/*- * Copyright (c) 2003 * Bill Paul <wpaul@windriver.com>. All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by Bill Paul. * 4. Neither the name of the author nor the names of any co-contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF * THE POSSIBILITY OF SUCH DAMAGE. * * $FreeBSD: src/sys/dev/mii/rgephyreg.h,v 1.2 2005/01/06 01:42:56 imp Exp $ * $DragonFly: src/sys/dev/netif/mii_layer/rgephyreg.h,v 1.2 2007/09/17 11:29:36 hasso Exp $ */ #ifndef _DEV_MII_RGEPHYREG_H_ #define _DEV_MII_RGEPHYREG_H_ /* * RealTek 8169S/8110S gigE PHY registers */ #define RGEPHY_MII_BMCR 0x00 #define RGEPHY_BMCR_RESET 0x8000 #define RGEPHY_BMCR_LOOP 0x4000 #define RGEPHY_BMCR_SPD0 0x2000 /* speed select, lower bit */ #define RGEPHY_BMCR_AUTOEN 0x1000 /* Autoneg enabled */ #define RGEPHY_BMCR_PDOWN 0x0800 /* Power down */ #define RGEPHY_BMCR_ISO 0x0400 /* Isolate */ #define RGEPHY_BMCR_STARTNEG 0x0200 /* Restart autoneg */ #define RGEPHY_BMCR_FDX 0x0100 /* Duplex mode */ #define RGEPHY_BMCR_CTEST 0x0080 /* Collision test enable */ #define RGEPHY_BMCR_SPD1 0x0040 /* Speed select, upper bit */ #define RGEPHY_S1000 RGEPHY_BMCR_SPD1 /* 1000mbps */ #define RGEPHY_S100 RGEPHY_BMCR_SPD0 /* 100mpbs */ #define RGEPHY_S10 0 /* 10mbps */ #define RGEPHY_MII_BMSR 0x01 #define RGEPHY_BMSR_100T4 0x8000 /* 100 base T4 capable */ #define RGEPHY_BMSR_100TXFDX 0x4000 /* 100 base Tx full duplex capable */ #define RGEPHY_BMSR_100TXHDX 0x2000 /* 100 base Tx half duplex capable */ #define RGEPHY_BMSR_10TFDX 0x1000 /* 10 base T full duplex capable */ #define RGEPHY_BMSR_10THDX 0x0800 /* 10 base T half duplex capable */ #define RGEPHY_BMSR_100T2FDX 0x0400 /* 100 base T2 full duplex capable */ #define RGEPHY_BMSR_100T2HDX 0x0200 /* 100 base T2 half duplex capable */ #define RGEPHY_BMSR_EXTSTS 0x0100 /* Extended status present */ #define RGEPHY_BMSR_PRESUB 0x0040 /* Preamble surpression */ #define RGEPHY_BMSR_ACOMP 0x0020 /* Autoneg complete */ #define RGEPHY_BMSR_RFAULT 0x0010 /* Remote fault condition occured */ #define RGEPHY_BMSR_ANEG 0x0008 /* Autoneg capable */ #define RGEPHY_BMSR_LINK 0x0004 /* Link status */ #define RGEPHY_BMSR_JABBER 0x0002 /* Jabber detected */ #define RGEPHY_BMSR_EXT 0x0001 /* Extended capability */ #define RGEPHY_MII_ANAR 0x04 #define RGEPHY_ANAR_NP 0x8000 /* Next page */ #define RGEPHY_ANAR_RF 0x2000 /* Remote fault */ #define RGEPHY_ANAR_ASP 0x0800 /* Asymmetric Pause */ #define RGEPHY_ANAR_PC 0x0400 /* Pause capable */ #define RGEPHY_ANAR_T4 0x0200 /* local device supports 100bT4 */ #define RGEPHY_ANAR_TX_FD 0x0100 /* local device supports 100bTx FD */ #define RGEPHY_ANAR_TX 0x0080 /* local device supports 100bTx */ #define RGEPHY_ANAR_10_FD 0x0040 /* local device supports 10bT FD */ #define RGEPHY_ANAR_10 0x0020 /* local device supports 10bT */ #define RGEPHY_ANAR_SEL 0x001F /* selector field, 00001=Ethernet */ #define RGEPHY_MII_ANLPAR 0x05 #define RGEPHY_ANLPAR_NP 0x8000 /* Next page */ #define RGEPHY_ANLPAR_RF 0x2000 /* Remote fault */ #define RGEPHY_ANLPAR_ASP 0x0800 /* Asymmetric Pause */ #define RGEPHY_ANLPAR_PC 0x0400 /* Pause capable */ #define RGEPHY_ANLPAR_T4 0x0200 /* link partner supports 100bT4 */ #define RGEPHY_ANLPAR_TX_FD 0x0100 /* link partner supports 100bTx FD */ #define RGEPHY_ANLPAR_TX 0x0080 /* link partner supports 100bTx */ #define RGEPHY_ANLPAR_10_FD 0x0040 /* link partner supports 10bT FD */ #define RGEPHY_ANLPAR_10 0x0020 /* link partner supports 10bT */ #define RGEPHY_ANLPAR_SEL 0x001F /* selector field, 00001=Ethernet */ #define RGEPHY_SEL_TYPE 0x0001 /* ethernet */ #define RGEPHY_MII_ANER 0x06 #define RGEPHY_ANER_PDF 0x0010 /* Parallel detection fault */ #define RGEPHY_ANER_LPNP 0x0008 /* Link partner can next page */ #define RGEPHY_ANER_NP 0x0004 /* Local PHY can next page */ #define RGEPHY_ANER_RX 0x0002 /* Next page received */ #define RGEPHY_ANER_LPAN 0x0001 /* Link partner autoneg capable */ #define RGEPHY_MII_NEXTP 0x07 /* Next page */ #define RGEPHY_MII_NEXTP_LP 0x08 /* Next page of link partner */ #define RGEPHY_MII_1000CTL 0x09 /* 1000baseT control */ #define RGEPHY_1000CTL_TST 0xE000 /* test modes */ #define RGEPHY_1000CTL_MSE 0x1000 /* Master/Slave manual enable */ #define RGEPHY_1000CTL_MSC 0x0800 /* Master/Slave select */ #define RGEPHY_1000CTL_RD 0x0400 /* Repeater/DTE */ #define RGEPHY_1000CTL_AFD 0x0200 /* Advertise full duplex */ #define RGEPHY_1000CTL_AHD 0x0100 /* Advertise half duplex */ #define RGEPHY_TEST_TX_JITTER 0x2000 #define RGEPHY_TEST_TX_JITTER_MASTER_MODE 0x4000 #define RGEPHY_TEST_TX_JITTER_SLAVE_MODE 0x6000 #define RGEPHY_TEST_TX_DISTORTION 0x8000 #define RGEPHY_MII_1000STS 0x0A /* 1000baseT status */ #define RGEPHY_1000STS_MSF 0x8000 /* Master/slave fault */ #define RGEPHY_1000STS_MSR 0x4000 /* Master/slave result */ #define RGEPHY_1000STS_LRS 0x2000 /* Local receiver status */ #define RGEPHY_1000STS_RRS 0x1000 /* Remote receiver status */ #define RGEPHY_1000STS_LPFD 0x0800 /* Link partner can FD */ #define RGEPHY_1000STS_LPHD 0x0400 /* Link partner can HD */ #define RGEPHY_1000STS_IEC 0x00FF /* Idle error count */ #define RGEPHY_MII_EXTSTS 0x0F /* Extended status */ #define RGEPHY_EXTSTS_X_FD_CAP 0x8000 /* 1000base-X FD capable */ #define RGEPHY_EXTSTS_X_HD_CAP 0x4000 /* 1000base-X HD capable */ #define RGEPHY_EXTSTS_T_FD_CAP 0x2000 /* 1000base-T FD capable */ #define RGEPHY_EXTSTS_T_HD_CAP 0x1000 /* 1000base-T HD capable */ /* RTL8211B */ #define RGEPHY_SR 0x11 #define RGEPHY_SR_CROSSOVER (1<< 6) #define RGEPHY_SR_LINK (1<<10) #define RGEPHY_SR_FDX (1<<13) #define RGEPHY_SR_SPEED(X) (((X)>>14)&3) #define RGEPHY_EXT_CR 0x14 /* * Gigabit media status (8169 only) */ #define RE_GMEDIASTAT 0x006C /* 8 bits */ #define RE_GMEDIASTAT_FDX 0x01 /* full duplex */ #define RE_GMEDIASTAT_LINK 0x02 /* link up */ #define RE_GMEDIASTAT_10MBPS 0x04 /* 10mps link */ #define RE_GMEDIASTAT_100MBPS 0x08 /* 100mbps link */ #define RE_GMEDIASTAT_1000MBPS 0x10 /* gigE link */ #define RE_GMEDIASTAT_RXFLOW 0x20 /* RX flow control on */ #define RE_GMEDIASTAT_TXFLOW 0x40 /* TX flow control on */ #define RE_GMEDIASTAT_TBI 0x80 /* TBI enabled */ #endif /* !_DEV_RGEPHY_MIIREG_H_ */
