// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * Freescale Lite5200 board support
 *
 * Written by: Grant Likely <grant.likely@secretlab.ca>
 *
 * Copyright (C) Secret Lab Technologies Ltd. 2006. All rights reserved.
 * Copyright 2006 Freescale Semiconductor, Inc. All rights reserved.
 *
 * Description:
 */

#undef DEBUG

#include <linux/init.h>
#include <linux/pci.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/root_dev.h>
#include <linux/initrd.h>
#include <asm/time.h>
#include <asm/io.h>
#include <asm/machdep.h>
#include <asm/mpc52xx.h>

/* ************************************************************************
 *
 * Setup the architecture
 *
 */

/* mpc5200 device tree match tables */
static const struct of_device_id mpc5200_cdm_ids[] __initconst = {
        { .compatible = "fsl,mpc5200-cdm", },
        { .compatible = "mpc5200-cdm", },
        {}
};

static const struct of_device_id mpc5200_gpio_ids[] __initconst = {
        { .compatible = "fsl,mpc5200-gpio", },
        { .compatible = "mpc5200-gpio", },
        {}
};

/*
 * Fix clock configuration.
 *
 * Firmware is supposed to be responsible for this.  If you are creating a
 * new board port, do *NOT* duplicate this code.  Fix your boot firmware
 * to set it correctly in the first place
 */
static void __init
lite5200_fix_clock_config(void)
{
        struct device_node *np;
        struct mpc52xx_cdm  __iomem *cdm;
        /* Map zones */
        np = of_find_matching_node(NULL, mpc5200_cdm_ids);
        cdm = of_iomap(np, 0);
        of_node_put(np);
        if (!cdm) {
                printk(KERN_ERR "%s() failed; expect abnormal behaviour\n",
                       __func__);
                return;
        }

        /* Use internal 48 Mhz */
        out_8(&cdm->ext_48mhz_en, 0x00);
        out_8(&cdm->fd_enable, 0x01);
        if (in_be32(&cdm->rstcfg) & 0x40)       /* Assumes 33Mhz clock */
                out_be16(&cdm->fd_counters, 0x0001);
        else
                out_be16(&cdm->fd_counters, 0x5555);

        /* Unmap the regs */
        iounmap(cdm);
}

/*
 * Fix setting of port_config register.
 *
 * Firmware is supposed to be responsible for this.  If you are creating a
 * new board port, do *NOT* duplicate this code.  Fix your boot firmware
 * to set it correctly in the first place
 */
static void __init
lite5200_fix_port_config(void)
{
        struct device_node *np;
        struct mpc52xx_gpio __iomem *gpio;
        u32 port_config;

        np = of_find_matching_node(NULL, mpc5200_gpio_ids);
        gpio = of_iomap(np, 0);
        of_node_put(np);
        if (!gpio) {
                printk(KERN_ERR "%s() failed. expect abnormal behavior\n",
                       __func__);
                return;
        }

        /* Set port config */
        port_config = in_be32(&gpio->port_config);

        port_config &= ~0x00800000;     /* 48Mhz internal, pin is GPIO  */

        port_config &= ~0x00007000;     /* USB port : Differential mode */
        port_config |=  0x00001000;     /*            USB 1 only        */

        port_config &= ~0x03000000;     /* ATA CS is on csb_4/5         */
        port_config |=  0x01000000;

        pr_debug("port_config: old:%x new:%x\n",
                 in_be32(&gpio->port_config), port_config);
        out_be32(&gpio->port_config, port_config);

        /* Unmap zone */
        iounmap(gpio);
}

#ifdef CONFIG_PM
static void lite5200_suspend_prepare(void __iomem *mbar)
{
        u8 pin = 1;     /* GPIO_WKUP_1 (GPIO_PSC2_4) */
        u8 level = 0;   /* wakeup on low level */
        mpc52xx_set_wakeup_gpio(pin, level);

        /*
         * power down usb port
         * this needs to be called before of-ohci suspend code
         */

        /* set ports to "power switched" and "powered at the same time"
         * USB Rh descriptor A: NPS = 0, PSM = 0 */
        out_be32(mbar + 0x1048, in_be32(mbar + 0x1048) & ~0x300);
        /* USB Rh status: LPS = 1 - turn off power */
        out_be32(mbar + 0x1050, 0x00000001);
}

static void lite5200_resume_finish(void __iomem *mbar)
{
        /* USB Rh status: LPSC = 1 - turn on power */
        out_be32(mbar + 0x1050, 0x00010000);
}
#endif

static void __init lite5200_setup_arch(void)
{
        if (ppc_md.progress)
                ppc_md.progress("lite5200_setup_arch()", 0);

        /* Map important registers from the internal memory map */
        mpc52xx_map_common_devices();

        /* Some mpc5200 & mpc5200b related configuration */
        mpc5200_setup_xlb_arbiter();

        /* Fix things that firmware should have done. */
        lite5200_fix_clock_config();
        lite5200_fix_port_config();

#ifdef CONFIG_PM
        mpc52xx_suspend.board_suspend_prepare = lite5200_suspend_prepare;
        mpc52xx_suspend.board_resume_finish = lite5200_resume_finish;
        lite5200_pm_init();
#endif
}

static const char * const board[] __initconst = {
        "fsl,lite5200",
        "fsl,lite5200b",
        NULL,
};

define_machine(lite5200) {
        .name           = "lite5200",
        .compatibles    = board,
        .setup_arch     = lite5200_setup_arch,
        .discover_phbs  = mpc52xx_setup_pci,
        .init           = mpc52xx_declare_of_platform_devices,
        .init_IRQ       = mpc52xx_init_irq,
        .get_irq        = mpc52xx_get_irq,
        .restart        = mpc52xx_restart,
};