// SPDX-License-Identifier: GPL-2.0-only
/*
 * Broadcom Brahma-B15 CPU read-ahead cache management functions
 *
 * Copyright (C) 2015-2016 Broadcom
 */

#include <linux/cfi_types.h>
#include <linux/err.h>
#include <linux/spinlock.h>
#include <linux/io.h>
#include <linux/bitops.h>
#include <linux/of_address.h>
#include <linux/notifier.h>
#include <linux/cpu.h>
#include <linux/syscore_ops.h>
#include <linux/reboot.h>

#include <asm/cacheflush.h>
#include <asm/hardware/cache-b15-rac.h>

extern void v7_flush_kern_cache_all(void);

/* RAC register offsets, relative to the HIF_CPU_BIUCTRL register base */
#define RAC_CONFIG0_REG                 (0x78)
#define  RACENPREF_MASK                 (0x3)
#define  RACPREFINST_SHIFT              (0)
#define  RACENINST_SHIFT                (2)
#define  RACPREFDATA_SHIFT              (4)
#define  RACENDATA_SHIFT                (6)
#define  RAC_CPU_SHIFT                  (8)
#define  RACCFG_MASK                    (0xff)
#define RAC_CONFIG1_REG                 (0x7c)
/* Brahma-B15 is a quad-core only design */
#define B15_RAC_FLUSH_REG               (0x80)
/* Brahma-B53 is an octo-core design */
#define B53_RAC_FLUSH_REG               (0x84)
#define  FLUSH_RAC                      (1 << 0)

/* Bitmask to enable instruction and data prefetching with a 256-bytes stride */
#define RAC_DATA_INST_EN_MASK           (1 << RACPREFINST_SHIFT | \
                                         RACENPREF_MASK << RACENINST_SHIFT | \
                                         1 << RACPREFDATA_SHIFT | \
                                         RACENPREF_MASK << RACENDATA_SHIFT)

#define RAC_ENABLED                     0
/* Special state where we want to bypass the spinlock and call directly
 * into the v7 cache maintenance operations during suspend/resume
 */
#define RAC_SUSPENDED                   1

static void __iomem *b15_rac_base;
static DEFINE_SPINLOCK(rac_lock);

static u32 rac_config0_reg;
static u32 rac_flush_offset;

/* Initialization flag to avoid checking for b15_rac_base, and to prevent
 * multi-platform kernels from crashing here as well.
 */
static unsigned long b15_rac_flags;

static inline u32 __b15_rac_disable(void)
{
        u32 val = __raw_readl(b15_rac_base + RAC_CONFIG0_REG);
        __raw_writel(0, b15_rac_base + RAC_CONFIG0_REG);
        dmb();
        return val;
}

static inline void __b15_rac_flush(void)
{
        u32 reg;

        __raw_writel(FLUSH_RAC, b15_rac_base + rac_flush_offset);
        do {
                /* This dmb() is required to force the Bus Interface Unit
                 * to clean outstanding writes, and forces an idle cycle
                 * to be inserted.
                 */
                dmb();
                reg = __raw_readl(b15_rac_base + rac_flush_offset);
        } while (reg & FLUSH_RAC);
}

static inline u32 b15_rac_disable_and_flush(void)
{
        u32 reg;

        reg = __b15_rac_disable();
        __b15_rac_flush();
        return reg;
}

static inline void __b15_rac_enable(u32 val)
{
        __raw_writel(val, b15_rac_base + RAC_CONFIG0_REG);
        /* dsb() is required here to be consistent with __flush_icache_all() */
        dsb();
}

#define BUILD_RAC_CACHE_OP(name, bar)                           \
void b15_flush_##name(void)                                     \
{                                                               \
        unsigned int do_flush;                                  \
        u32 val = 0;                                            \
                                                                \
        if (test_bit(RAC_SUSPENDED, &b15_rac_flags)) {          \
                v7_flush_##name();                              \
                bar;                                            \
                return;                                         \
        }                                                       \
                                                                \
        spin_lock(&rac_lock);                                   \
        do_flush = test_bit(RAC_ENABLED, &b15_rac_flags);       \
        if (do_flush)                                           \
                val = b15_rac_disable_and_flush();              \
        v7_flush_##name();                                      \
        if (!do_flush)                                          \
                bar;                                            \
        else                                                    \
                __b15_rac_enable(val);                          \
        spin_unlock(&rac_lock);                                 \
}

#define nobarrier

/* The readahead cache present in the Brahma-B15 CPU is a special piece of
 * hardware after the integrated L2 cache of the B15 CPU complex whose purpose
 * is to prefetch instruction and/or data with a line size of either 64 bytes
 * or 256 bytes. The rationale is that the data-bus of the CPU interface is
 * optimized for 256-bytes transactions, and enabling the readahead cache
 * provides a significant performance boost we want it enabled (typically
 * twice the performance for a memcpy benchmark application).
 *
 * The readahead cache is transparent for Modified Virtual Addresses
 * cache maintenance operations: ICIMVAU, DCIMVAC, DCCMVAC, DCCMVAU and
 * DCCIMVAC.
 *
 * It is however not transparent for the following cache maintenance
 * operations: DCISW, DCCSW, DCCISW, ICIALLUIS and ICIALLU which is precisely
 * what we are patching here with our BUILD_RAC_CACHE_OP here.
 */
BUILD_RAC_CACHE_OP(kern_cache_all, nobarrier);

static void b15_rac_enable(void)
{
        unsigned int cpu;
        u32 enable = 0;

        for_each_possible_cpu(cpu)
                enable |= (RAC_DATA_INST_EN_MASK << (cpu * RAC_CPU_SHIFT));

        b15_rac_disable_and_flush();
        __b15_rac_enable(enable);
}

static int b15_rac_reboot_notifier(struct notifier_block *nb,
                                   unsigned long action,
                                   void *data)
{
        /* During kexec, we are not yet migrated on the boot CPU, so we need to
         * make sure we are SMP safe here. Once the RAC is disabled, flag it as
         * suspended such that the hotplug notifier returns early.
         */
        if (action == SYS_RESTART) {
                spin_lock(&rac_lock);
                b15_rac_disable_and_flush();
                clear_bit(RAC_ENABLED, &b15_rac_flags);
                set_bit(RAC_SUSPENDED, &b15_rac_flags);
                spin_unlock(&rac_lock);
        }

        return NOTIFY_DONE;
}

static struct notifier_block b15_rac_reboot_nb = {
        .notifier_call  = b15_rac_reboot_notifier,
};

/* The CPU hotplug case is the most interesting one, we basically need to make
 * sure that the RAC is disabled for the entire system prior to having a CPU
 * die, in particular prior to this dying CPU having exited the coherency
 * domain.
 *
 * Once this CPU is marked dead, we can safely re-enable the RAC for the
 * remaining CPUs in the system which are still online.
 *
 * Offlining a CPU is the problematic case, onlining a CPU is not much of an
 * issue since the CPU and its cache-level hierarchy will start filling with
 * the RAC disabled, so L1 and L2 only.
 *
 * In this function, we should NOT have to verify any unsafe setting/condition
 * b15_rac_base:
 *
 *   It is protected by the RAC_ENABLED flag which is cleared by default, and
 *   being cleared when initial procedure is done. b15_rac_base had been set at
 *   that time.
 *
 * RAC_ENABLED:
 *   There is a small timing windows, in b15_rac_init(), between
 *      cpuhp_setup_state_*()
 *      ...
 *      set RAC_ENABLED
 *   However, there is no hotplug activity based on the Linux booting procedure.
 *
 * Since we have to disable RAC for all cores, we keep RAC on as long as as
 * possible (disable it as late as possible) to gain the cache benefit.
 *
 * Thus, dying/dead states are chosen here
 *
 * We are choosing not do disable the RAC on a per-CPU basis, here, if we did
 * we would want to consider disabling it as early as possible to benefit the
 * other active CPUs.
 */

/* Running on the dying CPU */
static int b15_rac_dying_cpu(unsigned int cpu)
{
        /* During kexec/reboot, the RAC is disabled via the reboot notifier
         * return early here.
         */
        if (test_bit(RAC_SUSPENDED, &b15_rac_flags))
                return 0;

        spin_lock(&rac_lock);

        /* Indicate that we are starting a hotplug procedure */
        __clear_bit(RAC_ENABLED, &b15_rac_flags);

        /* Disable the readahead cache and save its value to a global */
        rac_config0_reg = b15_rac_disable_and_flush();

        spin_unlock(&rac_lock);

        return 0;
}

/* Running on a non-dying CPU */
static int b15_rac_dead_cpu(unsigned int cpu)
{
        /* During kexec/reboot, the RAC is disabled via the reboot notifier
         * return early here.
         */
        if (test_bit(RAC_SUSPENDED, &b15_rac_flags))
                return 0;

        spin_lock(&rac_lock);

        /* And enable it */
        __b15_rac_enable(rac_config0_reg);
        __set_bit(RAC_ENABLED, &b15_rac_flags);

        spin_unlock(&rac_lock);

        return 0;
}

static int b15_rac_suspend(void *data)
{
        /* Suspend the read-ahead cache oeprations, forcing our cache
         * implementation to fallback to the regular ARMv7 calls.
         *
         * We are guaranteed to be running on the boot CPU at this point and
         * with every other CPU quiesced, so setting RAC_SUSPENDED is not racy
         * here.
         */
        rac_config0_reg = b15_rac_disable_and_flush();
        set_bit(RAC_SUSPENDED, &b15_rac_flags);

        return 0;
}

static void b15_rac_resume(void *data)
{
        /* Coming out of a S3 suspend/resume cycle, the read-ahead cache
         * register RAC_CONFIG0_REG will be restored to its default value, make
         * sure we re-enable it and set the enable flag, we are also guaranteed
         * to run on the boot CPU, so not racy again.
         */
        __b15_rac_enable(rac_config0_reg);
        clear_bit(RAC_SUSPENDED, &b15_rac_flags);
}

static const struct syscore_ops b15_rac_syscore_ops = {
        .suspend        = b15_rac_suspend,
        .resume         = b15_rac_resume,
};

static struct syscore b15_rac_syscore = {
        .ops = &b15_rac_syscore_ops,
};

static int __init b15_rac_init(void)
{
        struct device_node *dn, *cpu_dn;
        int ret = 0, cpu;
        u32 reg, en_mask = 0;

        dn = of_find_compatible_node(NULL, NULL, "brcm,brcmstb-cpu-biu-ctrl");
        if (!dn)
                return -ENODEV;

        if (WARN(num_possible_cpus() > 4, "RAC only supports 4 CPUs\n"))
                goto out;

        b15_rac_base = of_iomap(dn, 0);
        if (!b15_rac_base) {
                pr_err("failed to remap BIU control base\n");
                ret = -ENOMEM;
                goto out;
        }

        cpu_dn = of_get_cpu_node(0, NULL);
        if (!cpu_dn) {
                ret = -ENODEV;
                goto out;
        }

        if (of_device_is_compatible(cpu_dn, "brcm,brahma-b15"))
                rac_flush_offset = B15_RAC_FLUSH_REG;
        else if (of_device_is_compatible(cpu_dn, "brcm,brahma-b53"))
                rac_flush_offset = B53_RAC_FLUSH_REG;
        else {
                pr_err("Unsupported CPU\n");
                of_node_put(cpu_dn);
                ret = -EINVAL;
                goto out;
        }
        of_node_put(cpu_dn);

        ret = register_reboot_notifier(&b15_rac_reboot_nb);
        if (ret) {
                pr_err("failed to register reboot notifier\n");
                iounmap(b15_rac_base);
                goto out;
        }

        if (IS_ENABLED(CONFIG_HOTPLUG_CPU)) {
                ret = cpuhp_setup_state_nocalls(CPUHP_AP_ARM_CACHE_B15_RAC_DEAD,
                                        "arm/cache-b15-rac:dead",
                                        NULL, b15_rac_dead_cpu);
                if (ret)
                        goto out_unmap;

                ret = cpuhp_setup_state_nocalls(CPUHP_AP_ARM_CACHE_B15_RAC_DYING,
                                        "arm/cache-b15-rac:dying",
                                        NULL, b15_rac_dying_cpu);
                if (ret)
                        goto out_cpu_dead;
        }

        if (IS_ENABLED(CONFIG_PM_SLEEP))
                register_syscore(&b15_rac_syscore);

        spin_lock(&rac_lock);
        reg = __raw_readl(b15_rac_base + RAC_CONFIG0_REG);
        for_each_possible_cpu(cpu)
                en_mask |= ((1 << RACPREFDATA_SHIFT) << (cpu * RAC_CPU_SHIFT));
        WARN(reg & en_mask, "Read-ahead cache not previously disabled\n");

        b15_rac_enable();
        set_bit(RAC_ENABLED, &b15_rac_flags);
        spin_unlock(&rac_lock);

        pr_info("%pOF: Broadcom Brahma-B15 readahead cache\n", dn);

        goto out;

out_cpu_dead:
        cpuhp_remove_state_nocalls(CPUHP_AP_ARM_CACHE_B15_RAC_DYING);
out_unmap:
        unregister_reboot_notifier(&b15_rac_reboot_nb);
        iounmap(b15_rac_base);
out:
        of_node_put(dn);
        return ret;
}
arch_initcall(b15_rac_init);