enable small pop, introduce 400ms delay in turning off */
        snd_soc_component_update_bits(component, SGTL5000_CHIP_REF_CTRL,
                                SGTL5000_SMALL_POP, SGTL5000_SMALL_POP);

        /* disable short cut detector */
        snd_soc_component_write(component, SGTL5000_CHIP_SHORT_CTRL, 0);

        snd_soc_component_write(component, SGTL5000_CHIP_DIG_POWER,
                        SGTL5000_ADC_EN | SGTL5000_DAC_EN);

        /* enable dac volume ramp by default */
        snd_soc_component_write(component, SGTL5000_CHIP_ADCDAC_CTRL,
                        SGTL5000_DAC_VOL_RAMP_EN |
                        SGTL5000_DAC_MUTE_RIGHT |
                        SGTL5000_DAC_MUTE_LEFT);

        reg = ((sgtl5000->lrclk_strength) << SGTL5000_PAD_I2S_LRCLK_SHIFT |
               (sgtl5000->sclk_strength) << SGTL5000_PAD_I2S_SCLK_SHIFT |
               0x1f);
        snd_soc_component_write(component, SGTL5000_CHIP_PAD_STRENGTH, reg);

        snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_CTRL,
                zcd_mask, zcd_mask);

        snd_soc_component_update_bits(component, SGTL5000_CHIP_MIC_CTRL,
                        SGTL5000_BIAS_R_MASK,
                        sgtl5000->micbias_resistor << SGTL5000_BIAS_R_SHIFT);

        snd_soc_component_update_bits(component, SGTL5000_CHIP_MIC_CTRL,
                        SGTL5000_BIAS_VOLT_MASK,
                        sgtl5000->micbias_voltage << SGTL5000_BIAS_VOLT_SHIFT);
        /*
         * enable DAP Graphic EQ
         * TODO:
         * Add control for changing between PEQ/Tone Control/GEQ
         */
        snd_soc_component_write(component, SGTL5000_DAP_AUDIO_EQ, SGTL5000_DAP_SEL_GEQ);

        /* Unmute DAC after start */
        snd_soc_component_update_bits(component, SGTL5000_CHIP_ADCDAC_CTRL,
                SGTL5000_DAC_MUTE_LEFT | SGTL5000_DAC_MUTE_RIGHT, 0);

        return 0;

err:
        return ret;
}

static int sgtl5000_of_xlate_dai_id(struct snd_soc_component *component,
                                    struct device_node *endpoint)
{
        /* return dai id 0, whatever the endpoint index */
        return 0;
}

static const struct snd_soc_component_driver sgtl5000_driver = {
        .probe                  = sgtl5000_probe,
        .set_bias_level         = sgtl5000_set_bias_level,
        .controls               = sgtl5000_snd_controls,
        .num_controls           = ARRAY_SIZE(sgtl5000_snd_controls),
        .dapm_widgets           = sgtl5000_dapm_widgets,
        .num_dapm_widgets       = ARRAY_SIZE(sgtl5000_dapm_widgets),
        .dapm_routes            = sgtl5000_dapm_routes,
        .num_dapm_routes        = ARRAY_SIZE(sgtl5000_dapm_routes),
        .of_xlate_dai_id        = sgtl5000_of_xlate_dai_id,
        .suspend_bias_off       = 1,
        .idle_bias_on           = 1,
        .use_pmdown_time        = 1,
        .endianness             = 1,
};

static const struct regmap_config sgtl5000_regmap = {
        .reg_bits = 16,
        .val_bits = 16,
        .reg_stride = 2,

        .max_register = SGTL5000_MAX_REG_OFFSET,
        .volatile_reg = sgtl5000_volatile,
        .readable_reg = sgtl5000_readable,

        .cache_type = REGCACHE_RBTREE,
        .reg_defaults = sgtl5000_reg_defaults,
        .num_reg_defaults = ARRAY_SIZE(sgtl5000_reg_defaults),
};

/*
 * Write all the default values from sgtl5000_reg_defaults[] array into the
 * sgtl5000 registers, to make sure we always start with the sane registers
 * values as stated in the datasheet.
 *
 * Since sgtl5000 does not have a reset line, nor a reset command in software,
 * we follow this approach to guarantee we always start from the default values
 * and avoid problems like, not being able to probe after an audio playback
 * followed by a system reset or a 'reboot' command in Linux
 */
static void sgtl5000_fill_defaults(struct i2c_client *client)
{
        struct sgtl5000_priv *sgtl5000 = i2c_get_clientdata(client);
        int i, ret, val, index;

        for (i = 0; i < ARRAY_SIZE(sgtl5000_reg_defaults); i++) {
                val = sgtl5000_reg_defaults[i].def;
                index = sgtl5000_reg_defaults[i].reg;
                ret = regmap_write(sgtl5000->regmap, index, val);
                if (ret)
                        dev_err(&client->dev,
                                "%s: error %d setting reg 0x%02x to 0x%04x\n",
                                __func__, ret, index, val);
        }
}

static int sgtl5000_i2c_probe(struct i2c_client *client)
{
        struct sgtl5000_priv *sgtl5000;
        int ret, reg, rev;
        struct device_node *np = client->dev.of_node;
        u32 value;
        u16 ana_pwr;

        sgtl5000 = devm_kzalloc(&client->dev, sizeof(*sgtl5000), GFP_KERNEL);
        if (!sgtl5000)
                return -ENOMEM;

        i2c_set_clientdata(client, sgtl5000);

        ret = sgtl5000_enable_regulators(client);
        if (ret)
                return ret;

        sgtl5000->regmap = devm_regmap_init_i2c(client, &sgtl5000_regmap);
        if (IS_ERR(sgtl5000->regmap)) {
                ret = PTR_ERR(sgtl5000->regmap);
                dev_err(&client->dev, "Failed to allocate regmap: %d\n", ret);
                goto disable_regs;
        }

        sgtl5000->mclk = devm_clk_get(&client->dev, NULL);
        if (IS_ERR(sgtl5000->mclk)) {
                ret = PTR_ERR(sgtl5000->mclk);
                /* Defer the probe to see if the clk will be provided later */
                if (ret == -ENOENT)
                        ret = -EPROBE_DEFER;

                dev_err_probe(&client->dev, ret, "Failed to get mclock\n");

                goto disable_regs;
        }

        ret = clk_prepare_enable(sgtl5000->mclk);
        if (ret) {
                dev_err(&client->dev, "Error enabling clock %d\n", ret);
                goto disable_regs;
        }

        /* Need 8 clocks before I2C accesses */
        udelay(1);

        /* read chip information */
        ret = regmap_read(sgtl5000->regmap, SGTL5000_CHIP_ID, &reg);
        if (ret) {
                dev_err(&client->dev, "Error reading chip id %d\n", ret);
                goto disable_clk;
        }

        if (((reg & SGTL5000_PARTID_MASK) >> SGTL5000_PARTID_SHIFT) !=
            SGTL5000_PARTID_PART_ID) {
                dev_err(&client->dev,
                        "Device with ID register %x is not a sgtl5000\n", reg);
                ret = -ENODEV;
                goto disable_clk;
        }

        rev = (reg & SGTL5000_REVID_MASK) >> SGTL5000_REVID_SHIFT;
        dev_info(&client->dev, "sgtl5000 revision 0x%x\n", rev);
        sgtl5000->revision = rev;

        /* reconfigure the clocks in case we're using the PLL */
        ret = regmap_write(sgtl5000->regmap,
                           SGTL5000_CHIP_CLK_CTRL,
                           SGTL5000_CHIP_CLK_CTRL_DEFAULT);
        if (ret)
                dev_err(&client->dev,
                        "Error %d initializing CHIP_CLK_CTRL\n", ret);

        /* Mute everything to avoid pop from the following power-up */
        ret = regmap_write(sgtl5000->regmap, SGTL5000_CHIP_ANA_CTRL,
                           SGTL5000_CHIP_ANA_CTRL_DEFAULT);
        if (ret) {
                dev_err(&client->dev,
                        "Error %d muting outputs via CHIP_ANA_CTRL\n", ret);
                goto disable_clk;
        }

        /*
         * If VAG is powered-on (e.g. from previous boot), it would be disabled
         * by the write to ANA_POWER in later steps of the probe code. This
         * may create a loud pop even with all outputs muted. The proper way
         * to circumvent this is disabling the bit first and waiting the proper
         * cool-down time.
         */
        ret = regmap_read(sgtl5000->regmap, SGTL5000_CHIP_ANA_POWER, &value);
        if (ret) {
                dev_err(&client->dev, "Failed to read ANA_POWER: %d\n", ret);
                goto disable_clk;
        }
        if (value & SGTL5000_VAG_POWERUP) {
                ret = regmap_update_bits(sgtl5000->regmap,
                                         SGTL5000_CHIP_ANA_POWER,
                                         SGTL5000_VAG_POWERUP,
                                         0);
                if (ret) {
                        dev_err(&client->dev, "Error %d disabling VAG\n", ret);
                        goto disable_clk;
                }

                msleep(SGTL5000_VAG_POWERDOWN_DELAY);
        }

        /* Follow section 2.2.1.1 of AN3663 */
        ana_pwr = SGTL5000_ANA_POWER_DEFAULT;
        if (sgtl5000->num_supplies <= VDDD) {
                /* internal VDDD at 1.2V */
                ret = regmap_update_bits(sgtl5000->regmap,
                                         SGTL5000_CHIP_LINREG_CTRL,
                                         SGTL5000_LINREG_VDDD_MASK,
                                         LINREG_VDDD);
                if (ret)
                        dev_err(&client->dev,
                                "Error %d setting LINREG_VDDD\n", ret);

                ana_pwr |= SGTL5000_LINEREG_D_POWERUP;
                dev_info(&client->dev,
                         "Using internal LDO instead of VDDD: check ER1 erratum\n");
        } else {
                /* using external LDO for VDDD
                 * Clear startup powerup and simple powerup
                 * bits to save power
                 */
                ana_pwr &= ~(SGTL5000_STARTUP_POWERUP
                             | SGTL5000_LINREG_SIMPLE_POWERUP);
                dev_dbg(&client->dev, "Using external VDDD\n");
        }
        ret = regmap_write(sgtl5000->regmap, SGTL5000_CHIP_ANA_POWER, ana_pwr);
        if (ret)
                dev_err(&client->dev,
                        "Error %d setting CHIP_ANA_POWER to %04x\n",
                        ret, ana_pwr);

        if (np) {
                if (!of_property_read_u32(np,
                        "micbias-resistor-k-ohms", &value)) {
                        switch (value) {
                        case SGTL5000_MICBIAS_OFF:
                                sgtl5000->micbias_resistor = 0;
                                break;
                        case SGTL5000_MICBIAS_2K:
                                sgtl5000->micbias_resistor = 1;
                                break;
                        case SGTL5000_MICBIAS_4K:
                                sgtl5000->micbias_resistor = 2;
                                break;
                        case SGTL5000_MICBIAS_8K:
                                sgtl5000->micbias_resistor = 3;
                                break;
                        default:
                                sgtl5000->micbias_resistor = 2;
                                dev_err(&client->dev,
                                        "Unsuitable MicBias resistor\n");
                        }
                } else {
                        /* default is 4Kohms */
                        sgtl5000->micbias_resistor = 2;
                }
                if (!of_property_read_u32(np,
                        "micbias-voltage-m-volts", &value)) {
                        /* 1250mV => 0 */
                        /* steps of 250mV */
                        if ((value >= 1250) && (value <= 3000))
                                sgtl5000->micbias_voltage = (value / 250) - 5;
                        else {
                                sgtl5000->micbias_voltage = 0;
                                dev_err(&client->dev,
                                        "Unsuitable MicBias voltage\n");
                        }
                } else {
                        sgtl5000->micbias_voltage = 0;
                }
        }

        sgtl5000->lrclk_strength = I2S_LRCLK_STRENGTH_LOW;
        if (!of_property_read_u32(np, "lrclk-strength", &value)) {
                if (value > I2S_LRCLK_STRENGTH_HIGH)
                        value = I2S_LRCLK_STRENGTH_LOW;
                sgtl5000->lrclk_strength = value;
        }

        sgtl5000->sclk_strength = I2S_SCLK_STRENGTH_LOW;
        if (!of_property_read_u32(np, "sclk-strength", &value)) {
                if (value > I2S_SCLK_STRENGTH_HIGH)
                        value = I2S_SCLK_STRENGTH_LOW;
                sgtl5000->sclk_strength = value;
        }

        /* Ensure sgtl5000 will start with sane register values */
        sgtl5000_fill_defaults(client);

        ret = devm_snd_soc_register_component(&client->dev,
                        &sgtl5000_driver, &sgtl5000_dai, 1);
        if (ret)
                goto disable_clk;

        return 0;

disable_clk:
        clk_disable_unprepare(sgtl5000->mclk);

disable_regs:
        regulator_bulk_disable(sgtl5000->num_supplies, sgtl5000->supplies);
        regulator_bulk_free(sgtl5000->num_supplies, sgtl5000->supplies);

        return ret;
}

static void sgtl5000_i2c_remove(struct i2c_client *client)
{
        struct sgtl5000_priv *sgtl5000 = i2c_get_clientdata(client);

        regmap_write(sgtl5000->regmap, SGTL5000_CHIP_CLK_CTRL, SGTL5000_CHIP_CLK_CTRL_DEFAULT);
        regmap_write(sgtl5000->regmap, SGTL5000_CHIP_DIG_POWER, SGTL5000_DIG_POWER_DEFAULT);
        regmap_write(sgtl5000->regmap, SGTL5000_CHIP_ANA_POWER, SGTL5000_ANA_POWER_DEFAULT);

        clk_disable_unprepare(sgtl5000->mclk);
        regulator_bulk_disable(sgtl5000->num_supplies, sgtl5000->supplies);
        regulator_bulk_free(sgtl5000->num_supplies, sgtl5000->supplies);
}

static void sgtl5000_i2c_shutdown(struct i2c_client *client)
{
        sgtl5000_i2c_remove(client);
}

static const struct i2c_device_id sgtl5000_id[] = {
        {"sgtl5000"},
        {},
};

MODULE_DEVICE_TABLE(i2c, sgtl5000_id);

static const struct of_device_id sgtl5000_dt_ids[] = {
        { .compatible = "fsl,sgtl5000", },
        { /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, sgtl5000_dt_ids);

static struct i2c_driver sgtl5000_i2c_driver = {
        .driver = {
                .name = "sgtl5000",
                .of_match_table = sgtl5000_dt_ids,
        },
        .probe = sgtl5000_i2c_probe,
        .remove = sgtl5000_i2c_remove,
        .shutdown = sgtl5000_i2c_shutdown,
        .id_table = sgtl5000_id,
};

module_i2c_driver(sgtl5000_i2c_driver);

MODULE_DESCRIPTION("Freescale SGTL5000 ALSA SoC Codec Driver");
MODULE_AUTHOR("Zeng Zhaoming <zengzm.kernel@gmail.com>");
MODULE_LICENSE("GPL");