SES_LOG
SES_LOG(ssc, SES_CE_DEBUG9, "ses_start -> scsi_transport");
SES_LOG(ssc, SES_CE_DEBUG2,
SES_LOG(ssc, SES_CE_DEBUG2, "TRANSPORT ERROR\n");
SES_LOG(ssc, SES_CE_DEBUG9, "ses_restart");
SES_LOG(ssc, SES_CE_DEBUG9,
SES_LOG(ssc, SES_CE_DEBUG1,
SES_LOG(ssc, SES_CE_DEBUG1,
SES_LOG(ssc, SES_CE_DEBUG6,
SES_LOG(ssc, CE_WARN, fail_msg,
SES_LOG(ssc, CE_WARN, fail_msg,
SES_LOG(ssc, SES_CE_DEBUG1, "retrying cmd");
SES_LOG(ssc, SES_CE_DEBUG1, "retrying sense");
SES_LOG(ssc, SES_CE_DEBUG4, "cmd done");
SES_LOG(ssc, SES_CE_DEBUG6,
SES_LOG(ssc, SES_CE_DEBUG1, "SES: ERROR %d\n", err);
SES_LOG(ssc, SES_CE_DEBUG3, "status decode: check");
SES_LOG(ssc, SES_CE_DEBUG1, "status decode: busy");
SES_LOG(ssc, SES_CE_DEBUG1, "status decode: reserved");
SES_LOG(ssc, SES_CE_DEBUG1, "status decode: terminated");
SES_LOG(ssc, SES_CE_DEBUG1, "status 0x%x", status);
SES_LOG(ssc, SES_CE_DEBUG1,
SES_LOG(NULL, SES_CE_DEBUG9,
SES_LOG(NULL, SES_CE_DEBUG9, "ses_attach: DDI_ATTACH ses%d",
SES_LOG(NULL, SES_CE_DEBUG4,
SES_LOG(ssc, SES_CE_DEBUG1, "ses_attach: DDI_ATTACH ses%d",
SES_LOG(ssc, SES_CE_DEBUG3, "SEN device found");
SES_LOG(ssc, SES_CE_DEBUG3, "SES device found");
SES_LOG(ssc, SES_CE_DEBUG3, "Pre-SCSI3 SES device");
SES_LOG(ssc, SES_CE_DEBUG3, "Passthru SES device");
SES_LOG(ssc, CE_NOTE,
SES_LOG(ssc, SES_CE_DEBUG3, "SAF-TE device found");
SES_LOG(NULL, SES_CE_DEBUG9,
SES_LOG(NULL, CE_WARN,
SES_LOG(NULL, CE_NOTE, "ses%d: softalloc fails", inst);
SES_LOG(NULL, CE_NOTE, "ses%d: get_soft_state fails", inst);
SES_LOG(ssc, CE_NOTE, "minor node creation failed");
SES_LOG(ssc, CE_NOTE, "scsi_init_pkt of rqbuf failed");
SES_LOG(ssc, SES_CE_DEBUG3, "failed softc init");
SES_LOG(ssc, SES_CE_DEBUG1, "ses_uscsi_cmd: "
SES_LOG(ssc, SES_CE_DEBUG2, efl, __LINE__);
SES_LOG(ssc, SES_CE_DEBUG7,
SES_LOG(ssc, SES_CE_DEBUG7,
SES_LOG(ssc, SES_CE_DEBUG9, "ses_start");
SES_LOG(ssc, SES_CE_DEBUG2, "saf_wrbuf16 %x %x %x %x", op, b1, b2, b3);
SES_LOG(ssc, SES_CE_DEBUG2, "saf_wrslot");
SES_LOG(ssc, SES_CE_DEBUG2, "saf_wrslot %d <- %x", i,
SES_LOG(ssc, SES_CE_DEBUG2, "saf_slotop slot %d op %x", slot, opflag);
SES_LOG(ssc, CE_NOTE, "Too little data (%ld) for configuration",
SES_LOG(ssc, SES_CE_DEBUG1, "Nfans %d Npwr %d Nslots %d Lck %d Ntherm "
SES_LOG(ssc, CE_NOTE, toolittle, x, __LINE__); \
SES_LOG(ssc, CE_NOTE, "unknown fan%d status 0x%x",
SES_LOG(ssc, CE_NOTE, "unknown pwr%d status 0x%x",
SES_LOG(ssc, CE_NOTE, "unknown lock status 0x%x",
SES_LOG(ssc, CE_NOTE, "unknown spkr status 0x%x",
SES_LOG(ssc, SES_CE_DEBUG2, "safte_set_objstat(%d): %x %x %x %x",
SES_LOG(ssc, CE_NOTE, "sen_rdstat: too little data (%ld)",
SES_LOG(ssc, CE_NOTE, "Too Little Data Returned (%ld)",
SES_LOG(ssc, SES_CE_DEBUG1, "faulted %d", idx);
SES_LOG(ssc, SES_CE_DEBUG1, "clrd fault on %d", idx);
SES_LOG(ssc, CE_WARN, "Commanding Off Power Supply!");
SES_LOG(ssc, SES_CE_DEBUG1, "%sabling alarm",
SES_LOG(ssc, CE_NOTE, "Unable to parse SES Config Header");
SES_LOG(ssc, CE_NOTE, "runt enclosure length (%d)", amt);
SES_LOG(ssc, SES_CE_DEBUG3, "GenCode %lx %d Subenclosures",
SES_LOG(ssc, CE_NOTE,
SES_LOG(ssc, SES_CE_DEBUG3,
SES_LOG(ssc, CE_NOTE,
SES_LOG(ssc, SES_CE_DEBUG3,
SES_LOG(ssc, CE_NOTE,
SES_LOG(ssc, SES_CE_DEBUG3,
SES_LOG(NULL, SES_CE_DEBUG5, "Get Elt 0x%x Elm 0x%x (idx %d)",
SES_LOG(NULL, SES_CE_DEBUG5, "set EncStat %x", sp->comstatus);
SES_LOG(NULL, SES_CE_DEBUG2, "Set Elt 0x%x Elm 0x%x (idx %d) with "