// SPDX-License-Identifier: GPL-2.0
//
// Copyright 2008 Openmoko, Inc.
// Copyright 2004-2008 Simtec Electronics
//      Ben Dooks <ben@simtec.co.uk>
//      http://armlinux.simtec.co.uk/
//
// S3C common power management (suspend to ram) support.

#include <linux/init.h>
#include <linux/suspend.h>
#include <linux/errno.h>
#include <linux/delay.h>
#include <linux/of.h>
#include <linux/serial_s3c.h>
#include <linux/io.h>

#include <asm/cacheflush.h>
#include <asm/suspend.h>

#include "map.h"
#include "regs-clock.h"
#include "regs-irq.h"
#include "irqs.h"

#include <asm/irq.h>

#include "cpu.h"
#include "pm.h"
#include "pm-core.h"

/* for external use */

unsigned long s3c_pm_flags;

/* The IRQ ext-int code goes here, it is too small to currently bother
 * with its own file. */

unsigned long s3c_irqwake_intmask       = 0xffffffffL;
unsigned long s3c_irqwake_eintmask      = 0xffffffffL;

int s3c_irqext_wake(struct irq_data *data, unsigned int state)
{
        unsigned long bit = 1L << IRQ_EINT_BIT(data->irq);

        if (!(s3c_irqwake_eintallow & bit))
                return -ENOENT;

        printk(KERN_INFO "wake %s for irq %d\n",
               state ? "enabled" : "disabled", data->irq);

        if (!state)
                s3c_irqwake_eintmask |= bit;
        else
                s3c_irqwake_eintmask &= ~bit;

        return 0;
}

void (*pm_cpu_prep)(void);
int (*pm_cpu_sleep)(unsigned long);

#define any_allowed(mask, allow) (((mask) & (allow)) != (allow))

/* s3c_pm_enter
 *
 * central control for sleep/resume process
*/

static int s3c_pm_enter(suspend_state_t state)
{
        int ret;
        /* ensure the debug is initialised (if enabled) */
        s3c_pm_debug_init_uart();

        S3C_PMDBG("%s(%d)\n", __func__, state);

        if (pm_cpu_prep == NULL || pm_cpu_sleep == NULL) {
                printk(KERN_ERR "%s: error: no cpu sleep function\n", __func__);
                return -EINVAL;
        }

        /* check if we have anything to wake-up with... bad things seem
         * to happen if you suspend with no wakeup (system will often
         * require a full power-cycle)
        */

        if (!of_have_populated_dt() &&
            !any_allowed(s3c_irqwake_intmask, s3c_irqwake_intallow) &&
            !any_allowed(s3c_irqwake_eintmask, s3c_irqwake_eintallow)) {
                printk(KERN_ERR "%s: No wake-up sources!\n", __func__);
                printk(KERN_ERR "%s: Aborting sleep\n", __func__);
                return -EINVAL;
        }

        /* save all necessary core registers not covered by the drivers */

        if (!of_have_populated_dt()) {
                samsung_pm_save_gpios();
                samsung_pm_saved_gpios();
        }

        s3c_pm_save_uarts(false);
        s3c_pm_save_core();

        /* set the irq configuration for wake */

        s3c_pm_configure_extint();

        S3C_PMDBG("sleep: irq wakeup masks: %08lx,%08lx\n",
            s3c_irqwake_intmask, s3c_irqwake_eintmask);

        s3c_pm_arch_prepare_irqs();

        /* call cpu specific preparation */

        pm_cpu_prep();

        /* flush cache back to ram */

        flush_cache_all();

        s3c_pm_check_store();

        /* send the cpu to sleep... */

        s3c_pm_arch_stop_clocks();

        /* this will also act as our return point from when
         * we resume as it saves its own register state and restores it
         * during the resume.  */

        ret = cpu_suspend(0, pm_cpu_sleep);
        if (ret)
                return ret;

        /* restore the system state */

        s3c_pm_restore_core();
        s3c_pm_restore_uarts(false);

        if (!of_have_populated_dt()) {
                samsung_pm_restore_gpios();
                s3c_pm_restored_gpios();
        }

        s3c_pm_debug_init_uart();

        /* check what irq (if any) restored the system */

        s3c_pm_arch_show_resume_irqs();

        S3C_PMDBG("%s: post sleep, preparing to return\n", __func__);

        s3c_pm_check_restore();

        /* ok, let's return from sleep */

        S3C_PMDBG("S3C PM Resume (post-restore)\n");
        return 0;
}

static int s3c_pm_prepare(void)
{
        /* prepare check area if configured */

        s3c_pm_check_prepare();
        return 0;
}

static void s3c_pm_finish(void)
{
        s3c_pm_check_cleanup();
}

static const struct platform_suspend_ops s3c_pm_ops = {
        .enter          = s3c_pm_enter,
        .prepare        = s3c_pm_prepare,
        .finish         = s3c_pm_finish,
        .valid          = suspend_valid_only_mem,
};

/* s3c_pm_init
 *
 * Attach the power management functions. This should be called
 * from the board specific initialisation if the board supports
 * it.
*/

int __init s3c_pm_init(void)
{
        printk("S3C Power Management, Copyright 2004 Simtec Electronics\n");

        suspend_set_ops(&s3c_pm_ops);
        return 0;
}