/*
 * Cypress APA trackpad with I2C interface
 *
 * Author: Dudley Du <dudl@cypress.com>
 * Further cleanup and restructuring by:
 *   Daniel Kurtz <djkurtz@chromium.org>
 *   Benson Leung <bleung@chromium.org>
 *
 * Copyright (C) 2011-2015 Cypress Semiconductor, Inc.
 * Copyright (C) 2011-2012 Google, Inc.
 *
 * This file is subject to the terms and conditions of the GNU General Public
 * License.  See the file COPYING in the main directory of this archive for
 * more details.
 */

#include <linux/delay.h>
#include <linux/i2c.h>
#include <linux/input.h>
#include <linux/input/mt.h>
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/unaligned.h>
#include "cyapa.h"


#define GEN3_MAX_FINGERS 5
#define GEN3_FINGER_NUM(x) (((x) >> 4) & 0x07)

#define BLK_HEAD_BYTES 32

/* Macro for register map group offset. */
#define PRODUCT_ID_SIZE  16
#define QUERY_DATA_SIZE  27
#define REG_PROTOCOL_GEN_QUERY_OFFSET  20

#define REG_OFFSET_DATA_BASE     0x0000
#define REG_OFFSET_COMMAND_BASE  0x0028
#define REG_OFFSET_QUERY_BASE    0x002a

#define CYAPA_OFFSET_SOFT_RESET  REG_OFFSET_COMMAND_BASE
#define OP_RECALIBRATION_MASK    0x80
#define OP_REPORT_BASELINE_MASK  0x40
#define REG_OFFSET_MAX_BASELINE  0x0026
#define REG_OFFSET_MIN_BASELINE  0x0027

#define REG_OFFSET_POWER_MODE (REG_OFFSET_COMMAND_BASE + 1)
#define SET_POWER_MODE_DELAY   10000  /* Unit: us */
#define SET_POWER_MODE_TRIES   5

#define GEN3_BL_CMD_CHECKSUM_SEED 0xff
#define GEN3_BL_CMD_INITIATE_BL   0x38
#define GEN3_BL_CMD_WRITE_BLOCK   0x39
#define GEN3_BL_CMD_VERIFY_BLOCK  0x3a
#define GEN3_BL_CMD_TERMINATE_BL  0x3b
#define GEN3_BL_CMD_LAUNCH_APP    0xa5

/*
 * CYAPA trackpad device states.
 * Used in register 0x00, bit1-0, DeviceStatus field.
 * Other values indicate device is in an abnormal state and must be reset.
 */
#define CYAPA_DEV_NORMAL  0x03
#define CYAPA_DEV_BUSY    0x01

#define CYAPA_FW_BLOCK_SIZE     64
#define CYAPA_FW_READ_SIZE      16
#define CYAPA_FW_HDR_START      0x0780
#define CYAPA_FW_HDR_BLOCK_COUNT  2
#define CYAPA_FW_HDR_BLOCK_START  (CYAPA_FW_HDR_START / CYAPA_FW_BLOCK_SIZE)
#define CYAPA_FW_HDR_SIZE         (CYAPA_FW_HDR_BLOCK_COUNT * \
                                        CYAPA_FW_BLOCK_SIZE)
#define CYAPA_FW_DATA_START     0x0800
#define CYAPA_FW_DATA_BLOCK_COUNT  480
#define CYAPA_FW_DATA_BLOCK_START  (CYAPA_FW_DATA_START / CYAPA_FW_BLOCK_SIZE)
#define CYAPA_FW_DATA_SIZE      (CYAPA_FW_DATA_BLOCK_COUNT * \
                                 CYAPA_FW_BLOCK_SIZE)
#define CYAPA_FW_SIZE           (CYAPA_FW_HDR_SIZE + CYAPA_FW_DATA_SIZE)
#define CYAPA_CMD_LEN           16

#define GEN3_BL_IDLE_FW_MAJ_VER_OFFSET 0x0b
#define GEN3_BL_IDLE_FW_MIN_VER_OFFSET (GEN3_BL_IDLE_FW_MAJ_VER_OFFSET + 1)


struct cyapa_touch {
        /*
         * high bits or x/y position value
         * bit 7 - 4: high 4 bits of x position value
         * bit 3 - 0: high 4 bits of y position value
         */
        u8 xy_hi;
        u8 x_lo;  /* low 8 bits of x position value. */
        u8 y_lo;  /* low 8 bits of y position value. */
        u8 pressure;
        /* id range is 1 - 15.  It is incremented with every new touch. */
        u8 id;
} __packed;

struct cyapa_reg_data {
        /*
         * bit 0 - 1: device status
         * bit 3 - 2: power mode
         * bit 6 - 4: reserved
         * bit 7: interrupt valid bit
         */
        u8 device_status;
        /*
         * bit 7 - 4: number of fingers currently touching pad
         * bit 3: valid data check bit
         * bit 2: middle mechanism button state if exists
         * bit 1: right mechanism button state if exists
         * bit 0: left mechanism button state if exists
         */
        u8 finger_btn;
        /* CYAPA reports up to 5 touches per packet. */
        struct cyapa_touch touches[5];
} __packed;

struct gen3_write_block_cmd {
        u8 checksum_seed;  /* Always be 0xff */
        u8 cmd_code;       /* command code: 0x39 */
        u8 key[8];         /* 8-byte security key */
        __be16 block_num;
        u8 block_data[CYAPA_FW_BLOCK_SIZE];
        u8 block_checksum;  /* Calculated using bytes 12 - 75 */
        u8 cmd_checksum;    /* Calculated using bytes 0-76 */
} __packed;

static const u8 security_key[] = {
                0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07 };
static const u8 bl_activate[] = { 0x00, 0xff, 0x38, 0x00, 0x01, 0x02, 0x03,
                0x04, 0x05, 0x06, 0x07 };
static const u8 bl_deactivate[] = { 0x00, 0xff, 0x3b, 0x00, 0x01, 0x02, 0x03,
                0x04, 0x05, 0x06, 0x07 };
static const u8 bl_exit[] = { 0x00, 0xff, 0xa5, 0x00, 0x01, 0x02, 0x03, 0x04,
                0x05, 0x06, 0x07 };


 /* for byte read/write command */
#define CMD_RESET 0
#define CMD_POWER_MODE 1
#define CMD_DEV_STATUS 2
#define CMD_REPORT_MAX_BASELINE 3
#define CMD_REPORT_MIN_BASELINE 4
#define SMBUS_BYTE_CMD(cmd) (((cmd) & 0x3f) << 1)
#define CYAPA_SMBUS_RESET         SMBUS_BYTE_CMD(CMD_RESET)
#define CYAPA_SMBUS_POWER_MODE    SMBUS_BYTE_CMD(CMD_POWER_MODE)
#define CYAPA_SMBUS_DEV_STATUS    SMBUS_BYTE_CMD(CMD_DEV_STATUS)
#define CYAPA_SMBUS_MAX_BASELINE  SMBUS_BYTE_CMD(CMD_REPORT_MAX_BASELINE)
#define CYAPA_SMBUS_MIN_BASELINE  SMBUS_BYTE_CMD(CMD_REPORT_MIN_BASELINE)

 /* for group registers read/write command */
#define REG_GROUP_DATA  0
#define REG_GROUP_CMD   2
#define REG_GROUP_QUERY 3
#define SMBUS_GROUP_CMD(grp) (0x80 | (((grp) & 0x07) << 3))
#define CYAPA_SMBUS_GROUP_DATA  SMBUS_GROUP_CMD(REG_GROUP_DATA)
#define CYAPA_SMBUS_GROUP_CMD   SMBUS_GROUP_CMD(REG_GROUP_CMD)
#define CYAPA_SMBUS_GROUP_QUERY SMBUS_GROUP_CMD(REG_GROUP_QUERY)

 /* for register block read/write command */
#define CMD_BL_STATUS           0
#define CMD_BL_HEAD             1
#define CMD_BL_CMD              2
#define CMD_BL_DATA             3
#define CMD_BL_ALL              4
#define CMD_BLK_PRODUCT_ID      5
#define CMD_BLK_HEAD            6
#define SMBUS_BLOCK_CMD(cmd) (0xc0 | (((cmd) & 0x1f) << 1))

/* register block read/write command in bootloader mode */
#define CYAPA_SMBUS_BL_STATUS SMBUS_BLOCK_CMD(CMD_BL_STATUS)
#define CYAPA_SMBUS_BL_HEAD   SMBUS_BLOCK_CMD(CMD_BL_HEAD)
#define CYAPA_SMBUS_BL_CMD    SMBUS_BLOCK_CMD(CMD_BL_CMD)
#define CYAPA_SMBUS_BL_DATA   SMBUS_BLOCK_CMD(CMD_BL_DATA)
#define CYAPA_SMBUS_BL_ALL    SMBUS_BLOCK_CMD(CMD_BL_ALL)

/* register block read/write command in operational mode */
#define CYAPA_SMBUS_BLK_PRODUCT_ID SMBUS_BLOCK_CMD(CMD_BLK_PRODUCT_ID)
#define CYAPA_SMBUS_BLK_HEAD       SMBUS_BLOCK_CMD(CMD_BLK_HEAD)

struct cyapa_cmd_len {
        u8 cmd;
        u8 len;
};

/* maps generic CYAPA_CMD_* code to the I2C equivalent */
static const struct cyapa_cmd_len cyapa_i2c_cmds[] = {
        { CYAPA_OFFSET_SOFT_RESET, 1 },         /* CYAPA_CMD_SOFT_RESET */
        { REG_OFFSET_COMMAND_BASE + 1, 1 },     /* CYAPA_CMD_POWER_MODE */
        { REG_OFFSET_DATA_BASE, 1 },            /* CYAPA_CMD_DEV_STATUS */
        { REG_OFFSET_DATA_BASE, sizeof(struct cyapa_reg_data) },
                                                /* CYAPA_CMD_GROUP_DATA */
        { REG_OFFSET_COMMAND_BASE, 0 },         /* CYAPA_CMD_GROUP_CMD */
        { REG_OFFSET_QUERY_BASE, QUERY_DATA_SIZE }, /* CYAPA_CMD_GROUP_QUERY */
        { BL_HEAD_OFFSET, 3 },                  /* CYAPA_CMD_BL_STATUS */
        { BL_HEAD_OFFSET, 16 },                 /* CYAPA_CMD_BL_HEAD */
        { BL_HEAD_OFFSET, 16 },                 /* CYAPA_CMD_BL_CMD */
        { BL_DATA_OFFSET, 16 },                 /* CYAPA_CMD_BL_DATA */
        { BL_HEAD_OFFSET, 32 },                 /* CYAPA_CMD_BL_ALL */
        { REG_OFFSET_QUERY_BASE, PRODUCT_ID_SIZE },
                                                /* CYAPA_CMD_BLK_PRODUCT_ID */
        { REG_OFFSET_DATA_BASE, 32 },           /* CYAPA_CMD_BLK_HEAD */
        { REG_OFFSET_MAX_BASELINE, 1 },         /* CYAPA_CMD_MAX_BASELINE */
        { REG_OFFSET_MIN_BASELINE, 1 },         /* CYAPA_CMD_MIN_BASELINE */
};

static const struct cyapa_cmd_len cyapa_smbus_cmds[] = {
        { CYAPA_SMBUS_RESET, 1 },               /* CYAPA_CMD_SOFT_RESET */
        { CYAPA_SMBUS_POWER_MODE, 1 },          /* CYAPA_CMD_POWER_MODE */
        { CYAPA_SMBUS_DEV_STATUS, 1 },          /* CYAPA_CMD_DEV_STATUS */
        { CYAPA_SMBUS_GROUP_DATA, sizeof(struct cyapa_reg_data) },
                                                /* CYAPA_CMD_GROUP_DATA */
        { CYAPA_SMBUS_GROUP_CMD, 2 },           /* CYAPA_CMD_GROUP_CMD */
        { CYAPA_SMBUS_GROUP_QUERY, QUERY_DATA_SIZE },
                                                /* CYAPA_CMD_GROUP_QUERY */
        { CYAPA_SMBUS_BL_STATUS, 3 },           /* CYAPA_CMD_BL_STATUS */
        { CYAPA_SMBUS_BL_HEAD, 16 },            /* CYAPA_CMD_BL_HEAD */
        { CYAPA_SMBUS_BL_CMD, 16 },             /* CYAPA_CMD_BL_CMD */
        { CYAPA_SMBUS_BL_DATA, 16 },            /* CYAPA_CMD_BL_DATA */
        { CYAPA_SMBUS_BL_ALL, 32 },             /* CYAPA_CMD_BL_ALL */
        { CYAPA_SMBUS_BLK_PRODUCT_ID, PRODUCT_ID_SIZE },
                                                /* CYAPA_CMD_BLK_PRODUCT_ID */
        { CYAPA_SMBUS_BLK_HEAD, 16 },           /* CYAPA_CMD_BLK_HEAD */
        { CYAPA_SMBUS_MAX_BASELINE, 1 },        /* CYAPA_CMD_MAX_BASELINE */
        { CYAPA_SMBUS_MIN_BASELINE, 1 },        /* CYAPA_CMD_MIN_BASELINE */
};

static int cyapa_gen3_try_poll_handler(struct cyapa *cyapa);

/*
 * cyapa_smbus_read_block - perform smbus block read command
 * @cyapa  - private data structure of the driver
 * @cmd    - the properly encoded smbus command
 * @len    - expected length of smbus command result
 * @values - buffer to store smbus command result
 *
 * Returns negative errno, else the number of bytes written.
 *
 * Note:
 * In trackpad device, the memory block allocated for I2C register map
 * is 256 bytes, so the max read block for I2C bus is 256 bytes.
 */
ssize_t cyapa_smbus_read_block(struct cyapa *cyapa, u8 cmd, size_t len,
                                      u8 *values)
{
        ssize_t ret;
        u8 index;
        u8 smbus_cmd;
        u8 *buf;
        struct i2c_client *client = cyapa->client;

        if (!(SMBUS_BYTE_BLOCK_CMD_MASK & cmd))
                return -EINVAL;

        if (SMBUS_GROUP_BLOCK_CMD_MASK & cmd) {
                /* read specific block registers command. */
                smbus_cmd = SMBUS_ENCODE_RW(cmd, SMBUS_READ);
                ret = i2c_smbus_read_block_data(client, smbus_cmd, values);
                goto out;
        }

        ret = 0;
        for (index = 0; index * I2C_SMBUS_BLOCK_MAX < len; index++) {
                smbus_cmd = SMBUS_ENCODE_IDX(cmd, index);
                smbus_cmd = SMBUS_ENCODE_RW(smbus_cmd, SMBUS_READ);
                buf = values + I2C_SMBUS_BLOCK_MAX * index;
                ret = i2c_smbus_read_block_data(client, smbus_cmd, buf);
                if (ret < 0)
                        goto out;
        }

out:
        return ret > 0 ? len : ret;
}

static s32 cyapa_read_byte(struct cyapa *cyapa, u8 cmd_idx)
{
        u8 cmd;

        if (cyapa->smbus) {
                cmd = cyapa_smbus_cmds[cmd_idx].cmd;
                cmd = SMBUS_ENCODE_RW(cmd, SMBUS_READ);
        } else {
                cmd = cyapa_i2c_cmds[cmd_idx].cmd;
        }
        return i2c_smbus_read_byte_data(cyapa->client, cmd);
}

static s32 cyapa_write_byte(struct cyapa *cyapa, u8 cmd_idx, u8 value)
{
        u8 cmd;

        if (cyapa->smbus) {
                cmd = cyapa_smbus_cmds[cmd_idx].cmd;
                cmd = SMBUS_ENCODE_RW(cmd, SMBUS_WRITE);
        } else {
                cmd = cyapa_i2c_cmds[cmd_idx].cmd;
        }
        return i2c_smbus_write_byte_data(cyapa->client, cmd, value);
}

ssize_t cyapa_i2c_reg_read_block(struct cyapa *cyapa, u8 reg, size_t len,
                                        u8 *values)
{
        return i2c_smbus_read_i2c_block_data(cyapa->client, reg, len, values);
}

static ssize_t cyapa_i2c_reg_write_block(struct cyapa *cyapa, u8 reg,
                                         size_t len, const u8 *values)
{
        return i2c_smbus_write_i2c_block_data(cyapa->client, reg, len, values);
}

ssize_t cyapa_read_block(struct cyapa *cyapa, u8 cmd_idx, u8 *values)
{
        u8 cmd;
        size_t len;

        if (cyapa->smbus) {
                cmd = cyapa_smbus_cmds[cmd_idx].cmd;
                len = cyapa_smbus_cmds[cmd_idx].len;
                return cyapa_smbus_read_block(cyapa, cmd, len, values);
        }
        cmd = cyapa_i2c_cmds[cmd_idx].cmd;
        len = cyapa_i2c_cmds[cmd_idx].len;
        return cyapa_i2c_reg_read_block(cyapa, cmd, len, values);
}

/*
 * Determine the Gen3 trackpad device's current operating state.
 *
 */
static int cyapa_gen3_state_parse(struct cyapa *cyapa, u8 *reg_data, int len)
{
        cyapa->state = CYAPA_STATE_NO_DEVICE;

        /* Parse based on Gen3 characteristic registers and bits */
        if (reg_data[REG_BL_FILE] == BL_FILE &&
                reg_data[REG_BL_ERROR] == BL_ERROR_NO_ERR_IDLE &&
                (reg_data[REG_BL_STATUS] ==
                        (BL_STATUS_RUNNING | BL_STATUS_CSUM_VALID) ||
                        reg_data[REG_BL_STATUS] == BL_STATUS_RUNNING)) {
                /*
                 * Normal state after power on or reset,
                 * REG_BL_STATUS == 0x11, firmware image checksum is valid.
                 * REG_BL_STATUS == 0x10, firmware image checksum is invalid.
                 */
                cyapa->gen = CYAPA_GEN3;
                cyapa->state = CYAPA_STATE_BL_IDLE;
        } else if (reg_data[REG_BL_FILE] == BL_FILE &&
                (reg_data[REG_BL_STATUS] & BL_STATUS_RUNNING) ==
                        BL_STATUS_RUNNING) {
                cyapa->gen = CYAPA_GEN3;
                if (reg_data[REG_BL_STATUS] & BL_STATUS_BUSY) {
                        cyapa->state = CYAPA_STATE_BL_BUSY;
                } else {
                        if ((reg_data[REG_BL_ERROR] & BL_ERROR_BOOTLOADING) ==
                                        BL_ERROR_BOOTLOADING)
                                cyapa->state = CYAPA_STATE_BL_ACTIVE;
                        else
                                cyapa->state = CYAPA_STATE_BL_IDLE;
                }
        } else if ((reg_data[REG_OP_STATUS] & OP_STATUS_SRC) &&
                        (reg_data[REG_OP_DATA1] & OP_DATA_VALID)) {
                /*
                 * Normal state when running in operational mode,
                 * may also not in full power state or
                 * busying in command process.
                 */
                if (GEN3_FINGER_NUM(reg_data[REG_OP_DATA1]) <=
                                GEN3_MAX_FINGERS) {
                        /* Finger number data is valid. */
                        cyapa->gen = CYAPA_GEN3;
                        cyapa->state = CYAPA_STATE_OP;
                }
        } else if (reg_data[REG_OP_STATUS] == 0x0C &&
                        reg_data[REG_OP_DATA1] == 0x08) {
                /* Op state when first two registers overwritten with 0x00 */
                cyapa->gen = CYAPA_GEN3;
                cyapa->state = CYAPA_STATE_OP;
        } else if (reg_data[REG_BL_STATUS] &
                        (BL_STATUS_RUNNING | BL_STATUS_BUSY)) {
                cyapa->gen = CYAPA_GEN3;
                cyapa->state = CYAPA_STATE_BL_BUSY;
        }

        if (cyapa->gen == CYAPA_GEN3 && (cyapa->state == CYAPA_STATE_OP ||
                cyapa->state == CYAPA_STATE_BL_IDLE ||
                cyapa->state == CYAPA_STATE_BL_ACTIVE ||
                cyapa->state == CYAPA_STATE_BL_BUSY))
                return 0;

        return -EAGAIN;
}

/*
 * Enter bootloader by soft resetting the device.
 *
 * If device is already in the bootloader, the function just returns.
 * Otherwise, reset the device; after reset, device enters bootloader idle
 * state immediately.
 *
 * Returns:
 *   0        on success
 *   -EAGAIN  device was reset, but is not now in bootloader idle state
 *   < 0      if the device never responds within the timeout
 */
static int cyapa_gen3_bl_enter(struct cyapa *cyapa)
{
        int error;
        int waiting_time;

        error = cyapa_poll_state(cyapa, 500);
        if (error)
                return error;
        if (cyapa->state == CYAPA_STATE_BL_IDLE) {
                /* Already in BL_IDLE. Skipping reset. */
                return 0;
        }

        if (cyapa->state != CYAPA_STATE_OP)
                return -EAGAIN;

        cyapa->operational = false;
        cyapa->state = CYAPA_STATE_NO_DEVICE;
        error = cyapa_write_byte(cyapa, CYAPA_CMD_SOFT_RESET, 0x01);
        if (error)
                return -EIO;

        usleep_range(25000, 50000);
        waiting_time = 2000;  /* For some shipset, max waiting time is 1~2s. */
        do {
                error = cyapa_poll_state(cyapa, 500);
                if (error) {
                        if (error == -ETIMEDOUT) {
                                waiting_time -= 500;
                                continue;
                        }
                        return error;
                }

                if ((cyapa->state == CYAPA_STATE_BL_IDLE) &&
                        !(cyapa->status[REG_BL_STATUS] & BL_STATUS_WATCHDOG))
                        break;

                msleep(100);
                waiting_time -= 100;
        } while (waiting_time > 0);

        if ((cyapa->state != CYAPA_STATE_BL_IDLE) ||
                (cyapa->status[REG_BL_STATUS] & BL_STATUS_WATCHDOG))
                return -EAGAIN;

        return 0;
}

static int cyapa_gen3_bl_activate(struct cyapa *cyapa)
{
        int error;

        error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_activate),
                                        bl_activate);
        if (error)
                return error;

        /* Wait for bootloader to activate; takes between 2 and 12 seconds */
        msleep(2000);
        error = cyapa_poll_state(cyapa, 11000);
        if (error)
                return error;
        if (cyapa->state != CYAPA_STATE_BL_ACTIVE)
                return -EAGAIN;

        return 0;
}

static int cyapa_gen3_bl_deactivate(struct cyapa *cyapa)
{
        int error;

        error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_deactivate),
                                        bl_deactivate);
        if (error)
                return error;

        /* Wait for bootloader to switch to idle state; should take < 100ms */
        msleep(100);
        error = cyapa_poll_state(cyapa, 500);
        if (error)
                return error;
        if (cyapa->state != CYAPA_STATE_BL_IDLE)
                return -EAGAIN;
        return 0;
}

/*
 * Exit bootloader
 *
 * Send bl_exit command, then wait 50 - 100 ms to let device transition to
 * operational mode.  If this is the first time the device's firmware is
 * running, it can take up to 2 seconds to calibrate its sensors.  So, poll
 * the device's new state for up to 2 seconds.
 *
 * Returns:
 *   -EIO    failure while reading from device
 *   -EAGAIN device is stuck in bootloader, b/c it has invalid firmware
 *   0       device is supported and in operational mode
 */
static int cyapa_gen3_bl_exit(struct cyapa *cyapa)
{
        int error;

        error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_exit), bl_exit);
        if (error)
                return error;

        /*
         * Wait for bootloader to exit, and operation mode to start.
         * Normally, this takes at least 50 ms.
         */
        msleep(50);
        /*
         * In addition, when a device boots for the first time after being
         * updated to new firmware, it must first calibrate its sensors, which
         * can take up to an additional 2 seconds. If the device power is
         * running low, this may take even longer.
         */
        error = cyapa_poll_state(cyapa, 4000);
        if (error < 0)
                return error;
        if (cyapa->state != CYAPA_STATE_OP)
                return -EAGAIN;

        return 0;
}

static u16 cyapa_gen3_csum(const u8 *buf, size_t count)
{
        int i;
        u16 csum = 0;

        for (i = 0; i < count; i++)
                csum += buf[i];

        return csum;
}

/*
 * Verify the integrity of a CYAPA firmware image file.
 *
 * The firmware image file is 30848 bytes, composed of 482 64-byte blocks.
 *
 * The first 2 blocks are the firmware header.
 * The next 480 blocks are the firmware image.
 *
 * The first two bytes of the header hold the header checksum, computed by
 * summing the other 126 bytes of the header.
 * The last two bytes of the header hold the firmware image checksum, computed
 * by summing the 30720 bytes of the image modulo 0xffff.
 *
 * Both checksums are stored little-endian.
 */
static int cyapa_gen3_check_fw(struct cyapa *cyapa, const struct firmware *fw)
{
        struct device *dev = &cyapa->client->dev;
        u16 csum;
        u16 csum_expected;

        /* Firmware must match exact 30848 bytes = 482 64-byte blocks. */
        if (fw->size != CYAPA_FW_SIZE) {
                dev_err(dev, "invalid firmware size = %zu, expected %u.\n",
                        fw->size, CYAPA_FW_SIZE);
                return -EINVAL;
        }

        /* Verify header block */
        csum_expected = (fw->data[0] << 8) | fw->data[1];
        csum = cyapa_gen3_csum(&fw->data[2], CYAPA_FW_HDR_SIZE - 2);
        if (csum != csum_expected) {
                dev_err(dev, "%s %04x, expected: %04x\n",
                        "invalid firmware header checksum = ",
                        csum, csum_expected);
                return -EINVAL;
        }

        /* Verify firmware image */
        csum_expected = (fw->data[CYAPA_FW_HDR_SIZE - 2] << 8) |
                         fw->data[CYAPA_FW_HDR_SIZE - 1];
        csum = cyapa_gen3_csum(&fw->data[CYAPA_FW_HDR_SIZE],
                        CYAPA_FW_DATA_SIZE);
        if (csum != csum_expected) {
                dev_err(dev, "%s %04x, expected: %04x\n",
                        "invalid firmware header checksum = ",
                        csum, csum_expected);
                return -EINVAL;
        }
        return 0;
}

/*
 * Write a |len| byte long buffer |buf| to the device, by chopping it up into a
 * sequence of smaller |CYAPA_CMD_LEN|-length write commands.
 *
 * The data bytes for a write command are prepended with the 1-byte offset
 * of the data relative to the start of |buf|.
 */
static int cyapa_gen3_write_buffer(struct cyapa *cyapa,
                const u8 *buf, size_t len)
{
        int error;
        size_t i;
        unsigned char cmd[CYAPA_CMD_LEN + 1];
        size_t cmd_len;

        for (i = 0; i < len; i += CYAPA_CMD_LEN) {
                const u8 *payload = &buf[i];

                cmd_len = (len - i >= CYAPA_CMD_LEN) ? CYAPA_CMD_LEN : len - i;
                cmd[0] = i;
                memcpy(&cmd[1], payload, cmd_len);

                error = cyapa_i2c_reg_write_block(cyapa, 0, cmd_len + 1, cmd);
                if (error)
                        return error;
        }
        return 0;
}

/*
 * A firmware block write command writes 64 bytes of data to a single flash
 * page in the device.  The 78-byte block write command has the format:
 *   <0xff> <CMD> <Key> <Start> <Data> <Data-Checksum> <CMD Checksum>
 *
 *  <0xff>  - every command starts with 0xff
 *  <CMD>   - the write command value is 0x39
 *  <Key>   - write commands include an 8-byte key: { 00 01 02 03 04 05 06 07 }
 *  <Block> - Memory Block number (address / 64) (16-bit, big-endian)
 *  <Data>  - 64 bytes of firmware image data
 *  <Data Checksum> - sum of 64 <Data> bytes, modulo 0xff
 *  <CMD Checksum> - sum of 77 bytes, from 0xff to <Data Checksum>
 *
 * Each write command is split into 5 i2c write transactions of up to 16 bytes.
 * Each transaction starts with an i2c register offset: (00, 10, 20, 30, 40).
 */
static int cyapa_gen3_write_fw_block(struct cyapa *cyapa,
                u16 block, const u8 *data)
{
        int ret;
        struct gen3_write_block_cmd write_block_cmd;
        u8 status[BL_STATUS_SIZE];
        int tries;
        u8 bl_status, bl_error;

        /* Set write command and security key bytes. */
        write_block_cmd.checksum_seed = GEN3_BL_CMD_CHECKSUM_SEED;
        write_block_cmd.cmd_code = GEN3_BL_CMD_WRITE_BLOCK;
        memcpy(write_block_cmd.key, security_key, sizeof(security_key));
        put_unaligned_be16(block, &write_block_cmd.block_num);
        memcpy(write_block_cmd.block_data, data, CYAPA_FW_BLOCK_SIZE);
        write_block_cmd.block_checksum = cyapa_gen3_csum(
                        write_block_cmd.block_data, CYAPA_FW_BLOCK_SIZE);
        write_block_cmd.cmd_checksum = cyapa_gen3_csum((u8 *)&write_block_cmd,
                        sizeof(write_block_cmd) - 1);

        ret = cyapa_gen3_write_buffer(cyapa, (u8 *)&write_block_cmd,
                        sizeof(write_block_cmd));
        if (ret)
                return ret;

        /* Wait for write to finish */
        tries = 11;  /* Programming for one block can take about 100ms. */
        do {
                usleep_range(10000, 20000);

                /* Check block write command result status. */
                ret = cyapa_i2c_reg_read_block(cyapa, BL_HEAD_OFFSET,
                                               BL_STATUS_SIZE, status);
                if (ret != BL_STATUS_SIZE)
                        return (ret < 0) ? ret : -EIO;
        } while ((status[REG_BL_STATUS] & BL_STATUS_BUSY) && --tries);

        /* Ignore WATCHDOG bit and reserved bits. */
        bl_status = status[REG_BL_STATUS] & ~BL_STATUS_REV_MASK;
        bl_error = status[REG_BL_ERROR] & ~BL_ERROR_RESERVED;

        if (bl_status & BL_STATUS_BUSY)
                ret = -ETIMEDOUT;
        else if (bl_status != BL_STATUS_RUNNING ||
                bl_error != BL_ERROR_BOOTLOADING)
                ret = -EIO;
        else
                ret = 0;

        return ret;
}

static int cyapa_gen3_write_blocks(struct cyapa *cyapa,
                size_t start_block, size_t block_count,
                const u8 *image_data)
{
        int error;
        int i;

        for (i = 0; i < block_count; i++) {
                size_t block = start_block + i;
                size_t addr = i * CYAPA_FW_BLOCK_SIZE;
                const u8 *data = &image_data[addr];

                error = cyapa_gen3_write_fw_block(cyapa, block, data);
                if (error)
                        return error;
        }
        return 0;
}

static int cyapa_gen3_do_fw_update(struct cyapa *cyapa,
                const struct firmware *fw)
{
        struct device *dev = &cyapa->client->dev;
        int error;

        /* First write data, starting at byte 128 of fw->data */
        error = cyapa_gen3_write_blocks(cyapa,
                CYAPA_FW_DATA_BLOCK_START, CYAPA_FW_DATA_BLOCK_COUNT,
                &fw->data[CYAPA_FW_HDR_BLOCK_COUNT * CYAPA_FW_BLOCK_SIZE]);
        if (error) {
                dev_err(dev, "FW update aborted, write image: %d\n", error);
                return error;
        }

        /* Then write checksum */
        error = cyapa_gen3_write_blocks(cyapa,
                CYAPA_FW_HDR_BLOCK_START, CYAPA_FW_HDR_BLOCK_COUNT,
                &fw->data[0]);
        if (error) {
                dev_err(dev, "FW update aborted, write checksum: %d\n", error);
                return error;
        }

        return 0;
}

static ssize_t cyapa_gen3_do_calibrate(struct device *dev,
                                     struct device_attribute *attr,
                                     const char *buf, size_t count)
{
        struct cyapa *cyapa = dev_get_drvdata(dev);
        unsigned long timeout;
        int ret;

        ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS);
        if (ret < 0) {
                dev_err(dev, "Error reading dev status: %d\n", ret);
                goto out;
        }
        if ((ret & CYAPA_DEV_NORMAL) != CYAPA_DEV_NORMAL) {
                dev_warn(dev, "Trackpad device is busy, device state: 0x%02x\n",
                         ret);
                ret = -EAGAIN;
                goto out;
        }

        ret = cyapa_write_byte(cyapa, CYAPA_CMD_SOFT_RESET,
                               OP_RECALIBRATION_MASK);
        if (ret < 0) {
                dev_err(dev, "Failed to send calibrate command: %d\n",
                        ret);
                goto out;
        }

        /* max recalibration timeout 2s. */
        timeout = jiffies + 2 * HZ;
        do {
                /*
                 * For this recalibration, the max time will not exceed 2s.
                 * The average time is approximately 500 - 700 ms, and we
                 * will check the status every 100 - 200ms.
                 */
                msleep(100);
                ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS);
                if (ret < 0) {
                        dev_err(dev, "Error reading dev status: %d\n", ret);
                        goto out;
                }
                if ((ret & CYAPA_DEV_NORMAL) == CYAPA_DEV_NORMAL) {
                        dev_dbg(dev, "Calibration successful.\n");
                        goto out;
                }
        } while (time_is_after_jiffies(timeout));

        dev_err(dev, "Failed to calibrate. Timeout.\n");
        ret = -ETIMEDOUT;

out:
        return ret < 0 ? ret : count;
}

static ssize_t cyapa_gen3_show_baseline(struct device *dev,
                                   struct device_attribute *attr, char *buf)
{
        struct cyapa *cyapa = dev_get_drvdata(dev);
        int max_baseline, min_baseline;
        int tries;
        int ret;

        ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS);
        if (ret < 0) {
                dev_err(dev, "Error reading dev status. err = %d\n", ret);
                goto out;
        }
        if ((ret & CYAPA_DEV_NORMAL) != CYAPA_DEV_NORMAL) {
                dev_warn(dev, "Trackpad device is busy. device state = 0x%x\n",
                         ret);
                ret = -EAGAIN;
                goto out;
        }

        ret = cyapa_write_byte(cyapa, CYAPA_CMD_SOFT_RESET,
                               OP_REPORT_BASELINE_MASK);
        if (ret < 0) {
                dev_err(dev, "Failed to send report baseline command. %d\n",
                        ret);
                goto out;
        }

        tries = 3;  /* Try for 30 to 60 ms */
        do {
                usleep_range(10000, 20000);

                ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS);
                if (ret < 0) {
                        dev_err(dev, "Error reading dev status. err = %d\n",
                                ret);
                        goto out;
                }
                if ((ret & CYAPA_DEV_NORMAL) == CYAPA_DEV_NORMAL)
                        break;
        } while (--tries);

        if (tries == 0) {
                dev_err(dev, "Device timed out going to Normal state.\n");
                ret = -ETIMEDOUT;
                goto out;
        }

        ret = cyapa_read_byte(cyapa, CYAPA_CMD_MAX_BASELINE);
        if (ret < 0) {
                dev_err(dev, "Failed to read max baseline. err = %d\n", ret);
                goto out;
        }
        max_baseline = ret;

        ret = cyapa_read_byte(cyapa, CYAPA_CMD_MIN_BASELINE);
        if (ret < 0) {
                dev_err(dev, "Failed to read min baseline. err = %d\n", ret);
                goto out;
        }
        min_baseline = ret;

        dev_dbg(dev, "Baseline report successful. Max: %d Min: %d\n",
                max_baseline, min_baseline);
        ret = sysfs_emit(buf, "%d %d\n", max_baseline, min_baseline);

out:
        return ret;
}

/*
 * cyapa_get_wait_time_for_pwr_cmd
 *
 * Compute the amount of time we need to wait after updating the touchpad
 * power mode. The touchpad needs to consume the incoming power mode set
 * command at the current clock rate.
 */

static u16 cyapa_get_wait_time_for_pwr_cmd(u8 pwr_mode)
{
        switch (pwr_mode) {
        case PWR_MODE_FULL_ACTIVE: return 20;
        case PWR_MODE_BTN_ONLY: return 20;
        case PWR_MODE_OFF: return 20;
        default: return cyapa_pwr_cmd_to_sleep_time(pwr_mode) + 50;
        }
}

/*
 * Set device power mode
 *
 * Write to the field to configure power state. Power states include :
 *   Full : Max scans and report rate.
 *   Idle : Report rate set by user specified time.
 *   ButtonOnly : No scans for fingers. When the button is triggered,
 *     a slave interrupt is asserted to notify host to wake up.
 *   Off : Only awake for i2c commands from host. No function for button
 *     or touch sensors.
 *
 * The power_mode command should conform to the following :
 *   Full : 0x3f
 *   Idle : Configurable from 20 to 1000ms. See note below for
 *     cyapa_sleep_time_to_pwr_cmd and cyapa_pwr_cmd_to_sleep_time
 *   ButtonOnly : 0x01
 *   Off : 0x00
 *
 * Device power mode can only be set when device is in operational mode.
 */
static int cyapa_gen3_set_power_mode(struct cyapa *cyapa, u8 power_mode,
                u16 always_unused, enum cyapa_pm_stage pm_stage)
{
        struct input_dev *input = cyapa->input;
        u8 power;
        int tries;
        int sleep_time;
        int interval;
        int ret;

        if (cyapa->state != CYAPA_STATE_OP)
                return 0;

        tries = SET_POWER_MODE_TRIES;
        while (tries--) {
                ret = cyapa_read_byte(cyapa, CYAPA_CMD_POWER_MODE);
                if (ret >= 0)
                        break;
                usleep_range(SET_POWER_MODE_DELAY, 2 * SET_POWER_MODE_DELAY);
        }
        if (ret < 0)
                return ret;

        /*
         * Return early if the power mode to set is the same as the current
         * one.
         */
        if ((ret & PWR_MODE_MASK) == power_mode)
                return 0;

        sleep_time = (int)cyapa_get_wait_time_for_pwr_cmd(ret & PWR_MODE_MASK);
        power = ret;
        power &= ~PWR_MODE_MASK;
        power |= power_mode & PWR_MODE_MASK;
        tries = SET_POWER_MODE_TRIES;
        while (tries--) {
                ret = cyapa_write_byte(cyapa, CYAPA_CMD_POWER_MODE, power);
                if (!ret)
                        break;
                usleep_range(SET_POWER_MODE_DELAY, 2 * SET_POWER_MODE_DELAY);
        }

        /*
         * Wait for the newly set power command to go in at the previous
         * clock speed (scanrate) used by the touchpad firmware. Not
         * doing so before issuing the next command may result in errors
         * depending on the command's content.
         */
        if (cyapa->operational &&
            input && input_device_enabled(input) &&
            (pm_stage == CYAPA_PM_RUNTIME_SUSPEND ||
             pm_stage == CYAPA_PM_RUNTIME_RESUME)) {
                /* Try to polling in 120Hz, read may fail, just ignore it. */
                interval = 1000 / 120;
                while (sleep_time > 0) {
                        if (sleep_time > interval)
                                msleep(interval);
                        else
                                msleep(sleep_time);
                        sleep_time -= interval;
                        cyapa_gen3_try_poll_handler(cyapa);
                }
        } else {
                msleep(sleep_time);
        }

        return ret;
}

static int cyapa_gen3_set_proximity(struct cyapa *cyapa, bool enable)
{
        return -EOPNOTSUPP;
}

static int cyapa_gen3_get_query_data(struct cyapa *cyapa)
{
        u8 query_data[QUERY_DATA_SIZE];
        int ret;

        if (cyapa->state != CYAPA_STATE_OP)
                return -EBUSY;

        ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_QUERY, query_data);
        if (ret != QUERY_DATA_SIZE)
                return (ret < 0) ? ret : -EIO;

        memcpy(&cyapa->product_id[0], &query_data[0], 5);
        cyapa->product_id[5] = '-';
        memcpy(&cyapa->product_id[6], &query_data[5], 6);
        cyapa->product_id[12] = '-';
        memcpy(&cyapa->product_id[13], &query_data[11], 2);
        cyapa->product_id[15] = '\0';

        cyapa->fw_maj_ver = query_data[15];
        cyapa->fw_min_ver = query_data[16];

        cyapa->btn_capability = query_data[19] & CAPABILITY_BTN_MASK;

        cyapa->gen = query_data[20] & 0x0f;

        cyapa->max_abs_x = ((query_data[21] & 0xf0) << 4) | query_data[22];
        cyapa->max_abs_y = ((query_data[21] & 0x0f) << 8) | query_data[23];

        cyapa->physical_size_x =
                ((query_data[24] & 0xf0) << 4) | query_data[25];
        cyapa->physical_size_y =
                ((query_data[24] & 0x0f) << 8) | query_data[26];

        cyapa->max_z = 255;

        return 0;
}

static int cyapa_gen3_bl_query_data(struct cyapa *cyapa)
{
        u8 bl_data[CYAPA_CMD_LEN];
        int ret;

        ret = cyapa_i2c_reg_read_block(cyapa, 0, CYAPA_CMD_LEN, bl_data);
        if (ret != CYAPA_CMD_LEN)
                return (ret < 0) ? ret : -EIO;

        /*
         * This value will be updated again when entered application mode.
         * If TP failed to enter application mode, this fw version values
         * can be used as a reference.
         * This firmware version valid when fw image checksum is valid.
         */
        if (bl_data[REG_BL_STATUS] ==
                        (BL_STATUS_RUNNING | BL_STATUS_CSUM_VALID)) {
                cyapa->fw_maj_ver = bl_data[GEN3_BL_IDLE_FW_MAJ_VER_OFFSET];
                cyapa->fw_min_ver = bl_data[GEN3_BL_IDLE_FW_MIN_VER_OFFSET];
        }

        return 0;
}

/*
 * Check if device is operational.
 *
 * An operational device is responding, has exited bootloader, and has
 * firmware supported by this driver.
 *
 * Returns:
 *   -EBUSY  no device or in bootloader
 *   -EIO    failure while reading from device
 *   -EAGAIN device is still in bootloader
 *           if ->state = CYAPA_STATE_BL_IDLE, device has invalid firmware
 *   -EINVAL device is in operational mode, but not supported by this driver
 *   0       device is supported
 */
static int cyapa_gen3_do_operational_check(struct cyapa *cyapa)
{
        struct device *dev = &cyapa->client->dev;
        int error;

        switch (cyapa->state) {
        case CYAPA_STATE_BL_ACTIVE:
                error = cyapa_gen3_bl_deactivate(cyapa);
                if (error) {
                        dev_err(dev, "failed to bl_deactivate: %d\n", error);
                        return error;
                }

                fallthrough;
        case CYAPA_STATE_BL_IDLE:
                /* Try to get firmware version in bootloader mode. */
                cyapa_gen3_bl_query_data(cyapa);

                error = cyapa_gen3_bl_exit(cyapa);
                if (error) {
                        dev_err(dev, "failed to bl_exit: %d\n", error);
                        return error;
                }

                fallthrough;
        case CYAPA_STATE_OP:
                /*
                 * Reading query data before going back to the full mode
                 * may cause problems, so we set the power mode first here.
                 */
                error = cyapa_gen3_set_power_mode(cyapa,
                                PWR_MODE_FULL_ACTIVE, 0, CYAPA_PM_ACTIVE);
                if (error)
                        dev_err(dev, "%s: set full power mode failed: %d\n",
                                __func__, error);
                error = cyapa_gen3_get_query_data(cyapa);
                if (error < 0)
                        return error;

                /* Only support firmware protocol gen3 */
                if (cyapa->gen != CYAPA_GEN3) {
                        dev_err(dev, "unsupported protocol version (%d)",
                                cyapa->gen);
                        return -EINVAL;
                }

                /* Only support product ID starting with CYTRA */
                if (memcmp(cyapa->product_id, product_id,
                                strlen(product_id)) != 0) {
                        dev_err(dev, "unsupported product ID (%s)\n",
                                cyapa->product_id);
                        return -EINVAL;
                }

                return 0;

        default:
                return -EIO;
        }
        return 0;
}

/*
 * Return false, do not continue process
 * Return true, continue process.
 */
static bool cyapa_gen3_irq_cmd_handler(struct cyapa *cyapa)
{
        /* Not gen3 irq command response, skip for continue. */
        if (cyapa->gen != CYAPA_GEN3)
                return true;

        if (cyapa->operational)
                return true;

        /*
         * Driver in detecting or other interface function processing,
         * so, stop cyapa_gen3_irq_handler to continue process to
         * avoid unwanted to error detecting and processing.
         *
         * And also, avoid the periodically asserted interrupts to be processed
         * as touch inputs when gen3 failed to launch into application mode,
         * which will cause gen3 stays in bootloader mode.
         */
        return false;
}

static int cyapa_gen3_event_process(struct cyapa *cyapa,
                                    struct cyapa_reg_data *data)
{
        struct input_dev *input = cyapa->input;
        int num_fingers;
        int i;

        num_fingers = (data->finger_btn >> 4) & 0x0f;
        for (i = 0; i < num_fingers; i++) {
                const struct cyapa_touch *touch = &data->touches[i];
                /* Note: touch->id range is 1 to 15; slots are 0 to 14. */
                int slot = touch->id - 1;

                input_mt_slot(input, slot);
                input_mt_report_slot_state(input, MT_TOOL_FINGER, true);
                input_report_abs(input, ABS_MT_POSITION_X,
                                 ((touch->xy_hi & 0xf0) << 4) | touch->x_lo);
                input_report_abs(input, ABS_MT_POSITION_Y,
                                 ((touch->xy_hi & 0x0f) << 8) | touch->y_lo);
                input_report_abs(input, ABS_MT_PRESSURE, touch->pressure);
        }

        input_mt_sync_frame(input);

        if (cyapa->btn_capability & CAPABILITY_LEFT_BTN_MASK)
                input_report_key(input, BTN_LEFT,
                                 !!(data->finger_btn & OP_DATA_LEFT_BTN));
        if (cyapa->btn_capability & CAPABILITY_MIDDLE_BTN_MASK)
                input_report_key(input, BTN_MIDDLE,
                                 !!(data->finger_btn & OP_DATA_MIDDLE_BTN));
        if (cyapa->btn_capability & CAPABILITY_RIGHT_BTN_MASK)
                input_report_key(input, BTN_RIGHT,
                                 !!(data->finger_btn & OP_DATA_RIGHT_BTN));
        input_sync(input);

        return 0;
}

static int cyapa_gen3_irq_handler(struct cyapa *cyapa)
{
        struct device *dev = &cyapa->client->dev;
        struct cyapa_reg_data data;
        int ret;

        ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_DATA, (u8 *)&data);
        if (ret != sizeof(data)) {
                dev_err(dev, "failed to read report data, (%d)\n", ret);
                return -EINVAL;
        }

        if ((data.device_status & OP_STATUS_SRC) != OP_STATUS_SRC ||
            (data.device_status & OP_STATUS_DEV) != CYAPA_DEV_NORMAL ||
            (data.finger_btn & OP_DATA_VALID) != OP_DATA_VALID) {
                dev_err(dev, "invalid device state bytes: %02x %02x\n",
                        data.device_status, data.finger_btn);
                return -EINVAL;
        }

        return cyapa_gen3_event_process(cyapa, &data);
}

/*
 * This function will be called in the cyapa_gen3_set_power_mode function,
 * and it's known that it may failed in some situation after the set power
 * mode command was sent. So this function is aimed to avoid the knwon
 * and unwanted output I2C and data parse error messages.
 */
static int cyapa_gen3_try_poll_handler(struct cyapa *cyapa)
{
        struct cyapa_reg_data data;
        int ret;

        ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_DATA, (u8 *)&data);
        if (ret != sizeof(data))
                return -EINVAL;

        if ((data.device_status & OP_STATUS_SRC) != OP_STATUS_SRC ||
            (data.device_status & OP_STATUS_DEV) != CYAPA_DEV_NORMAL ||
            (data.finger_btn & OP_DATA_VALID) != OP_DATA_VALID)
                return -EINVAL;

        return cyapa_gen3_event_process(cyapa, &data);

}

static int cyapa_gen3_initialize(struct cyapa *cyapa) { return 0; }
static int cyapa_gen3_bl_initiate(struct cyapa *cyapa,
                const struct firmware *fw) { return 0; }
static int cyapa_gen3_empty_output_data(struct cyapa *cyapa,
                u8 *buf, int *len, cb_sort func) { return 0; }

const struct cyapa_dev_ops cyapa_gen3_ops = {
        .check_fw = cyapa_gen3_check_fw,
        .bl_enter = cyapa_gen3_bl_enter,
        .bl_activate = cyapa_gen3_bl_activate,
        .update_fw = cyapa_gen3_do_fw_update,
        .bl_deactivate = cyapa_gen3_bl_deactivate,
        .bl_initiate = cyapa_gen3_bl_initiate,

        .show_baseline = cyapa_gen3_show_baseline,
        .calibrate_store = cyapa_gen3_do_calibrate,

        .initialize = cyapa_gen3_initialize,

        .state_parse = cyapa_gen3_state_parse,
        .operational_check = cyapa_gen3_do_operational_check,

        .irq_handler = cyapa_gen3_irq_handler,
        .irq_cmd_handler = cyapa_gen3_irq_cmd_handler,
        .sort_empty_output_data = cyapa_gen3_empty_output_data,
        .set_power_mode = cyapa_gen3_set_power_mode,

        .set_proximity = cyapa_gen3_set_proximity,
};