wl1251_error
wl1251_error("Couldn't set HW encryption");
wl1251_error("Failed to set FW rates and modulation");
wl1251_error("Couldn't set default key");
wl1251_error("chip id doesn't match after firmware boot");
wl1251_error("error reading hardware complete "
wl1251_error("timeout waiting for the hardware to "
wl1251_error("EVENT mask setting failed");
wl1251_error("firmware length not multiple of four");
wl1251_error("allocation for firmware upload chunk failed");
wl1251_error("soft reset timeout");
wl1251_error("boot failed, ECPU_CONTROL_HALT not set");
wl1251_error("VBM command failed");
wl1251_error("rx %s cmd for channel %d failed",
wl1251_error("tx %s cmd for channel %d failed",
wl1251_error("failed to initiate cmd join");
wl1251_error("cmd set_ps_mode failed");
wl1251_error("cmd scan failed: %d", ret);
wl1251_error("cmd scan status wasn't success: %d",
wl1251_error("cmd trigger scan to failed: %d", ret);
wl1251_error("command complete timeout");
wl1251_error("INTERROGATE command failed");
wl1251_error("INTERROGATE command error: %d",
wl1251_error("can not allocate mbox buffer");
wl1251_error("Power save entry failed, giving up");
wl1251_error("couldn't allocate target memory map");
wl1251_error("couldn't retrieve firmware memory map");
wl1251_error("Invalid TX queue id: %d", qid);
wl1251_error("can not allocate partition buffer");
wl1251_error("address out of range (%d)", addr);
wl1251_error("could not get nvs file: %d", ret);
wl1251_error("nvs size is not multiple of 32 bits: %zu",
wl1251_error("could not allocate memory for the nvs file");
wl1251_error("unable to register mac80211 hw: %d", ret);
wl1251_error("could not alloc ieee80211_hw");
wl1251_error("could not allocate memory for rx descriptor");
wl1251_error("unsupported chip id: 0x%x", wl->chip_id);
wl1251_error("cannot start because not in off state: %d",
wl1251_error("could not get firmware: %d", ret);
wl1251_error("firmware size is not multiple of 32 bits: %zu",
wl1251_error("Out of memory setting filters.");
wl1251_error("could not allocate memory for the firmware");
wl1251_error("Unknown key cipher 0x%x", mac80211_key->cipher);
wl1251_error("Unsupported key cmd 0x%x", cmd);
wl1251_error("Set KEY type failed");
wl1251_error("elp wakeup timeout");
wl1251_error("Couldn't allocate RX frame");
wl1251_error("sdio_writeb failed (%d)", ret);
wl1251_error("request_irq() failed: %d", ret);
wl1251_error("sdio read failed (%d)", ret);
wl1251_error("sdio write failed (%d)", ret);
wl1251_error("sdio_readb failed (%d)", ret);
wl1251_error("spi_setup failed");
wl1251_error("Failed to request gpio: %d\n", ret);
wl1251_error("irq missing in platform data");
wl1251_error("request_irq() failed: %d", ret);
wl1251_error("vio regulator missing: %d", ret);
wl1251_error("could not allocate cmd for spi reset");
wl1251_error("could not allocate cmd for spi init");
wl1251_error("invalid packet id %u", result->id);
wl1251_error("can not allocate result buffer");