/* SPDX-License-Identifier: GPL-2.0-only */
/******************************************************************************
 *
 * Copyright(c) 2003 - 2014, 2020, 2023 Intel Corporation. All rights reserved.
 * Copyright (C) 2025 Intel Corporation
 *****************************************************************************/
/*
 * Please use this file (dev.h) for driver implementation definitions.
 * Please use commands.h for uCode API definitions.
 */

#ifndef __iwl_dev_h__
#define __iwl_dev_h__

#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/wait.h>
#include <linux/leds.h>
#include <linux/slab.h>
#include <linux/mutex.h>

#include "fw/img.h"
#include "iwl-nvm-utils.h"
#include "iwl-csr.h"
#include "iwl-debug.h"
#include "iwl-agn-hw.h"
#include "iwl-op-mode.h"
#include "fw/notif-wait.h"
#include "iwl-trans.h"

#include "led.h"
#include "power.h"
#include "rs.h"
#include "tt.h"

/* CT-KILL constants */
#define CT_KILL_THRESHOLD_LEGACY   110 /* in Celsius */
#define CT_KILL_THRESHOLD          114 /* in Celsius */
#define CT_KILL_EXIT_THRESHOLD     95  /* in Celsius */

/* Default noise level to report when noise measurement is not available.
 *   This may be because we're:
 *   1)  Not associated  no beacon statistics being sent to driver)
 *   2)  Scanning (noise measurement does not apply to associated channel)
 * Use default noise value of -127 ... this is below the range of measurable
 *   Rx dBm for all agn devices, so it can indicate "unmeasurable" to user.
 *   Also, -127 works better than 0 when averaging frames with/without
 *   noise info (e.g. averaging might be done in app); measured dBm values are
 *   always negative ... using a negative value as the default keeps all
 *   averages within an s8's (used in some apps) range of negative values. */
#define IWL_NOISE_MEAS_NOT_AVAILABLE (-127)

/*
 * RTS threshold here is total size [2347] minus 4 FCS bytes
 * Per spec:
 *   a value of 0 means RTS on all data/management packets
 *   a value > max MSDU size means no RTS
 * else RTS for data/management frames where MPDU is larger
 *   than RTS value.
 */
#define DEFAULT_RTS_THRESHOLD     2347U
#define MIN_RTS_THRESHOLD         0U
#define MAX_RTS_THRESHOLD         2347U
#define MAX_MSDU_SIZE             2304U
#define MAX_MPDU_SIZE             2346U
#define DEFAULT_BEACON_INTERVAL   200U
#define DEFAULT_SHORT_RETRY_LIMIT 7U
#define DEFAULT_LONG_RETRY_LIMIT  4U

#define IWL_NUM_SCAN_RATES         (2)


#define IEEE80211_DATA_LEN              2304
#define IEEE80211_4ADDR_LEN             30
#define IEEE80211_HLEN                  (IEEE80211_4ADDR_LEN)
#define IEEE80211_FRAME_LEN             (IEEE80211_DATA_LEN + IEEE80211_HLEN)

#define SUP_RATE_11A_MAX_NUM_CHANNELS  8
#define SUP_RATE_11B_MAX_NUM_CHANNELS  4
#define SUP_RATE_11G_MAX_NUM_CHANNELS  12

#define IWL_SUPPORTED_RATES_IE_LEN         8

#define IWL_INVALID_RATE     0xFF
#define IWL_INVALID_VALUE    -1

union iwl_ht_rate_supp {
        u16 rates;
        struct {
                u8 siso_rate;
                u8 mimo_rate;
        };
};

struct iwl_ht_config {
        bool single_chain_sufficient;
        enum ieee80211_smps_mode smps; /* current smps mode */
};

/* QoS structures */
struct iwl_qos_info {
        int qos_active;
        struct iwl_qosparam_cmd def_qos_parm;
};

/**
 * enum iwl_agg_state - aggregation state
 *
 * The state machine of the BA agreement establishment / tear down.
 * These states relate to a specific RA / TID.
 *
 * @IWL_AGG_OFF: aggregation is not used
 * @IWL_AGG_STARTING: aggregation are starting (between start and oper)
 * @IWL_AGG_ON: aggregation session is up
 * @IWL_EMPTYING_HW_QUEUE_ADDBA: establishing a BA session - waiting for the
 *      HW queue to be empty from packets for this RA /TID.
 * @IWL_EMPTYING_HW_QUEUE_DELBA: tearing down a BA session - waiting for the
 *      HW queue to be empty from packets for this RA /TID.
 */
enum iwl_agg_state {
        IWL_AGG_OFF = 0,
        IWL_AGG_STARTING,
        IWL_AGG_ON,
        IWL_EMPTYING_HW_QUEUE_ADDBA,
        IWL_EMPTYING_HW_QUEUE_DELBA,
};

/**
 * struct iwl_ht_agg - aggregation state machine
 *
 * This structs holds the states for the BA agreement establishment and tear
 * down. It also holds the state during the BA session itself. This struct is
 * duplicated for each RA / TID.
 *
 * @rate_n_flags: Rate at which Tx was attempted. Holds the data between the
 *      Tx response (REPLY_TX), and the block ack notification
 *      (REPLY_COMPRESSED_BA).
 * @state: state of the BA agreement establishment / tear down.
 * @txq_id: Tx queue used by the BA session
 * @ssn: the first packet to be sent in AGG HW queue in Tx AGG start flow, or
 *      the first packet to be sent in legacy HW queue in Tx AGG stop flow.
 *      Basically when next_reclaimed reaches ssn, we can tell mac80211 that
 *      we are ready to finish the Tx AGG stop / start flow.
 * @wait_for_ba: Expect block-ack before next Tx reply
 */
struct iwl_ht_agg {
        u32 rate_n_flags;
        enum iwl_agg_state state;
        u16 txq_id;
        u16 ssn;
        bool wait_for_ba;
};

/**
 * struct iwl_tid_data - one for each RA / TID
 *
 * This structs holds the states for each RA / TID.
 *
 * @seq_number: the next WiFi sequence number to use
 * @next_reclaimed: the WiFi sequence number of the next packet to be acked.
 *      This is basically (last acked packet++).
 * @agg: aggregation state machine
 */
struct iwl_tid_data {
        u16 seq_number;
        u16 next_reclaimed;
        struct iwl_ht_agg agg;
};

/*
 * Structure should be accessed with sta_lock held. When station addition
 * is in progress (IWL_STA_UCODE_INPROGRESS) it is possible to access only
 * the commands (iwl_addsta_cmd and iwl_link_quality_cmd) without sta_lock
 * held.
 */
struct iwl_station_entry {
        struct iwl_addsta_cmd sta;
        u8 used, ctxid;
        struct iwl_link_quality_cmd *lq;
};

/*
 * iwl_station_priv: Driver's private station information
 *
 * When mac80211 creates a station it reserves some space (hw->sta_data_size)
 * in the structure for use by driver. This structure is places in that
 * space.
 */
struct iwl_station_priv {
        struct iwl_rxon_context *ctx;
        struct iwl_lq_sta lq_sta;
        atomic_t pending_frames;
        bool client;
        bool asleep;
        u8 max_agg_bufsize;
        u8 sta_id;
};

/*
 * struct iwl_vif_priv - driver's private per-interface information
 *
 * When mac80211 allocates a virtual interface, it can allocate
 * space for us to put data into.
 */
struct iwl_vif_priv {
        struct iwl_rxon_context *ctx;
        u8 ibss_bssid_sta_id;
};

struct iwl_sensitivity_ranges {
        u16 min_nrg_cck;

        u16 nrg_th_cck;
        u16 nrg_th_ofdm;

        u16 auto_corr_min_ofdm;
        u16 auto_corr_min_ofdm_mrc;
        u16 auto_corr_min_ofdm_x1;
        u16 auto_corr_min_ofdm_mrc_x1;

        u16 auto_corr_max_ofdm;
        u16 auto_corr_max_ofdm_mrc;
        u16 auto_corr_max_ofdm_x1;
        u16 auto_corr_max_ofdm_mrc_x1;

        u16 auto_corr_max_cck;
        u16 auto_corr_max_cck_mrc;
        u16 auto_corr_min_cck;
        u16 auto_corr_min_cck_mrc;

        u16 barker_corr_th_min;
        u16 barker_corr_th_min_mrc;
        u16 nrg_th_cca;
};

/******************************************************************************
 *
 * Functions implemented in core module which are forward declared here
 * for use by iwl-[4-5].c
 *
 * NOTE:  The implementation of these functions are not hardware specific
 * which is why they are in the core module files.
 *
 * Naming convention --
 * iwl_         <-- Is part of iwlwifi
 * iwlXXXX_     <-- Hardware specific (implemented in iwl-XXXX.c for XXXX)
 *
 ****************************************************************************/
void iwl_update_chain_flags(struct iwl_priv *priv);
extern const u8 iwl_bcast_addr[ETH_ALEN];

#define IWL_OPERATION_MODE_AUTO     0
#define IWL_OPERATION_MODE_HT_ONLY  1
#define IWL_OPERATION_MODE_MIXED    2
#define IWL_OPERATION_MODE_20MHZ    3

#define TX_POWER_IWL_ILLEGAL_VOLTAGE -10000

/* Sensitivity and chain noise calibration */
#define INITIALIZATION_VALUE            0xFFFF
#define IWL_CAL_NUM_BEACONS             16
#define MAXIMUM_ALLOWED_PATHLOSS        15

#define CHAIN_NOISE_MAX_DELTA_GAIN_CODE 3

#define MAX_FA_OFDM  50
#define MIN_FA_OFDM  5
#define MAX_FA_CCK   50
#define MIN_FA_CCK   5

#define AUTO_CORR_STEP_OFDM       1

#define AUTO_CORR_STEP_CCK     3
#define AUTO_CORR_MAX_TH_CCK   160

#define NRG_DIFF               2
#define NRG_STEP_CCK           2
#define NRG_MARGIN             8
#define MAX_NUMBER_CCK_NO_FA 100

#define AUTO_CORR_CCK_MIN_VAL_DEF    (125)

#define CHAIN_A             0
#define CHAIN_B             1
#define CHAIN_C             2
#define CHAIN_NOISE_DELTA_GAIN_INIT_VAL 4
#define ALL_BAND_FILTER                 0xFF00
#define IN_BAND_FILTER                  0xFF
#define MIN_AVERAGE_NOISE_MAX_VALUE     0xFFFFFFFF

#define NRG_NUM_PREV_STAT_L     20
#define NUM_RX_CHAINS           3

enum iwlagn_false_alarm_state {
        IWL_FA_TOO_MANY = 0,
        IWL_FA_TOO_FEW = 1,
        IWL_FA_GOOD_RANGE = 2,
};

enum iwlagn_chain_noise_state {
        IWL_CHAIN_NOISE_ALIVE = 0,  /* must be 0 */
        IWL_CHAIN_NOISE_ACCUMULATE,
        IWL_CHAIN_NOISE_CALIBRATED,
        IWL_CHAIN_NOISE_DONE,
};

/* Sensitivity calib data */
struct iwl_sensitivity_data {
        u32 auto_corr_ofdm;
        u32 auto_corr_ofdm_mrc;
        u32 auto_corr_ofdm_x1;
        u32 auto_corr_ofdm_mrc_x1;
        u32 auto_corr_cck;
        u32 auto_corr_cck_mrc;

        u32 last_bad_plcp_cnt_ofdm;
        u32 last_fa_cnt_ofdm;
        u32 last_bad_plcp_cnt_cck;
        u32 last_fa_cnt_cck;

        u32 nrg_curr_state;
        u32 nrg_prev_state;
        u32 nrg_value[10];
        u8  nrg_silence_rssi[NRG_NUM_PREV_STAT_L];
        u32 nrg_silence_ref;
        u32 nrg_energy_idx;
        u32 nrg_silence_idx;
        u32 nrg_th_cck;
        s32 nrg_auto_corr_silence_diff;
        u32 num_in_cck_no_fa;
        u32 nrg_th_ofdm;

        u16 barker_corr_th_min;
        u16 barker_corr_th_min_mrc;
        u16 nrg_th_cca;
};

/* Chain noise (differential Rx gain) calib data */
struct iwl_chain_noise_data {
        u32 active_chains;
        u32 chain_noise_a;
        u32 chain_noise_b;
        u32 chain_noise_c;
        u32 chain_signal_a;
        u32 chain_signal_b;
        u32 chain_signal_c;
        u16 beacon_count;
        u8 disconn_array[NUM_RX_CHAINS];
        u8 delta_gain_code[NUM_RX_CHAINS];
        u8 radio_write;
        u8 state;
};

enum {
        MEASUREMENT_READY = (1 << 0),
        MEASUREMENT_ACTIVE = (1 << 1),
};

/* reply_tx_statistics (for _agn devices) */
struct reply_tx_error_statistics {
        u32 pp_delay;
        u32 pp_few_bytes;
        u32 pp_bt_prio;
        u32 pp_quiet_period;
        u32 pp_calc_ttak;
        u32 int_crossed_retry;
        u32 short_limit;
        u32 long_limit;
        u32 fifo_underrun;
        u32 drain_flow;
        u32 rfkill_flush;
        u32 life_expire;
        u32 dest_ps;
        u32 host_abort;
        u32 bt_retry;
        u32 sta_invalid;
        u32 frag_drop;
        u32 tid_disable;
        u32 fifo_flush;
        u32 insuff_cf_poll;
        u32 fail_hw_drop;
        u32 sta_color_mismatch;
        u32 unknown;
};

/* reply_agg_tx_statistics (for _agn devices) */
struct reply_agg_tx_error_statistics {
        u32 underrun;
        u32 bt_prio;
        u32 few_bytes;
        u32 abort;
        u32 last_sent_ttl;
        u32 last_sent_try;
        u32 last_sent_bt_kill;
        u32 scd_query;
        u32 bad_crc32;
        u32 response;
        u32 dump_tx;
        u32 delay_tx;
        u32 unknown;
};

/*
 * schedule the timer to wake up every UCODE_TRACE_PERIOD milliseconds
 * to perform continuous uCode event logging operation if enabled
 */
#define UCODE_TRACE_PERIOD (10)

/*
 * iwl_event_log: current uCode event log position
 *
 * @ucode_trace: enable/disable ucode continuous trace timer
 * @num_wraps: how many times the event buffer wraps
 * @next_entry:  the entry just before the next one that uCode would fill
 * @non_wraps_count: counter for no wrap detected when dump ucode events
 * @wraps_once_count: counter for wrap once detected when dump ucode events
 * @wraps_more_count: counter for wrap more than once detected
 *                    when dump ucode events
 */
struct iwl_event_log {
        bool ucode_trace;
        u32 num_wraps;
        u32 next_entry;
        int non_wraps_count;
        int wraps_once_count;
        int wraps_more_count;
};

#define IWL_DELAY_NEXT_FORCE_RF_RESET  (HZ*3)

/* BT Antenna Coupling Threshold (dB) */
#define IWL_BT_ANTENNA_COUPLING_THRESHOLD       (35)

/* Firmware reload counter and Timestamp */
#define IWL_MIN_RELOAD_DURATION         1000 /* 1000 ms */
#define IWL_MAX_CONTINUE_RELOAD_CNT     4


struct iwl_rf_reset {
        int reset_request_count;
        int reset_success_count;
        int reset_reject_count;
        unsigned long last_reset_jiffies;
};

enum iwl_rxon_context_id {
        IWL_RXON_CTX_BSS,
        IWL_RXON_CTX_PAN,

        NUM_IWL_RXON_CTX
};

/* extend beacon time format bit shifting  */
/*
 * for _agn devices
 * bits 31:22 - extended
 * bits 21:0  - interval
 */
#define IWLAGN_EXT_BEACON_TIME_POS      22

struct iwl_rxon_context {
        struct ieee80211_vif *vif;

        u8 mcast_queue;
        u8 ac_to_queue[IEEE80211_NUM_ACS];
        u8 ac_to_fifo[IEEE80211_NUM_ACS];

        /*
         * We could use the vif to indicate active, but we
         * also need it to be active during disabling when
         * we already removed the vif for type setting.
         */
        bool always_active, is_active;

        bool ht_need_multiple_chains;

        enum iwl_rxon_context_id ctxid;

        u32 interface_modes, exclusive_interface_modes;
        u8 unused_devtype, ap_devtype, ibss_devtype, station_devtype;

        /*
         * We declare this const so it can only be
         * changed via explicit cast within the
         * routines that actually update the physical
         * hardware.
         */
        const struct iwl_rxon_cmd active;
        struct iwl_rxon_cmd staging;

        struct iwl_rxon_time_cmd timing;

        struct iwl_qos_info qos_data;

        u8 bcast_sta_id, ap_sta_id;

        u8 rxon_cmd, rxon_assoc_cmd, rxon_timing_cmd;
        u8 qos_cmd;
        u8 wep_key_cmd;

        struct iwl_wep_key wep_keys[WEP_KEYS_MAX];
        u8 key_mapping_keys;

        __le32 station_flags;

        int beacon_int;

        struct {
                bool non_gf_sta_present;
                u8 protection;
                bool enabled, is_40mhz;
                u8 extension_chan_offset;
        } ht;
};

enum iwl_scan_type {
        IWL_SCAN_NORMAL,
        IWL_SCAN_RADIO_RESET,
};

/**
 * struct iwl_hw_params - HW parameters
 *
 * Holds the module parameters
 *
 * @tx_chains_num: Number of TX chains
 * @rx_chains_num: Number of RX chains
 * @ct_kill_threshold: temperature threshold - in hw dependent unit
 * @ct_kill_exit_threshold: when to reeable the device - in hw dependent unit
 *      relevant for 1000, 6000 and up
 * @struct iwl_sensitivity_ranges: range of sensitivity values
 * @use_rts_for_aggregation: use rts/cts protection for HT traffic
 * @sens: sensitivity ranges pointer
 */
struct iwl_hw_params {
        u8  tx_chains_num;
        u8  rx_chains_num;
        bool use_rts_for_aggregation;
        u32 ct_kill_threshold;
        u32 ct_kill_exit_threshold;

        const struct iwl_sensitivity_ranges *sens;
};

/**
 * struct iwl_dvm_bt_params - DVM specific BT (coex) parameters
 * @advanced_bt_coexist: support advanced bt coexist
 * @bt_init_traffic_load: specify initial bt traffic load
 * @bt_prio_boost: default bt priority boost value
 * @agg_time_limit: maximum number of uSec in aggregation
 * @bt_sco_disable: uCode should not response to BT in SCO/ESCO mode
 * @bt_session_2: indicates version 2 of the BT command is used
 */
struct iwl_dvm_bt_params {
        bool advanced_bt_coexist;
        u8 bt_init_traffic_load;
        u32 bt_prio_boost;
        u16 agg_time_limit;
        bool bt_sco_disable;
        bool bt_session_2;
};

/**
 * struct iwl_dvm_cfg - DVM firmware specific device configuration
 * @set_hw_params: set hardware parameters
 * @set_channel_switch: send channel switch command
 * @nic_config: apply device specific configuration
 * @temperature: read temperature
 * @adv_thermal_throttle: support advance thermal throttle
 * @support_ct_kill_exit: support ct kill exit condition
 * @plcp_delta_threshold: plcp error rate threshold used to trigger
 *      radio tuning when there is a high receiving plcp error rate
 * @chain_noise_scale: default chain noise scale used for gain computation
 * @hd_v2: v2 of enhanced sensitivity value, used for 2000 series and up
 * @no_idle_support: do not support idle mode
 * @bt_params: pointer to BT parameters
 * @need_temp_offset_calib: need to perform temperature offset calibration
 * @no_xtal_calib: some devices do not need crystal calibration data,
 *      don't send it to those
 * @temp_offset_v2: support v2 of temperature offset calibration
 * @adv_pm: advanced power management
 */
struct iwl_dvm_cfg {
        void (*set_hw_params)(struct iwl_priv *priv);
        int (*set_channel_switch)(struct iwl_priv *priv,
                                  struct ieee80211_channel_switch *ch_switch);
        void (*nic_config)(struct iwl_priv *priv);
        void (*temperature)(struct iwl_priv *priv);

        const struct iwl_dvm_bt_params *bt_params;
        s32 chain_noise_scale;
        u8 plcp_delta_threshold;
        bool adv_thermal_throttle;
        bool support_ct_kill_exit;
        bool hd_v2;
        bool no_idle_support;
        bool need_temp_offset_calib;
        bool no_xtal_calib;
        bool temp_offset_v2;
        bool adv_pm;
};

struct iwl_wipan_noa_data {
        struct rcu_head rcu_head;
        u32 length;
        u8 data[];
};

/* Calibration disabling bit mask */
enum {
        IWL_CALIB_ENABLE_ALL                    = 0,

        IWL_SENSITIVITY_CALIB_DISABLED          = BIT(0),
        IWL_CHAIN_NOISE_CALIB_DISABLED          = BIT(1),
        IWL_TX_POWER_CALIB_DISABLED             = BIT(2),

        IWL_CALIB_DISABLE_ALL                   = 0xFFFFFFFF,
};

#define IWL_OP_MODE_GET_DVM(_iwl_op_mode) \
        ((struct iwl_priv *) ((_iwl_op_mode)->op_mode_specific))

#define IWL_MAC80211_GET_DVM(_hw) \
        ((struct iwl_priv *) ((struct iwl_op_mode *) \
        (_hw)->priv)->op_mode_specific)

struct iwl_priv {

        struct iwl_trans *trans;
        struct device *dev;             /* for debug prints only */
        const struct iwl_rf_cfg *cfg;
        const struct iwl_fw *fw;
        const struct iwl_dvm_cfg *lib;
        unsigned long status;

        spinlock_t sta_lock;
        struct mutex mutex;

        unsigned long transport_queue_stop;
        bool passive_no_rx;
#define IWL_INVALID_MAC80211_QUEUE      0xff
        u8 queue_to_mac80211[IWL_MAX_HW_QUEUES];
        atomic_t queue_stop_count[IWL_MAX_HW_QUEUES];

        unsigned long agg_q_alloc[BITS_TO_LONGS(IWL_MAX_HW_QUEUES)];

        /* ieee device used by generic ieee processing code */
        struct ieee80211_hw *hw;

        struct napi_struct *napi;

        struct list_head calib_results;

        struct workqueue_struct *workqueue;

        struct iwl_hw_params hw_params;

        enum nl80211_band band;
        u8 valid_contexts;

        void (*rx_handlers[REPLY_MAX])(struct iwl_priv *priv,
                                       struct iwl_rx_cmd_buffer *rxb);

        struct iwl_notif_wait_data notif_wait;

        /* spectrum measurement report caching */
        struct iwl_spectrum_notification measure_report;
        u8 measurement_status;

        /* ucode beacon time */
        u32 ucode_beacon_time;
        int missed_beacon_threshold;

        /* track IBSS manager (last beacon) status */
        u32 ibss_manager;

        /* jiffies when last recovery from statistics was performed */
        unsigned long rx_statistics_jiffies;

        /*counters */
        u32 rx_handlers_stats[REPLY_MAX];

        /* rf reset */
        struct iwl_rf_reset rf_reset;

        /* firmware reload counter and timestamp */
        unsigned long reload_jiffies;
        int reload_count;
        bool ucode_loaded;

        u8 plcp_delta_threshold;

        /* thermal calibration */
        s32 temperature;        /* Celsius */
        s32 last_temperature;

        struct iwl_wipan_noa_data __rcu *noa_data;

        /* Scan related variables */
        unsigned long scan_start;
        unsigned long scan_start_tsf;
        size_t scan_cmd_size;
        void *scan_cmd;
        enum nl80211_band scan_band;
        struct cfg80211_scan_request *scan_request;
        struct ieee80211_vif *scan_vif;
        enum iwl_scan_type scan_type;
        u8 scan_tx_ant[NUM_NL80211_BANDS];
        u8 mgmt_tx_ant;

        /* max number of station keys */
        u8 sta_key_max_num;

        bool new_scan_threshold_behaviour;

        bool wowlan;

        /* EEPROM MAC addresses */
        struct mac_address addresses[2];

        struct iwl_rxon_context contexts[NUM_IWL_RXON_CTX];

        __le16 switch_channel;

        u8 start_calib;
        struct iwl_sensitivity_data sensitivity_data;
        struct iwl_chain_noise_data chain_noise_data;
        __le16 sensitivity_tbl[HD_TABLE_SIZE];
        __le16 enhance_sensitivity_tbl[ENHANCE_HD_TABLE_ENTRIES];

        struct iwl_ht_config current_ht_config;

        /* Rate scaling data */
        u8 retry_rate;

        int activity_timer_active;

        struct iwl_power_mgr power_data;
        struct iwl_tt_mgmt thermal_throttle;

        /* station table variables */
        int num_stations;
        struct iwl_station_entry stations[IWLAGN_STATION_COUNT];
        unsigned long ucode_key_table;
        struct iwl_tid_data tid_data[IWLAGN_STATION_COUNT][IWL_MAX_TID_COUNT];
        atomic_t num_aux_in_flight;

        u8 mac80211_registered;

        /* Indication if ieee80211_ops->open has been called */
        u8 is_open;

        enum nl80211_iftype iw_mode;

        /* Last Rx'd beacon timestamp */
        u64 timestamp;

        struct {
                __le32 flag;
                struct statistics_general_common common;
                struct statistics_rx_non_phy rx_non_phy;
                struct statistics_rx_phy rx_ofdm;
                struct statistics_rx_ht_phy rx_ofdm_ht;
                struct statistics_rx_phy rx_cck;
                struct statistics_tx tx;
#ifdef CONFIG_IWLWIFI_DEBUGFS
                struct statistics_bt_activity bt_activity;
                __le32 num_bt_kills, accum_num_bt_kills;
#endif
                spinlock_t lock;
        } statistics;
#ifdef CONFIG_IWLWIFI_DEBUGFS
        struct {
                struct statistics_general_common common;
                struct statistics_rx_non_phy rx_non_phy;
                struct statistics_rx_phy rx_ofdm;
                struct statistics_rx_ht_phy rx_ofdm_ht;
                struct statistics_rx_phy rx_cck;
                struct statistics_tx tx;
                struct statistics_bt_activity bt_activity;
        } accum_stats, delta_stats, max_delta_stats;
#endif

        /*
         * reporting the number of tids has AGG on. 0 means
         * no AGGREGATION
         */
        u8 agg_tids_count;

        struct iwl_rx_phy_res last_phy_res;
        u32 ampdu_ref;
        bool last_phy_res_valid;

        /*
         * chain noise reset and gain commands are the
         * two extra calibration commands follows the standard
         * phy calibration commands
         */
        u8 phy_calib_chain_noise_reset_cmd;
        u8 phy_calib_chain_noise_gain_cmd;

        /* counts reply_tx error */
        struct reply_tx_error_statistics reply_tx_stats;
        struct reply_agg_tx_error_statistics reply_agg_tx_stats;

        /* bt coex */
        u8 bt_enable_flag;
        u8 bt_status;
        u8 bt_traffic_load, last_bt_traffic_load;
        bool bt_ch_announce;
        bool bt_full_concurrent;
        __le32 kill_ack_mask;
        __le32 kill_cts_mask;
        __le16 bt_valid;
        bool reduced_txpower;
        u16 bt_on_thresh;
        u16 bt_duration;
        u16 dynamic_frag_thresh;
        u8 bt_ci_compliance;
        struct work_struct bt_traffic_change_work;
        bool bt_enable_pspoll;
        struct iwl_rxon_context *cur_rssi_ctx;
        bool bt_is_sco;

        struct work_struct restart;
        struct work_struct scan_completed;
        struct work_struct abort_scan;

        struct work_struct beacon_update;
        struct iwl_rxon_context *beacon_ctx;
        struct sk_buff *beacon_skb;
        void *beacon_cmd;

        struct work_struct tt_work;
        struct work_struct ct_enter;
        struct work_struct ct_exit;
        struct work_struct start_internal_scan;
        struct work_struct tx_flush;
        struct work_struct bt_full_concurrency;
        struct work_struct bt_runtime_config;

        struct delayed_work scan_check;

        /* TX Power settings */
        s8 tx_power_user_lmt;
        s8 tx_power_next;

#ifdef CONFIG_IWLWIFI_DEBUGFS
        /* debugfs */
        struct dentry *debugfs_dir;
        u32 dbgfs_sram_offset, dbgfs_sram_len;
        bool disable_ht40;
        void *wowlan_sram;
#endif /* CONFIG_IWLWIFI_DEBUGFS */

        struct iwl_nvm_data *nvm_data;
        /* eeprom blob for debugfs */
        u8 *eeprom_blob;
        size_t eeprom_blob_size;

        struct work_struct txpower_work;
        u32 calib_disabled;
        struct work_struct run_time_calib_work;
        struct timer_list statistics_periodic;
        struct timer_list ucode_trace;

        struct iwl_event_log event_log;

#ifdef CONFIG_IWLWIFI_LEDS
        struct led_classdev led;
        unsigned long blink_on, blink_off;
        bool led_registered;
#endif

        /* WoWLAN GTK rekey data */
        u8 kck[NL80211_KCK_LEN], kek[NL80211_KEK_LEN];
        __le64 replay_ctr;
        __le16 last_seq_ctl;
        bool have_rekey_data;
#ifdef CONFIG_PM_SLEEP
        struct wiphy_wowlan_support wowlan_support;
#endif

        /* device_pointers: pointers to ucode event tables */
        struct {
                u32 error_event_table;
                u32 log_event_table;
        } device_pointers;

        /* indicator of loaded ucode image */
        enum iwl_ucode_type cur_ucode;
}; /*iwl_priv */

static inline struct iwl_rxon_context *
iwl_rxon_ctx_from_vif(struct ieee80211_vif *vif)
{
        struct iwl_vif_priv *vif_priv = (void *)vif->drv_priv;

        return vif_priv->ctx;
}

#define for_each_context(priv, ctx)                             \
        for (ctx = &priv->contexts[IWL_RXON_CTX_BSS];           \
             ctx < &priv->contexts[NUM_IWL_RXON_CTX]; ctx++)    \
                if (priv->valid_contexts & BIT(ctx->ctxid))

static inline int iwl_is_associated_ctx(struct iwl_rxon_context *ctx)
{
        return (ctx->active.filter_flags & RXON_FILTER_ASSOC_MSK) ? 1 : 0;
}

static inline int iwl_is_associated(struct iwl_priv *priv,
                                    enum iwl_rxon_context_id ctxid)
{
        return iwl_is_associated_ctx(&priv->contexts[ctxid]);
}

static inline int iwl_is_any_associated(struct iwl_priv *priv)
{
        struct iwl_rxon_context *ctx;
        for_each_context(priv, ctx)
                if (iwl_is_associated_ctx(ctx))
                        return true;
        return false;
}

#endif                          /* __iwl_dev_h__ */