// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * Copyright (C) 2001,2002,2005 Broadcom Corporation
 * Copyright (C) 2004 by Ralf Baechle (ralf@linux-mips.org)
 */

/*
 * BCM1x80/1x55-specific PCI support
 *
 * This module provides the glue between Linux's PCI subsystem
 * and the hardware.  We basically provide glue for accessing
 * configuration space, and set up the translation for I/O
 * space accesses.
 *
 * To access configuration space, we use ioremap.  In the 32-bit
 * kernel, this consumes either 4 or 8 page table pages, and 16MB of
 * kernel mapped memory.  Hopefully neither of these should be a huge
 * problem.
 *
 * XXX: AT THIS TIME, ONLY the NATIVE PCI-X INTERFACE IS SUPPORTED.
 */
#include <linux/types.h>
#include <linux/pci.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/console.h>
#include <linux/tty.h>
#include <linux/vt.h>

#include <asm/sibyte/bcm1480_regs.h>
#include <asm/sibyte/bcm1480_scd.h>
#include <asm/sibyte/board.h>
#include <asm/io.h>

/*
 * Macros for calculating offsets into config space given a device
 * structure or dev/fun/reg
 */
#define CFGOFFSET(bus, devfn, where) (((bus)<<16)+((devfn)<<8)+(where))
#define CFGADDR(bus, devfn, where)   CFGOFFSET((bus)->number, (devfn), where)

static void *cfg_space;

#define PCI_BUS_ENABLED 1
#define PCI_DEVICE_MODE 2

static int bcm1480_bus_status;

#define PCI_BRIDGE_DEVICE  0

/*
 * Read/write 32-bit values in config space.
 */
static inline u32 READCFG32(u32 addr)
{
        return *(u32 *)(cfg_space + (addr&~3));
}

static inline void WRITECFG32(u32 addr, u32 data)
{
        *(u32 *)(cfg_space + (addr & ~3)) = data;
}

int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
{
        if (pin == 0)
                return -1;

        return K_BCM1480_INT_PCI_INTA - 1 + pin;
}

/* Do platform specific device initialization at pci_enable_device() time */
int pcibios_plat_dev_init(struct pci_dev *dev)
{
        return 0;
}

/*
 * Some checks before doing config cycles:
 * In PCI Device Mode, hide everything on bus 0 except the LDT host
 * bridge.  Otherwise, access is controlled by bridge MasterEn bits.
 */
static int bcm1480_pci_can_access(struct pci_bus *bus, int devfn)
{
        u32 devno;

        if (!(bcm1480_bus_status & (PCI_BUS_ENABLED | PCI_DEVICE_MODE)))
                return 0;

        if (bus->number == 0) {
                devno = PCI_SLOT(devfn);
                if (bcm1480_bus_status & PCI_DEVICE_MODE)
                        return 0;
                else
                        return 1;
        } else
                return 1;
}

/*
 * Read/write access functions for various sizes of values
 * in config space.  Return all 1's for disallowed accesses
 * for a kludgy but adequate simulation of master aborts.
 */

static int bcm1480_pcibios_read(struct pci_bus *bus, unsigned int devfn,
                                int where, int size, u32 * val)
{
        u32 data = 0;

        if ((size == 2) && (where & 1))
                return PCIBIOS_BAD_REGISTER_NUMBER;
        else if ((size == 4) && (where & 3))
                return PCIBIOS_BAD_REGISTER_NUMBER;

        if (bcm1480_pci_can_access(bus, devfn))
                data = READCFG32(CFGADDR(bus, devfn, where));
        else
                data = 0xFFFFFFFF;

        if (size == 1)
                *val = (data >> ((where & 3) << 3)) & 0xff;
        else if (size == 2)
                *val = (data >> ((where & 3) << 3)) & 0xffff;
        else
                *val = data;

        return PCIBIOS_SUCCESSFUL;
}

static int bcm1480_pcibios_write(struct pci_bus *bus, unsigned int devfn,
                                int where, int size, u32 val)
{
        u32 cfgaddr = CFGADDR(bus, devfn, where);
        u32 data = 0;

        if ((size == 2) && (where & 1))
                return PCIBIOS_BAD_REGISTER_NUMBER;
        else if ((size == 4) && (where & 3))
                return PCIBIOS_BAD_REGISTER_NUMBER;

        if (!bcm1480_pci_can_access(bus, devfn))
                return PCIBIOS_BAD_REGISTER_NUMBER;

        data = READCFG32(cfgaddr);

        if (size == 1)
                data = (data & ~(0xff << ((where & 3) << 3))) |
                    (val << ((where & 3) << 3));
        else if (size == 2)
                data = (data & ~(0xffff << ((where & 3) << 3))) |
                    (val << ((where & 3) << 3));
        else
                data = val;

        WRITECFG32(cfgaddr, data);

        return PCIBIOS_SUCCESSFUL;
}

struct pci_ops bcm1480_pci_ops = {
        .read   = bcm1480_pcibios_read,
        .write  = bcm1480_pcibios_write,
};

static struct resource bcm1480_mem_resource = {
        .name   = "BCM1480 PCI MEM",
        .start  = A_BCM1480_PHYS_PCI_MEM_MATCH_BYTES,
        .end    = A_BCM1480_PHYS_PCI_MEM_MATCH_BYTES + 0xfffffffUL,
        .flags  = IORESOURCE_MEM,
};

static struct resource bcm1480_io_resource = {
        .name   = "BCM1480 PCI I/O",
        .start  = A_BCM1480_PHYS_PCI_IO_MATCH_BYTES,
        .end    = A_BCM1480_PHYS_PCI_IO_MATCH_BYTES + 0x1ffffffUL,
        .flags  = IORESOURCE_IO,
};

struct pci_controller bcm1480_controller = {
        .pci_ops        = &bcm1480_pci_ops,
        .mem_resource   = &bcm1480_mem_resource,
        .io_resource    = &bcm1480_io_resource,
        .io_offset      = A_BCM1480_PHYS_PCI_IO_MATCH_BYTES,
};


static int __init bcm1480_pcibios_init(void)
{
        uint32_t cmdreg;
        uint64_t reg;

        /* CFE will assign PCI resources */
        pci_set_flags(PCI_PROBE_ONLY);

        /* Avoid ISA compat ranges.  */
        PCIBIOS_MIN_IO = 0x00008000UL;
        PCIBIOS_MIN_MEM = 0x01000000UL;

        /* Set I/O resource limits. - unlimited for now to accommodate HT */
        ioport_resource.end = 0xffffffffUL;
        iomem_resource.end = 0xffffffffUL;

        cfg_space = ioremap(A_BCM1480_PHYS_PCI_CFG_MATCH_BITS, 16*1024*1024);

        /*
         * See if the PCI bus has been configured by the firmware.
         */
        reg = __raw_readq(IOADDR(A_SCD_SYSTEM_CFG));
        if (!(reg & M_BCM1480_SYS_PCI_HOST)) {
                bcm1480_bus_status |= PCI_DEVICE_MODE;
        } else {
                cmdreg = READCFG32(CFGOFFSET(0, PCI_DEVFN(PCI_BRIDGE_DEVICE, 0),
                                             PCI_COMMAND));
                if (!(cmdreg & PCI_COMMAND_MASTER)) {
                        printk
                            ("PCI: Skipping PCI probe.  Bus is not initialized.\n");
                        iounmap(cfg_space);
                        return 1; /* XXX */
                }
                bcm1480_bus_status |= PCI_BUS_ENABLED;
        }

        /* turn on ExpMemEn */
        cmdreg = READCFG32(CFGOFFSET(0, PCI_DEVFN(PCI_BRIDGE_DEVICE, 0), 0x40));
        WRITECFG32(CFGOFFSET(0, PCI_DEVFN(PCI_BRIDGE_DEVICE, 0), 0x40),
                        cmdreg | 0x10);
        cmdreg = READCFG32(CFGOFFSET(0, PCI_DEVFN(PCI_BRIDGE_DEVICE, 0), 0x40));

        /*
         * Establish mappings in KSEG2 (kernel virtual) to PCI I/O
         * space.  Use "match bytes" policy to make everything look
         * little-endian.  So, you need to also set
         * CONFIG_SWAP_IO_SPACE, but this is the combination that
         * works correctly with most of Linux's drivers.
         * XXX ehs: Should this happen in PCI Device mode?
         */

        bcm1480_controller.io_map_base = (unsigned long)
                ioremap(A_BCM1480_PHYS_PCI_IO_MATCH_BYTES, 65536);
        bcm1480_controller.io_map_base -= bcm1480_controller.io_offset;
        set_io_port_base(bcm1480_controller.io_map_base);

        register_pci_controller(&bcm1480_controller);

#ifdef CONFIG_VGA_CONSOLE
        console_lock();
        do_take_over_console(&vga_con, 0, MAX_NR_CONSOLES-1, 1);
        console_unlock();
#endif
        return 0;
}

arch_initcall(bcm1480_pcibios_init);