/*-
 * SPDX-License-Identifier: BSD-2-Clause
 *
 * Copyright (c) 2000-2001 Jonathan Chen All rights reserved.
 * Copyright (c) 2002-2004 M. Warner Losh <imp@FreeBSD.org>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 * SUCH DAMAGE.
 *
 */

/*-
 * Copyright (c) 1998, 1999 and 2000
 *      HAYAKAWA Koichi.  All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. All advertising materials mentioning features or use of this software
 *    must display the following acknowledgement:
 *      This product includes software developed by HAYAKAWA Koichi.
 * 4. The name of the author may not be used to endorse or promote products
 *    derived from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

/*
 * Driver for PCI to CardBus Bridge chips
 *
 * References:
 *  TI Datasheets:
 *   http://www-s.ti.com/cgi-bin/sc/generic2.cgi?family=PCI+CARDBUS+CONTROLLERS
 *
 * Written by Jonathan Chen <jon@freebsd.org>
 * The author would like to acknowledge:
 *  * HAYAKAWA Koichi: Author of the NetBSD code for the same thing
 *  * Warner Losh: Newbus/newcard guru and author of the pccard side of things
 *  * YAMAMOTO Shigeru: Author of another FreeBSD cardbus driver
 *  * David Cross: Author of the initial ugly hack for a specific cardbus card
 */

#include <sys/param.h>
#include <sys/bus.h>
#include <sys/condvar.h>
#include <sys/errno.h>
#include <sys/kernel.h>
#include <sys/module.h>
#include <sys/kthread.h>
#include <sys/lock.h>
#include <sys/malloc.h>
#include <sys/mutex.h>
#include <sys/proc.h>
#include <sys/rman.h>
#include <sys/sysctl.h>
#include <sys/systm.h>
#include <machine/bus.h>
#include <machine/resource.h>

#include <dev/pci/pcireg.h>
#include <dev/pci/pcivar.h>
#include <dev/pci/pcib_private.h>

#include <dev/pccard/pccardreg.h>
#include <dev/pccard/pccardvar.h>

#include <dev/exca/excareg.h>
#include <dev/exca/excavar.h>

#include <dev/pccbb/pccbbreg.h>
#include <dev/pccbb/pccbbvar.h>

#include "power_if.h"
#include "card_if.h"
#include "pcib_if.h"

#define DPRINTF(x) do { if (cbb_debug) printf x; } while (0)
#define DEVPRINTF(x) do { if (cbb_debug) device_printf x; } while (0)

#define PCI_MASK_CONFIG(DEV,REG,MASK,SIZE)                              \
        pci_write_config(DEV, REG, pci_read_config(DEV, REG, SIZE) MASK, SIZE)
#define PCI_MASK2_CONFIG(DEV,REG,MASK1,MASK2,SIZE)                      \
        pci_write_config(DEV, REG, (                                    \
                pci_read_config(DEV, REG, SIZE) MASK1) MASK2, SIZE)

#define CBB_CARD_PRESENT(s) ((s & CBB_STATE_CD) == 0)

#define CBB_START_MEM   0x88000000
#define CBB_START_32_IO 0x1000
#define CBB_START_16_IO 0x100

/* sysctl vars */
static SYSCTL_NODE(_hw, OID_AUTO, cbb, CTLFLAG_RD | CTLFLAG_MPSAFE, 0,
    "CBB parameters");

/* There's no way to say TUNEABLE_LONG to get the right types */
u_long cbb_start_mem = CBB_START_MEM;
SYSCTL_ULONG(_hw_cbb, OID_AUTO, start_memory, CTLFLAG_RWTUN,
    &cbb_start_mem, CBB_START_MEM,
    "Starting address for memory allocations");

u_long cbb_start_16_io = CBB_START_16_IO;
SYSCTL_ULONG(_hw_cbb, OID_AUTO, start_16_io, CTLFLAG_RWTUN,
    &cbb_start_16_io, CBB_START_16_IO,
    "Starting ioport for 16-bit cards");

u_long cbb_start_32_io = CBB_START_32_IO;
SYSCTL_ULONG(_hw_cbb, OID_AUTO, start_32_io, CTLFLAG_RWTUN,
    &cbb_start_32_io, CBB_START_32_IO,
    "Starting ioport for 32-bit cards");

int cbb_debug = 0;
SYSCTL_INT(_hw_cbb, OID_AUTO, debug, CTLFLAG_RWTUN, &cbb_debug, 0,
    "Verbose cardbus bridge debugging");

static void     cbb_insert(struct cbb_softc *sc);
static void     cbb_removal(struct cbb_softc *sc);
static uint32_t cbb_detect_voltage(device_t brdev);
static int      cbb_cardbus_reset_power(device_t brdev, device_t child, int on);
static int      cbb_cardbus_io_open(device_t brdev, int win, uint32_t start,
                    uint32_t end);
static int      cbb_cardbus_mem_open(device_t brdev, int win,
                    uint32_t start, uint32_t end);
static void     cbb_cardbus_auto_open(struct cbb_softc *sc, int type);
static int      cbb_cardbus_activate_resource(device_t brdev, device_t child,
                    struct resource *res);
static int      cbb_cardbus_deactivate_resource(device_t brdev,
                    device_t child, struct resource *res);
static struct resource  *cbb_cardbus_alloc_resource(device_t brdev,
                    device_t child, int type, int rid, rman_res_t start,
                    rman_res_t end, rman_res_t count, u_int flags);
static int      cbb_cardbus_release_resource(device_t brdev, device_t child,
                    struct resource *res);
static int      cbb_cardbus_power_enable_socket(device_t brdev,
                    device_t child);
static int      cbb_cardbus_power_disable_socket(device_t brdev,
                    device_t child);
static int      cbb_func_filt(void *arg);
static void     cbb_func_intr(void *arg);

static void
cbb_remove_res(struct cbb_softc *sc, struct resource *res)
{
        struct cbb_reslist *rle;

        SLIST_FOREACH(rle, &sc->rl, link) {
                if (rle->res == res) {
                        SLIST_REMOVE(&sc->rl, rle, cbb_reslist, link);
                        free(rle, M_DEVBUF);
                        return;
                }
        }
}

static struct resource *
cbb_find_res(struct cbb_softc *sc, int type, int rid)
{
        struct cbb_reslist *rle;

        SLIST_FOREACH(rle, &sc->rl, link)
                if (SYS_RES_MEMORY == rle->type && rid == rle->rid)
                        return (rle->res);
        return (NULL);
}

static void
cbb_insert_res(struct cbb_softc *sc, struct resource *res, int type,
    int rid)
{
        struct cbb_reslist *rle;

        /*
         * Need to record allocated resource so we can iterate through
         * it later.
         */
        rle = malloc(sizeof(struct cbb_reslist), M_DEVBUF, M_NOWAIT);
        if (rle == NULL)
                panic("cbb_cardbus_alloc_resource: can't record entry!");
        rle->res = res;
        rle->type = type;
        rle->rid = rid;
        SLIST_INSERT_HEAD(&sc->rl, rle, link);
}

static void
cbb_destroy_res(struct cbb_softc *sc)
{
        struct cbb_reslist *rle;

        while ((rle = SLIST_FIRST(&sc->rl)) != NULL) {
                device_printf(sc->dev, "Danger Will Robinson: Resource "
                    "left allocated!  This is a bug... "
                    "(rid=%x, type=%d, addr=%jx)\n", rle->rid, rle->type,
                    rman_get_start(rle->res));
                SLIST_REMOVE_HEAD(&sc->rl, link);
                free(rle, M_DEVBUF);
        }
}

/*
 * Disable function interrupts by telling the bridge to generate IRQ1
 * interrupts.  These interrupts aren't really generated by the chip, since
 * IRQ1 is reserved.  Some chipsets assert INTA# inappropriately during
 * initialization, so this helps to work around the problem.
 *
 * XXX We can't do this workaround for all chipsets, because this
 * XXX causes interference with the keyboard because somechipsets will
 * XXX actually signal IRQ1 over their serial interrupt connections to
 * XXX the south bridge.  Disable it it for now.
 */
void
cbb_disable_func_intr(struct cbb_softc *sc)
{
#if 0
        uint8_t reg;

        reg = (exca_getb(&sc->exca, EXCA_INTR) & ~EXCA_INTR_IRQ_MASK) | 
            EXCA_INTR_IRQ_RESERVED1;
        exca_putb(&sc->exca, EXCA_INTR, reg);
#endif
}

/*
 * Enable function interrupts.  We turn on function interrupts when the card
 * requests an interrupt.  The PCMCIA standard says that we should set
 * the lower 4 bits to 0 to route via PCI.  Note: we call this for both
 * CardBus and R2 (PC Card) cases, but it should have no effect on CardBus
 * cards.
 */
static void
cbb_enable_func_intr(struct cbb_softc *sc)
{
        uint8_t reg;

        reg = (exca_getb(&sc->exca, EXCA_INTR) & ~EXCA_INTR_IRQ_MASK) | 
            EXCA_INTR_IRQ_NONE;
        PCI_MASK_CONFIG(sc->dev, CBBR_BRIDGECTRL,
            & ~CBBM_BRIDGECTRL_INTR_IREQ_ISA_EN, 2);
        exca_putb(&sc->exca, EXCA_INTR, reg);
}

int
cbb_detach(device_t brdev)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        int error;

        error = bus_generic_detach(brdev);
        if (error != 0)
                return (error);

        /* Turn off the interrupts */
        cbb_set(sc, CBB_SOCKET_MASK, 0);

        /* reset 16-bit pcmcia bus */
        exca_clrb(&sc->exca, EXCA_INTR, EXCA_INTR_RESET);

        /* turn off power */
        cbb_power(brdev, CARD_OFF);

        /* Ack the interrupt */
        cbb_set(sc, CBB_SOCKET_EVENT, 0xffffffff);

        /*
         * Wait for the thread to die.  kproc_exit will do a wakeup
         * on the event thread's struct proc * so that we know it is
         * safe to proceed.  IF the thread is running, set the please
         * die flag and wait for it to comply.  Since the wakeup on
         * the event thread happens only in kproc_exit, we don't
         * need to loop here.
         */
        bus_teardown_intr(brdev, sc->irq_res, sc->intrhand);
        mtx_lock(&sc->mtx);
        sc->flags |= CBB_KTHREAD_DONE;
        while (sc->flags & CBB_KTHREAD_RUNNING) {
                DEVPRINTF((sc->dev, "Waiting for thread to die\n"));
                wakeup(&sc->intrhand);
                msleep(sc->event_thread, &sc->mtx, PWAIT, "cbbun", 0);
        }
        mtx_unlock(&sc->mtx);

        bus_release_resource(brdev, SYS_RES_IRQ, 0, sc->irq_res);
        bus_release_resource(brdev, SYS_RES_MEMORY, CBBR_SOCKBASE,
            sc->base_res);
        mtx_destroy(&sc->mtx);
        return (0);
}

int
cbb_setup_intr(device_t dev, device_t child, struct resource *irq,
  int flags, driver_filter_t *filt, driver_intr_t *intr, void *arg,
   void **cookiep)
{
        struct cbb_intrhand *ih;
        struct cbb_softc *sc = device_get_softc(dev);
        int err;

        if (filt == NULL && intr == NULL)
                return (EINVAL);
        ih = malloc(sizeof(struct cbb_intrhand), M_DEVBUF, M_NOWAIT);
        if (ih == NULL)
                return (ENOMEM);
        *cookiep = ih;
        ih->filt = filt;
        ih->intr = intr;
        ih->arg = arg;
        ih->sc = sc;
        /*
         * XXX need to turn on ISA interrupts, if we ever support them, but
         * XXX for now that's all we need to do.
         */
        err = BUS_SETUP_INTR(device_get_parent(dev), child, irq, flags,
            filt ? cbb_func_filt : NULL, intr ? cbb_func_intr : NULL, ih,
            &ih->cookie);
        if (err != 0) {
                free(ih, M_DEVBUF);
                return (err);
        }
        cbb_enable_func_intr(sc);
        sc->cardok = 1;
        return 0;
}

int
cbb_teardown_intr(device_t dev, device_t child, struct resource *irq,
    void *cookie)
{
        struct cbb_intrhand *ih;
        int err;

        /* XXX Need to do different things for ISA interrupts. */
        ih = (struct cbb_intrhand *) cookie;
        err = BUS_TEARDOWN_INTR(device_get_parent(dev), child, irq,
            ih->cookie);
        if (err != 0)
                return (err);
        free(ih, M_DEVBUF);
        return (0);
}

void
cbb_driver_added(device_t brdev, driver_t *driver)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        device_t *devlist;
        device_t dev;
        int tmp;
        int numdevs;
        int wake = 0;

        DEVICE_IDENTIFY(driver, brdev);
        tmp = device_get_children(brdev, &devlist, &numdevs);
        if (tmp != 0) {
                device_printf(brdev, "Cannot get children list, no reprobe\n");
                return;
        }
        for (tmp = 0; tmp < numdevs; tmp++) {
                dev = devlist[tmp];
                if (device_get_state(dev) == DS_NOTPRESENT &&
                    device_probe_and_attach(dev) == 0)
                        wake++;
        }
        free(devlist, M_TEMP);

        if (wake > 0)
                wakeup(&sc->intrhand);
}

void
cbb_child_detached(device_t brdev, device_t child)
{
        struct cbb_softc *sc = device_get_softc(brdev);

        /* I'm not sure we even need this */
        if (child != sc->cbdev && child != sc->exca.pccarddev)
                device_printf(brdev, "Unknown child detached: %s\n",
                    device_get_nameunit(child));
}

/************************************************************************/
/* Kthreads                                                             */
/************************************************************************/

void
cbb_event_thread(void *arg)
{
        struct cbb_softc *sc = arg;
        uint32_t status;
        int err;
        int not_a_card = 0;

        /*
         * We need to act as a power sequencer on startup.  Delay 2s/channel
         * to ensure the other channels have had a chance to come up.  We likely
         * should add a lock that's shared on a per-slot basis so that only
         * one power event can happen per slot at a time.
         */
        pause("cbbstart", hz * device_get_unit(sc->dev) * 2);
        mtx_lock(&sc->mtx);
        sc->flags |= CBB_KTHREAD_RUNNING;
        while ((sc->flags & CBB_KTHREAD_DONE) == 0) {
                mtx_unlock(&sc->mtx);
                status = cbb_get(sc, CBB_SOCKET_STATE);
                DPRINTF(("Status is 0x%x\n", status));
                if (!CBB_CARD_PRESENT(status)) {
                        not_a_card = 0;         /* We know card type */
                        cbb_removal(sc);
                } else if (status & CBB_STATE_NOT_A_CARD) {
                        /*
                         * Up to 10 times, try to rescan the card when we see
                         * NOT_A_CARD.  10 is somehwat arbitrary.  When this
                         * pathology hits, there's a ~40% chance each try will
                         * fail.  10 tries takes about 5s and results in a
                         * 99.99% certainty of the results.
                         */
                        if (not_a_card++ < 10) {
                                DEVPRINTF((sc->dev,
                                    "Not a card bit set, rescanning\n"));
                                cbb_setb(sc, CBB_SOCKET_FORCE, CBB_FORCE_CV_TEST);
                        } else {
                                device_printf(sc->dev,
                                    "Can't determine card type\n");
                        }
                } else {
                        not_a_card = 0;         /* We know card type */
                        cbb_insert(sc);
                }

                /*
                 * First time through we need to tell mountroot that we're
                 * done.
                 */
                if (sc->sc_root_token) {
                        root_mount_rel(sc->sc_root_token);
                        sc->sc_root_token = NULL;
                }

                /*
                 * Wait until it has been 250ms since the last time we
                 * get an interrupt.  We handle the rest of the interrupt
                 * at the top of the loop.  Although we clear the bit in the
                 * ISR, we signal sc->cv from the detach path after we've
                 * set the CBB_KTHREAD_DONE bit, so we can't do a simple
                 * 250ms sleep here.
                 *
                 * In our ISR, we turn off the card changed interrupt.  Turn
                 * them back on here before we wait for them to happen.  We
                 * turn them on/off so that we can tolerate a large latency
                 * between the time we signal cbb_event_thread and it gets
                 * a chance to run.
                 */
                mtx_lock(&sc->mtx);
                cbb_setb(sc, CBB_SOCKET_MASK, CBB_SOCKET_MASK_CD | CBB_SOCKET_MASK_CSTS);
                msleep(&sc->intrhand, &sc->mtx, 0, "-", 0);
                err = 0;
                while (err != EWOULDBLOCK &&
                    (sc->flags & CBB_KTHREAD_DONE) == 0)
                        err = msleep(&sc->intrhand, &sc->mtx, 0, "-", hz / 5);
        }
        DEVPRINTF((sc->dev, "Thread terminating\n"));
        sc->flags &= ~CBB_KTHREAD_RUNNING;
        mtx_unlock(&sc->mtx);
        kproc_exit(0);
}

/************************************************************************/
/* Insert/removal                                                       */
/************************************************************************/

static void
cbb_insert(struct cbb_softc *sc)
{
        uint32_t sockevent, sockstate;

        sockevent = cbb_get(sc, CBB_SOCKET_EVENT);
        sockstate = cbb_get(sc, CBB_SOCKET_STATE);

        DEVPRINTF((sc->dev, "card inserted: event=0x%08x, state=%08x\n",
            sockevent, sockstate));

        if (sockstate & CBB_STATE_R2_CARD) {
                if (device_is_attached(sc->exca.pccarddev)) {
                        sc->flags |= CBB_16BIT_CARD;
                        exca_insert(&sc->exca);
                } else {
                        device_printf(sc->dev,
                            "16-bit card inserted, but no pccard bus.\n");
                }
        } else if (sockstate & CBB_STATE_CB_CARD) {
                if (device_is_attached(sc->cbdev)) {
                        sc->flags &= ~CBB_16BIT_CARD;
                        CARD_ATTACH_CARD(sc->cbdev);
                } else {
                        device_printf(sc->dev,
                            "CardBus card inserted, but no cardbus bus.\n");
                }
        } else {
                /*
                 * We should power the card down, and try again a couple of
                 * times if this happens. XXX
                 */
                device_printf(sc->dev, "Unsupported card type detected\n");
        }
}

static void
cbb_removal(struct cbb_softc *sc)
{
        sc->cardok = 0;
        if (sc->flags & CBB_16BIT_CARD) {
                exca_removal(&sc->exca);
        } else {
                if (device_is_attached(sc->cbdev))
                        CARD_DETACH_CARD(sc->cbdev);
        }
        cbb_destroy_res(sc);
}

/************************************************************************/
/* Interrupt Handler                                                    */
/************************************************************************/

static int
cbb_func_filt(void *arg)
{
        struct cbb_intrhand *ih = (struct cbb_intrhand *)arg;
        struct cbb_softc *sc = ih->sc;

        /*
         * Make sure that the card is really there.
         */
        if (!sc->cardok)
                return (FILTER_STRAY);
        if (!CBB_CARD_PRESENT(cbb_get(sc, CBB_SOCKET_STATE))) {
                sc->cardok = 0;
                return (FILTER_HANDLED);
        }

        return ((*ih->filt)(ih->arg));
}

static void
cbb_func_intr(void *arg)
{
        struct cbb_intrhand *ih = (struct cbb_intrhand *)arg;
        struct cbb_softc *sc = ih->sc;

        /*
         * While this check may seem redundant, it helps close a race
         * condition.  If the card is ejected after the filter runs, but
         * before this ISR can be scheduled, then we need to do the same
         * filtering to prevent the card's ISR from being called.  One could
         * argue that the card's ISR should be able to cope, but experience
         * has shown they can't always.  This mitigates the problem by making
         * the race quite a bit smaller.  Properly written client ISRs should
         * cope with the card going away in the middle of the ISR.  We assume
         * that drivers that are sophisticated enough to use filters don't
         * need our protection.  This also allows us to ensure they *ARE*
         * called if their filter said they needed to be called.
         */
        if (ih->filt == NULL) {
                if (!sc->cardok)
                        return;
                if (!CBB_CARD_PRESENT(cbb_get(sc, CBB_SOCKET_STATE))) {
                        sc->cardok = 0;
                        return;
                }
        }

        ih->intr(ih->arg);
}

/************************************************************************/
/* Generic Power functions                                              */
/************************************************************************/

static uint32_t
cbb_detect_voltage(device_t brdev)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        uint32_t psr;
        uint32_t vol = CARD_UKN_CARD;

        psr = cbb_get(sc, CBB_SOCKET_STATE);

        if (psr & CBB_STATE_5VCARD && psr & CBB_STATE_5VSOCK)
                vol |= CARD_5V_CARD;
        if (psr & CBB_STATE_3VCARD && psr & CBB_STATE_3VSOCK)
                vol |= CARD_3V_CARD;
        if (psr & CBB_STATE_XVCARD && psr & CBB_STATE_XVSOCK)
                vol |= CARD_XV_CARD;
        if (psr & CBB_STATE_YVCARD && psr & CBB_STATE_YVSOCK)
                vol |= CARD_YV_CARD;

        return (vol);
}

static uint8_t
cbb_o2micro_power_hack(struct cbb_softc *sc)
{
        uint8_t reg;

        /*
         * Issue #2: INT# not qualified with IRQ Routing Bit.  An
         * unexpected PCI INT# may be generated during PC Card
         * initialization even with the IRQ Routing Bit Set with some
         * PC Cards.
         *
         * This is a two part issue.  The first part is that some of
         * our older controllers have an issue in which the slot's PCI
         * INT# is NOT qualified by the IRQ routing bit (PCI reg. 3Eh
         * bit 7).  Regardless of the IRQ routing bit, if NO ISA IRQ
         * is selected (ExCA register 03h bits 3:0, of the slot, are
         * cleared) we will generate INT# if IREQ# is asserted.  The
         * second part is because some PC Cards prematurally assert
         * IREQ# before the ExCA registers are fully programmed.  This
         * in turn asserts INT# because ExCA register 03h bits 3:0
         * (ISA IRQ Select) are not yet programmed.
         *
         * The fix for this issue, which will work for any controller
         * (old or new), is to set ExCA register 03h bits 3:0 = 0001b
         * (select IRQ1), of the slot, before turning on slot power.
         * Selecting IRQ1 will result in INT# NOT being asserted
         * (because IRQ1 is selected), and IRQ1 won't be asserted
         * because our controllers don't generate IRQ1.
         *
         * Other, non O2Micro controllers will generate irq 1 in some
         * situations, so we can't do this hack for everybody.  Reports of
         * keyboard controller's interrupts being suppressed occurred when
         * we did this.
         */
        reg = exca_getb(&sc->exca, EXCA_INTR);
        exca_putb(&sc->exca, EXCA_INTR, (reg & 0xf0) | 1);
        return (reg);
}

/*
 * Restore the damage that cbb_o2micro_power_hack does to EXCA_INTR so
 * we don't have an interrupt storm on power on.  This has the effect of
 * disabling card status change interrupts for the duration of poweron.
 */
static void
cbb_o2micro_power_hack2(struct cbb_softc *sc, uint8_t reg)
{
        exca_putb(&sc->exca, EXCA_INTR, reg);
}

int
cbb_power(device_t brdev, int volts)
{
        uint32_t status, sock_ctrl, reg_ctrl, mask;
        struct cbb_softc *sc = device_get_softc(brdev);
        int cnt, sane;
        int retval = 0;
        int on = 0;
        uint8_t reg = 0;

        sock_ctrl = cbb_get(sc, CBB_SOCKET_CONTROL);

        sock_ctrl &= ~CBB_SOCKET_CTRL_VCCMASK;
        switch (volts & CARD_VCCMASK) {
        case 5:
                sock_ctrl |= CBB_SOCKET_CTRL_VCC_5V;
                on++;
                break;
        case 3:
                sock_ctrl |= CBB_SOCKET_CTRL_VCC_3V;
                on++;
                break;
        case XV:
                sock_ctrl |= CBB_SOCKET_CTRL_VCC_XV;
                on++;
                break;
        case YV:
                sock_ctrl |= CBB_SOCKET_CTRL_VCC_YV;
                on++;
                break;
        case 0:
                break;
        default:
                return (0);                     /* power NEVER changed */
        }

        /* VPP == VCC */
        sock_ctrl &= ~CBB_SOCKET_CTRL_VPPMASK;
        sock_ctrl |= ((sock_ctrl >> 4) & 0x07);

        if (cbb_get(sc, CBB_SOCKET_CONTROL) == sock_ctrl)
                return (1); /* no change necessary */
        DEVPRINTF((sc->dev, "cbb_power: %dV\n", volts));
        if (volts != 0 && sc->chipset == CB_O2MICRO)
                reg = cbb_o2micro_power_hack(sc);

        /*
         * We have to mask the card change detect interrupt while we're
         * messing with the power.  It is allowed to bounce while we're
         * messing with power as things settle down.  In addition, we mask off
         * the card's function interrupt by routing it via the ISA bus.  This
         * bit generally only affects 16-bit cards.  Some bridges allow one to
         * set another bit to have it also affect 32-bit cards.  Since 32-bit
         * cards are required to be better behaved, we don't bother to get
         * into those bridge specific features.
         *
         * XXX I wonder if we need to enable the READY bit interrupt in the
         * EXCA CSC register for 16-bit cards, and disable the CD bit?
         */
        mask = cbb_get(sc, CBB_SOCKET_MASK);
        mask |= CBB_SOCKET_MASK_POWER;
        mask &= ~CBB_SOCKET_MASK_CD;
        cbb_set(sc, CBB_SOCKET_MASK, mask);
        PCI_MASK_CONFIG(brdev, CBBR_BRIDGECTRL,
            |CBBM_BRIDGECTRL_INTR_IREQ_ISA_EN, 2);
        cbb_set(sc, CBB_SOCKET_CONTROL, sock_ctrl);
        if (on) {
                mtx_lock(&sc->mtx);
                cnt = sc->powerintr;
                /*
                 * We have a shortish timeout of 500ms here.  Some bridges do
                 * not generate a POWER_CYCLE event for 16-bit cards.  In
                 * those cases, we have to cope the best we can, and having
                 * only a short delay is better than the alternatives.  Others
                 * raise the power cycle a smidge before it is really ready.
                 * We deal with those below.
                 */
                sane = 10;
                while (!(cbb_get(sc, CBB_SOCKET_STATE) & CBB_STATE_POWER_CYCLE) &&
                    cnt == sc->powerintr && sane-- > 0)
                        msleep(&sc->powerintr, &sc->mtx, 0, "-", hz / 20);
                mtx_unlock(&sc->mtx);

                /*
                 * Relax for 100ms.  Some bridges appear to assert this signal
                 * right away, but before the card has stabilized.  Other
                 * cards need need more time to cope up reliabily.
                 * Experiments with troublesome setups show this to be a
                 * "cheap" way to enhance reliabilty.  We need not do this for
                 * "off" since we don't touch the card after we turn it off.
                 */
                pause("cbbPwr", min(hz / 10, 1));

                /*
                 * The TOPIC95B requires a little bit extra time to get its
                 * act together, so delay for an additional 100ms.  Also as
                 * documented below, it doesn't seem to set the POWER_CYCLE
                 * bit, so don't whine if it never came on.
                 */
                if (sc->chipset == CB_TOPIC95)
                        pause("cbb95B", hz / 10);
                else if (sane <= 0)
                        device_printf(sc->dev, "power timeout, doom?\n");
        }

        /*
         * After the power is good, we can turn off the power interrupt.
         * However, the PC Card standard says that we must delay turning the
         * CD bit back on for a bit to allow for bouncyness on power down
         * (recall that we don't wait above for a power down, since we don't
         * get an interrupt for that).  We're called either from the suspend
         * code in which case we don't want to turn card change on again, or
         * we're called from the card insertion code, in which case the cbb
         * thread will turn it on for us before it waits to be woken by a
         * change event.
         *
         * NB: Topic95B doesn't set the power cycle bit.  we assume that
         * both it and the TOPIC95 behave the same.
         */
        cbb_clrb(sc, CBB_SOCKET_MASK, CBB_SOCKET_MASK_POWER);
        status = cbb_get(sc, CBB_SOCKET_STATE);
        if (on && sc->chipset != CB_TOPIC95) {
                if ((status & CBB_STATE_POWER_CYCLE) == 0)
                        device_printf(sc->dev, "Power not on?\n");
        }
        if (status & CBB_STATE_BAD_VCC_REQ) {
                device_printf(sc->dev, "Bad Vcc requested\n");  
                /*
                 * Turn off the power, and try again.  Retrigger other
                 * active interrupts via force register.  From NetBSD
                 * PR 36652, coded by me to description there.
                 */
                sock_ctrl &= ~CBB_SOCKET_CTRL_VCCMASK;
                sock_ctrl &= ~CBB_SOCKET_CTRL_VPPMASK;
                cbb_set(sc, CBB_SOCKET_CONTROL, sock_ctrl);
                status &= ~CBB_STATE_BAD_VCC_REQ;
                status &= ~CBB_STATE_DATA_LOST;
                status |= CBB_FORCE_CV_TEST;
                cbb_set(sc, CBB_SOCKET_FORCE, status);
                goto done;
        }
        if (sc->chipset == CB_TOPIC97) {
                reg_ctrl = pci_read_config(sc->dev, TOPIC_REG_CTRL, 4);
                reg_ctrl &= ~TOPIC97_REG_CTRL_TESTMODE;
                if (on)
                        reg_ctrl |= TOPIC97_REG_CTRL_CLKRUN_ENA;
                else
                        reg_ctrl &= ~TOPIC97_REG_CTRL_CLKRUN_ENA;
                pci_write_config(sc->dev, TOPIC_REG_CTRL, reg_ctrl, 4);
        }
        retval = 1;
done:;
        if (volts != 0 && sc->chipset == CB_O2MICRO)
                cbb_o2micro_power_hack2(sc, reg);
        return (retval);
}

static int
cbb_current_voltage(device_t brdev)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        uint32_t ctrl;

        ctrl = cbb_get(sc, CBB_SOCKET_CONTROL);
        switch (ctrl & CBB_SOCKET_CTRL_VCCMASK) {
        case CBB_SOCKET_CTRL_VCC_5V:
                return CARD_5V_CARD;
        case CBB_SOCKET_CTRL_VCC_3V:
                return CARD_3V_CARD;
        case CBB_SOCKET_CTRL_VCC_XV:
                return CARD_XV_CARD;
        case CBB_SOCKET_CTRL_VCC_YV:
                return CARD_YV_CARD;
        }
        return 0;
}

/*
 * detect the voltage for the card, and set it.  Since the power
 * used is the square of the voltage, lower voltages is a big win
 * and what Windows does (and what Microsoft prefers).  The MS paper
 * also talks about preferring the CIS entry as well, but that has
 * to be done elsewhere.  We also optimize power sequencing here
 * and don't change things if we're already powered up at a supported
 * voltage.
 *
 * In addition, we power up with OE disabled.  We'll set it later
 * in the power up sequence.
 */
static int
cbb_do_power(device_t brdev)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        uint32_t voltage, curpwr;
        uint32_t status;

        /* Don't enable OE (output enable) until power stable */
        exca_clrb(&sc->exca, EXCA_PWRCTL, EXCA_PWRCTL_OE);

        voltage = cbb_detect_voltage(brdev);
        curpwr = cbb_current_voltage(brdev);
        status = cbb_get(sc, CBB_SOCKET_STATE);
        if ((status & CBB_STATE_POWER_CYCLE) && (voltage & curpwr))
                return 0;
        /* Prefer lowest voltage supported */
        cbb_power(brdev, CARD_OFF);
        if (voltage & CARD_YV_CARD)
                cbb_power(brdev, CARD_VCC(YV));
        else if (voltage & CARD_XV_CARD)
                cbb_power(brdev, CARD_VCC(XV));
        else if (voltage & CARD_3V_CARD)
                cbb_power(brdev, CARD_VCC(3));
        else if (voltage & CARD_5V_CARD)
                cbb_power(brdev, CARD_VCC(5));
        else {
                device_printf(brdev, "Unknown card voltage\n");
                return (ENXIO);
        }
        return (0);
}

/************************************************************************/
/* CardBus power functions                                              */
/************************************************************************/

static int
cbb_cardbus_reset_power(device_t brdev, device_t child, int on)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        uint32_t b, h;
        int delay, count, zero_seen, func;

        /*
         * Asserting reset for 20ms is necessary for most bridges.  For some
         * reason, the Ricoh RF5C47x bridges need it asserted for 400ms.  The
         * root cause of this is unknown, and NetBSD does the same thing.
         */
        delay = sc->chipset == CB_RF5C47X ? 400 : 20;
        PCI_MASK_CONFIG(brdev, CBBR_BRIDGECTRL, |CBBM_BRIDGECTRL_RESET, 2);
        pause("cbbP3", hz * delay / 1000);

        /*
         * If a card exists and we're turning it on, take it out of reset.
         * After clearing reset, wait up to 1.1s for the first configuration
         * register (vendor/product) configuration register of device 0.0 to
         * become != 0xffffffff.  The PCMCIA PC Card Host System Specification
         * says that when powering up the card, the PCI Spec v2.1 must be
         * followed.  In PCI spec v2.2 Table 4-6, Trhfa (Reset High to first
         * Config Access) is at most 2^25 clocks, or just over 1s.  Section
         * 2.2.1 states any card not ready to participate in bus transactions
         * must tristate its outputs.  Therefore, any access to its
         * configuration registers must be ignored.  In that state, the config
         * reg will read 0xffffffff.  Section 6.2.1 states a vendor id of
         * 0xffff is invalid, so this can never match a real card.  Print a
         * warning if it never returns a real id.  The PCMCIA PC Card
         * Electrical Spec Section 5.2.7.1 implies only device 0 is present on
         * a cardbus bus, so that's the only register we check here.
         */
        if (on && CBB_CARD_PRESENT(cbb_get(sc, CBB_SOCKET_STATE))) {
                PCI_MASK_CONFIG(brdev, CBBR_BRIDGECTRL,
                    &~CBBM_BRIDGECTRL_RESET, 2);
                b = pcib_get_bus(child);
                count = 1100 / 20;
                do {
                        pause("cbbP4", hz * 2 / 100);
                } while (PCIB_READ_CONFIG(brdev, b, 0, 0, PCIR_DEVVENDOR, 4) ==
                    0xfffffffful && --count >= 0);
                if (count < 0)
                        device_printf(brdev, "Warning: Bus reset timeout\n");

                /*
                 * Some cards (so far just an atheros card I have) seem to
                 * come out of reset in a funky state. They report they are
                 * multi-function cards, but have nonsense for some of the
                 * higher functions.  So if the card claims to be MFDEV, and
                 * any of the higher functions' ID is 0, then we've hit the
                 * bug and we'll try again.
                 */
                h = PCIB_READ_CONFIG(brdev, b, 0, 0, PCIR_HDRTYPE, 1);
                if ((h & PCIM_MFDEV) == 0)
                        return 0;
                zero_seen = 0;
                for (func = 1; func < 8; func++) {
                        h = PCIB_READ_CONFIG(brdev, b, 0, func,
                            PCIR_DEVVENDOR, 4);
                        if (h == 0)
                                zero_seen++;
                }
                if (!zero_seen)
                        return 0;
                return (EINVAL);
        }
        return 0;
}

static int
cbb_cardbus_power_disable_socket(device_t brdev, device_t child)
{
        cbb_power(brdev, CARD_OFF);
        cbb_cardbus_reset_power(brdev, child, 0);
        return (0);
}

static int
cbb_cardbus_power_enable_socket(device_t brdev, device_t child)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        int err, count;

        if (!CBB_CARD_PRESENT(cbb_get(sc, CBB_SOCKET_STATE)))
                return (ENODEV);

        count = 10;
        do {
                err = cbb_do_power(brdev);
                if (err)
                        return (err);
                err = cbb_cardbus_reset_power(brdev, child, 1);
                if (err) {
                        device_printf(brdev, "Reset failed, trying again.\n");
                        cbb_cardbus_power_disable_socket(brdev, child);
                        pause("cbbErr1", hz / 10); /* wait 100ms */
                }
        } while (err != 0 && count-- > 0);
        return (0);
}

/************************************************************************/
/* CardBus Resource                                                     */
/************************************************************************/

static void
cbb_activate_window(device_t brdev, int type)
{

        PCI_ENABLE_IO(device_get_parent(brdev), brdev, type);
}

static int
cbb_cardbus_io_open(device_t brdev, int win, uint32_t start, uint32_t end)
{
        int basereg;
        int limitreg;

        if ((win < 0) || (win > 1)) {
                DEVPRINTF((brdev,
                    "cbb_cardbus_io_open: window out of range %d\n", win));
                return (EINVAL);
        }

        basereg = win * 8 + CBBR_IOBASE0;
        limitreg = win * 8 + CBBR_IOLIMIT0;

        pci_write_config(brdev, basereg, start, 4);
        pci_write_config(brdev, limitreg, end, 4);
        cbb_activate_window(brdev, SYS_RES_IOPORT);
        return (0);
}

static int
cbb_cardbus_mem_open(device_t brdev, int win, uint32_t start, uint32_t end)
{
        int basereg;
        int limitreg;

        if ((win < 0) || (win > 1)) {
                DEVPRINTF((brdev,
                    "cbb_cardbus_mem_open: window out of range %d\n", win));
                return (EINVAL);
        }

        basereg = win * 8 + CBBR_MEMBASE0;
        limitreg = win * 8 + CBBR_MEMLIMIT0;

        pci_write_config(brdev, basereg, start, 4);
        pci_write_config(brdev, limitreg, end, 4);
        cbb_activate_window(brdev, SYS_RES_MEMORY);
        return (0);
}

#define START_NONE 0xffffffff
#define END_NONE 0

static void
cbb_cardbus_auto_open(struct cbb_softc *sc, int type)
{
        uint32_t starts[2];
        uint32_t ends[2];
        struct cbb_reslist *rle;
        int align, i;
        uint32_t reg;

        starts[0] = starts[1] = START_NONE;
        ends[0] = ends[1] = END_NONE;

        if (type == SYS_RES_MEMORY)
                align = CBB_MEMALIGN;
        else if (type == SYS_RES_IOPORT)
                align = CBB_IOALIGN;
        else
                align = 1;

        SLIST_FOREACH(rle, &sc->rl, link) {
                if (rle->type != type)
                        continue;
                if (rle->res == NULL)
                        continue;
                if (!(rman_get_flags(rle->res) & RF_ACTIVE))
                        continue;
                if (rman_get_flags(rle->res) & RF_PREFETCHABLE)
                        i = 1;
                else
                        i = 0;
                if (rman_get_start(rle->res) < starts[i])
                        starts[i] = rman_get_start(rle->res);
                if (rman_get_end(rle->res) > ends[i])
                        ends[i] = rman_get_end(rle->res);
        }
        for (i = 0; i < 2; i++) {
                if (starts[i] == START_NONE)
                        continue;
                starts[i] &= ~(align - 1);
                ends[i] = roundup2(ends[i], align) - 1;
        }
        if (starts[0] != START_NONE && starts[1] != START_NONE) {
                if (starts[0] < starts[1]) {
                        if (ends[0] > starts[1]) {
                                device_printf(sc->dev, "Overlapping ranges"
                                    " for prefetch and non-prefetch memory\n");
                                return;
                        }
                } else {
                        if (ends[1] > starts[0]) {
                                device_printf(sc->dev, "Overlapping ranges"
                                    " for prefetch and non-prefetch memory\n");
                                return;
                        }
                }
        }

        if (type == SYS_RES_MEMORY) {
                cbb_cardbus_mem_open(sc->dev, 0, starts[0], ends[0]);
                cbb_cardbus_mem_open(sc->dev, 1, starts[1], ends[1]);
                reg = pci_read_config(sc->dev, CBBR_BRIDGECTRL, 2);
                reg &= ~(CBBM_BRIDGECTRL_PREFETCH_0 |
                    CBBM_BRIDGECTRL_PREFETCH_1);
                if (starts[1] != START_NONE)
                        reg |= CBBM_BRIDGECTRL_PREFETCH_1;
                pci_write_config(sc->dev, CBBR_BRIDGECTRL, reg, 2);
                if (bootverbose) {
                        device_printf(sc->dev, "Opening memory:\n");
                        if (starts[0] != START_NONE)
                                device_printf(sc->dev, "Normal: %#x-%#x\n",
                                    starts[0], ends[0]);
                        if (starts[1] != START_NONE)
                                device_printf(sc->dev, "Prefetch: %#x-%#x\n",
                                    starts[1], ends[1]);
                }
        } else if (type == SYS_RES_IOPORT) {
                cbb_cardbus_io_open(sc->dev, 0, starts[0], ends[0]);
                cbb_cardbus_io_open(sc->dev, 1, starts[1], ends[1]);
                if (bootverbose && starts[0] != START_NONE)
                        device_printf(sc->dev, "Opening I/O: %#x-%#x\n",
                            starts[0], ends[0]);
        }
}

static int
cbb_cardbus_activate_resource(device_t brdev, device_t child,
    struct resource *res)
{
        int ret;

        ret = BUS_ACTIVATE_RESOURCE(device_get_parent(brdev), child,
            res);
        if (ret != 0)
                return (ret);
        cbb_cardbus_auto_open(device_get_softc(brdev), rman_get_type(res));
        return (0);
}

static int
cbb_cardbus_deactivate_resource(device_t brdev, device_t child,
    struct resource *res)
{
        int ret;

        ret = BUS_DEACTIVATE_RESOURCE(device_get_parent(brdev), child,
            res);
        if (ret != 0)
                return (ret);
        cbb_cardbus_auto_open(device_get_softc(brdev), rman_get_type(res));
        return (0);
}

static struct resource *
cbb_cardbus_alloc_resource(device_t brdev, device_t child, int type,
    int rid, rman_res_t start, rman_res_t end, rman_res_t count, u_int flags)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        int tmp;
        struct resource *res;
        rman_res_t align;

        switch (type) {
        case SYS_RES_IRQ:
                tmp = rman_get_start(sc->irq_res);
                if (start > tmp || end < tmp || count != 1) {
                        device_printf(child, "requested interrupt %jd-%jd,"
                            "count = %jd not supported by cbb\n",
                            start, end, count);
                        return (NULL);
                }
                start = end = tmp;
                flags |= RF_SHAREABLE;
                break;
        case SYS_RES_IOPORT:
                if (start <= cbb_start_32_io)
                        start = cbb_start_32_io;
                if (end < start)
                        end = start;
                if (count > (1 << RF_ALIGNMENT(flags)))
                        flags = (flags & ~RF_ALIGNMENT_MASK) | 
                            rman_make_alignment_flags(count);
                break;
        case SYS_RES_MEMORY:
                if (start <= cbb_start_mem)
                        start = cbb_start_mem;
                if (end < start)
                        end = start;
                if (count < CBB_MEMALIGN)
                        align = CBB_MEMALIGN;
                else
                        align = count;
                if (align > (1 << RF_ALIGNMENT(flags)))
                        flags = (flags & ~RF_ALIGNMENT_MASK) | 
                            rman_make_alignment_flags(align);
                break;
        }
        res = BUS_ALLOC_RESOURCE(device_get_parent(brdev), child, type, rid,
            start, end, count, flags & ~RF_ACTIVE);
        if (res == NULL) {
                printf("cbb alloc res fail type %d rid %x\n", type, rid);
                return (NULL);
        }
        cbb_insert_res(sc, res, type, rid);
        if (flags & RF_ACTIVE)
                if (bus_activate_resource(child, type, rid, res) != 0) {
                        bus_release_resource(child, type, rid, res);
                        return (NULL);
                }

        return (res);
}

static int
cbb_cardbus_release_resource(device_t brdev, device_t child,
    struct resource *res)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        int error;

        if (rman_get_flags(res) & RF_ACTIVE) {
                error = bus_deactivate_resource(child, res);
                if (error != 0)
                        return (error);
        }
        cbb_remove_res(sc, res);
        return (BUS_RELEASE_RESOURCE(device_get_parent(brdev), child,
            res));
}

/************************************************************************/
/* PC Card Power Functions                                              */
/************************************************************************/

static int
cbb_pcic_power_enable_socket(device_t brdev, device_t child)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        int err;

        DPRINTF(("cbb_pcic_socket_enable:\n"));

        /* power down/up the socket to reset */
        err = cbb_do_power(brdev);
        if (err)
                return (err);
        exca_reset(&sc->exca, child);

        return (0);
}

static int
cbb_pcic_power_disable_socket(device_t brdev, device_t child)
{
        struct cbb_softc *sc = device_get_softc(brdev);

        DPRINTF(("cbb_pcic_socket_disable\n"));

        /* Turn off the card's interrupt and leave it in reset, wait 10ms */
        exca_putb(&sc->exca, EXCA_INTR, 0);
        pause("cbbP1", hz / 100);

        /* power down the socket */
        cbb_power(brdev, CARD_OFF);
        exca_putb(&sc->exca, EXCA_PWRCTL, 0);

        /* wait 300ms until power fails (Tpf). */
        pause("cbbP2", hz * 300 / 1000);

        /* enable CSC interrupts */
        exca_putb(&sc->exca, EXCA_INTR, EXCA_INTR_ENABLE);
        return (0);
}

/************************************************************************/
/* POWER methods                                                        */
/************************************************************************/

int
cbb_power_enable_socket(device_t brdev, device_t child)
{
        struct cbb_softc *sc = device_get_softc(brdev);

        if (sc->flags & CBB_16BIT_CARD)
                return (cbb_pcic_power_enable_socket(brdev, child));
        return (cbb_cardbus_power_enable_socket(brdev, child));
}

int
cbb_power_disable_socket(device_t brdev, device_t child)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        if (sc->flags & CBB_16BIT_CARD)
                return (cbb_pcic_power_disable_socket(brdev, child));
        return (cbb_cardbus_power_disable_socket(brdev, child));
}

static int
cbb_pcic_activate_resource(device_t brdev, device_t child,
    struct resource *res)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        int error;

        error = exca_activate_resource(&sc->exca, child, res);
        if (error == 0)
                cbb_activate_window(brdev, rman_get_type(res));
        return (error);
}

static int
cbb_pcic_deactivate_resource(device_t brdev, device_t child,
    struct resource *res)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        return (exca_deactivate_resource(&sc->exca, child, res));
}

static struct resource *
cbb_pcic_alloc_resource(device_t brdev, device_t child, int type, int rid,
    rman_res_t start, rman_res_t end, rman_res_t count, u_int flags)
{
        struct resource *res = NULL;
        struct cbb_softc *sc = device_get_softc(brdev);
        int align;
        int tmp;

        switch (type) {
        case SYS_RES_MEMORY:
                if (start < cbb_start_mem)
                        start = cbb_start_mem;
                if (end < start)
                        end = start;
                if (count < CBB_MEMALIGN)
                        align = CBB_MEMALIGN;
                else
                        align = count;
                if (align > (1 << RF_ALIGNMENT(flags)))
                        flags = (flags & ~RF_ALIGNMENT_MASK) | 
                            rman_make_alignment_flags(align);
                break;
        case SYS_RES_IOPORT:
                if (start < cbb_start_16_io)
                        start = cbb_start_16_io;
                if (end < start)
                        end = start;
                break;
        case SYS_RES_IRQ:
                tmp = rman_get_start(sc->irq_res);
                if (start > tmp || end < tmp || count != 1) {
                        device_printf(child, "requested interrupt %jd-%jd,"
                            "count = %jd not supported by cbb\n",
                            start, end, count);
                        return (NULL);
                }
                flags |= RF_SHAREABLE;
                start = end = rman_get_start(sc->irq_res);
                break;
        }
        res = BUS_ALLOC_RESOURCE(device_get_parent(brdev), child, type, rid,
            start, end, count, flags & ~RF_ACTIVE);
        if (res == NULL)
                return (NULL);
        cbb_insert_res(sc, res, type, rid);
        if (flags & RF_ACTIVE) {
                if (bus_activate_resource(child, type, rid, res) != 0) {
                        bus_release_resource(child, type, rid, res);
                        return (NULL);
                }
        }

        return (res);
}

static int
cbb_pcic_release_resource(device_t brdev, device_t child,
    struct resource *res)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        int error;

        if (rman_get_flags(res) & RF_ACTIVE) {
                error = bus_deactivate_resource(child, res);
                if (error != 0)
                        return (error);
        }
        cbb_remove_res(sc, res);
        return (BUS_RELEASE_RESOURCE(device_get_parent(brdev), child,
            res));
}

/************************************************************************/
/* PC Card methods                                                      */
/************************************************************************/

int
cbb_pcic_set_res_flags(device_t brdev, device_t child, int type, int rid,
    u_long flags)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        struct resource *res;

        if (type != SYS_RES_MEMORY)
                return (EINVAL);
        res = cbb_find_res(sc, type, rid);
        if (res == NULL) {
                device_printf(brdev,
                    "set_res_flags: specified rid not found\n");
                return (ENOENT);
        }
        return (exca_mem_set_flags(&sc->exca, res, flags));
}

int
cbb_pcic_set_memory_offset(device_t brdev, device_t child, int rid,
    uint32_t cardaddr, uint32_t *deltap)
{
        struct cbb_softc *sc = device_get_softc(brdev);
        struct resource *res;

        res = cbb_find_res(sc, SYS_RES_MEMORY, rid);
        if (res == NULL) {
                device_printf(brdev,
                    "set_memory_offset: specified rid not found\n");
                return (ENOENT);
        }
        return (exca_mem_set_offset(&sc->exca, res, cardaddr, deltap));
}

/************************************************************************/
/* BUS Methods                                                          */
/************************************************************************/

int
cbb_activate_resource(device_t brdev, device_t child, struct resource *r)
{
        struct cbb_softc *sc = device_get_softc(brdev);

        if (sc->flags & CBB_16BIT_CARD)
                return (cbb_pcic_activate_resource(brdev, child, r));
        else
                return (cbb_cardbus_activate_resource(brdev, child, r));
}

int
cbb_deactivate_resource(device_t brdev, device_t child, struct resource *r)
{
        struct cbb_softc *sc = device_get_softc(brdev);

        if (sc->flags & CBB_16BIT_CARD)
                return (cbb_pcic_deactivate_resource(brdev, child, r));
        else
                return (cbb_cardbus_deactivate_resource(brdev, child, r));
}

struct resource *
cbb_alloc_resource(device_t brdev, device_t child, int type, int rid,
    rman_res_t start, rman_res_t end, rman_res_t count, u_int flags)
{
        struct cbb_softc *sc = device_get_softc(brdev);

        if (sc->flags & CBB_16BIT_CARD)
                return (cbb_pcic_alloc_resource(brdev, child, type, rid,
                    start, end, count, flags));
        else
                return (cbb_cardbus_alloc_resource(brdev, child, type, rid,
                    start, end, count, flags));
}

int
cbb_release_resource(device_t brdev, device_t child, struct resource *r)
{
        struct cbb_softc *sc = device_get_softc(brdev);

        if (sc->flags & CBB_16BIT_CARD)
                return (cbb_pcic_release_resource(brdev, child, r));
        else
                return (cbb_cardbus_release_resource(brdev, child, r));
}

int
cbb_read_ivar(device_t brdev, device_t child, int which, uintptr_t *result)
{
        struct cbb_softc *sc = device_get_softc(brdev);

        switch (which) {
        case PCIB_IVAR_DOMAIN:
                *result = sc->domain;
                return (0);
        case PCIB_IVAR_BUS:
                *result = sc->bus.sec;
                return (0);
        case EXCA_IVAR_SLOT:
                *result = 0;
                return (0);
        }
        return (ENOENT);
}

int
cbb_write_ivar(device_t brdev, device_t child, int which, uintptr_t value)
{

        switch (which) {
        case PCIB_IVAR_DOMAIN:
                return (EINVAL);
        case PCIB_IVAR_BUS:
                return (EINVAL);
        case EXCA_IVAR_SLOT:
                return (EINVAL);
        }
        return (ENOENT);
}

int
cbb_child_present(device_t parent, device_t child)
{
        struct cbb_softc *sc = (struct cbb_softc *)device_get_softc(parent);
        uint32_t sockstate;

        sockstate = cbb_get(sc, CBB_SOCKET_STATE);
        return (CBB_CARD_PRESENT(sockstate) && sc->cardok);
}