// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * Freescale eSDHC controller driver.
 *
 * Copyright (c) 2007, 2010, 2012 Freescale Semiconductor, Inc.
 * Copyright (c) 2009 MontaVista Software, Inc.
 * Copyright 2020 NXP
 *
 * Authors: Xiaobo Xie <X.Xie@freescale.com>
 *          Anton Vorontsov <avorontsov@ru.mvista.com>
 */

#include <linux/err.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/delay.h>
#include <linux/module.h>
#include <linux/sys_soc.h>
#include <linux/clk.h>
#include <linux/ktime.h>
#include <linux/dma-mapping.h>
#include <linux/iopoll.h>
#include <linux/mmc/host.h>
#include <linux/mmc/mmc.h>
#include "sdhci-pltfm.h"
#include "sdhci-esdhc.h"

#define VENDOR_V_22     0x12
#define VENDOR_V_23     0x13

#define MMC_TIMING_NUM (MMC_TIMING_MMC_HS400 + 1)

struct esdhc_clk_fixup {
        const unsigned int sd_dflt_max_clk;
        const unsigned int max_clk[MMC_TIMING_NUM];
};

static const struct esdhc_clk_fixup ls1021a_esdhc_clk = {
        .sd_dflt_max_clk = 25000000,
        .max_clk[MMC_TIMING_MMC_HS] = 46500000,
        .max_clk[MMC_TIMING_SD_HS] = 46500000,
};

static const struct esdhc_clk_fixup ls1043a_esdhc_clk = {
        .sd_dflt_max_clk = 25000000,
        .max_clk[MMC_TIMING_UHS_SDR104] = 116700000,
        .max_clk[MMC_TIMING_MMC_HS200] = 116700000,
};

static const struct esdhc_clk_fixup ls1046a_esdhc_clk = {
        .sd_dflt_max_clk = 25000000,
        .max_clk[MMC_TIMING_UHS_SDR104] = 167000000,
        .max_clk[MMC_TIMING_MMC_HS200] = 167000000,
};

static const struct esdhc_clk_fixup ls1012a_esdhc_clk = {
        .sd_dflt_max_clk = 25000000,
        .max_clk[MMC_TIMING_UHS_SDR104] = 125000000,
        .max_clk[MMC_TIMING_MMC_HS200] = 125000000,
};

static const struct esdhc_clk_fixup p1010_esdhc_clk = {
        .sd_dflt_max_clk = 20000000,
        .max_clk[MMC_TIMING_LEGACY] = 20000000,
        .max_clk[MMC_TIMING_MMC_HS] = 42000000,
        .max_clk[MMC_TIMING_SD_HS] = 40000000,
};

static const struct of_device_id sdhci_esdhc_of_match[] = {
        { .compatible = "fsl,ls1021a-esdhc", .data = &ls1021a_esdhc_clk},
        { .compatible = "fsl,ls1043a-esdhc", .data = &ls1043a_esdhc_clk},
        { .compatible = "fsl,ls1046a-esdhc", .data = &ls1046a_esdhc_clk},
        { .compatible = "fsl,ls1012a-esdhc", .data = &ls1012a_esdhc_clk},
        { .compatible = "fsl,p1010-esdhc",   .data = &p1010_esdhc_clk},
        { .compatible = "fsl,mpc8379-esdhc" },
        { .compatible = "fsl,mpc8536-esdhc" },
        { .compatible = "fsl,esdhc" },
        { }
};
MODULE_DEVICE_TABLE(of, sdhci_esdhc_of_match);

struct sdhci_esdhc {
        u8 vendor_ver;
        u8 spec_ver;
        bool quirk_incorrect_hostver;
        bool quirk_limited_clk_division;
        bool quirk_unreliable_pulse_detection;
        bool quirk_tuning_erratum_type1;
        bool quirk_tuning_erratum_type2;
        bool quirk_ignore_data_inhibit;
        bool quirk_delay_before_data_reset;
        bool quirk_trans_complete_erratum;
        bool in_sw_tuning;
        unsigned int peripheral_clock;
        const struct esdhc_clk_fixup *clk_fixup;
        u32 div_ratio;
};

/**
 * esdhc_readl_fixup - Fixup the value read from incompatible eSDHC register
 *                     to make it compatible with SD spec.
 *
 * @host: pointer to sdhci_host
 * @spec_reg: SD spec register address
 * @value: 32bit eSDHC register value on spec_reg address
 *
 * In SD spec, there are 8/16/32/64 bits registers, while all of eSDHC
 * registers are 32 bits. There are differences in register size, register
 * address, register function, bit position and function between eSDHC spec
 * and SD spec.
 *
 * Return a fixed up register value
 */
static u32 esdhc_readl_fixup(struct sdhci_host *host,
                                     int spec_reg, u32 value)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
        u32 ret;

        /*
         * The bit of ADMA flag in eSDHC is not compatible with standard
         * SDHC register, so set fake flag SDHCI_CAN_DO_ADMA2 when ADMA is
         * supported by eSDHC.
         * And for many FSL eSDHC controller, the reset value of field
         * SDHCI_CAN_DO_ADMA1 is 1, but some of them can't support ADMA,
         * only these vendor version is greater than 2.2/0x12 support ADMA.
         */
        if ((spec_reg == SDHCI_CAPABILITIES) && (value & SDHCI_CAN_DO_ADMA1)) {
                if (esdhc->vendor_ver > VENDOR_V_22) {
                        ret = value | SDHCI_CAN_DO_ADMA2;
                        return ret;
                }
        }

        /*
         * The DAT[3:0] line signal levels and the CMD line signal level are
         * not compatible with standard SDHC register. The line signal levels
         * DAT[7:0] are at bits 31:24 and the command line signal level is at
         * bit 23. All other bits are the same as in the standard SDHC
         * register.
         */
        if (spec_reg == SDHCI_PRESENT_STATE) {
                ret = value & 0x000fffff;
                ret |= (value >> 4) & SDHCI_DATA_LVL_MASK;
                ret |= (value << 1) & SDHCI_CMD_LVL;

                /*
                 * Some controllers have unreliable Data Line Active
                 * bit for commands with busy signal. This affects
                 * Command Inhibit (data) bit. Just ignore it since
                 * MMC core driver has already polled card status
                 * with CMD13 after any command with busy siganl.
                 */
                if (esdhc->quirk_ignore_data_inhibit)
                        ret &= ~SDHCI_DATA_INHIBIT;
                return ret;
        }

        /*
         * DTS properties of mmc host are used to enable each speed mode
         * according to soc and board capability. So clean up
         * SDR50/SDR104/DDR50 support bits here.
         */
        if (spec_reg == SDHCI_CAPABILITIES_1) {
                ret = value & ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_SDR104 |
                                SDHCI_SUPPORT_DDR50);
                return ret;
        }

        ret = value;
        return ret;
}

static u16 esdhc_readw_fixup(struct sdhci_host *host,
                                     int spec_reg, u32 value)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
        u16 ret;
        int shift = (spec_reg & 0x2) * 8;

        if (spec_reg == SDHCI_TRANSFER_MODE)
                return pltfm_host->xfer_mode_shadow;

        if (spec_reg == SDHCI_HOST_VERSION)
                ret = value & 0xffff;
        else
                ret = (value >> shift) & 0xffff;
        /* Workaround for T4240-R1.0-R2.0 eSDHC which has incorrect
         * vendor version and spec version information.
         */
        if ((spec_reg == SDHCI_HOST_VERSION) &&
            (esdhc->quirk_incorrect_hostver))
                ret = (VENDOR_V_23 << SDHCI_VENDOR_VER_SHIFT) | SDHCI_SPEC_200;
        return ret;
}

static u8 esdhc_readb_fixup(struct sdhci_host *host,
                                     int spec_reg, u32 value)
{
        u8 ret;
        u8 dma_bits;
        int shift = (spec_reg & 0x3) * 8;

        ret = (value >> shift) & 0xff;

        /*
         * "DMA select" locates at offset 0x28 in SD specification, but on
         * P5020 or P3041, it locates at 0x29.
         */
        if (spec_reg == SDHCI_HOST_CONTROL) {
                /* DMA select is 22,23 bits in Protocol Control Register */
                dma_bits = (value >> 5) & SDHCI_CTRL_DMA_MASK;
                /* fixup the result */
                ret &= ~SDHCI_CTRL_DMA_MASK;
                ret |= dma_bits;
        }
        return ret;
}

/**
 * esdhc_writel_fixup - Fixup the SD spec register value so that it could be
 *                      written into eSDHC register.
 *
 * @host: pointer to sdhci_host
 * @spec_reg: SD spec register address
 * @value: 8/16/32bit SD spec register value that would be written
 * @old_value: 32bit eSDHC register value on spec_reg address
 *
 * In SD spec, there are 8/16/32/64 bits registers, while all of eSDHC
 * registers are 32 bits. There are differences in register size, register
 * address, register function, bit position and function between eSDHC spec
 * and SD spec.
 *
 * Return a fixed up register value
 */
static u32 esdhc_writel_fixup(struct sdhci_host *host,
                                     int spec_reg, u32 value, u32 old_value)
{
        u32 ret;

        /*
         * Enabling IRQSTATEN[BGESEN] is just to set IRQSTAT[BGE]
         * when SYSCTL[RSTD] is set for some special operations.
         * No any impact on other operation.
         */
        if (spec_reg == SDHCI_INT_ENABLE)
                ret = value | SDHCI_INT_BLK_GAP;
        else
                ret = value;

        return ret;
}

static u32 esdhc_writew_fixup(struct sdhci_host *host,
                                     int spec_reg, u16 value, u32 old_value)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        int shift = (spec_reg & 0x2) * 8;
        u32 ret;

        switch (spec_reg) {
        case SDHCI_TRANSFER_MODE:
                /*
                 * Postpone this write, we must do it together with a
                 * command write that is down below. Return old value.
                 */
                pltfm_host->xfer_mode_shadow = value;
                return old_value;
        case SDHCI_COMMAND:
                ret = (value << 16) | pltfm_host->xfer_mode_shadow;
                return ret;
        }

        ret = old_value & (~(0xffff << shift));
        ret |= (value << shift);

        if (spec_reg == SDHCI_BLOCK_SIZE) {
                /*
                 * Two last DMA bits are reserved, and first one is used for
                 * non-standard blksz of 4096 bytes that we don't support
                 * yet. So clear the DMA boundary bits.
                 */
                ret &= (~SDHCI_MAKE_BLKSZ(0x7, 0));
        }
        return ret;
}

static u32 esdhc_writeb_fixup(struct sdhci_host *host,
                                     int spec_reg, u8 value, u32 old_value)
{
        u32 ret;
        u32 dma_bits;
        u8 tmp;
        int shift = (spec_reg & 0x3) * 8;

        /*
         * eSDHC doesn't have a standard power control register, so we do
         * nothing here to avoid incorrect operation.
         */
        if (spec_reg == SDHCI_POWER_CONTROL)
                return old_value;
        /*
         * "DMA select" location is offset 0x28 in SD specification, but on
         * P5020 or P3041, it's located at 0x29.
         */
        if (spec_reg == SDHCI_HOST_CONTROL) {
                /*
                 * If host control register is not standard, exit
                 * this function
                 */
                if (host->quirks2 & SDHCI_QUIRK2_BROKEN_HOST_CONTROL)
                        return old_value;

                /* DMA select is 22,23 bits in Protocol Control Register */
                dma_bits = (value & SDHCI_CTRL_DMA_MASK) << 5;
                ret = (old_value & (~(SDHCI_CTRL_DMA_MASK << 5))) | dma_bits;
                tmp = (value & (~SDHCI_CTRL_DMA_MASK)) |
                      (old_value & SDHCI_CTRL_DMA_MASK);
                ret = (ret & (~0xff)) | tmp;

                /* Prevent SDHCI core from writing reserved bits (e.g. HISPD) */
                ret &= ~ESDHC_HOST_CONTROL_RES;
                return ret;
        }

        ret = (old_value & (~(0xff << shift))) | (value << shift);
        return ret;
}

static u32 esdhc_be_readl(struct sdhci_host *host, int reg)
{
        u32 ret;
        u32 value;

        if (reg == SDHCI_CAPABILITIES_1)
                value = ioread32be(host->ioaddr + ESDHC_CAPABILITIES_1);
        else
                value = ioread32be(host->ioaddr + reg);

        ret = esdhc_readl_fixup(host, reg, value);

        return ret;
}

static u32 esdhc_le_readl(struct sdhci_host *host, int reg)
{
        u32 ret;
        u32 value;

        if (reg == SDHCI_CAPABILITIES_1)
                value = ioread32(host->ioaddr + ESDHC_CAPABILITIES_1);
        else
                value = ioread32(host->ioaddr + reg);

        ret = esdhc_readl_fixup(host, reg, value);

        return ret;
}

static u16 esdhc_be_readw(struct sdhci_host *host, int reg)
{
        u16 ret;
        u32 value;
        int base = reg & ~0x3;

        value = ioread32be(host->ioaddr + base);
        ret = esdhc_readw_fixup(host, reg, value);
        return ret;
}

static u16 esdhc_le_readw(struct sdhci_host *host, int reg)
{
        u16 ret;
        u32 value;
        int base = reg & ~0x3;

        value = ioread32(host->ioaddr + base);
        ret = esdhc_readw_fixup(host, reg, value);
        return ret;
}

static u8 esdhc_be_readb(struct sdhci_host *host, int reg)
{
        u8 ret;
        u32 value;
        int base = reg & ~0x3;

        value = ioread32be(host->ioaddr + base);
        ret = esdhc_readb_fixup(host, reg, value);
        return ret;
}

static u8 esdhc_le_readb(struct sdhci_host *host, int reg)
{
        u8 ret;
        u32 value;
        int base = reg & ~0x3;

        value = ioread32(host->ioaddr + base);
        ret = esdhc_readb_fixup(host, reg, value);
        return ret;
}

static void esdhc_be_writel(struct sdhci_host *host, u32 val, int reg)
{
        u32 value;

        value = esdhc_writel_fixup(host, reg, val, 0);
        iowrite32be(value, host->ioaddr + reg);
}

static void esdhc_le_writel(struct sdhci_host *host, u32 val, int reg)
{
        u32 value;

        value = esdhc_writel_fixup(host, reg, val, 0);
        iowrite32(value, host->ioaddr + reg);
}

static void esdhc_be_writew(struct sdhci_host *host, u16 val, int reg)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
        int base = reg & ~0x3;
        u32 value;
        u32 ret;

        value = ioread32be(host->ioaddr + base);
        ret = esdhc_writew_fixup(host, reg, val, value);
        if (reg != SDHCI_TRANSFER_MODE)
                iowrite32be(ret, host->ioaddr + base);

        /* Starting SW tuning requires ESDHC_SMPCLKSEL to be set
         * 1us later after ESDHC_EXTN is set.
         */
        if (base == ESDHC_SYSTEM_CONTROL_2) {
                if (!(value & ESDHC_EXTN) && (ret & ESDHC_EXTN) &&
                    esdhc->in_sw_tuning) {
                        udelay(1);
                        ret |= ESDHC_SMPCLKSEL;
                        iowrite32be(ret, host->ioaddr + base);
                }
        }
}

static void esdhc_le_writew(struct sdhci_host *host, u16 val, int reg)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
        int base = reg & ~0x3;
        u32 value;
        u32 ret;

        value = ioread32(host->ioaddr + base);
        ret = esdhc_writew_fixup(host, reg, val, value);
        if (reg != SDHCI_TRANSFER_MODE)
                iowrite32(ret, host->ioaddr + base);

        /* Starting SW tuning requires ESDHC_SMPCLKSEL to be set
         * 1us later after ESDHC_EXTN is set.
         */
        if (base == ESDHC_SYSTEM_CONTROL_2) {
                if (!(value & ESDHC_EXTN) && (ret & ESDHC_EXTN) &&
                    esdhc->in_sw_tuning) {
                        udelay(1);
                        ret |= ESDHC_SMPCLKSEL;
                        iowrite32(ret, host->ioaddr + base);
                }
        }
}

static void esdhc_be_writeb(struct sdhci_host *host, u8 val, int reg)
{
        int base = reg & ~0x3;
        u32 value;
        u32 ret;

        value = ioread32be(host->ioaddr + base);
        ret = esdhc_writeb_fixup(host, reg, val, value);
        iowrite32be(ret, host->ioaddr + base);
}

static void esdhc_le_writeb(struct sdhci_host *host, u8 val, int reg)
{
        int base = reg & ~0x3;
        u32 value;
        u32 ret;

        value = ioread32(host->ioaddr + base);
        ret = esdhc_writeb_fixup(host, reg, val, value);
        iowrite32(ret, host->ioaddr + base);
}

/*
 * For Abort or Suspend after Stop at Block Gap, ignore the ADMA
 * error(IRQSTAT[ADMAE]) if both Transfer Complete(IRQSTAT[TC])
 * and Block Gap Event(IRQSTAT[BGE]) are also set.
 * For Continue, apply soft reset for data(SYSCTL[RSTD]);
 * and re-issue the entire read transaction from beginning.
 */
static void esdhc_of_adma_workaround(struct sdhci_host *host, u32 intmask)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
        bool applicable;
        dma_addr_t dmastart;
        dma_addr_t dmanow;

        applicable = (intmask & SDHCI_INT_DATA_END) &&
                     (intmask & SDHCI_INT_BLK_GAP) &&
                     (esdhc->vendor_ver == VENDOR_V_23);
        if (!applicable)
                return;

        host->data->error = 0;
        dmastart = sg_dma_address(host->data->sg);
        dmanow = dmastart + host->data->bytes_xfered;
        /*
         * Force update to the next DMA block boundary.
         */
        dmanow = (dmanow & ~(SDHCI_DEFAULT_BOUNDARY_SIZE - 1)) +
                SDHCI_DEFAULT_BOUNDARY_SIZE;
        host->data->bytes_xfered = dmanow - dmastart;
        sdhci_writel(host, dmanow, SDHCI_DMA_ADDRESS);
}

static int esdhc_of_enable_dma(struct sdhci_host *host)
{
        int ret;
        u32 value;
        struct device *dev = mmc_dev(host->mmc);

        if (of_device_is_compatible(dev->of_node, "fsl,ls1043a-esdhc") ||
            of_device_is_compatible(dev->of_node, "fsl,ls1046a-esdhc")) {
                ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(40));
                if (ret)
                        return ret;
        }

        value = sdhci_readl(host, ESDHC_DMA_SYSCTL);

        if (of_dma_is_coherent(dev->of_node))
                value |= ESDHC_DMA_SNOOP;
        else
                value &= ~ESDHC_DMA_SNOOP;

        sdhci_writel(host, value, ESDHC_DMA_SYSCTL);
        return 0;
}

static unsigned int esdhc_of_get_max_clock(struct sdhci_host *host)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);

        if (esdhc->peripheral_clock)
                return esdhc->peripheral_clock;
        else
                return pltfm_host->clock;
}

static unsigned int esdhc_of_get_min_clock(struct sdhci_host *host)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
        unsigned int clock;

        if (esdhc->peripheral_clock)
                clock = esdhc->peripheral_clock;
        else
                clock = pltfm_host->clock;
        return clock / 256 / 16;
}

static void esdhc_clock_enable(struct sdhci_host *host, bool enable)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
        ktime_t timeout;
        u32 val, clk_en;

        clk_en = ESDHC_CLOCK_SDCLKEN;

        /*
         * IPGEN/HCKEN/PEREN bits exist on eSDHC whose vendor version
         * is 2.2 or lower.
         */
        if (esdhc->vendor_ver <= VENDOR_V_22)
                clk_en |= (ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN |
                           ESDHC_CLOCK_PEREN);

        val = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);

        if (enable)
                val |= clk_en;
        else
                val &= ~clk_en;

        sdhci_writel(host, val, ESDHC_SYSTEM_CONTROL);

        /*
         * Wait max 20 ms. If vendor version is 2.2 or lower, do not
         * wait clock stable bit which does not exist.
         */
        timeout = ktime_add_ms(ktime_get(), 20);
        while (esdhc->vendor_ver > VENDOR_V_22) {
                bool timedout = ktime_after(ktime_get(), timeout);

                if (sdhci_readl(host, ESDHC_PRSSTAT) & ESDHC_CLOCK_STABLE)
                        break;
                if (timedout) {
                        pr_err("%s: Internal clock never stabilised.\n",
                                mmc_hostname(host->mmc));
                        break;
                }
                usleep_range(10, 20);
        }
}

static void esdhc_flush_async_fifo(struct sdhci_host *host)
{
        ktime_t timeout;
        u32 val;

        val = sdhci_readl(host, ESDHC_DMA_SYSCTL);
        val |= ESDHC_FLUSH_ASYNC_FIFO;
        sdhci_writel(host, val, ESDHC_DMA_SYSCTL);

        /* Wait max 20 ms */
        timeout = ktime_add_ms(ktime_get(), 20);
        while (1) {
                bool timedout = ktime_after(ktime_get(), timeout);

                if (!(sdhci_readl(host, ESDHC_DMA_SYSCTL) &
                      ESDHC_FLUSH_ASYNC_FIFO))
                        break;
                if (timedout) {
                        pr_err("%s: flushing asynchronous FIFO timeout.\n",
                                mmc_hostname(host->mmc));
                        break;
                }
                usleep_range(10, 20);
        }
}

static void esdhc_of_set_clock(struct sdhci_host *host, unsigned int clock)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
        unsigned int pre_div = 1, div = 1;
        unsigned int clock_fixup = 0;
        ktime_t timeout;
        u32 temp;

        if (clock == 0) {
                host->mmc->actual_clock = 0;
                esdhc_clock_enable(host, false);
                return;
        }

        /* Start pre_div at 2 for vendor version < 2.3. */
        if (esdhc->vendor_ver < VENDOR_V_23)
                pre_div = 2;

        /* Fix clock value. */
        if (host->mmc->card && mmc_card_sd(host->mmc->card) &&
            esdhc->clk_fixup && host->mmc->ios.timing == MMC_TIMING_LEGACY)
                clock_fixup = esdhc->clk_fixup->sd_dflt_max_clk;
        else if (esdhc->clk_fixup)
                clock_fixup = esdhc->clk_fixup->max_clk[host->mmc->ios.timing];

        if (clock_fixup == 0 || clock < clock_fixup)
                clock_fixup = clock;

        /* Calculate pre_div and div. */
        while (host->max_clk / pre_div / 16 > clock_fixup && pre_div < 256)
                pre_div *= 2;

        while (host->max_clk / pre_div / div > clock_fixup && div < 16)
                div++;

        esdhc->div_ratio = pre_div * div;

        /* Limit clock division for HS400 200MHz clock for quirk. */
        if (esdhc->quirk_limited_clk_division &&
            clock == MMC_HS200_MAX_DTR &&
            (host->mmc->ios.timing == MMC_TIMING_MMC_HS400 ||
             host->flags & SDHCI_HS400_TUNING)) {
                if (esdhc->div_ratio <= 4) {
                        pre_div = 4;
                        div = 1;
                } else if (esdhc->div_ratio <= 8) {
                        pre_div = 4;
                        div = 2;
                } else if (esdhc->div_ratio <= 12) {
                        pre_div = 4;
                        div = 3;
                } else {
                        pr_warn("%s: using unsupported clock division.\n",
                                mmc_hostname(host->mmc));
                }
                esdhc->div_ratio = pre_div * div;
        }

        host->mmc->actual_clock = host->max_clk / esdhc->div_ratio;

        dev_dbg(mmc_dev(host->mmc), "desired SD clock: %d, actual: %d\n",
                clock, host->mmc->actual_clock);

        /* Set clock division into register. */
        pre_div >>= 1;
        div--;

        esdhc_clock_enable(host, false);

        temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
        temp &= ~ESDHC_CLOCK_MASK;
        temp |= ((div << ESDHC_DIVIDER_SHIFT) |
                (pre_div << ESDHC_PREDIV_SHIFT));
        sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);

        /*
         * Wait max 20 ms. If vendor version is 2.2 or lower, do not
         * wait clock stable bit which does not exist.
         */
        timeout = ktime_add_ms(ktime_get(), 20);
        while (esdhc->vendor_ver > VENDOR_V_22) {
                bool timedout = ktime_after(ktime_get(), timeout);

                if (sdhci_readl(host, ESDHC_PRSSTAT) & ESDHC_CLOCK_STABLE)
                        break;
                if (timedout) {
                        pr_err("%s: Internal clock never stabilised.\n",
                                mmc_hostname(host->mmc));
                        break;
                }
                usleep_range(10, 20);
        }

        /* Additional setting for HS400. */
        if (host->mmc->ios.timing == MMC_TIMING_MMC_HS400 &&
            clock == MMC_HS200_MAX_DTR) {
                temp = sdhci_readl(host, ESDHC_TBCTL);
                sdhci_writel(host, temp | ESDHC_HS400_MODE, ESDHC_TBCTL);
                temp = sdhci_readl(host, ESDHC_SDCLKCTL);
                sdhci_writel(host, temp | ESDHC_CMD_CLK_CTL, ESDHC_SDCLKCTL);
                esdhc_clock_enable(host, true);

                temp = sdhci_readl(host, ESDHC_DLLCFG0);
                temp |= ESDHC_DLL_ENABLE;
                if (host->mmc->actual_clock == MMC_HS200_MAX_DTR)
                        temp |= ESDHC_DLL_FREQ_SEL;
                sdhci_writel(host, temp, ESDHC_DLLCFG0);

                temp |= ESDHC_DLL_RESET;
                sdhci_writel(host, temp, ESDHC_DLLCFG0);
                udelay(1);
                temp &= ~ESDHC_DLL_RESET;
                sdhci_writel(host, temp, ESDHC_DLLCFG0);

                /* Wait max 20 ms */
                if (read_poll_timeout(sdhci_readl, temp,
                                      temp & ESDHC_DLL_STS_SLV_LOCK,
                                      10, 20000, false,
                                      host, ESDHC_DLLSTAT0))
                        pr_err("%s: timeout for delay chain lock.\n",
                               mmc_hostname(host->mmc));

                temp = sdhci_readl(host, ESDHC_TBCTL);
                sdhci_writel(host, temp | ESDHC_HS400_WNDW_ADJUST, ESDHC_TBCTL);

                esdhc_clock_enable(host, false);
                esdhc_flush_async_fifo(host);
        }
        esdhc_clock_enable(host, true);
}

static void esdhc_pltfm_set_bus_width(struct sdhci_host *host, int width)
{
        u32 ctrl;

        ctrl = sdhci_readl(host, ESDHC_PROCTL);
        ctrl &= (~ESDHC_CTRL_BUSWIDTH_MASK);
        switch (width) {
        case MMC_BUS_WIDTH_8:
                ctrl |= ESDHC_CTRL_8BITBUS;
                break;

        case MMC_BUS_WIDTH_4:
                ctrl |= ESDHC_CTRL_4BITBUS;
                break;

        default:
                break;
        }

        sdhci_writel(host, ctrl, ESDHC_PROCTL);
}

static void esdhc_reset(struct sdhci_host *host, u8 mask)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
        u32 val, bus_width = 0;

        /*
         * Add delay to make sure all the DMA transfers are finished
         * for quirk.
         */
        if (esdhc->quirk_delay_before_data_reset &&
            (mask & SDHCI_RESET_DATA) &&
            (host->flags & SDHCI_REQ_USE_DMA))
                mdelay(5);

        /*
         * Save bus-width for eSDHC whose vendor version is 2.2
         * or lower for data reset.
         */
        if ((mask & SDHCI_RESET_DATA) &&
            (esdhc->vendor_ver <= VENDOR_V_22)) {
                val = sdhci_readl(host, ESDHC_PROCTL);
                bus_width = val & ESDHC_CTRL_BUSWIDTH_MASK;
        }

        sdhci_reset(host, mask);

        /*
         * Restore bus-width setting and interrupt registers for eSDHC
         * whose vendor version is 2.2 or lower for data reset.
         */
        if ((mask & SDHCI_RESET_DATA) &&
            (esdhc->vendor_ver <= VENDOR_V_22)) {
                val = sdhci_readl(host, ESDHC_PROCTL);
                val &= ~ESDHC_CTRL_BUSWIDTH_MASK;
                val |= bus_width;
                sdhci_writel(host, val, ESDHC_PROCTL);

                sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
                sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
        }

        /*
         * Some bits have to be cleaned manually for eSDHC whose spec
         * version is higher than 3.0 for all reset.
         */
        if ((mask & SDHCI_RESET_ALL) &&
            (esdhc->spec_ver >= SDHCI_SPEC_300)) {
                val = sdhci_readl(host, ESDHC_TBCTL);
                val &= ~ESDHC_TB_EN;
                sdhci_writel(host, val, ESDHC_TBCTL);

                /*
                 * Initialize eSDHC_DLLCFG1[DLL_PD_PULSE_STRETCH_SEL] to
                 * 0 for quirk.
                 */
                if (esdhc->quirk_unreliable_pulse_detection) {
                        val = sdhci_readl(host, ESDHC_DLLCFG1);
                        val &= ~ESDHC_DLL_PD_PULSE_STRETCH_SEL;
                        sdhci_writel(host, val, ESDHC_DLLCFG1);
                }
        }
}

/* The SCFG, Supplemental Configuration Unit, provides SoC specific
 * configuration and status registers for the device. There is a
 * SDHC IO VSEL control register on SCFG for some platforms. It's
 * used to support SDHC IO voltage switching.
 */
static const struct of_device_id scfg_device_ids[] = {
        { .compatible = "fsl,t1040-scfg", },
        { .compatible = "fsl,ls1012a-scfg", },
        { .compatible = "fsl,ls1046a-scfg", },
        {}
};

/* SDHC IO VSEL control register definition */
#define SCFG_SDHCIOVSELCR       0x408
#define SDHCIOVSELCR_TGLEN      0x80000000
#define SDHCIOVSELCR_VSELVAL    0x60000000
#define SDHCIOVSELCR_SDHC_VS    0x00000001

static int esdhc_signal_voltage_switch(struct mmc_host *mmc,
                                       struct mmc_ios *ios)
{
        struct sdhci_host *host = mmc_priv(mmc);
        struct device_node *scfg_node;
        void __iomem *scfg_base = NULL;
        u32 sdhciovselcr;
        u32 val;

        /*
         * Signal Voltage Switching is only applicable for Host Controllers
         * v3.00 and above.
         */
        if (host->version < SDHCI_SPEC_300)
                return 0;

        val = sdhci_readl(host, ESDHC_PROCTL);

        switch (ios->signal_voltage) {
        case MMC_SIGNAL_VOLTAGE_330:
                val &= ~ESDHC_VOLT_SEL;
                sdhci_writel(host, val, ESDHC_PROCTL);
                return 0;
        case MMC_SIGNAL_VOLTAGE_180:
                scfg_node = of_find_matching_node(NULL, scfg_device_ids);
                if (scfg_node)
                        scfg_base = of_iomap(scfg_node, 0);
                of_node_put(scfg_node);
                if (scfg_base) {
                        sdhciovselcr = SDHCIOVSELCR_TGLEN |
                                       SDHCIOVSELCR_VSELVAL;
                        iowrite32be(sdhciovselcr,
                                scfg_base + SCFG_SDHCIOVSELCR);

                        val |= ESDHC_VOLT_SEL;
                        sdhci_writel(host, val, ESDHC_PROCTL);
                        mdelay(5);

                        sdhciovselcr = SDHCIOVSELCR_TGLEN |
                                       SDHCIOVSELCR_SDHC_VS;
                        iowrite32be(sdhciovselcr,
                                scfg_base + SCFG_SDHCIOVSELCR);
                        iounmap(scfg_base);
                } else {
                        val |= ESDHC_VOLT_SEL;
                        sdhci_writel(host, val, ESDHC_PROCTL);
                }
                return 0;
        default:
                return 0;
        }
}

static struct soc_device_attribute soc_tuning_erratum_type1[] = {
        { .family = "QorIQ T1023", },
        { .family = "QorIQ T1040", },
        { .family = "QorIQ T2080", },
        { .family = "QorIQ LS1021A", },
        { /* sentinel */ }
};

static struct soc_device_attribute soc_tuning_erratum_type2[] = {
        { .family = "QorIQ LS1012A", },
        { .family = "QorIQ LS1043A", },
        { .family = "QorIQ LS1046A", },
        { .family = "QorIQ LS1080A", },
        { .family = "QorIQ LS2080A", },
        { .family = "QorIQ LA1575A", },
        { /* sentinel */ }
};

static void esdhc_tuning_block_enable(struct sdhci_host *host, bool enable)
{
        u32 val;

        esdhc_clock_enable(host, false);
        esdhc_flush_async_fifo(host);

        val = sdhci_readl(host, ESDHC_TBCTL);
        if (enable)
                val |= ESDHC_TB_EN;
        else
                val &= ~ESDHC_TB_EN;
        sdhci_writel(host, val, ESDHC_TBCTL);

        esdhc_clock_enable(host, true);
}

static void esdhc_tuning_window_ptr(struct sdhci_host *host, u8 *window_start,
                                    u8 *window_end)
{
        u32 val;

        /* Write TBCTL[11:8]=4'h8 */
        val = sdhci_readl(host, ESDHC_TBCTL);
        val &= ~(0xf << 8);
        val |= 8 << 8;
        sdhci_writel(host, val, ESDHC_TBCTL);

        mdelay(1);

        /* Read TBCTL[31:0] register and rewrite again */
        val = sdhci_readl(host, ESDHC_TBCTL);
        sdhci_writel(host, val, ESDHC_TBCTL);

        mdelay(1);

        /* Read the TBSTAT[31:0] register twice */
        val = sdhci_readl(host, ESDHC_TBSTAT);
        val = sdhci_readl(host, ESDHC_TBSTAT);

        *window_end = val & 0xff;
        *window_start = (val >> 8) & 0xff;
}

static void esdhc_prepare_sw_tuning(struct sdhci_host *host, u8 *window_start,
                                    u8 *window_end)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
        u8 start_ptr, end_ptr;

        if (esdhc->quirk_tuning_erratum_type1) {
                *window_start = 5 * esdhc->div_ratio;
                *window_end = 3 * esdhc->div_ratio;
                return;
        }

        esdhc_tuning_window_ptr(host, &start_ptr, &end_ptr);

        /* Reset data lines by setting ESDHCCTL[RSTD] */
        sdhci_reset(host, SDHCI_RESET_DATA);
        /* Write 32'hFFFF_FFFF to IRQSTAT register */
        sdhci_writel(host, 0xFFFFFFFF, SDHCI_INT_STATUS);

        /* If TBSTAT[15:8]-TBSTAT[7:0] > (4 * div_ratio) + 2
         * or TBSTAT[7:0]-TBSTAT[15:8] > (4 * div_ratio) + 2,
         * then program TBPTR[TB_WNDW_END_PTR] = 4 * div_ratio
         * and program TBPTR[TB_WNDW_START_PTR] = 8 * div_ratio.
         */

        if (abs(start_ptr - end_ptr) > (4 * esdhc->div_ratio + 2)) {
                *window_start = 8 * esdhc->div_ratio;
                *window_end = 4 * esdhc->div_ratio;
        } else {
                *window_start = 5 * esdhc->div_ratio;
                *window_end = 3 * esdhc->div_ratio;
        }
}

static int esdhc_execute_sw_tuning(struct mmc_host *mmc, u32 opcode,
                                   u8 window_start, u8 window_end)
{
        struct sdhci_host *host = mmc_priv(mmc);
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
        u32 val;
        int ret;

        /* Program TBPTR[TB_WNDW_END_PTR] and TBPTR[TB_WNDW_START_PTR] */
        val = ((u32)window_start << ESDHC_WNDW_STRT_PTR_SHIFT) &
              ESDHC_WNDW_STRT_PTR_MASK;
        val |= window_end & ESDHC_WNDW_END_PTR_MASK;
        sdhci_writel(host, val, ESDHC_TBPTR);

        /* Program the software tuning mode by setting TBCTL[TB_MODE]=2'h3 */
        val = sdhci_readl(host, ESDHC_TBCTL);
        val &= ~ESDHC_TB_MODE_MASK;
        val |= ESDHC_TB_MODE_SW;
        sdhci_writel(host, val, ESDHC_TBCTL);

        esdhc->in_sw_tuning = true;
        ret = sdhci_execute_tuning(mmc, opcode);
        esdhc->in_sw_tuning = false;
        return ret;
}

static int esdhc_execute_tuning(struct mmc_host *mmc, u32 opcode)
{
        struct sdhci_host *host = mmc_priv(mmc);
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
        u8 window_start, window_end;
        int ret, retries = 1;
        bool hs400_tuning;
        unsigned int clk;
        u32 val;

        /* For tuning mode, the sd clock divisor value
         * must be larger than 3 according to reference manual.
         */
        clk = esdhc->peripheral_clock / 3;
        if (host->clock > clk)
                esdhc_of_set_clock(host, clk);

        esdhc_tuning_block_enable(host, true);

        /*
         * The eSDHC controller takes the data timeout value into account
         * during tuning. If the SD card is too slow sending the response, the
         * timer will expire and a "Buffer Read Ready" interrupt without data
         * is triggered. This leads to tuning errors.
         *
         * Just set the timeout to the maximum value because the core will
         * already take care of it in sdhci_send_tuning().
         */
        sdhci_writeb(host, 0xe, SDHCI_TIMEOUT_CONTROL);

        hs400_tuning = host->flags & SDHCI_HS400_TUNING;

        do {
                if (esdhc->quirk_limited_clk_division &&
                    hs400_tuning)
                        esdhc_of_set_clock(host, host->clock);

                /* Do HW tuning */
                val = sdhci_readl(host, ESDHC_TBCTL);
                val &= ~ESDHC_TB_MODE_MASK;
                val |= ESDHC_TB_MODE_3;
                sdhci_writel(host, val, ESDHC_TBCTL);

                ret = sdhci_execute_tuning(mmc, opcode);
                if (ret)
                        break;

                /* For type2 affected platforms of the tuning erratum,
                 * tuning may succeed although eSDHC might not have
                 * tuned properly. Need to check tuning window.
                 */
                if (esdhc->quirk_tuning_erratum_type2 &&
                    !host->tuning_err) {
                        esdhc_tuning_window_ptr(host, &window_start,
                                                &window_end);
                        if (abs(window_start - window_end) >
                            (4 * esdhc->div_ratio + 2))
                                host->tuning_err = -EAGAIN;
                }

                /* If HW tuning fails and triggers erratum,
                 * try workaround.
                 */
                ret = host->tuning_err;
                if (ret == -EAGAIN &&
                    (esdhc->quirk_tuning_erratum_type1 ||
                     esdhc->quirk_tuning_erratum_type2)) {
                        /* Recover HS400 tuning flag */
                        if (hs400_tuning)
                                host->flags |= SDHCI_HS400_TUNING;
                        pr_info("%s: Hold on to use fixed sampling clock. Try SW tuning!\n",
                                mmc_hostname(mmc));
                        /* Do SW tuning */
                        esdhc_prepare_sw_tuning(host, &window_start,
                                                &window_end);
                        ret = esdhc_execute_sw_tuning(mmc, opcode,
                                                      window_start,
                                                      window_end);
                        if (ret)
                                break;

                        /* Retry both HW/SW tuning with reduced clock. */
                        ret = host->tuning_err;
                        if (ret == -EAGAIN && retries) {
                                /* Recover HS400 tuning flag */
                                if (hs400_tuning)
                                        host->flags |= SDHCI_HS400_TUNING;

                                clk = host->max_clk / (esdhc->div_ratio + 1);
                                esdhc_of_set_clock(host, clk);
                                pr_info("%s: Hold on to use fixed sampling clock. Try tuning with reduced clock!\n",
                                        mmc_hostname(mmc));
                        } else {
                                break;
                        }
                } else {
                        break;
                }
        } while (retries--);

        if (ret) {
                esdhc_tuning_block_enable(host, false);
        } else if (hs400_tuning) {
                val = sdhci_readl(host, ESDHC_SDTIMNGCTL);
                val |= ESDHC_FLW_CTL_BG;
                sdhci_writel(host, val, ESDHC_SDTIMNGCTL);
        }

        return ret;
}

static void esdhc_set_uhs_signaling(struct sdhci_host *host,
                                   unsigned int timing)
{
        u32 val;

        /*
         * There are specific registers setting for HS400 mode.
         * Clean all of them if controller is in HS400 mode to
         * exit HS400 mode before re-setting any speed mode.
         */
        val = sdhci_readl(host, ESDHC_TBCTL);
        if (val & ESDHC_HS400_MODE) {
                val = sdhci_readl(host, ESDHC_SDTIMNGCTL);
                val &= ~ESDHC_FLW_CTL_BG;
                sdhci_writel(host, val, ESDHC_SDTIMNGCTL);

                val = sdhci_readl(host, ESDHC_SDCLKCTL);
                val &= ~ESDHC_CMD_CLK_CTL;
                sdhci_writel(host, val, ESDHC_SDCLKCTL);

                esdhc_clock_enable(host, false);
                val = sdhci_readl(host, ESDHC_TBCTL);
                val &= ~ESDHC_HS400_MODE;
                sdhci_writel(host, val, ESDHC_TBCTL);
                esdhc_clock_enable(host, true);

                val = sdhci_readl(host, ESDHC_DLLCFG0);
                val &= ~(ESDHC_DLL_ENABLE | ESDHC_DLL_FREQ_SEL);
                sdhci_writel(host, val, ESDHC_DLLCFG0);

                val = sdhci_readl(host, ESDHC_TBCTL);
                val &= ~ESDHC_HS400_WNDW_ADJUST;
                sdhci_writel(host, val, ESDHC_TBCTL);

                esdhc_tuning_block_enable(host, false);
        }

        if (timing == MMC_TIMING_MMC_HS400)
                esdhc_tuning_block_enable(host, true);
        else
                sdhci_set_uhs_signaling(host, timing);
}

static u32 esdhc_irq(struct sdhci_host *host, u32 intmask)
{
        struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
        struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
        u32 command;

        if (esdhc->quirk_trans_complete_erratum) {
                command = SDHCI_GET_CMD(sdhci_readw(host,
                                        SDHCI_COMMAND));
                if (command == MMC_WRITE_MULTIPLE_BLOCK &&
                                sdhci_readw(host, SDHCI_BLOCK_COUNT) &&
                                intmask & SDHCI_INT_DATA_END) {
                        intmask &= ~SDHCI_INT_DATA_END;
                        sdhci_writel(host, SDHCI_INT_DATA_END,
                                        SDHCI_INT_STATUS);
                }
        }
        return intmask;
}

static u32 esdhc_proctl;
static int esdhc_of_suspend(struct device *dev)
{
        struct sdhci_host *host = dev_get_drvdata(dev);

        esdhc_proctl = sdhci_readl(host, SDHCI_HOST_CONTROL);

        if (host->tuning_mode != SDHCI_TUNING_MODE_3)
                mmc_retune_needed(host->mmc);

        return sdhci_suspend_host(host);
}

static int esdhc_of_resume(struct device *dev)
{
        struct sdhci_host *host = dev_get_drvdata(dev);
        int ret = sdhci_resume_host(host);

        if (ret == 0) {
                /* Isn't this already done by sdhci_resume_host() ? --rmk */
                esdhc_of_enable_dma(host);
                sdhci_writel(host, esdhc_proctl, SDHCI_HOST_CONTROL);
        }
        return ret;
}

static DEFINE_SIMPLE_DEV_PM_OPS(esdhc_of_dev_pm_ops, esdhc_of_suspend, esdhc_of_resume);

static const struct sdhci_ops sdhci_esdhc_be_ops = {
        .read_l = esdhc_be_readl,
        .read_w = esdhc_be_readw,
        .read_b = esdhc_be_readb,
        .write_l = esdhc_be_writel,
        .write_w = esdhc_be_writew,
        .write_b = esdhc_be_writeb,
        .set_clock = esdhc_of_set_clock,
        .enable_dma = esdhc_of_enable_dma,
        .get_max_clock = esdhc_of_get_max_clock,
        .get_min_clock = esdhc_of_get_min_clock,
        .adma_workaround = esdhc_of_adma_workaround,
        .set_bus_width = esdhc_pltfm_set_bus_width,
        .reset = esdhc_reset,
        .set_uhs_signaling = esdhc_set_uhs_signaling,
        .irq = esdhc_irq,
};

static const struct sdhci_ops sdhci_esdhc_le_ops = {
        .read_l = esdhc_le_readl,
        .read_w = esdhc_le_readw,
        .read_b = esdhc_le_readb,
        .write_l = esdhc_le_writel,
        .write_w = esdhc_le_writew,
        .write_b = esdhc_le_writeb,
        .set_clock = esdhc_of_set_clock,
        .enable_dma = esdhc_of_enable_dma,
        .get_max_clock = esdhc_of_get_max_clock,
        .get_min_clock = esdhc_of_get_min_clock,
        .adma_workaround = esdhc_of_adma_workaround,
        .set_bus_width = esdhc_pltfm_set_bus_width,
        .reset = esdhc_reset,
        .set_uhs_signaling = esdhc_set_uhs_signaling,
        .irq = esdhc_irq,
};

static const struct sdhci_pltfm_data sdhci_esdhc_be_pdata = {
        .quirks = ESDHC_DEFAULT_QUIRKS |
#ifdef CONFIG_PPC
                  SDHCI_QUIRK_BROKEN_CARD_DETECTION |
#endif
                  SDHCI_QUIRK_NO_CARD_NO_RESET |
                  SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
        .ops = &sdhci_esdhc_be_ops,
};

static const struct sdhci_pltfm_data sdhci_esdhc_le_pdata = {
        .quirks = ESDHC_DEFAULT_QUIRKS |
                  SDHCI_QUIRK_NO_CARD_NO_RESET |
                  SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
        .ops = &sdhci_esdhc_le_ops,
};

static struct soc_device_attribute soc_incorrect_hostver[] = {
        { .family = "QorIQ T4240", .revision = "1.0", },
        { .family = "QorIQ T4240", .revision = "2.0", },
        { /* sentinel */ }
};

static struct soc_device_attribute soc_fixup_sdhc_clkdivs[] = {
        { .family = "QorIQ LX2160A", .revision = "1.0", },
        { .family = "QorIQ LX2160A", .revision = "2.0", },
        { .family = "QorIQ LS1028A", .revision = "1.0", },
        { /* sentinel */ }
};

static struct soc_device_attribute soc_unreliable_pulse_detection[] = {
        { .family = "QorIQ LX2160A", .revision = "1.0", },
        { .family = "QorIQ LX2160A", .revision = "2.0", },
        { .family = "QorIQ LS1028A", .revision = "1.0", },
        { /* sentinel */ }
};

static void esdhc_init(struct platform_device *pdev, struct sdhci_host *host)
{
        const struct of_device_id *match;
        struct sdhci_pltfm_host *pltfm_host;
        struct sdhci_esdhc *esdhc;
        struct device_node *np;
        struct clk *clk;
        u32 val;
        u16 host_ver;

        pltfm_host = sdhci_priv(host);
        esdhc = sdhci_pltfm_priv(pltfm_host);

        host_ver = sdhci_readw(host, SDHCI_HOST_VERSION);
        esdhc->vendor_ver = (host_ver & SDHCI_VENDOR_VER_MASK) >>
                             SDHCI_VENDOR_VER_SHIFT;
        esdhc->spec_ver = host_ver & SDHCI_SPEC_VER_MASK;
        if (soc_device_match(soc_incorrect_hostver))
                esdhc->quirk_incorrect_hostver = true;
        else
                esdhc->quirk_incorrect_hostver = false;

        if (soc_device_match(soc_fixup_sdhc_clkdivs))
                esdhc->quirk_limited_clk_division = true;
        else
                esdhc->quirk_limited_clk_division = false;

        if (soc_device_match(soc_unreliable_pulse_detection))
                esdhc->quirk_unreliable_pulse_detection = true;
        else
                esdhc->quirk_unreliable_pulse_detection = false;

        match = of_match_node(sdhci_esdhc_of_match, pdev->dev.of_node);
        if (match)
                esdhc->clk_fixup = match->data;
        np = pdev->dev.of_node;

        if (of_device_is_compatible(np, "fsl,p2020-esdhc")) {
                esdhc->quirk_delay_before_data_reset = true;
                esdhc->quirk_trans_complete_erratum = true;
        }

        clk = of_clk_get(np, 0);
        if (!IS_ERR(clk)) {
                /*
                 * esdhc->peripheral_clock would be assigned with a value
                 * which is eSDHC base clock when use periperal clock.
                 * For some platforms, the clock value got by common clk
                 * API is peripheral clock while the eSDHC base clock is
                 * 1/2 peripheral clock.
                 */
                if (of_device_is_compatible(np, "fsl,ls1046a-esdhc") ||
                    of_device_is_compatible(np, "fsl,ls1028a-esdhc") ||
                    of_device_is_compatible(np, "fsl,ls1088a-esdhc"))
                        esdhc->peripheral_clock = clk_get_rate(clk) / 2;
                else
                        esdhc->peripheral_clock = clk_get_rate(clk);

                clk_put(clk);
        }

        esdhc_clock_enable(host, false);
        val = sdhci_readl(host, ESDHC_DMA_SYSCTL);
        /*
         * This bit is not able to be reset by SDHCI_RESET_ALL. Need to
         * initialize it as 1 or 0 once, to override the different value
         * which may be configured in bootloader.
         */
        if (esdhc->peripheral_clock)
                val |= ESDHC_PERIPHERAL_CLK_SEL;
        else
                val &= ~ESDHC_PERIPHERAL_CLK_SEL;
        sdhci_writel(host, val, ESDHC_DMA_SYSCTL);
        esdhc_clock_enable(host, true);
}

static int esdhc_hs400_prepare_ddr(struct mmc_host *mmc)
{
        esdhc_tuning_block_enable(mmc_priv(mmc), false);
        return 0;
}

static int sdhci_esdhc_probe(struct platform_device *pdev)
{
        struct sdhci_host *host;
        struct device_node *np, *tp;
        struct sdhci_pltfm_host *pltfm_host;
        struct sdhci_esdhc *esdhc;
        int ret;

        np = pdev->dev.of_node;

        if (of_property_read_bool(np, "little-endian"))
                host = sdhci_pltfm_init(pdev, &sdhci_esdhc_le_pdata,
                                        sizeof(struct sdhci_esdhc));
        else
                host = sdhci_pltfm_init(pdev, &sdhci_esdhc_be_pdata,
                                        sizeof(struct sdhci_esdhc));

        if (IS_ERR(host))
                return PTR_ERR(host);

        host->mmc_host_ops.start_signal_voltage_switch =
                esdhc_signal_voltage_switch;
        host->mmc_host_ops.execute_tuning = esdhc_execute_tuning;
        host->mmc_host_ops.hs400_prepare_ddr = esdhc_hs400_prepare_ddr;
        host->tuning_delay = 1;

        esdhc_init(pdev, host);

        sdhci_get_of_property(pdev);

        pltfm_host = sdhci_priv(host);
        esdhc = sdhci_pltfm_priv(pltfm_host);
        if (soc_device_match(soc_tuning_erratum_type1))
                esdhc->quirk_tuning_erratum_type1 = true;
        else
                esdhc->quirk_tuning_erratum_type1 = false;

        if (soc_device_match(soc_tuning_erratum_type2))
                esdhc->quirk_tuning_erratum_type2 = true;
        else
                esdhc->quirk_tuning_erratum_type2 = false;

        if (esdhc->vendor_ver == VENDOR_V_22)
                host->quirks2 |= SDHCI_QUIRK2_HOST_NO_CMD23;

        if (esdhc->vendor_ver > VENDOR_V_22)
                host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;

        tp = of_find_compatible_node(NULL, NULL, "fsl,p2020-esdhc");
        if (tp) {
                of_node_put(tp);
                host->quirks |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
                host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
        }

        if (of_device_is_compatible(np, "fsl,p5040-esdhc") ||
            of_device_is_compatible(np, "fsl,p5020-esdhc") ||
            of_device_is_compatible(np, "fsl,p4080-esdhc") ||
            of_device_is_compatible(np, "fsl,p1020-esdhc") ||
            of_device_is_compatible(np, "fsl,t1040-esdhc"))
                host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;

        if (of_device_is_compatible(np, "fsl,ls1021a-esdhc"))
                host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;

        esdhc->quirk_ignore_data_inhibit = false;
        if (of_device_is_compatible(np, "fsl,p2020-esdhc")) {
                /*
                 * Freescale messed up with P2020 as it has a non-standard
                 * host control register
                 */
                host->quirks2 |= SDHCI_QUIRK2_BROKEN_HOST_CONTROL;
                esdhc->quirk_ignore_data_inhibit = true;
        }

        /* call to generic mmc_of_parse to support additional capabilities */
        ret = mmc_of_parse(host->mmc);
        if (ret)
                return ret;

        mmc_of_parse_voltage(host->mmc, &host->ocr_mask);

        return sdhci_add_host(host);
}

static struct platform_driver sdhci_esdhc_driver = {
        .driver = {
                .name = "sdhci-esdhc",
                .probe_type = PROBE_PREFER_ASYNCHRONOUS,
                .of_match_table = sdhci_esdhc_of_match,
                .pm = pm_sleep_ptr(&esdhc_of_dev_pm_ops),
        },
        .probe = sdhci_esdhc_probe,
        .remove = sdhci_pltfm_remove,
};

module_platform_driver(sdhci_esdhc_driver);

MODULE_DESCRIPTION("SDHCI OF driver for Freescale MPC eSDHC");
MODULE_AUTHOR("Xiaobo Xie <X.Xie@freescale.com>, "
              "Anton Vorontsov <avorontsov@ru.mvista.com>");
MODULE_LICENSE("GPL v2");