// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * vt1211.c - driver for the VIA VT1211 Super-I/O chip integrated hardware
 *            monitoring features
 * Copyright (C) 2006 Juerg Haefliger <juergh@gmail.com>
 *
 * This driver is based on the driver for kernel 2.4 by Mark D. Studebaker
 * and its port to kernel 2.6 by Lars Ekman.
 */

#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/platform_device.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/hwmon-vid.h>
#include <linux/err.h>
#include <linux/mutex.h>
#include <linux/ioport.h>
#include <linux/acpi.h>
#include <linux/io.h>

static int uch_config = -1;
module_param(uch_config, int, 0);
MODULE_PARM_DESC(uch_config, "Initialize the universal channel configuration");

static int int_mode = -1;
module_param(int_mode, int, 0);
MODULE_PARM_DESC(int_mode, "Force the temperature interrupt mode");

static unsigned short force_id;
module_param(force_id, ushort, 0);
MODULE_PARM_DESC(force_id, "Override the detected device ID");

static struct platform_device *pdev;

#define DRVNAME "vt1211"

/* ---------------------------------------------------------------------
 * Registers
 *
 * The sensors are defined as follows.
 *
 * Sensor          Voltage Mode   Temp Mode   Notes (from the datasheet)
 * --------        ------------   ---------   --------------------------
 * Reading 1                      temp1       Intel thermal diode
 * Reading 3                      temp2       Internal thermal diode
 * UCH1/Reading2   in0            temp3       NTC type thermistor
 * UCH2            in1            temp4       +2.5V
 * UCH3            in2            temp5       VccP
 * UCH4            in3            temp6       +5V
 * UCH5            in4            temp7       +12V
 * 3.3V            in5                        Internal VDD (+3.3V)
 *
 * --------------------------------------------------------------------- */

/* Voltages (in) numbered 0-5 (ix) */
#define VT1211_REG_IN(ix)               (0x21 + (ix))
#define VT1211_REG_IN_MIN(ix)           ((ix) == 0 ? 0x3e : 0x2a + 2 * (ix))
#define VT1211_REG_IN_MAX(ix)           ((ix) == 0 ? 0x3d : 0x29 + 2 * (ix))

/* Temperatures (temp) numbered 0-6 (ix) */
static u8 regtemp[]     = {0x1f, 0x20, 0x21, 0x22, 0x23, 0x24, 0x25};
static u8 regtempmax[]  = {0x39, 0x1d, 0x3d, 0x2b, 0x2d, 0x2f, 0x31};
static u8 regtemphyst[] = {0x3a, 0x1e, 0x3e, 0x2c, 0x2e, 0x30, 0x32};

/* Fans numbered 0-1 (ix) */
#define VT1211_REG_FAN(ix)              (0x29 + (ix))
#define VT1211_REG_FAN_MIN(ix)          (0x3b + (ix))
#define VT1211_REG_FAN_DIV               0x47

/* PWMs numbered 0-1 (ix) */
/* Auto points numbered 0-3 (ap) */
#define VT1211_REG_PWM(ix)              (0x60 + (ix))
#define VT1211_REG_PWM_CLK               0x50
#define VT1211_REG_PWM_CTL               0x51
#define VT1211_REG_PWM_AUTO_TEMP(ap)    (0x55 - (ap))
#define VT1211_REG_PWM_AUTO_PWM(ix, ap) (0x58 + 2 * (ix) - (ap))

/* Miscellaneous registers */
#define VT1211_REG_CONFIG               0x40
#define VT1211_REG_ALARM1               0x41
#define VT1211_REG_ALARM2               0x42
#define VT1211_REG_VID                  0x45
#define VT1211_REG_UCH_CONFIG           0x4a
#define VT1211_REG_TEMP1_CONFIG         0x4b
#define VT1211_REG_TEMP2_CONFIG         0x4c

/* In, temp & fan alarm bits */
static const u8 bitalarmin[]    = {11, 0, 1, 3, 8, 2, 9};
static const u8 bitalarmtemp[]  = {4, 15, 11, 0, 1, 3, 8};
static const u8 bitalarmfan[]   = {6, 7};

/* ---------------------------------------------------------------------
 * Data structures and manipulation thereof
 * --------------------------------------------------------------------- */

struct vt1211_data {
        unsigned short addr;
        const char *name;
        struct device *hwmon_dev;

        struct mutex update_lock;
        bool valid;                     /* true if following fields are valid */
        unsigned long last_updated;     /* In jiffies */

        /* Register values */
        u8  in[6];
        u8  in_max[6];
        u8  in_min[6];
        u8  temp[7];
        u8  temp_max[7];
        u8  temp_hyst[7];
        u8  fan[2];
        u8  fan_min[2];
        u8  fan_div[2];
        u8  fan_ctl;
        u8  pwm[2];
        u8  pwm_ctl[2];
        u8  pwm_clk;
        u8  pwm_auto_temp[4];
        u8  pwm_auto_pwm[2][4];
        u8  vid;                /* Read once at init time */
        u8  vrm;
        u8  uch_config;         /* Read once at init time */
        u16 alarms;
};

/* ix = [0-5] */
#define ISVOLT(ix, uch_config)  ((ix) > 4 ? 1 : \
                                 !(((uch_config) >> ((ix) + 2)) & 1))

/* ix = [0-6] */
#define ISTEMP(ix, uch_config)  ((ix) < 2 ? 1 : \
                                 ((uch_config) >> (ix)) & 1)

/*
 * in5 (ix = 5) is special. It's the internal 3.3V so it's scaled in the
 * driver according to the VT1211 BIOS porting guide
 */
static int in_from_reg(int ix, int reg)
{
        if (reg < 3)
                return 0;
        if (ix == 5)
                return ((reg - 3) * 15882 + 479) / 958;
        return ((reg - 3) * 10000 + 479) / 958;
}

#define IN_TO_REG(ix, val)      (clamp_val((ix) == 5 ? \
                                 ((val) * 958 + 7941) / 15882 + 3 : \
                                 ((val) * 958 + 5000) / 10000 + 3, 0, 255))

/*
 * temp1 (ix = 0) is an intel thermal diode which is scaled in user space.
 * temp2 (ix = 1) is the internal temp diode so it's scaled in the driver
 * according to some measurements that I took on an EPIA M10000.
 * temp3-7 are thermistor based so the driver returns the voltage measured at
 * the pin (range 0V - 2.2V).
 */
static int temp_from_reg(int ix, int reg)
{
        if (ix == 0)
                return reg * 1000;
        if (ix == 1)
                return reg < 51 ? 0 : (reg - 51) * 1000;
        return ((253 - reg) * 2200 + 105) / 210;
}

#define TEMP_TO_REG(ix, val)    clamp_val( \
                                 ((ix) == 0 ? ((val) + 500) / 1000 : \
                                  (ix) == 1 ? ((val) + 500) / 1000 + 51 : \
                                  253 - ((val) * 210 + 1100) / 2200), 0, 255)

#define DIV_FROM_REG(reg)       (1 << (reg))

static int rpm_from_reg(int reg, int div)
{
        if (reg == 0 || reg == 255)
                return 0;

        return 1310720 / reg / DIV_FROM_REG(div);
}

#define RPM_TO_REG(val, div)    ((val) == 0 ? 255 : \
                                 clamp_val((1310720 / (val) / \
                                 DIV_FROM_REG(div)), 1, 254))

/* ---------------------------------------------------------------------
 * Super-I/O constants and functions
 * --------------------------------------------------------------------- */

/*
 * Configuration index port registers
 * The vt1211 can live at 2 different addresses so we need to probe both
 */
#define SIO_REG_CIP1            0x2e
#define SIO_REG_CIP2            0x4e

/* Configuration registers */
#define SIO_VT1211_LDN          0x07    /* logical device number */
#define SIO_VT1211_DEVID        0x20    /* device ID */
#define SIO_VT1211_DEVREV       0x21    /* device revision */
#define SIO_VT1211_ACTIVE       0x30    /* HW monitor active */
#define SIO_VT1211_BADDR        0x60    /* base I/O address */
#define SIO_VT1211_ID           0x3c    /* VT1211 device ID */

/* VT1211 logical device numbers */
#define SIO_VT1211_LDN_HWMON    0x0b    /* HW monitor */

static inline int superio_inb(int sio_cip, int reg)
{
        outb(reg, sio_cip);
        return inb(sio_cip + 1);
}

static inline void superio_select(int sio_cip, int ldn)
{
        outb(SIO_VT1211_LDN, sio_cip);
        outb(ldn, sio_cip + 1);
}

static inline int superio_enter(int sio_cip)
{
        if (!request_muxed_region(sio_cip, 2, DRVNAME))
                return -EBUSY;

        outb(0x87, sio_cip);
        outb(0x87, sio_cip);

        return 0;
}

static inline void superio_exit(int sio_cip)
{
        outb(0xaa, sio_cip);
        release_region(sio_cip, 2);
}

/* ---------------------------------------------------------------------
 * Device I/O access
 * --------------------------------------------------------------------- */

static inline u8 vt1211_read8(struct vt1211_data *data, u8 reg)
{
        return inb(data->addr + reg);
}

static inline void vt1211_write8(struct vt1211_data *data, u8 reg, u8 val)
{
        outb(val, data->addr + reg);
}

static struct vt1211_data *vt1211_update_device(struct device *dev)
{
        struct vt1211_data *data = dev_get_drvdata(dev);
        int ix, val;

        mutex_lock(&data->update_lock);

        /* registers cache is refreshed after 1 second */
        if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
                /* read VID */
                data->vid = vt1211_read8(data, VT1211_REG_VID) & 0x1f;

                /* voltage (in) registers */
                for (ix = 0; ix < ARRAY_SIZE(data->in); ix++) {
                        if (ISVOLT(ix, data->uch_config)) {
                                data->in[ix] = vt1211_read8(data,
                                                VT1211_REG_IN(ix));
                                data->in_min[ix] = vt1211_read8(data,
                                                VT1211_REG_IN_MIN(ix));
                                data->in_max[ix] = vt1211_read8(data,
                                                VT1211_REG_IN_MAX(ix));
                        }
                }

                /* temp registers */
                for (ix = 0; ix < ARRAY_SIZE(data->temp); ix++) {
                        if (ISTEMP(ix, data->uch_config)) {
                                data->temp[ix] = vt1211_read8(data,
                                                regtemp[ix]);
                                data->temp_max[ix] = vt1211_read8(data,
                                                regtempmax[ix]);
                                data->temp_hyst[ix] = vt1211_read8(data,
                                                regtemphyst[ix]);
                        }
                }

                /* fan & pwm registers */
                for (ix = 0; ix < ARRAY_SIZE(data->fan); ix++) {
                        data->fan[ix] = vt1211_read8(data,
                                                VT1211_REG_FAN(ix));
                        data->fan_min[ix] = vt1211_read8(data,
                                                VT1211_REG_FAN_MIN(ix));
                        data->pwm[ix] = vt1211_read8(data,
                                                VT1211_REG_PWM(ix));
                }
                val = vt1211_read8(data, VT1211_REG_FAN_DIV);
                data->fan_div[0] = (val >> 4) & 3;
                data->fan_div[1] = (val >> 6) & 3;
                data->fan_ctl = val & 0xf;

                val = vt1211_read8(data, VT1211_REG_PWM_CTL);
                data->pwm_ctl[0] = val & 0xf;
                data->pwm_ctl[1] = (val >> 4) & 0xf;

                data->pwm_clk = vt1211_read8(data, VT1211_REG_PWM_CLK);

                /* pwm & temp auto point registers */
                data->pwm_auto_pwm[0][1] = vt1211_read8(data,
                                                VT1211_REG_PWM_AUTO_PWM(0, 1));
                data->pwm_auto_pwm[0][2] = vt1211_read8(data,
                                                VT1211_REG_PWM_AUTO_PWM(0, 2));
                data->pwm_auto_pwm[1][1] = vt1211_read8(data,
                                                VT1211_REG_PWM_AUTO_PWM(1, 1));
                data->pwm_auto_pwm[1][2] = vt1211_read8(data,
                                                VT1211_REG_PWM_AUTO_PWM(1, 2));
                for (ix = 0; ix < ARRAY_SIZE(data->pwm_auto_temp); ix++) {
                        data->pwm_auto_temp[ix] = vt1211_read8(data,
                                                VT1211_REG_PWM_AUTO_TEMP(ix));
                }

                /* alarm registers */
                data->alarms = (vt1211_read8(data, VT1211_REG_ALARM2) << 8) |
                                vt1211_read8(data, VT1211_REG_ALARM1);

                data->last_updated = jiffies;
                data->valid = true;
        }

        mutex_unlock(&data->update_lock);

        return data;
}

/* ---------------------------------------------------------------------
 * Voltage sysfs interfaces
 * ix = [0-5]
 * --------------------------------------------------------------------- */

#define SHOW_IN_INPUT   0
#define SHOW_SET_IN_MIN 1
#define SHOW_SET_IN_MAX 2
#define SHOW_IN_ALARM   3

static ssize_t show_in(struct device *dev, struct device_attribute *attr,
                       char *buf)
{
        struct vt1211_data *data = vt1211_update_device(dev);
        struct sensor_device_attribute_2 *sensor_attr_2 =
                                                to_sensor_dev_attr_2(attr);
        int ix = sensor_attr_2->index;
        int fn = sensor_attr_2->nr;
        int res;

        switch (fn) {
        case SHOW_IN_INPUT:
                res = in_from_reg(ix, data->in[ix]);
                break;
        case SHOW_SET_IN_MIN:
                res = in_from_reg(ix, data->in_min[ix]);
                break;
        case SHOW_SET_IN_MAX:
                res = in_from_reg(ix, data->in_max[ix]);
                break;
        case SHOW_IN_ALARM:
                res = (data->alarms >> bitalarmin[ix]) & 1;
                break;
        default:
                res = 0;
                dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
        }

        return sprintf(buf, "%d\n", res);
}

static ssize_t set_in(struct device *dev, struct device_attribute *attr,
                      const char *buf, size_t count)
{
        struct vt1211_data *data = dev_get_drvdata(dev);
        struct sensor_device_attribute_2 *sensor_attr_2 =
                                                to_sensor_dev_attr_2(attr);
        int ix = sensor_attr_2->index;
        int fn = sensor_attr_2->nr;
        long val;
        int err;

        err = kstrtol(buf, 10, &val);
        if (err)
                return err;

        mutex_lock(&data->update_lock);
        switch (fn) {
        case SHOW_SET_IN_MIN:
                data->in_min[ix] = IN_TO_REG(ix, val);
                vt1211_write8(data, VT1211_REG_IN_MIN(ix), data->in_min[ix]);
                break;
        case SHOW_SET_IN_MAX:
                data->in_max[ix] = IN_TO_REG(ix, val);
                vt1211_write8(data, VT1211_REG_IN_MAX(ix), data->in_max[ix]);
                break;
        default:
                dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
        }
        mutex_unlock(&data->update_lock);

        return count;
}

/* ---------------------------------------------------------------------
 * Temperature sysfs interfaces
 * ix = [0-6]
 * --------------------------------------------------------------------- */

#define SHOW_TEMP_INPUT         0
#define SHOW_SET_TEMP_MAX       1
#define SHOW_SET_TEMP_MAX_HYST  2
#define SHOW_TEMP_ALARM         3

static ssize_t show_temp(struct device *dev, struct device_attribute *attr,
                         char *buf)
{
        struct vt1211_data *data = vt1211_update_device(dev);
        struct sensor_device_attribute_2 *sensor_attr_2 =
                                                to_sensor_dev_attr_2(attr);
        int ix = sensor_attr_2->index;
        int fn = sensor_attr_2->nr;
        int res;

        switch (fn) {
        case SHOW_TEMP_INPUT:
                res = temp_from_reg(ix, data->temp[ix]);
                break;
        case SHOW_SET_TEMP_MAX:
                res = temp_from_reg(ix, data->temp_max[ix]);
                break;
        case SHOW_SET_TEMP_MAX_HYST:
                res = temp_from_reg(ix, data->temp_hyst[ix]);
                break;
        case SHOW_TEMP_ALARM:
                res = (data->alarms >> bitalarmtemp[ix]) & 1;
                break;
        default:
                res = 0;
                dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
        }

        return sprintf(buf, "%d\n", res);
}

static ssize_t set_temp(struct device *dev, struct device_attribute *attr,
                        const char *buf, size_t count)
{
        struct vt1211_data *data = dev_get_drvdata(dev);
        struct sensor_device_attribute_2 *sensor_attr_2 =
                                                to_sensor_dev_attr_2(attr);
        int ix = sensor_attr_2->index;
        int fn = sensor_attr_2->nr;
        long val;
        int err;

        err = kstrtol(buf, 10, &val);
        if (err)
                return err;

        mutex_lock(&data->update_lock);
        switch (fn) {
        case SHOW_SET_TEMP_MAX:
                data->temp_max[ix] = TEMP_TO_REG(ix, val);
                vt1211_write8(data, regtempmax[ix],
                              data->temp_max[ix]);
                break;
        case SHOW_SET_TEMP_MAX_HYST:
                data->temp_hyst[ix] = TEMP_TO_REG(ix, val);
                vt1211_write8(data, regtemphyst[ix],
                              data->temp_hyst[ix]);
                break;
        default:
                dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
        }
        mutex_unlock(&data->update_lock);

        return count;
}

/* ---------------------------------------------------------------------
 * Fan sysfs interfaces
 * ix = [0-1]
 * --------------------------------------------------------------------- */

#define SHOW_FAN_INPUT          0
#define SHOW_SET_FAN_MIN        1
#define SHOW_SET_FAN_DIV        2
#define SHOW_FAN_ALARM          3

static ssize_t show_fan(struct device *dev, struct device_attribute *attr,
                        char *buf)
{
        struct vt1211_data *data = vt1211_update_device(dev);
        struct sensor_device_attribute_2 *sensor_attr_2 =
                                                to_sensor_dev_attr_2(attr);
        int ix = sensor_attr_2->index;
        int fn = sensor_attr_2->nr;
        int res;

        switch (fn) {
        case SHOW_FAN_INPUT:
                res = rpm_from_reg(data->fan[ix], data->fan_div[ix]);
                break;
        case SHOW_SET_FAN_MIN:
                res = rpm_from_reg(data->fan_min[ix], data->fan_div[ix]);
                break;
        case SHOW_SET_FAN_DIV:
                res = DIV_FROM_REG(data->fan_div[ix]);
                break;
        case SHOW_FAN_ALARM:
                res = (data->alarms >> bitalarmfan[ix]) & 1;
                break;
        default:
                res = 0;
                dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
        }

        return sprintf(buf, "%d\n", res);
}

static ssize_t set_fan(struct device *dev, struct device_attribute *attr,
                       const char *buf, size_t count)
{
        struct vt1211_data *data = dev_get_drvdata(dev);
        struct sensor_device_attribute_2 *sensor_attr_2 =
                                                to_sensor_dev_attr_2(attr);
        int ix = sensor_attr_2->index;
        int fn = sensor_attr_2->nr;
        int reg;
        unsigned long val;
        int err;

        err = kstrtoul(buf, 10, &val);
        if (err)
                return err;

        mutex_lock(&data->update_lock);

        /* sync the data cache */
        reg = vt1211_read8(data, VT1211_REG_FAN_DIV);
        data->fan_div[0] = (reg >> 4) & 3;
        data->fan_div[1] = (reg >> 6) & 3;
        data->fan_ctl = reg & 0xf;

        switch (fn) {
        case SHOW_SET_FAN_MIN:
                data->fan_min[ix] = RPM_TO_REG(val, data->fan_div[ix]);
                vt1211_write8(data, VT1211_REG_FAN_MIN(ix),
                              data->fan_min[ix]);
                break;
        case SHOW_SET_FAN_DIV:
                switch (val) {
                case 1:
                        data->fan_div[ix] = 0;
                        break;
                case 2:
                        data->fan_div[ix] = 1;
                        break;
                case 4:
                        data->fan_div[ix] = 2;
                        break;
                case 8:
                        data->fan_div[ix] = 3;
                        break;
                default:
                        count = -EINVAL;
                        dev_warn(dev,
                                 "fan div value %ld not supported. Choose one of 1, 2, 4, or 8.\n",
                                 val);
                        goto EXIT;
                }
                vt1211_write8(data, VT1211_REG_FAN_DIV,
                              ((data->fan_div[1] << 6) |
                               (data->fan_div[0] << 4) |
                                data->fan_ctl));
                break;
        default:
                dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
        }

EXIT:
        mutex_unlock(&data->update_lock);
        return count;
}

/* ---------------------------------------------------------------------
 * PWM sysfs interfaces
 * ix = [0-1]
 * --------------------------------------------------------------------- */

#define SHOW_PWM                        0
#define SHOW_SET_PWM_ENABLE             1
#define SHOW_SET_PWM_FREQ               2
#define SHOW_SET_PWM_AUTO_CHANNELS_TEMP 3

static ssize_t show_pwm(struct device *dev, struct device_attribute *attr,
                        char *buf)
{
        struct vt1211_data *data = vt1211_update_device(dev);
        struct sensor_device_attribute_2 *sensor_attr_2 =
                                                to_sensor_dev_attr_2(attr);
        int ix = sensor_attr_2->index;
        int fn = sensor_attr_2->nr;
        int res;

        switch (fn) {
        case SHOW_PWM:
                res = data->pwm[ix];
                break;
        case SHOW_SET_PWM_ENABLE:
                res = ((data->pwm_ctl[ix] >> 3) & 1) ? 2 : 0;
                break;
        case SHOW_SET_PWM_FREQ:
                res = 90000 >> (data->pwm_clk & 7);
                break;
        case SHOW_SET_PWM_AUTO_CHANNELS_TEMP:
                res = (data->pwm_ctl[ix] & 7) + 1;
                break;
        default:
                res = 0;
                dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
        }

        return sprintf(buf, "%d\n", res);
}

static ssize_t set_pwm(struct device *dev, struct device_attribute *attr,
                       const char *buf, size_t count)
{
        struct vt1211_data *data = dev_get_drvdata(dev);
        struct sensor_device_attribute_2 *sensor_attr_2 =
                                                to_sensor_dev_attr_2(attr);
        int ix = sensor_attr_2->index;
        int fn = sensor_attr_2->nr;
        int tmp, reg;
        unsigned long val;
        int err;

        err = kstrtoul(buf, 10, &val);
        if (err)
                return err;

        mutex_lock(&data->update_lock);

        switch (fn) {
        case SHOW_SET_PWM_ENABLE:
                /* sync the data cache */
                reg = vt1211_read8(data, VT1211_REG_FAN_DIV);
                data->fan_div[0] = (reg >> 4) & 3;
                data->fan_div[1] = (reg >> 6) & 3;
                data->fan_ctl = reg & 0xf;
                reg = vt1211_read8(data, VT1211_REG_PWM_CTL);
                data->pwm_ctl[0] = reg & 0xf;
                data->pwm_ctl[1] = (reg >> 4) & 0xf;
                switch (val) {
                case 0:
                        data->pwm_ctl[ix] &= 7;
                        /*
                         * disable SmartGuardian if both PWM outputs are
                         * disabled
                         */
                        if ((data->pwm_ctl[ix ^ 1] & 1) == 0)
                                data->fan_ctl &= 0xe;
                        break;
                case 2:
                        data->pwm_ctl[ix] |= 8;
                        data->fan_ctl |= 1;
                        break;
                default:
                        count = -EINVAL;
                        dev_warn(dev,
                                 "pwm mode %ld not supported. Choose one of 0 or 2.\n",
                                 val);
                        goto EXIT;
                }
                vt1211_write8(data, VT1211_REG_PWM_CTL,
                              ((data->pwm_ctl[1] << 4) |
                                data->pwm_ctl[0]));
                vt1211_write8(data, VT1211_REG_FAN_DIV,
                              ((data->fan_div[1] << 6) |
                               (data->fan_div[0] << 4) |
                                data->fan_ctl));
                break;
        case SHOW_SET_PWM_FREQ:
                val = 135000 / clamp_val(val, 135000 >> 7, 135000);
                /* calculate tmp = log2(val) */
                tmp = 0;
                for (val >>= 1; val > 0; val >>= 1)
                        tmp++;
                /* sync the data cache */
                reg = vt1211_read8(data, VT1211_REG_PWM_CLK);
                data->pwm_clk = (reg & 0xf8) | tmp;
                vt1211_write8(data, VT1211_REG_PWM_CLK, data->pwm_clk);
                break;
        case SHOW_SET_PWM_AUTO_CHANNELS_TEMP:
                if (val < 1 || val > 7) {
                        count = -EINVAL;
                        dev_warn(dev,
                                 "temp channel %ld not supported. Choose a value between 1 and 7.\n",
                                 val);
                        goto EXIT;
                }
                if (!ISTEMP(val - 1, data->uch_config)) {
                        count = -EINVAL;
                        dev_warn(dev, "temp channel %ld is not available.\n",
                                 val);
                        goto EXIT;
                }
                /* sync the data cache */
                reg = vt1211_read8(data, VT1211_REG_PWM_CTL);
                data->pwm_ctl[0] = reg & 0xf;
                data->pwm_ctl[1] = (reg >> 4) & 0xf;
                data->pwm_ctl[ix] = (data->pwm_ctl[ix] & 8) | (val - 1);
                vt1211_write8(data, VT1211_REG_PWM_CTL,
                              ((data->pwm_ctl[1] << 4) | data->pwm_ctl[0]));
                break;
        default:
                dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
        }

EXIT:
        mutex_unlock(&data->update_lock);
        return count;
}

/* ---------------------------------------------------------------------
 * PWM auto point definitions
 * ix = [0-1]
 * ap = [0-3]
 * --------------------------------------------------------------------- */

/*
 * pwm[ix+1]_auto_point[ap+1]_temp mapping table:
 * Note that there is only a single set of temp auto points that controls both
 * PWM controllers. We still create 2 sets of sysfs files to make it look
 * more consistent even though they map to the same registers.
 *
 * ix ap : description
 * -------------------
 * 0  0  : pwm1/2 off temperature        (pwm_auto_temp[0])
 * 0  1  : pwm1/2 low speed temperature  (pwm_auto_temp[1])
 * 0  2  : pwm1/2 high speed temperature (pwm_auto_temp[2])
 * 0  3  : pwm1/2 full speed temperature (pwm_auto_temp[3])
 * 1  0  : pwm1/2 off temperature        (pwm_auto_temp[0])
 * 1  1  : pwm1/2 low speed temperature  (pwm_auto_temp[1])
 * 1  2  : pwm1/2 high speed temperature (pwm_auto_temp[2])
 * 1  3  : pwm1/2 full speed temperature (pwm_auto_temp[3])
 */

static ssize_t show_pwm_auto_point_temp(struct device *dev,
                                        struct device_attribute *attr,
                                        char *buf)
{
        struct vt1211_data *data = vt1211_update_device(dev);
        struct sensor_device_attribute_2 *sensor_attr_2 =
                                                to_sensor_dev_attr_2(attr);
        int ix = sensor_attr_2->index;
        int ap = sensor_attr_2->nr;

        return sprintf(buf, "%d\n", temp_from_reg(data->pwm_ctl[ix] & 7,
                       data->pwm_auto_temp[ap]));
}

static ssize_t set_pwm_auto_point_temp(struct device *dev,
                                       struct device_attribute *attr,
                                       const char *buf, size_t count)
{
        struct vt1211_data *data = dev_get_drvdata(dev);
        struct sensor_device_attribute_2 *sensor_attr_2 =
                                                to_sensor_dev_attr_2(attr);
        int ix = sensor_attr_2->index;
        int ap = sensor_attr_2->nr;
        int reg;
        long val;
        int err;

        err = kstrtol(buf, 10, &val);
        if (err)
                return err;


        mutex_lock(&data->update_lock);

        /* sync the data cache */
        reg = vt1211_read8(data, VT1211_REG_PWM_CTL);
        data->pwm_ctl[0] = reg & 0xf;
        data->pwm_ctl[1] = (reg >> 4) & 0xf;

        data->pwm_auto_temp[ap] = TEMP_TO_REG(data->pwm_ctl[ix] & 7, val);
        vt1211_write8(data, VT1211_REG_PWM_AUTO_TEMP(ap),
                      data->pwm_auto_temp[ap]);
        mutex_unlock(&data->update_lock);

        return count;
}

/*
 * pwm[ix+1]_auto_point[ap+1]_pwm mapping table:
 * Note that the PWM auto points 0 & 3 are hard-wired in the VT1211 and can't
 * be changed.
 *
 * ix ap : description
 * -------------------
 * 0  0  : pwm1 off                   (pwm_auto_pwm[0][0], hard-wired to 0)
 * 0  1  : pwm1 low speed duty cycle  (pwm_auto_pwm[0][1])
 * 0  2  : pwm1 high speed duty cycle (pwm_auto_pwm[0][2])
 * 0  3  : pwm1 full speed            (pwm_auto_pwm[0][3], hard-wired to 255)
 * 1  0  : pwm2 off                   (pwm_auto_pwm[1][0], hard-wired to 0)
 * 1  1  : pwm2 low speed duty cycle  (pwm_auto_pwm[1][1])
 * 1  2  : pwm2 high speed duty cycle (pwm_auto_pwm[1][2])
 * 1  3  : pwm2 full speed            (pwm_auto_pwm[1][3], hard-wired to 255)
 */

static ssize_t show_pwm_auto_point_pwm(struct device *dev,
                                       struct device_attribute *attr,
                                       char *buf)
{
        struct vt1211_data *data = vt1211_update_device(dev);
        struct sensor_device_attribute_2 *sensor_attr_2 =
                                                to_sensor_dev_attr_2(attr);
        int ix = sensor_attr_2->index;
        int ap = sensor_attr_2->nr;

        return sprintf(buf, "%d\n", data->pwm_auto_pwm[ix][ap]);
}

static ssize_t set_pwm_auto_point_pwm(struct device *dev,
                                      struct device_attribute *attr,
                                      const char *buf, size_t count)
{
        struct vt1211_data *data = dev_get_drvdata(dev);
        struct sensor_device_attribute_2 *sensor_attr_2 =
                                                to_sensor_dev_attr_2(attr);
        int ix = sensor_attr_2->index;
        int ap = sensor_attr_2->nr;
        unsigned long val;
        int err;

        err = kstrtoul(buf, 10, &val);
        if (err)
                return err;

        mutex_lock(&data->update_lock);
        data->pwm_auto_pwm[ix][ap] = clamp_val(val, 0, 255);
        vt1211_write8(data, VT1211_REG_PWM_AUTO_PWM(ix, ap),
                      data->pwm_auto_pwm[ix][ap]);
        mutex_unlock(&data->update_lock);

        return count;
}

/* ---------------------------------------------------------------------
 * Miscellaneous sysfs interfaces (VRM, VID, name, and (legacy) alarms)
 * --------------------------------------------------------------------- */

static ssize_t show_vrm(struct device *dev, struct device_attribute *attr,
                        char *buf)
{
        struct vt1211_data *data = dev_get_drvdata(dev);

        return sprintf(buf, "%d\n", data->vrm);
}

static ssize_t set_vrm(struct device *dev, struct device_attribute *attr,
                       const char *buf, size_t count)
{
        struct vt1211_data *data = dev_get_drvdata(dev);
        unsigned long val;
        int err;

        err = kstrtoul(buf, 10, &val);
        if (err)
                return err;

        if (val > 255)
                return -EINVAL;

        data->vrm = val;

        return count;
}

static ssize_t show_vid(struct device *dev, struct device_attribute *attr,
                        char *buf)
{
        struct vt1211_data *data = dev_get_drvdata(dev);

        return sprintf(buf, "%d\n", vid_from_reg(data->vid, data->vrm));
}

static ssize_t show_name(struct device *dev,
                         struct device_attribute *attr, char *buf)
{
        struct vt1211_data *data = dev_get_drvdata(dev);

        return sprintf(buf, "%s\n", data->name);
}

static ssize_t show_alarms(struct device *dev,
                           struct device_attribute *attr, char *buf)
{
        struct vt1211_data *data = vt1211_update_device(dev);

        return sprintf(buf, "%d\n", data->alarms);
}

/* ---------------------------------------------------------------------
 * Device attribute structs
 * --------------------------------------------------------------------- */

#define SENSOR_ATTR_IN(ix) \
{       SENSOR_ATTR_2(in##ix##_input, S_IRUGO, \
                show_in, NULL, SHOW_IN_INPUT, ix), \
        SENSOR_ATTR_2(in##ix##_min, S_IRUGO | S_IWUSR, \
                show_in, set_in, SHOW_SET_IN_MIN, ix), \
        SENSOR_ATTR_2(in##ix##_max, S_IRUGO | S_IWUSR, \
                show_in, set_in, SHOW_SET_IN_MAX, ix), \
        SENSOR_ATTR_2(in##ix##_alarm, S_IRUGO, \
                show_in, NULL, SHOW_IN_ALARM, ix) \
}

static struct sensor_device_attribute_2 vt1211_sysfs_in[][4] = {
        SENSOR_ATTR_IN(0),
        SENSOR_ATTR_IN(1),
        SENSOR_ATTR_IN(2),
        SENSOR_ATTR_IN(3),
        SENSOR_ATTR_IN(4),
        SENSOR_ATTR_IN(5)
};

#define IN_UNIT_ATTRS(X)                        \
{       &vt1211_sysfs_in[X][0].dev_attr.attr,   \
        &vt1211_sysfs_in[X][1].dev_attr.attr,   \
        &vt1211_sysfs_in[X][2].dev_attr.attr,   \
        &vt1211_sysfs_in[X][3].dev_attr.attr,   \
        NULL                                    \
}

static struct attribute *vt1211_in_attr[][5] = {
        IN_UNIT_ATTRS(0),
        IN_UNIT_ATTRS(1),
        IN_UNIT_ATTRS(2),
        IN_UNIT_ATTRS(3),
        IN_UNIT_ATTRS(4),
        IN_UNIT_ATTRS(5)
};

static const struct attribute_group vt1211_in_attr_group[] = {
        { .attrs = vt1211_in_attr[0] },
        { .attrs = vt1211_in_attr[1] },
        { .attrs = vt1211_in_attr[2] },
        { .attrs = vt1211_in_attr[3] },
        { .attrs = vt1211_in_attr[4] },
        { .attrs = vt1211_in_attr[5] }
};

#define SENSOR_ATTR_TEMP(ix) \
{       SENSOR_ATTR_2(temp##ix##_input, S_IRUGO, \
                show_temp, NULL, SHOW_TEMP_INPUT, ix-1), \
        SENSOR_ATTR_2(temp##ix##_max, S_IRUGO | S_IWUSR, \
                show_temp, set_temp, SHOW_SET_TEMP_MAX, ix-1), \
        SENSOR_ATTR_2(temp##ix##_max_hyst, S_IRUGO | S_IWUSR, \
                show_temp, set_temp, SHOW_SET_TEMP_MAX_HYST, ix-1), \
        SENSOR_ATTR_2(temp##ix##_alarm, S_IRUGO, \
                show_temp, NULL, SHOW_TEMP_ALARM, ix-1) \
}

static struct sensor_device_attribute_2 vt1211_sysfs_temp[][4] = {
        SENSOR_ATTR_TEMP(1),
        SENSOR_ATTR_TEMP(2),
        SENSOR_ATTR_TEMP(3),
        SENSOR_ATTR_TEMP(4),
        SENSOR_ATTR_TEMP(5),
        SENSOR_ATTR_TEMP(6),
        SENSOR_ATTR_TEMP(7),
};

#define TEMP_UNIT_ATTRS(X)                      \
{       &vt1211_sysfs_temp[X][0].dev_attr.attr, \
        &vt1211_sysfs_temp[X][1].dev_attr.attr, \
        &vt1211_sysfs_temp[X][2].dev_attr.attr, \
        &vt1211_sysfs_temp[X][3].dev_attr.attr, \
        NULL                                    \
}

static struct attribute *vt1211_temp_attr[][5] = {
        TEMP_UNIT_ATTRS(0),
        TEMP_UNIT_ATTRS(1),
        TEMP_UNIT_ATTRS(2),
        TEMP_UNIT_ATTRS(3),
        TEMP_UNIT_ATTRS(4),
        TEMP_UNIT_ATTRS(5),
        TEMP_UNIT_ATTRS(6)
};

static const struct attribute_group vt1211_temp_attr_group[] = {
        { .attrs = vt1211_temp_attr[0] },
        { .attrs = vt1211_temp_attr[1] },
        { .attrs = vt1211_temp_attr[2] },
        { .attrs = vt1211_temp_attr[3] },
        { .attrs = vt1211_temp_attr[4] },
        { .attrs = vt1211_temp_attr[5] },
        { .attrs = vt1211_temp_attr[6] }
};

#define SENSOR_ATTR_FAN(ix) \
        SENSOR_ATTR_2(fan##ix##_input, S_IRUGO, \
                show_fan, NULL, SHOW_FAN_INPUT, ix-1), \
        SENSOR_ATTR_2(fan##ix##_min, S_IRUGO | S_IWUSR, \
                show_fan, set_fan, SHOW_SET_FAN_MIN, ix-1), \
        SENSOR_ATTR_2(fan##ix##_div, S_IRUGO | S_IWUSR, \
                show_fan, set_fan, SHOW_SET_FAN_DIV, ix-1), \
        SENSOR_ATTR_2(fan##ix##_alarm, S_IRUGO, \
                show_fan, NULL, SHOW_FAN_ALARM, ix-1)

#define SENSOR_ATTR_PWM(ix) \
        SENSOR_ATTR_2(pwm##ix, S_IRUGO, \
                show_pwm, NULL, SHOW_PWM, ix-1), \
        SENSOR_ATTR_2(pwm##ix##_enable, S_IRUGO | S_IWUSR, \
                show_pwm, set_pwm, SHOW_SET_PWM_ENABLE, ix-1), \
        SENSOR_ATTR_2(pwm##ix##_auto_channels_temp, S_IRUGO | S_IWUSR, \
                show_pwm, set_pwm, SHOW_SET_PWM_AUTO_CHANNELS_TEMP, ix-1)

#define SENSOR_ATTR_PWM_FREQ(ix) \
        SENSOR_ATTR_2(pwm##ix##_freq, S_IRUGO | S_IWUSR, \
                show_pwm, set_pwm, SHOW_SET_PWM_FREQ, ix-1)

#define SENSOR_ATTR_PWM_FREQ_RO(ix) \
        SENSOR_ATTR_2(pwm##ix##_freq, S_IRUGO, \
                show_pwm, NULL, SHOW_SET_PWM_FREQ, ix-1)

#define SENSOR_ATTR_PWM_AUTO_POINT_TEMP(ix, ap) \
        SENSOR_ATTR_2(pwm##ix##_auto_point##ap##_temp, S_IRUGO | S_IWUSR, \
                show_pwm_auto_point_temp, set_pwm_auto_point_temp, \
                ap-1, ix-1)

#define SENSOR_ATTR_PWM_AUTO_POINT_TEMP_RO(ix, ap) \
        SENSOR_ATTR_2(pwm##ix##_auto_point##ap##_temp, S_IRUGO, \
                show_pwm_auto_point_temp, NULL, \
                ap-1, ix-1)

#define SENSOR_ATTR_PWM_AUTO_POINT_PWM(ix, ap) \
        SENSOR_ATTR_2(pwm##ix##_auto_point##ap##_pwm, S_IRUGO | S_IWUSR, \
                show_pwm_auto_point_pwm, set_pwm_auto_point_pwm, \
                ap-1, ix-1)

#define SENSOR_ATTR_PWM_AUTO_POINT_PWM_RO(ix, ap) \
        SENSOR_ATTR_2(pwm##ix##_auto_point##ap##_pwm, S_IRUGO, \
                show_pwm_auto_point_pwm, NULL, \
                ap-1, ix-1)

static struct sensor_device_attribute_2 vt1211_sysfs_fan_pwm[] = {
        SENSOR_ATTR_FAN(1),
        SENSOR_ATTR_FAN(2),
        SENSOR_ATTR_PWM(1),
        SENSOR_ATTR_PWM(2),
        SENSOR_ATTR_PWM_FREQ(1),
        SENSOR_ATTR_PWM_FREQ_RO(2),
        SENSOR_ATTR_PWM_AUTO_POINT_TEMP(1, 1),
        SENSOR_ATTR_PWM_AUTO_POINT_TEMP(1, 2),
        SENSOR_ATTR_PWM_AUTO_POINT_TEMP(1, 3),
        SENSOR_ATTR_PWM_AUTO_POINT_TEMP(1, 4),
        SENSOR_ATTR_PWM_AUTO_POINT_TEMP_RO(2, 1),
        SENSOR_ATTR_PWM_AUTO_POINT_TEMP_RO(2, 2),
        SENSOR_ATTR_PWM_AUTO_POINT_TEMP_RO(2, 3),
        SENSOR_ATTR_PWM_AUTO_POINT_TEMP_RO(2, 4),
        SENSOR_ATTR_PWM_AUTO_POINT_PWM_RO(1, 1),
        SENSOR_ATTR_PWM_AUTO_POINT_PWM(1, 2),
        SENSOR_ATTR_PWM_AUTO_POINT_PWM(1, 3),
        SENSOR_ATTR_PWM_AUTO_POINT_PWM_RO(1, 4),
        SENSOR_ATTR_PWM_AUTO_POINT_PWM_RO(2, 1),
        SENSOR_ATTR_PWM_AUTO_POINT_PWM(2, 2),
        SENSOR_ATTR_PWM_AUTO_POINT_PWM(2, 3),
        SENSOR_ATTR_PWM_AUTO_POINT_PWM_RO(2, 4),
};

static struct device_attribute vt1211_sysfs_misc[] = {
        __ATTR(vrm, S_IRUGO | S_IWUSR, show_vrm, set_vrm),
        __ATTR(cpu0_vid, S_IRUGO, show_vid, NULL),
        __ATTR(name, S_IRUGO, show_name, NULL),
        __ATTR(alarms, S_IRUGO, show_alarms, NULL),
};

/* ---------------------------------------------------------------------
 * Device registration and initialization
 * --------------------------------------------------------------------- */

static void vt1211_init_device(struct vt1211_data *data)
{
        /* set VRM */
        data->vrm = vid_which_vrm();

        /* Read (and initialize) UCH config */
        data->uch_config = vt1211_read8(data, VT1211_REG_UCH_CONFIG);
        if (uch_config > -1) {
                data->uch_config = (data->uch_config & 0x83) |
                                   (uch_config << 2);
                vt1211_write8(data, VT1211_REG_UCH_CONFIG, data->uch_config);
        }

        /*
         * Initialize the interrupt mode (if request at module load time).
         * The VT1211 implements 3 different modes for clearing interrupts:
         * 0: Clear INT when status register is read. Regenerate INT as long
         *    as temp stays above hysteresis limit.
         * 1: Clear INT when status register is read. DON'T regenerate INT
         *    until temp falls below hysteresis limit and exceeds hot limit
         *    again.
         * 2: Clear INT when temp falls below max limit.
         *
         * The driver only allows to force mode 0 since that's the only one
         * that makes sense for 'sensors'
         */
        if (int_mode == 0) {
                vt1211_write8(data, VT1211_REG_TEMP1_CONFIG, 0);
                vt1211_write8(data, VT1211_REG_TEMP2_CONFIG, 0);
        }

        /* Fill in some hard wired values into our data struct */
        data->pwm_auto_pwm[0][3] = 255;
        data->pwm_auto_pwm[1][3] = 255;
}

static void vt1211_remove_sysfs(struct platform_device *pdev)
{
        struct device *dev = &pdev->dev;
        int i;

        for (i = 0; i < ARRAY_SIZE(vt1211_in_attr_group); i++)
                sysfs_remove_group(&dev->kobj, &vt1211_in_attr_group[i]);

        for (i = 0; i < ARRAY_SIZE(vt1211_temp_attr_group); i++)
                sysfs_remove_group(&dev->kobj, &vt1211_temp_attr_group[i]);

        for (i = 0; i < ARRAY_SIZE(vt1211_sysfs_fan_pwm); i++) {
                device_remove_file(dev,
                        &vt1211_sysfs_fan_pwm[i].dev_attr);
        }
        for (i = 0; i < ARRAY_SIZE(vt1211_sysfs_misc); i++)
                device_remove_file(dev, &vt1211_sysfs_misc[i]);
}

static int vt1211_probe(struct platform_device *pdev)
{
        struct device *dev = &pdev->dev;
        struct vt1211_data *data;
        struct resource *res;
        int i, err;

        data = devm_kzalloc(dev, sizeof(struct vt1211_data), GFP_KERNEL);
        if (!data)
                return -ENOMEM;

        res = platform_get_resource(pdev, IORESOURCE_IO, 0);
        if (!devm_request_region(dev, res->start, resource_size(res),
                                 DRVNAME)) {
                dev_err(dev, "Failed to request region 0x%lx-0x%lx\n",
                        (unsigned long)res->start, (unsigned long)res->end);
                return -EBUSY;
        }
        data->addr = res->start;
        data->name = DRVNAME;
        mutex_init(&data->update_lock);

        platform_set_drvdata(pdev, data);

        /* Initialize the VT1211 chip */
        vt1211_init_device(data);

        /* Create sysfs interface files */
        for (i = 0; i < ARRAY_SIZE(vt1211_in_attr_group); i++) {
                if (ISVOLT(i, data->uch_config)) {
                        err = sysfs_create_group(&dev->kobj,
                                                 &vt1211_in_attr_group[i]);
                        if (err)
                                goto EXIT_DEV_REMOVE;
                }
        }
        for (i = 0; i < ARRAY_SIZE(vt1211_temp_attr_group); i++) {
                if (ISTEMP(i, data->uch_config)) {
                        err = sysfs_create_group(&dev->kobj,
                                                 &vt1211_temp_attr_group[i]);
                        if (err)
                                goto EXIT_DEV_REMOVE;
                }
        }
        for (i = 0; i < ARRAY_SIZE(vt1211_sysfs_fan_pwm); i++) {
                err = device_create_file(dev,
                        &vt1211_sysfs_fan_pwm[i].dev_attr);
                if (err)
                        goto EXIT_DEV_REMOVE;
        }
        for (i = 0; i < ARRAY_SIZE(vt1211_sysfs_misc); i++) {
                err = device_create_file(dev,
                       &vt1211_sysfs_misc[i]);
                if (err)
                        goto EXIT_DEV_REMOVE;
        }

        /* Register device */
        data->hwmon_dev = hwmon_device_register(dev);
        if (IS_ERR(data->hwmon_dev)) {
                err = PTR_ERR(data->hwmon_dev);
                dev_err(dev, "Class registration failed (%d)\n", err);
                goto EXIT_DEV_REMOVE_SILENT;
        }

        return 0;

EXIT_DEV_REMOVE:
        dev_err(dev, "Sysfs interface creation failed (%d)\n", err);
EXIT_DEV_REMOVE_SILENT:
        vt1211_remove_sysfs(pdev);
        return err;
}

static void vt1211_remove(struct platform_device *pdev)
{
        struct vt1211_data *data = platform_get_drvdata(pdev);

        hwmon_device_unregister(data->hwmon_dev);
        vt1211_remove_sysfs(pdev);
}

static struct platform_driver vt1211_driver = {
        .driver = {
                .name  = DRVNAME,
        },
        .probe  = vt1211_probe,
        .remove = vt1211_remove,
};

static int __init vt1211_device_add(unsigned short address)
{
        struct resource res = {
                .start  = address,
                .end    = address + 0x7f,
                .flags  = IORESOURCE_IO,
        };
        int err;

        pdev = platform_device_alloc(DRVNAME, address);
        if (!pdev) {
                err = -ENOMEM;
                pr_err("Device allocation failed (%d)\n", err);
                goto EXIT;
        }

        res.name = pdev->name;
        err = acpi_check_resource_conflict(&res);
        if (err)
                goto EXIT_DEV_PUT;

        err = platform_device_add_resources(pdev, &res, 1);
        if (err) {
                pr_err("Device resource addition failed (%d)\n", err);
                goto EXIT_DEV_PUT;
        }

        err = platform_device_add(pdev);
        if (err) {
                pr_err("Device addition failed (%d)\n", err);
                goto EXIT_DEV_PUT;
        }

        return 0;

EXIT_DEV_PUT:
        platform_device_put(pdev);
EXIT:
        return err;
}

static int __init vt1211_find(int sio_cip, unsigned short *address)
{
        int err;
        int devid;

        err = superio_enter(sio_cip);
        if (err)
                return err;

        err = -ENODEV;
        devid = force_id ? force_id : superio_inb(sio_cip, SIO_VT1211_DEVID);
        if (devid != SIO_VT1211_ID)
                goto EXIT;

        superio_select(sio_cip, SIO_VT1211_LDN_HWMON);

        if ((superio_inb(sio_cip, SIO_VT1211_ACTIVE) & 1) == 0) {
                pr_warn("HW monitor is disabled, skipping\n");
                goto EXIT;
        }

        *address = ((superio_inb(sio_cip, SIO_VT1211_BADDR) << 8) |
                    (superio_inb(sio_cip, SIO_VT1211_BADDR + 1))) & 0xff00;
        if (*address == 0) {
                pr_warn("Base address is not set, skipping\n");
                goto EXIT;
        }

        err = 0;
        pr_info("Found VT1211 chip at 0x%04x, revision %u\n",
                *address, superio_inb(sio_cip, SIO_VT1211_DEVREV));

EXIT:
        superio_exit(sio_cip);
        return err;
}

static int __init vt1211_init(void)
{
        int err;
        unsigned short address = 0;

        err = vt1211_find(SIO_REG_CIP1, &address);
        if (err) {
                err = vt1211_find(SIO_REG_CIP2, &address);
                if (err)
                        goto EXIT;
        }

        if ((uch_config < -1) || (uch_config > 31)) {
                err = -EINVAL;
                pr_warn("Invalid UCH configuration %d. Choose a value between 0 and 31.\n",
                        uch_config);
                goto EXIT;
        }

        if ((int_mode < -1) || (int_mode > 0)) {
                err = -EINVAL;
                pr_warn("Invalid interrupt mode %d. Only mode 0 is supported.\n",
                        int_mode);
                goto EXIT;
        }

        err = platform_driver_register(&vt1211_driver);
        if (err)
                goto EXIT;

        /* Sets global pdev as a side effect */
        err = vt1211_device_add(address);
        if (err)
                goto EXIT_DRV_UNREGISTER;

        return 0;

EXIT_DRV_UNREGISTER:
        platform_driver_unregister(&vt1211_driver);
EXIT:
        return err;
}

static void __exit vt1211_exit(void)
{
        platform_device_unregister(pdev);
        platform_driver_unregister(&vt1211_driver);
}

MODULE_AUTHOR("Juerg Haefliger <juergh@gmail.com>");
MODULE_DESCRIPTION("VT1211 sensors");
MODULE_LICENSE("GPL");

module_init(vt1211_init);
module_exit(vt1211_exit);