DEBUGOUT1
DEBUGOUT1("NVM word 0x%02x is not mapped.\n", offset);
DEBUGOUT1("ULP_CONFIG_DONE cleared after %dmsec\n", i * 10);
DEBUGOUT1("Error in ULP disable flow: %d\n", ret_val);
DEBUGOUT1("After fix-ups FlowControl is now = %x\n", hw->fc);
DEBUGOUT1("Phy ID = %x \n", hw->phy_id);
DEBUGOUT1("RTL8211:ReadBack for check, LED_CFG->data=%X\n", phy_data);
DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised);
DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
DEBUGOUT1("hw->fc = %d\n", hw->fc);
DEBUGOUT1("M88E1000 PSCR: %x \n", phy_data);
DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
DEBUGOUT1("PHY I2C Address %d is out of range.\n",
DEBUGOUT1("MDICNFG PHY ADDR %d",
DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type);
DEBUGOUT1("PHY ID 0x%X detected\n", hw->phy_id);
DEBUGOUT1("Invalid PHY ID 0x%X\n", hw->phy_id);
DEBUGOUT1(" Hash value = 0x%03X\n", hash_value);
DEBUGOUT1("Invalid effective Rx buffer size %d\n",
DEBUGOUT1("After fix-ups FlowControl is now = %x\n",
DEBUGOUT1("hw->fc.current_mode = %u\n", hw->fc.current_mode);
DEBUGOUT1("Clearing RAR[1-%u]\n", rar_count-1);
DEBUGOUT1("NVM read error: %d\n", ret_val);
DEBUGOUT1("PHY Address %d is out of range\n", offset);
DEBUGOUT1("PHY Address %d is out of range\n", offset);
DEBUGOUT1("autoneg_advertised %x\n", phy->autoneg_advertised);
DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
DEBUGOUT1("Added a multicast address to RAR[%d]\n", i);
DEBUGOUT1(" Hash value = 0x%03X\n", hash_value);
DEBUGOUT1("Clearing RAR[1-%d]\n", rar_entries - 1);
DEBUGOUT1("Added a secondary address to RAR[%d]\n", rar);
DEBUGOUT1(" bit-vector = 0x%03X\n", vector);
DEBUGOUT1("Buffer length failure buffersize=%d.\n", length);
DEBUGOUT1("Buffer length failure buffersize=%d.\n", length);
DEBUGOUT1("Set up FC; PCS1GLCTL = 0x%08X\n", reg);
DEBUGOUT1("Set up FC; PCS1GLCTL = 0x%08X\n", reg);
DEBUGOUT1("Flow control setup failed, returning %d\n", ret_val);
DEBUGOUT1("Failed to initialize HW, STATUS = %d\n", status);
DEBUGOUT1("RAR index %d is out of range.\n", rar);
DEBUGOUT1("RAR index %d is out of range.\n", rar);
DEBUGOUT1("DELAY: %d MS\n", edata);
DEBUGOUT1("Unable to validate PHY address 0x%04X\n",
DEBUGOUT1("PHY ID HIGH is 0x%04X\n", phy_id);
DEBUGOUT1("MC Addr Count = %d\n", mc_addr_count);
DEBUGOUT1("Hash value = 0x%03X\n", vector);
DEBUGOUT1("Issuing host interface command failed with Status = %d\n",
DEBUGOUT1("Host interface command returned 0x%08x , returning IXGBE_ERR_FW_RESP_INVALID\n",
DEBUGOUT1("Failed to stop adapter, STATUS = %d\n", status);
DEBUGOUT1("Failed to initialize PHY ops, STATUS = %d\n",
DEBUGOUT1("Failed to start the external PHY, STATUS = %d\n",
DEBUGOUT1("Reset HW failed, STATUS = %d\n", status);
DEBUGOUT1("Could not acquire SWFW semaphore, Status = %d\n",
DEBUGOUT1("Could not acquire PHY token, Status = %d\n",
DEBUGOUT1("Unable to retry acquiring the PHY token, Status = %d\n",
DEBUGOUT1("Semaphore acquisition retries failed!: PHY ID = 0x%08X\n",