// SPDX-License-Identifier: GPL-2.0
/*
 * Copyright (C) STMicroelectronics 2016
 *
 * Author: Gerald Baeza <gerald.baeza@st.com>
 *
 * Inspired by timer-stm32.c from Maxime Coquelin
 *             pwm-atmel.c from Bo Shen
 */

#include <linux/bitfield.h>
#include <linux/mfd/stm32-timers.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/pinctrl/consumer.h>
#include <linux/platform_device.h>
#include <linux/pwm.h>

#define CCMR_CHANNEL_SHIFT 8
#define CCMR_CHANNEL_MASK  0xFF
#define MAX_BREAKINPUT 2
#define STM32_MAX_PWM_OUTPUT 4

struct stm32_breakinput {
        u32 index;
        u32 level;
        u32 filter;
};

struct stm32_pwm {
        struct mutex lock; /* protect pwm config/enable */
        struct clk *clk;
        struct regmap *regmap;
        u32 max_arr;
        bool have_complementary_output;
        struct stm32_breakinput breakinputs[MAX_BREAKINPUT];
        unsigned int num_breakinputs;
        u32 capture[4] ____cacheline_aligned; /* DMA'able buffer */
};

static inline struct stm32_pwm *to_stm32_pwm_dev(struct pwm_chip *chip)
{
        return pwmchip_get_drvdata(chip);
}

static u32 active_channels(struct stm32_pwm *dev)
{
        u32 ccer;

        regmap_read(dev->regmap, TIM_CCER, &ccer);

        return ccer & TIM_CCER_CCXE;
}

struct stm32_pwm_waveform {
        u32 ccer;
        u32 psc;
        u32 arr;
        u32 ccr;
};

static int stm32_pwm_round_waveform_tohw(struct pwm_chip *chip,
                                         struct pwm_device *pwm,
                                         const struct pwm_waveform *wf,
                                         void *_wfhw)
{
        struct stm32_pwm_waveform *wfhw = _wfhw;
        struct stm32_pwm *priv = to_stm32_pwm_dev(chip);
        unsigned int ch = pwm->hwpwm;
        unsigned long rate;
        u64 ccr, duty;
        int ret;

        if (wf->period_length_ns == 0) {
                *wfhw = (struct stm32_pwm_waveform){
                        .ccer = 0,
                };

                return 0;
        }

        ret = clk_enable(priv->clk);
        if (ret)
                return ret;

        wfhw->ccer = TIM_CCER_CCxE(ch + 1);
        if (priv->have_complementary_output)
                wfhw->ccer |= TIM_CCER_CCxNE(ch + 1);

        rate = clk_get_rate(priv->clk);

        if (active_channels(priv) & ~TIM_CCER_CCxE(ch + 1)) {
                u64 arr;

                /*
                 * Other channels are already enabled, so the configured PSC and
                 * ARR must be used for this channel, too.
                 */
                ret = regmap_read(priv->regmap, TIM_PSC, &wfhw->psc);
                if (ret)
                        goto out;

                ret = regmap_read(priv->regmap, TIM_ARR, &wfhw->arr);
                if (ret)
                        goto out;

                arr = mul_u64_u64_div_u64(wf->period_length_ns, rate,
                                          (u64)NSEC_PER_SEC * (wfhw->psc + 1));
                if (arr <= wfhw->arr) {
                        /*
                         * requested period is smaller than the currently
                         * configured and unchangable period, report back the smallest
                         * possible period, i.e. the current state and return 1
                         * to indicate the wrong rounding direction.
                         */
                        ret = 1;
                }

        } else {
                /*
                 * .probe() asserted that clk_get_rate() is not bigger than 1 GHz, so
                 * the calculations here won't overflow.
                 * First we need to find the minimal value for prescaler such that
                 *
                 *        period_ns * clkrate
                 *   ------------------------------ < max_arr + 1
                 *   NSEC_PER_SEC * (prescaler + 1)
                 *
                 * This equation is equivalent to
                 *
                 *        period_ns * clkrate
                 *   ---------------------------- < prescaler + 1
                 *   NSEC_PER_SEC * (max_arr + 1)
                 *
                 * Using integer division and knowing that the right hand side is
                 * integer, this is further equivalent to
                 *
                 *   (period_ns * clkrate) // (NSEC_PER_SEC * (max_arr + 1)) ≤ prescaler
                 */
                u64 psc = mul_u64_u64_div_u64(wf->period_length_ns, rate,
                                              (u64)NSEC_PER_SEC * ((u64)priv->max_arr + 1));
                u64 arr;

                wfhw->psc = min_t(u64, psc, MAX_TIM_PSC);

                arr = mul_u64_u64_div_u64(wf->period_length_ns, rate,
                                          (u64)NSEC_PER_SEC * (wfhw->psc + 1));
                if (!arr) {
                        /*
                         * requested period is too small, report back the smallest
                         * possible period, i.e. ARR = 0. The only valid CCR
                         * value is then zero, too.
                         */
                        wfhw->arr = 0;
                        wfhw->ccr = 0;
                        ret = 1;
                        goto out;
                }

                /*
                 * ARR is limited intentionally to values less than
                 * priv->max_arr to allow 100% duty cycle.
                 */
                wfhw->arr = min_t(u64, arr, priv->max_arr) - 1;
        }

        duty = mul_u64_u64_div_u64(wf->duty_length_ns, rate,
                                   (u64)NSEC_PER_SEC * (wfhw->psc + 1));
        duty = min_t(u64, duty, wfhw->arr + 1);

        if (wf->duty_length_ns && wf->duty_offset_ns &&
            wf->duty_length_ns + wf->duty_offset_ns >= wf->period_length_ns) {
                wfhw->ccer |= TIM_CCER_CCxP(ch + 1);
                if (priv->have_complementary_output)
                        wfhw->ccer |= TIM_CCER_CCxNP(ch + 1);

                ccr = wfhw->arr + 1 - duty;
        } else {
                ccr = duty;
        }

        wfhw->ccr = min_t(u64, ccr, wfhw->arr + 1);

out:
        dev_dbg(&chip->dev, "pwm#%u: %lld/%lld [+%lld] @%lu -> CCER: %08x, PSC: %08x, ARR: %08x, CCR: %08x\n",
                pwm->hwpwm, wf->duty_length_ns, wf->period_length_ns, wf->duty_offset_ns,
                rate, wfhw->ccer, wfhw->psc, wfhw->arr, wfhw->ccr);

        clk_disable(priv->clk);

        return ret;
}

/*
 * This should be moved to lib/math/div64.c. Currently there are some changes
 * pending to mul_u64_u64_div_u64. Uwe will care for that when the dust settles.
 */
static u64 stm32_pwm_mul_u64_u64_div_u64_roundup(u64 a, u64 b, u64 c)
{
        u64 res = mul_u64_u64_div_u64(a, b, c);
        /* Those multiplications might overflow but it doesn't matter */
        u64 rem = a * b - c * res;

        if (rem)
                res += 1;

        return res;
}

static int stm32_pwm_round_waveform_fromhw(struct pwm_chip *chip,
                                           struct pwm_device *pwm,
                                           const void *_wfhw,
                                           struct pwm_waveform *wf)
{
        const struct stm32_pwm_waveform *wfhw = _wfhw;
        struct stm32_pwm *priv = to_stm32_pwm_dev(chip);
        unsigned long rate = clk_get_rate(priv->clk);
        unsigned int ch = pwm->hwpwm;

        if (wfhw->ccer & TIM_CCER_CCxE(ch + 1)) {
                u64 ccr_ns;

                /* The result doesn't overflow for rate >= 15259 */
                wf->period_length_ns = stm32_pwm_mul_u64_u64_div_u64_roundup(((u64)wfhw->psc + 1) * (wfhw->arr + 1),
                                                                             NSEC_PER_SEC, rate);

                ccr_ns = stm32_pwm_mul_u64_u64_div_u64_roundup(((u64)wfhw->psc + 1) * wfhw->ccr,
                                                               NSEC_PER_SEC, rate);

                if (wfhw->ccer & TIM_CCER_CCxP(ch + 1)) {
                        wf->duty_length_ns =
                                stm32_pwm_mul_u64_u64_div_u64_roundup(((u64)wfhw->psc + 1) * (wfhw->arr + 1 - wfhw->ccr),
                                                                      NSEC_PER_SEC, rate);

                        wf->duty_offset_ns = ccr_ns;
                } else {
                        wf->duty_length_ns = ccr_ns;
                        wf->duty_offset_ns = 0;
                }
        } else {
                *wf = (struct pwm_waveform){
                        .period_length_ns = 0,
                };
        }

        dev_dbg(&chip->dev, "pwm#%u: CCER: %08x, PSC: %08x, ARR: %08x, CCR: %08x @%lu -> %lld/%lld [+%lld]\n",
                pwm->hwpwm, wfhw->ccer, wfhw->psc, wfhw->arr, wfhw->ccr, rate,
                wf->duty_length_ns, wf->period_length_ns, wf->duty_offset_ns);

        return 0;
}

static int stm32_pwm_read_waveform(struct pwm_chip *chip,
                                     struct pwm_device *pwm,
                                     void *_wfhw)
{
        struct stm32_pwm_waveform *wfhw = _wfhw;
        struct stm32_pwm *priv = to_stm32_pwm_dev(chip);
        unsigned int ch = pwm->hwpwm;
        int ret;

        ret = clk_enable(priv->clk);
        if (ret)
                return ret;

        ret = regmap_read(priv->regmap, TIM_CCER, &wfhw->ccer);
        if (ret)
                goto out;

        if (wfhw->ccer & TIM_CCER_CCxE(ch + 1)) {
                ret = regmap_read(priv->regmap, TIM_PSC, &wfhw->psc);
                if (ret)
                        goto out;

                ret = regmap_read(priv->regmap, TIM_ARR, &wfhw->arr);
                if (ret)
                        goto out;

                if (wfhw->arr == U32_MAX)
                        wfhw->arr -= 1;

                ret = regmap_read(priv->regmap, TIM_CCRx(ch + 1), &wfhw->ccr);
                if (ret)
                        goto out;

                if (wfhw->ccr > wfhw->arr + 1)
                        wfhw->ccr = wfhw->arr + 1;
        }

out:
        clk_disable(priv->clk);

        return ret;
}

static int stm32_pwm_write_waveform(struct pwm_chip *chip,
                                      struct pwm_device *pwm,
                                      const void *_wfhw)
{
        const struct stm32_pwm_waveform *wfhw = _wfhw;
        struct stm32_pwm *priv = to_stm32_pwm_dev(chip);
        unsigned int ch = pwm->hwpwm;
        int ret;

        ret = clk_enable(priv->clk);
        if (ret)
                return ret;

        if (wfhw->ccer & TIM_CCER_CCxE(ch + 1)) {
                u32 ccer, mask;
                unsigned int shift;
                u32 ccmr;

                ret = regmap_read(priv->regmap, TIM_CCER, &ccer);
                if (ret)
                        goto out;

                /* If there are other channels enabled, don't update PSC and ARR */
                if (ccer & ~TIM_CCER_CCxE(ch + 1) & TIM_CCER_CCXE) {
                        u32 psc, arr;

                        ret = regmap_read(priv->regmap, TIM_PSC, &psc);
                        if (ret)
                                goto out;

                        if (psc != wfhw->psc) {
                                ret = -EBUSY;
                                goto out;
                        }

                        ret = regmap_read(priv->regmap, TIM_ARR, &arr);
                        if (ret)
                                goto out;

                        if (arr != wfhw->arr) {
                                ret = -EBUSY;
                                goto out;
                        }
                } else {
                        ret = regmap_write(priv->regmap, TIM_PSC, wfhw->psc);
                        if (ret)
                                goto out;

                        ret = regmap_write(priv->regmap, TIM_ARR, wfhw->arr);
                        if (ret)
                                goto out;

                        ret = regmap_set_bits(priv->regmap, TIM_CR1, TIM_CR1_ARPE);
                        if (ret)
                                goto out;

                }

                /* set polarity */
                mask = TIM_CCER_CCxP(ch + 1) | TIM_CCER_CCxNP(ch + 1);
                ret = regmap_update_bits(priv->regmap, TIM_CCER, mask, wfhw->ccer);
                if (ret)
                        goto out;

                ret = regmap_write(priv->regmap, TIM_CCRx(ch + 1), wfhw->ccr);
                if (ret)
                        goto out;

                /* Configure output mode */
                shift = (ch & 0x1) * CCMR_CHANNEL_SHIFT;
                ccmr = (TIM_CCMR_PE | TIM_CCMR_M1) << shift;
                mask = CCMR_CHANNEL_MASK << shift;

                if (ch < 2)
                        ret = regmap_update_bits(priv->regmap, TIM_CCMR1, mask, ccmr);
                else
                        ret = regmap_update_bits(priv->regmap, TIM_CCMR2, mask, ccmr);
                if (ret)
                        goto out;

                ret = regmap_set_bits(priv->regmap, TIM_BDTR, TIM_BDTR_MOE);
                if (ret)
                        goto out;

                if (!(ccer & TIM_CCER_CCxE(ch + 1))) {
                        mask = TIM_CCER_CCxE(ch + 1) | TIM_CCER_CCxNE(ch + 1);

                        ret = clk_enable(priv->clk);
                        if (ret)
                                goto out;

                        ccer = (ccer & ~mask) | (wfhw->ccer & mask);
                        regmap_write(priv->regmap, TIM_CCER, ccer);

                        /* Make sure that registers are updated */
                        regmap_set_bits(priv->regmap, TIM_EGR, TIM_EGR_UG);

                        /* Enable controller */
                        regmap_set_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN);
                }

        } else {
                /* disable channel */
                u32 mask, ccer;

                mask = TIM_CCER_CCxE(ch + 1);
                if (priv->have_complementary_output)
                        mask |= TIM_CCER_CCxNE(ch + 1);

                ret = regmap_read(priv->regmap, TIM_CCER, &ccer);
                if (ret)
                        goto out;

                if (ccer & mask) {
                        ccer = ccer & ~mask;

                        ret = regmap_write(priv->regmap, TIM_CCER, ccer);
                        if (ret)
                                goto out;

                        if (!(ccer & TIM_CCER_CCXE)) {
                                /* When all channels are disabled, we can disable the controller */
                                ret = regmap_clear_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN);
                                if (ret)
                                        goto out;
                        }

                        clk_disable(priv->clk);
                }
        }

out:
        clk_disable(priv->clk);

        return ret;
}

#define TIM_CCER_CC12P (TIM_CCER_CC1P | TIM_CCER_CC2P)
#define TIM_CCER_CC12E (TIM_CCER_CC1E | TIM_CCER_CC2E)
#define TIM_CCER_CC34P (TIM_CCER_CC3P | TIM_CCER_CC4P)
#define TIM_CCER_CC34E (TIM_CCER_CC3E | TIM_CCER_CC4E)

/*
 * Capture using PWM input mode:
 *                              ___          ___
 * TI[1, 2, 3 or 4]: ........._|   |________|
 *                             ^0  ^1       ^2
 *                              .   .        .
 *                              .   .        XXXXX
 *                              .   .   XXXXX     |
 *                              .  XXXXX     .    |
 *                            XXXXX .        .    |
 * COUNTER:        ______XXXXX  .   .        .    |_XXX
 *                 start^       .   .        .        ^stop
 *                      .       .   .        .
 *                      v       v   .        v
 *                                  v
 * CCR1/CCR3:       tx..........t0...........t2
 * CCR2/CCR4:       tx..............t1.........
 *
 * DMA burst transfer:          |            |
 *                              v            v
 * DMA buffer:                  { t0, tx }   { t2, t1 }
 * DMA done:                                 ^
 *
 * 0: IC1/3 snapchot on rising edge: counter value -> CCR1/CCR3
 *    + DMA transfer CCR[1/3] & CCR[2/4] values (t0, tx: doesn't care)
 * 1: IC2/4 snapchot on falling edge: counter value -> CCR2/CCR4
 * 2: IC1/3 snapchot on rising edge: counter value -> CCR1/CCR3
 *    + DMA transfer CCR[1/3] & CCR[2/4] values (t2, t1)
 *
 * DMA done, compute:
 * - Period     = t2 - t0
 * - Duty cycle = t1 - t0
 */
static int stm32_pwm_raw_capture(struct pwm_chip *chip, struct pwm_device *pwm,
                                 unsigned long tmo_ms, u32 *raw_prd,
                                 u32 *raw_dty)
{
        struct stm32_pwm *priv = to_stm32_pwm_dev(chip);
        struct device *parent = pwmchip_parent(chip)->parent;
        enum stm32_timers_dmas dma_id;
        u32 ccen, ccr;
        int ret;

        /* Ensure registers have been updated, enable counter and capture */
        regmap_set_bits(priv->regmap, TIM_EGR, TIM_EGR_UG);
        regmap_set_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN);

        /* Use cc1 or cc3 DMA resp for PWM input channels 1 & 2 or 3 & 4 */
        dma_id = pwm->hwpwm < 2 ? STM32_TIMERS_DMA_CH1 : STM32_TIMERS_DMA_CH3;
        ccen = pwm->hwpwm < 2 ? TIM_CCER_CC12E : TIM_CCER_CC34E;
        ccr = pwm->hwpwm < 2 ? TIM_CCR1 : TIM_CCR3;
        regmap_set_bits(priv->regmap, TIM_CCER, ccen);

        /*
         * Timer DMA burst mode. Request 2 registers, 2 bursts, to get both
         * CCR1 & CCR2 (or CCR3 & CCR4) on each capture event.
         * We'll get two capture snapchots: { CCR1, CCR2 }, { CCR1, CCR2 }
         * or { CCR3, CCR4 }, { CCR3, CCR4 }
         */
        ret = stm32_timers_dma_burst_read(parent, priv->capture, dma_id, ccr, 2,
                                          2, tmo_ms);
        if (ret)
                goto stop;

        /* Period: t2 - t0 (take care of counter overflow) */
        if (priv->capture[0] <= priv->capture[2])
                *raw_prd = priv->capture[2] - priv->capture[0];
        else
                *raw_prd = priv->max_arr - priv->capture[0] + priv->capture[2];

        /* Duty cycle capture requires at least two capture units */
        if (pwm->chip->npwm < 2)
                *raw_dty = 0;
        else if (priv->capture[0] <= priv->capture[3])
                *raw_dty = priv->capture[3] - priv->capture[0];
        else
                *raw_dty = priv->max_arr - priv->capture[0] + priv->capture[3];

        if (*raw_dty > *raw_prd) {
                /*
                 * Race beetween PWM input and DMA: it may happen
                 * falling edge triggers new capture on TI2/4 before DMA
                 * had a chance to read CCR2/4. It means capture[1]
                 * contains period + duty_cycle. So, subtract period.
                 */
                *raw_dty -= *raw_prd;
        }

stop:
        regmap_clear_bits(priv->regmap, TIM_CCER, ccen);
        regmap_clear_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN);

        return ret;
}

static int stm32_pwm_capture(struct pwm_chip *chip, struct pwm_device *pwm,
                             struct pwm_capture *result, unsigned long tmo_ms)
{
        struct stm32_pwm *priv = to_stm32_pwm_dev(chip);
        unsigned long long prd, div, dty;
        unsigned long rate;
        unsigned int psc = 0, icpsc, scale;
        u32 raw_prd = 0, raw_dty = 0;
        int ret = 0;

        mutex_lock(&priv->lock);

        if (active_channels(priv)) {
                ret = -EBUSY;
                goto unlock;
        }

        ret = clk_enable(priv->clk);
        if (ret) {
                dev_err(pwmchip_parent(chip), "failed to enable counter clock\n");
                goto unlock;
        }

        rate = clk_get_rate(priv->clk);
        if (!rate) {
                ret = -EINVAL;
                goto clk_dis;
        }

        /* prescaler: fit timeout window provided by upper layer */
        div = (unsigned long long)rate * (unsigned long long)tmo_ms;
        do_div(div, MSEC_PER_SEC);
        prd = div;
        while ((div > priv->max_arr) && (psc < MAX_TIM_PSC)) {
                psc++;
                div = prd;
                do_div(div, psc + 1);
        }
        regmap_write(priv->regmap, TIM_ARR, priv->max_arr);
        regmap_write(priv->regmap, TIM_PSC, psc);

        /* Reset input selector to its default input and disable slave mode */
        regmap_write(priv->regmap, TIM_TISEL, 0x0);
        regmap_write(priv->regmap, TIM_SMCR, 0x0);

        /* Map TI1 or TI2 PWM input to IC1 & IC2 (or TI3/4 to IC3 & IC4) */
        regmap_update_bits(priv->regmap,
                           pwm->hwpwm < 2 ? TIM_CCMR1 : TIM_CCMR2,
                           TIM_CCMR_CC1S | TIM_CCMR_CC2S, pwm->hwpwm & 0x1 ?
                           TIM_CCMR_CC1S_TI2 | TIM_CCMR_CC2S_TI2 :
                           TIM_CCMR_CC1S_TI1 | TIM_CCMR_CC2S_TI1);

        /* Capture period on IC1/3 rising edge, duty cycle on IC2/4 falling. */
        regmap_update_bits(priv->regmap, TIM_CCER, pwm->hwpwm < 2 ?
                           TIM_CCER_CC12P : TIM_CCER_CC34P, pwm->hwpwm < 2 ?
                           TIM_CCER_CC2P : TIM_CCER_CC4P);

        ret = stm32_pwm_raw_capture(chip, pwm, tmo_ms, &raw_prd, &raw_dty);
        if (ret)
                goto stop;

        /*
         * Got a capture. Try to improve accuracy at high rates:
         * - decrease counter clock prescaler, scale up to max rate.
         * - use input prescaler, capture once every /2 /4 or /8 edges.
         */
        if (raw_prd) {
                u32 max_arr = priv->max_arr - 0x1000; /* arbitrary margin */

                scale = max_arr / min(max_arr, raw_prd);
        } else {
                scale = priv->max_arr; /* below resolution, use max scale */
        }

        if (psc && scale > 1) {
                /* 2nd measure with new scale */
                psc /= scale;
                regmap_write(priv->regmap, TIM_PSC, psc);
                ret = stm32_pwm_raw_capture(chip, pwm, tmo_ms, &raw_prd,
                                            &raw_dty);
                if (ret)
                        goto stop;
        }

        /* Compute intermediate period not to exceed timeout at low rates */
        prd = (unsigned long long)raw_prd * (psc + 1) * NSEC_PER_SEC;
        do_div(prd, rate);

        for (icpsc = 0; icpsc < MAX_TIM_ICPSC ; icpsc++) {
                /* input prescaler: also keep arbitrary margin */
                if (raw_prd >= (priv->max_arr - 0x1000) >> (icpsc + 1))
                        break;
                if (prd >= (tmo_ms * NSEC_PER_MSEC) >> (icpsc + 2))
                        break;
        }

        if (!icpsc)
                goto done;

        /* Last chance to improve period accuracy, using input prescaler */
        regmap_update_bits(priv->regmap,
                           pwm->hwpwm < 2 ? TIM_CCMR1 : TIM_CCMR2,
                           TIM_CCMR_IC1PSC | TIM_CCMR_IC2PSC,
                           FIELD_PREP(TIM_CCMR_IC1PSC, icpsc) |
                           FIELD_PREP(TIM_CCMR_IC2PSC, icpsc));

        ret = stm32_pwm_raw_capture(chip, pwm, tmo_ms, &raw_prd, &raw_dty);
        if (ret)
                goto stop;

        if (raw_dty >= (raw_prd >> icpsc)) {
                /*
                 * We may fall here using input prescaler, when input
                 * capture starts on high side (before falling edge).
                 * Example with icpsc to capture on each 4 events:
                 *
                 *       start   1st capture                     2nd capture
                 *         v     v                               v
                 *         ___   _____   _____   _____   _____   ____
                 * TI1..4     |__|    |__|    |__|    |__|    |__|
                 *            v  v    .  .    .  .    .       v  v
                 * icpsc1/3:  .  0    .  1    .  2    .  3    .  0
                 * icpsc2/4:  0       1       2       3       0
                 *            v  v                            v  v
                 * CCR1/3  ......t0..............................t2
                 * CCR2/4  ..t1..............................t1'...
                 *               .                            .  .
                 * Capture0:     .<----------------------------->.
                 * Capture1:     .<-------------------------->.  .
                 *               .                            .  .
                 * Period:       .<------>                    .  .
                 * Low side:                                  .<>.
                 *
                 * Result:
                 * - Period = Capture0 / icpsc
                 * - Duty = Period - Low side = Period - (Capture0 - Capture1)
                 */
                raw_dty = (raw_prd >> icpsc) - (raw_prd - raw_dty);
        }

done:
        prd = (unsigned long long)raw_prd * (psc + 1) * NSEC_PER_SEC;
        result->period = DIV_ROUND_UP_ULL(prd, rate << icpsc);
        dty = (unsigned long long)raw_dty * (psc + 1) * NSEC_PER_SEC;
        result->duty_cycle = DIV_ROUND_UP_ULL(dty, rate);
stop:
        regmap_write(priv->regmap, TIM_CCER, 0);
        regmap_write(priv->regmap, pwm->hwpwm < 2 ? TIM_CCMR1 : TIM_CCMR2, 0);
        regmap_write(priv->regmap, TIM_PSC, 0);
clk_dis:
        clk_disable(priv->clk);
unlock:
        mutex_unlock(&priv->lock);

        return ret;
}

static const struct pwm_ops stm32pwm_ops = {
        .sizeof_wfhw = sizeof(struct stm32_pwm_waveform),
        .round_waveform_tohw = stm32_pwm_round_waveform_tohw,
        .round_waveform_fromhw = stm32_pwm_round_waveform_fromhw,
        .read_waveform = stm32_pwm_read_waveform,
        .write_waveform = stm32_pwm_write_waveform,

        .capture = IS_ENABLED(CONFIG_DMA_ENGINE) ? stm32_pwm_capture : NULL,
};

static int stm32_pwm_set_breakinput(struct stm32_pwm *priv,
                                    const struct stm32_breakinput *bi)
{
        u32 shift = TIM_BDTR_BKF_SHIFT(bi->index);
        u32 bke = TIM_BDTR_BKE(bi->index);
        u32 bkp = TIM_BDTR_BKP(bi->index);
        u32 bkf = TIM_BDTR_BKF(bi->index);
        u32 mask = bkf | bkp | bke;
        u32 bdtr;

        bdtr = (bi->filter & TIM_BDTR_BKF_MASK) << shift | bke;

        if (bi->level)
                bdtr |= bkp;

        regmap_update_bits(priv->regmap, TIM_BDTR, mask, bdtr);

        regmap_read(priv->regmap, TIM_BDTR, &bdtr);

        return (bdtr & bke) ? 0 : -EINVAL;
}

static int stm32_pwm_apply_breakinputs(struct stm32_pwm *priv)
{
        unsigned int i;
        int ret;

        for (i = 0; i < priv->num_breakinputs; i++) {
                ret = stm32_pwm_set_breakinput(priv, &priv->breakinputs[i]);
                if (ret < 0)
                        return ret;
        }

        return 0;
}

static int stm32_pwm_probe_breakinputs(struct stm32_pwm *priv,
                                       struct device_node *np)
{
        int nb, ret, array_size;
        unsigned int i;

        nb = of_property_count_elems_of_size(np, "st,breakinput",
                                             sizeof(struct stm32_breakinput));

        /*
         * Because "st,breakinput" parameter is optional do not make probe
         * failed if it doesn't exist.
         */
        if (nb <= 0)
                return 0;

        if (nb > MAX_BREAKINPUT)
                return -EINVAL;

        priv->num_breakinputs = nb;
        array_size = nb * sizeof(struct stm32_breakinput) / sizeof(u32);
        ret = of_property_read_u32_array(np, "st,breakinput",
                                         (u32 *)priv->breakinputs, array_size);
        if (ret)
                return ret;

        for (i = 0; i < priv->num_breakinputs; i++) {
                if (priv->breakinputs[i].index > 1 ||
                    priv->breakinputs[i].level > 1 ||
                    priv->breakinputs[i].filter > 15)
                        return -EINVAL;
        }

        return stm32_pwm_apply_breakinputs(priv);
}

static void stm32_pwm_detect_complementary(struct stm32_pwm *priv, struct stm32_timers *ddata)
{
        u32 ccer;

        if (ddata->ipidr) {
                u32 val;

                /* Simply read from HWCFGR the number of complementary outputs (MP25). */
                regmap_read(priv->regmap, TIM_HWCFGR1, &val);
                priv->have_complementary_output = !!FIELD_GET(TIM_HWCFGR1_NB_OF_DT, val);
                return;
        }

        /*
         * If complementary bit doesn't exist writing 1 will have no
         * effect so we can detect it.
         */
        regmap_set_bits(priv->regmap, TIM_CCER, TIM_CCER_CC1NE);
        regmap_read(priv->regmap, TIM_CCER, &ccer);
        regmap_clear_bits(priv->regmap, TIM_CCER, TIM_CCER_CC1NE);

        priv->have_complementary_output = (ccer != 0);
}

static unsigned int stm32_pwm_detect_channels(struct stm32_timers *ddata,
                                              unsigned int *num_enabled)
{
        struct regmap *regmap = ddata->regmap;
        u32 ccer, ccer_backup;

        regmap_read(regmap, TIM_CCER, &ccer_backup);
        *num_enabled = hweight32(ccer_backup & TIM_CCER_CCXE);

        if (ddata->ipidr) {
                u32 hwcfgr;
                unsigned int npwm;

                /* Deduce from HWCFGR the number of outputs (MP25). */
                regmap_read(regmap, TIM_HWCFGR1, &hwcfgr);

                /*
                 * Timers may have more capture/compare channels than the
                 * actual number of PWM channel outputs (e.g. TIM_CH[1..4]).
                 */
                npwm = FIELD_GET(TIM_HWCFGR1_NB_OF_CC, hwcfgr);

                return npwm < STM32_MAX_PWM_OUTPUT ? npwm : STM32_MAX_PWM_OUTPUT;
        }

        /*
         * If channels enable bits don't exist writing 1 will have no
         * effect so we can detect and count them.
         */
        regmap_set_bits(regmap, TIM_CCER, TIM_CCER_CCXE);
        regmap_read(regmap, TIM_CCER, &ccer);
        regmap_write(regmap, TIM_CCER, ccer_backup);

        return hweight32(ccer & TIM_CCER_CCXE);
}

static int stm32_pwm_probe(struct platform_device *pdev)
{
        struct device *dev = &pdev->dev;
        struct device_node *np = dev->of_node;
        struct stm32_timers *ddata = dev_get_drvdata(pdev->dev.parent);
        struct pwm_chip *chip;
        struct stm32_pwm *priv;
        unsigned int npwm, num_enabled;
        unsigned int i;
        int ret;

        npwm = stm32_pwm_detect_channels(ddata, &num_enabled);

        chip = devm_pwmchip_alloc(dev, npwm, sizeof(*priv));
        if (IS_ERR(chip))
                return PTR_ERR(chip);
        priv = to_stm32_pwm_dev(chip);

        mutex_init(&priv->lock);
        priv->regmap = ddata->regmap;
        priv->clk = ddata->clk;
        priv->max_arr = ddata->max_arr;

        if (!priv->regmap || !priv->clk)
                return dev_err_probe(dev, -EINVAL, "Failed to get %s\n",
                                     priv->regmap ? "clk" : "regmap");

        ret = stm32_pwm_probe_breakinputs(priv, np);
        if (ret)
                return dev_err_probe(dev, ret,
                                     "Failed to configure breakinputs\n");

        stm32_pwm_detect_complementary(priv, ddata);

        ret = devm_clk_rate_exclusive_get(dev, priv->clk);
        if (ret)
                return dev_err_probe(dev, ret, "Failed to lock clock\n");

        /*
         * With the clk running with not more than 1 GHz the calculations in
         * .apply() won't overflow.
         */
        if (clk_get_rate(priv->clk) > 1000000000)
                return dev_err_probe(dev, -EINVAL, "Clock freq too high (%lu)\n",
                                     clk_get_rate(priv->clk));

        chip->ops = &stm32pwm_ops;

        /* Initialize clock refcount to number of enabled PWM channels. */
        for (i = 0; i < num_enabled; i++) {
                ret = clk_enable(priv->clk);
                if (ret)
                        return ret;
        }

        ret = devm_pwmchip_add(dev, chip);
        if (ret < 0)
                return dev_err_probe(dev, ret,
                                     "Failed to register pwmchip\n");

        platform_set_drvdata(pdev, chip);

        return 0;
}

static int stm32_pwm_suspend(struct device *dev)
{
        struct pwm_chip *chip = dev_get_drvdata(dev);
        struct stm32_pwm *priv = to_stm32_pwm_dev(chip);
        unsigned int i;
        u32 ccer, mask;

        /* Look for active channels */
        ccer = active_channels(priv);

        for (i = 0; i < chip->npwm; i++) {
                mask = TIM_CCER_CCxE(i + 1);
                if (ccer & mask) {
                        dev_err(dev, "PWM %u still in use by consumer %s\n",
                                i, chip->pwms[i].label);
                        return -EBUSY;
                }
        }

        return pinctrl_pm_select_sleep_state(dev);
}

static int stm32_pwm_resume(struct device *dev)
{
        struct pwm_chip *chip = dev_get_drvdata(dev);
        struct stm32_pwm *priv = to_stm32_pwm_dev(chip);
        int ret;

        ret = pinctrl_pm_select_default_state(dev);
        if (ret)
                return ret;

        /* restore breakinput registers that may have been lost in low power */
        return stm32_pwm_apply_breakinputs(priv);
}

static DEFINE_SIMPLE_DEV_PM_OPS(stm32_pwm_pm_ops, stm32_pwm_suspend, stm32_pwm_resume);

static const struct of_device_id stm32_pwm_of_match[] = {
        { .compatible = "st,stm32-pwm", },
        { .compatible = "st,stm32mp25-pwm", },
        { /* end node */ },
};
MODULE_DEVICE_TABLE(of, stm32_pwm_of_match);

static struct platform_driver stm32_pwm_driver = {
        .probe  = stm32_pwm_probe,
        .driver = {
                .name = "stm32-pwm",
                .of_match_table = stm32_pwm_of_match,
                .pm = pm_ptr(&stm32_pwm_pm_ops),
        },
};
module_platform_driver(stm32_pwm_driver);

MODULE_ALIAS("platform:stm32-pwm");
MODULE_DESCRIPTION("STMicroelectronics STM32 PWM driver");
MODULE_LICENSE("GPL v2");