/*      $OpenBSD: rtl80x9.c,v 1.12 2021/03/07 06:21:38 jsg Exp $        */
/*      $NetBSD: rtl80x9.c,v 1.1 1998/10/31 00:44:33 thorpej Exp $      */

/*-
 * Copyright (c) 1998 The NetBSD Foundation, Inc.
 * All rights reserved.
 *
 * This code is derived from software contributed to The NetBSD Foundation
 * by Jason R. Thorpe of the Numerical Aerospace Simulation Facility,
 * NASA Ames Research Center.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
 * PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 */

#include "bpfilter.h"

#include <sys/param.h>
#include <sys/systm.h>
#include <sys/mbuf.h>
#include <sys/syslog.h>
#include <sys/socket.h>
#include <sys/device.h>

#include <net/if.h>
#include <net/if_media.h>

#include <netinet/in.h>
#include <netinet/if_ether.h>

#include <machine/bus.h>

#include <dev/ic/dp8390reg.h>
#include <dev/ic/dp8390var.h>

#include <dev/ic/ne2000var.h>

#include <dev/ic/rtl80x9reg.h>
#include <dev/ic/rtl80x9var.h>

int
rtl80x9_mediachange(struct dp8390_softc *dsc)
{

        /*
         * Current media is already set up.  Just reset the interface
         * to let the new value take hold.  The new media will be
         * set up in ne_pci_rtl8029_init_card() called via dp8390_init().
         */
        dp8390_reset(dsc);
        return (0);
}

void
rtl80x9_mediastatus(struct dp8390_softc *sc, struct ifmediareq *ifmr)
{
        struct ifnet *ifp = &sc->sc_arpcom.ac_if;
        u_int8_t cr_proto = sc->cr_proto |
            ((ifp->if_flags & IFF_RUNNING) ? ED_CR_STA : ED_CR_STP);

        /*
         * Sigh, can detect which media is being used, but can't
         * detect if we have link or not.
         */

        /* Set NIC to page 3 registers. */
        NIC_PUT(sc->sc_regt, sc->sc_regh, ED_P0_CR, cr_proto | ED_CR_PAGE_3);

        if (NIC_GET(sc->sc_regt, sc->sc_regh, NERTL_RTL3_CONFIG0) &
            RTL3_CONFIG0_BNC)
                ifmr->ifm_active = IFM_ETHER|IFM_10_2;
        else {
                ifmr->ifm_active = IFM_ETHER|IFM_10_T;
                if (NIC_GET(sc->sc_regt, sc->sc_regh, NERTL_RTL3_CONFIG3) &
                    RTL3_CONFIG3_FUDUP)
                        ifmr->ifm_active |= IFM_FDX;
        }

        /* Set NIC to page 0 registers. */
        NIC_PUT(sc->sc_regt, sc->sc_regh, ED_P0_CR, cr_proto | ED_CR_PAGE_0);
}

void
rtl80x9_init_card(struct dp8390_softc *sc)
{
        struct ifmedia *ifm = &sc->sc_media;
        struct ifnet *ifp = &sc->sc_arpcom.ac_if;
        u_int8_t cr_proto = sc->cr_proto |
            ((ifp->if_flags & IFF_RUNNING) ? ED_CR_STA : ED_CR_STP);
        u_int8_t reg;

        /* Set NIC to page 3 registers. */
        NIC_PUT(sc->sc_regt, sc->sc_regh, ED_P0_CR, cr_proto | ED_CR_PAGE_3);

        /* write enable config1-3. */
        NIC_PUT(sc->sc_regt, sc->sc_regh, NERTL_RTL3_EECR,
            RTL3_EECR_EEM1|RTL3_EECR_EEM0);

        /* First, set basic media type. */
        reg = NIC_GET(sc->sc_regt, sc->sc_regh, NERTL_RTL3_CONFIG2);
        reg &= ~(RTL3_CONFIG2_PL1|RTL3_CONFIG2_PL0);
        switch (IFM_SUBTYPE(ifm->ifm_cur->ifm_media)) {
        case IFM_AUTO:
                /* Nothing to do; both bits clear == auto-detect. */
                break;

        case IFM_10_T:
                /*
                 * According to docs, this should be:
                 * reg |= RTL3_CONFIG2_PL0;
                 * but this doesn't work, so make it the same as AUTO.
                 */
                break;

        case IFM_10_2:
                reg |= RTL3_CONFIG2_PL1|RTL3_CONFIG2_PL0;
                break;
        }
        NIC_PUT(sc->sc_regt, sc->sc_regh, NERTL_RTL3_CONFIG2, reg);

        /* Now, set duplex mode. */
        reg = NIC_GET(sc->sc_regt, sc->sc_regh, NERTL_RTL3_CONFIG3);
        if (ifm->ifm_cur->ifm_media & IFM_FDX)
                reg |= RTL3_CONFIG3_FUDUP;
        else
                reg &= ~RTL3_CONFIG3_FUDUP;
        NIC_PUT(sc->sc_regt, sc->sc_regh, NERTL_RTL3_CONFIG3, reg);

        /* write disable config1-3 */
        NIC_PUT(sc->sc_regt, sc->sc_regh, NERTL_RTL3_EECR, 0);

        /* Set NIC to page 0 registers. */
        NIC_PUT(sc->sc_regt, sc->sc_regh, ED_P0_CR, cr_proto | ED_CR_PAGE_0);
}

void
rtl80x9_media_init(struct dp8390_softc *sc)
{
        static uint64_t rtl80x9_media[] = {
                IFM_ETHER|IFM_AUTO,
                IFM_ETHER|IFM_10_T,
                IFM_ETHER|IFM_10_T|IFM_FDX,
                IFM_ETHER|IFM_10_2,
        };
        static const int rtl80x9_nmedia =
            sizeof(rtl80x9_media) / sizeof(rtl80x9_media[0]);

        int i;
        uint64_t defmedia;
        u_int8_t conf2, conf3;

        /* Set NIC to page 3 registers. */
        bus_space_write_1(sc->sc_regt, sc->sc_regh, ED_P0_CR, ED_CR_PAGE_3);

        conf2 = bus_space_read_1(sc->sc_regt, sc->sc_regh, NERTL_RTL3_CONFIG2);
        conf3 = bus_space_read_1(sc->sc_regt, sc->sc_regh, NERTL_RTL3_CONFIG3);

        conf2 &= RTL3_CONFIG2_PL1|RTL3_CONFIG2_PL0;

        switch (conf2) {
        case 0:
                defmedia = IFM_ETHER|IFM_AUTO;
                break;

        case RTL3_CONFIG2_PL1|RTL3_CONFIG2_PL0:
        case RTL3_CONFIG2_PL1:  /* XXX rtl docs sys 10base5, but chip cant do */
                defmedia = IFM_ETHER|IFM_10_2;
                break;

        case RTL3_CONFIG2_PL0:
                if (conf3 & RTL3_CONFIG3_FUDUP)
                        defmedia = IFM_ETHER|IFM_10_T|IFM_FDX;
                else
                        defmedia = IFM_ETHER|IFM_10_T;
                break;
        }

        /* Set NIC to page 0 registers. */
        bus_space_write_1(sc->sc_regt, sc->sc_regh, ED_P0_CR, ED_CR_PAGE_0);

        ifmedia_init(&sc->sc_media, 0, dp8390_mediachange, dp8390_mediastatus);
        for (i = 0; i < rtl80x9_nmedia; i++)
                ifmedia_add(&sc->sc_media, rtl80x9_media[i], 0, NULL);
        ifmedia_set(&sc->sc_media, defmedia);
}