/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * max8998.h - Voltage regulator driver for the Maxim 8998
 *
 *  Copyright (C) 2009-2010 Samsung Electronics
 *  Kyungmin Park <kyungmin.park@samsung.com>
 *  Marek Szyprowski <m.szyprowski@samsung.com>
 */

#ifndef __LINUX_MFD_MAX8998_H
#define __LINUX_MFD_MAX8998_H

#include <linux/regulator/machine.h>

/* MAX 8998 regulator ids */
enum {
        MAX8998_LDO2 = 2,
        MAX8998_LDO3,
        MAX8998_LDO4,
        MAX8998_LDO5,
        MAX8998_LDO6,
        MAX8998_LDO7,
        MAX8998_LDO8,
        MAX8998_LDO9,
        MAX8998_LDO10,
        MAX8998_LDO11,
        MAX8998_LDO12,
        MAX8998_LDO13,
        MAX8998_LDO14,
        MAX8998_LDO15,
        MAX8998_LDO16,
        MAX8998_LDO17,
        MAX8998_BUCK1,
        MAX8998_BUCK2,
        MAX8998_BUCK3,
        MAX8998_BUCK4,
        MAX8998_EN32KHZ_AP,
        MAX8998_EN32KHZ_CP,
        MAX8998_ENVICHG,
        MAX8998_ESAFEOUT1,
        MAX8998_ESAFEOUT2,
        MAX8998_CHARGER,
};

/**
 * max8998_regulator_data - regulator data
 * @id: regulator id
 * @initdata: regulator init data (contraints, supplies, ...)
 * @reg_node: DT node of regulator (unused on non-DT platforms)
 */
struct max8998_regulator_data {
        int                             id;
        struct regulator_init_data      *initdata;
        struct device_node              *reg_node;
};

/**
 * struct max8998_board - packages regulator init data
 * @regulators: array of defined regulators
 * @num_regulators: number of regulators used
 * @irq_base: base IRQ number for max8998, required for IRQs
 * @ono: power onoff IRQ number for max8998
 * @buck_voltage_lock: Do NOT change the values of the following six
 *   registers set by buck?_voltage?. The voltage of BUCK1/2 cannot
 *   be other than the preset values.
 * @buck1_voltage: BUCK1 DVS mode 1 voltage registers
 * @buck2_voltage: BUCK2 DVS mode 2 voltage registers
 * @buck1_default_idx: Default for BUCK1 gpio pin 1, 2
 * @buck2_default_idx: Default for BUCK2 gpio pin.
 * @wakeup: Allow to wake up from suspend
 * @rtc_delay: LP3974 RTC chip bug that requires delay after a register
 * write before reading it.
 * @eoc: End of Charge Level in percent: 10% ~ 45% by 5% step
 *   If it equals 0, leave it unchanged.
 *   Otherwise, it is a invalid value.
 * @restart: Restart Level in mV: 100, 150, 200, and -1 for disable.
 *   If it equals 0, leave it unchanged.
 *   Otherwise, it is a invalid value.
 * @timeout: Full Timeout in hours: 5, 6, 7, and -1 for disable.
 *   If it equals 0, leave it unchanged.
 *   Otherwise, leave it unchanged.
 */
struct max8998_platform_data {
        struct max8998_regulator_data   *regulators;
        int                             num_regulators;
        unsigned int                    irq_base;
        int                             ono;
        bool                            buck_voltage_lock;
        int                             buck1_voltage[4];
        int                             buck2_voltage[2];
        int                             buck1_default_idx;
        int                             buck2_default_idx;
        bool                            wakeup;
        bool                            rtc_delay;
        int                             eoc;
        int                             restart;
        int                             timeout;
};

#endif /*  __LINUX_MFD_MAX8998_H */