nsp32_msg
nsp32_msg(KERN_INFO, "term power on");
nsp32_msg(KERN_INFO, "card disconnect");
nsp32_msg(KERN_INFO, "clean up current SCSI command");
nsp32_msg(KERN_INFO, "detected someone do bus reset");
nsp32_msg(KERN_WARNING, "SCpnt==NULL this can't be happened");
nsp32_msg(KERN_WARNING, "irq_stat=0x%x trans_stat=0x%x",
nsp32_msg(KERN_WARNING,
nsp32_msg(KERN_WARNING, "phase chg/other phase?");
nsp32_msg(KERN_WARNING, "irq_stat=0x%x trans_stat=0x%x\n",
nsp32_msg(KERN_ERR, "Received unexpected BMCNTERR IRQ! ");
nsp32_msg(KERN_WARNING, "unexpected bus free occurred");
nsp32_msg(KERN_ERR, "resid underflow");
nsp32_msg(KERN_ERR, "Target or Lun is invalid");
nsp32_msg(KERN_WARNING,
nsp32_msg (KERN_WARNING,
nsp32_msg (KERN_WARNING,
nsp32_msg(KERN_WARNING,
nsp32_msg(KERN_ERR, "limit_entry exceeds syncnum!");
nsp32_msg(KERN_ERR, "unknown state designation");
nsp32_msg(KERN_WARNING, "wait REQ timeout, req_bit: 0x%x", req_bit);
nsp32_msg(KERN_ERR, "unknown state designation");
nsp32_msg(KERN_WARNING, "wait SACK timeout, ack_bit: 0x%x", ack_bit);
nsp32_msg (KERN_ERR, "failed to scsi register");
nsp32_msg(KERN_WARNING,
nsp32_msg (KERN_ERR, "failed to set PCI DMA mask");
nsp32_msg(KERN_ERR, "failed to allocate DMA memory");
nsp32_msg(KERN_ERR, "failed to allocate DMA memory");
nsp32_msg(KERN_ERR, "Unable to allocate IRQ for NinjaSCSI32 "
nsp32_msg(KERN_ERR,
nsp32_msg(KERN_ERR, "failed to add scsi host");
nsp32_msg(KERN_WARNING, "abort");
nsp32_msg(KERN_INFO, "Host Reset");
nsp32_msg(KERN_INFO, "No EEPROM detected: 0x%x", ret);
nsp32_msg(KERN_INFO, "Invalid number: 0x%x", ret);
nsp32_msg(KERN_WARNING, "Unknown EEPROM");
nsp32_msg(KERN_WARNING,
nsp32_msg(KERN_ERR, "return value is not appropriate");
nsp32_msg(KERN_INFO, "pci-suspend: pdev=0x%p, state.event=%x, slot=%s, host=0x%p",
nsp32_msg(KERN_INFO, "pci-resume: pdev=0x%p, slot=%s, host=0x%p",
nsp32_msg(KERN_INFO, "io=0x%x reg=0x%x", data->BaseAddress, reg);
nsp32_msg(KERN_INFO, "missing device. abort resume.");
nsp32_msg(KERN_INFO, "resume success");
nsp32_msg(KERN_ERR, "failed to enable pci device");
nsp32_msg(KERN_INFO, "irq: %i mmio: %p+0x%lx slot: %s model: %s",
nsp32_msg(KERN_INFO, "loading...");
nsp32_msg(KERN_INFO, "unloading...");
nsp32_msg(KERN_WARNING,
nsp32_msg(KERN_WARNING, "bus busy");
nsp32_msg(KERN_ERR, "SCSI MsgOut without any message!");
nsp32_msg(KERN_ERR, "unknown trans_method");
nsp32_msg(KERN_WARNING, "bus busy");
nsp32_msg(KERN_ERR, "SCSI MsgOut without any message!");
nsp32_msg(KERN_WARNING, "unknown id/lun");
nsp32_msg(KERN_WARNING, "no SCSI command is processing");
nsp32_msg(KERN_ERR,
nsp32_msg(KERN_ERR, "Currentsc != NULL. Cancel this command request");
nsp32_msg(KERN_ERR, "SGT fail");