/* * CDDL HEADER START * * The contents of this file are subject to the terms of the * Common Development and Distribution License (the "License"). * You may not use this file except in compliance with the License. * * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE * or http://www.opensolaris.org/os/licensing. * See the License for the specific language governing permissions * and limitations under the License. * * When distributing Covered Code, include this CDDL HEADER in each * file and include the License file at usr/src/OPENSOLARIS.LICENSE. * If applicable, add the following below this CDDL HEADER, with the * fields enclosed by brackets "[]" replaced with your own identifying * information: Portions Copyright [yyyy] [name of copyright owner] * * CDDL HEADER END */ /* * Copyright 2007 Sun Microsystems, Inc. All rights reserved. * Use is subject to license terms. */ #ifndef _BOOT_SERIAL_H #define _BOOT_SERIAL_H #ifdef __cplusplus extern "C" { #endif /* ---- ports on 16550 serial chips ---- */ #define DAT 0 /* ... data */ #define ICR 1 /* ... intr control reg */ #define ISR 2 /* ... intr status reg */ #define LCR 3 /* ... line control reg */ #define MCR 4 /* ... modem control reg */ #define LSR 5 /* ... line status reg */ #define MSR 6 /* ... modem status reg */ #define DLL 0 /* ... data latch low (used for baud rate) */ #define DLH 1 /* ... data latch high (ditto) */ #define FIFOR ISR /* ... fifo write reg */ /* ---- LSR bits ---- */ #define RCA 0x01 /* ... receive char avail */ #define XHRE 0x20 /* ... xmit hold buffer empty */ /* ---- Modem bits ---- */ #define DTR 0x01 #define RTS 0x02 #define OUT2 0x08 #define FIFO_ON 0x01 #define FIFO_OFF 0x00 #define FIFORXFLSH 0x02 #define FIFOTXFLSH 0x04 #define FIFODMA 0x08 /* ---- LCR bits ---- */ #define STOP1 00 #define STOP2 0x04 #define BITS5 0x00 /* 5 bits per char */ #define BITS6 0x01 /* 6 bits per char */ #define BITS7 0x02 /* 7 bits per char */ #define BITS8 0x03 /* 8 bits per char */ /* baud rate definitions */ #define DLAB 0x80 /* divisor latch access bit */ #define ASY110 1047 /* 110 baud rate for serial console */ #define ASY150 768 /* 150 baud rate for serial console */ #define ASY300 384 /* 300 baud rate for serial console */ #define ASY600 192 /* 600 baud rate for serial console */ #define ASY1200 96 /* 1200 baud rate for serial console */ #define ASY2400 48 /* 2400 baud rate for serial console */ #define ASY4800 24 /* 4800 baud rate for serial console */ #define ASY9600 12 /* 9600 baud rate for serial console */ #define ASY19200 6 /* 19200 baud rate for serial console */ #define ASY38400 3 /* 38400 baud rate for serial console */ #define ASY57600 2 /* 57600 baud rate for serial console */ #define ASY115200 1 /* 115200 baud rate for serial console */ /* * Defines for the serial port */ #define SERIAL_FIFO_FLUSH 16 /* maximum number of chars to flush */ /* ---- Bit 11 defines direct serial port ---- */ #define SDIRECT 0x1000 /* ---- Bits 9-10 define flow control ---- */ #define SSOFT 0x800 #define SHARD 0x400 /* ---- Bits 5-8 define baud rate ---- */ #define S110 0x00 #define S150 0x20 #define S300 0x40 #define S600 0x60 #define S1200 0x80 #define S2400 0xa0 #define S4800 0xc0 #define S9600 0xe0 #define S19200 0x100 #define S38400 0x120 #define S57600 0x140 #define S76800 0x160 #define S115200 0x180 #define S153600 0x1a0 #define S230400 0x1c0 #define S307200 0x1e0 #define S460800 0x200 /* ---- Bits 3 & 4 are parity ---- */ #define PARITY_NONE 0x10 #define PARITY_ODD 0x08 #define PARITY_EVEN 0x18 /* ---- Bit 2 is stop bit ---- */ #define STOP_1 0x00 #define STOP_2 0x04 /* ---- Bits 0 & 1 are data bits ---- */ #define DATA_8 0x03 #define DATA_7 0x02 #define DATA_6 0x01 #define DATA_5 0x00 /* ---- Line Status ---- */ #define SERIAL_TIMEOUT 0x80 #define SERIAL_XMITSHFT 0x40 #define SERIAL_XMITHOLD 0x20 #define SERIAL_BREAK 0x10 #define SERIAL_FRAME 0x08 #define SERIAL_PARITY 0x04 #define SERIAL_OVERRUN 0x02 #define SERIAL_DATA 0x01 #ifdef __cplusplus } #endif #endif /* _BOOT_SERIAL_H */
